Used Profile Sanding Machine for sale (94,495)

Condition: new, Number of sanding units 2 St. sanding width 190 mm Sanding height max. 2-180 mm LÖWER double-sided grinding machine DSM 2000 ----- Double-sided single wood sander for sanding Solid wood such as window wood etc. Stable top quality Guide with long casting tables, brushing and finishing equipment and conveyor belt feed. Suitable for high continuous loads Ibedpfxovu Hdtj Afiec even with higher chip removals. - Staggered sanding and finishing units at the top and bottom - Directly driven rubberized grinding rollers for slip-free power transmission - Combined grinding via roller and shoe for high chip removal at the same time flat intervention zone - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute Dimensional accuracy - External cooling of the grinding zones for cooler grinding and higher grinding Grinding belt service life - Forced pneumatically controlled sanding belt oscillation - effective sanding dust extraction directly on the sanding rollers Airborne dust extraction on the tension rollers - Integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large-sized linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of the chip removal at the bottom using a precision threaded spindle Dimension display via scale ring (resolution 0.1mm) - Sanding belt tension via pneumatic cylinders with constant clamping pressure - Sanding belt change with pneumatic belt relaxation in seconds - Adjustment of the sanding belt run when changing the belt - electro-pneumatic compressed air monitoring - Run-in protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and non-stick conveyor belts over heavy, 1000mm long cast tables with a finely planed surface and Spring-loaded pressure rollers with fine adjustment - Cardan shaft drive for smooth and even workpiece transport - Feed gear motor with three different feed speeds for quick adaptation to different types of wood - all motors electrically protected - Ergonomically arranged controls on the workpiece inlet side - automatic workpiece thickness scanning (no previous measurement necessary) - Digital thickness display (resolution 0.1mm) with modern magnetic tape system Technical data: - Sanding belt speed: 22 m/s - Sanding belt length: 1800mm - Sanding belt width: 200mm - Working width: 190mm - Grinding thickness: 2-180mm - two brake motors for drive: 5.5 kW - Feed motor: 1.0 kW - Feed speed: 6, 11 and 16 m/min. - automatic height adjustment: 0.37 kW - two brush units with fiber brushes D 120 x 200mm at 0.37 kW - Suction nozzle: 2 x 120mm and 2 x 150mm - Pneumatic connection 6 bar - Working height: 850mm - Length: 2105mm - Length with control panel 2490mm - Width: 880mm - Height: 1910mm - Weight: approx. 1500 kg - Operating voltage: 400 volts, 50 Hz, 3P - CE version ----- ----- Basic price of the machine on request! ----- ----- Special accessories with surcharge: continuous feed 4-20 m/min. for speed adjustment to the previous machine Price on request Workpiece blow-off - using nozzles from above and below at the machine ...

Condition: excellent (used), METALLKRAFT Profile Steel Shear / Punch HPS 65 DS Combined Hydraulic Profile Steel Shear and Punch with Punching Station, Notching Station, and Flat Steel, Angle Steel, and Profile Steel Shear – enables simultaneous operation at punching and profile steel shear. Punching Station - Punching Force: 65 t - Punching Capacity: max. Ø 26 x 20 / Ø 57 x 10 mm* - Throat Depth: 305 mm - Stroke Length: max. 55 mm - Number of Strokes: 25 strokes/min - Working Height: 900 mm Rod Steel Shear - Cutting Capacity Round: max. Ø 45 mm* - Cutting Capacity Square: max. 45 x 45 mm* Angle Steel Shear - Cutting Capacity L-Profile 90°: 120 x 120 x 12 mm* - Cutting Capacity L-Profile 45°: 70 x 10 mm* - Cutting Capacity U/I Profile: 120 x 58 mm - Cutting Capacity T-Profile: 90 x 11 mm - Working Height: 1,140 mm Flat Steel Shear - Cutting Capacity 90°: max. 300 x 20 / 375 x 15 mm* - Miter Cut 45°: max. FL 100 x 15 mm* - Blade Length: 380 mm - Working Height: 900 mm Notching Station - Material Thickness: max. 10 mm* - Notching Width: max. 45 mm - Notching Depth: max. 90 mm - Notching Station: 100 x 100 x 10 mm Machine Data - Motor Power: 5.5 kW | 400 V - 50 Hz - Dimensions (LxWxH): 1700 x 950 x 1880 mm - Weight (net): approx. 1,600 kg Shipping on pallet via freight forwarder possible Europe-wide. Additional machines available! Take a look at our listings. If you have any questions, feel free to contact us by message or phone: Maschinenhandel Nord Gerstenstraße 2 17034 Neubrandenburg Isdpfx Afoxizaneijbc

Condition: excellent (used), functionality: fully functional, Year of construction: 2020, BPR BA 35 CNC Three-Roller Ring Bending Machine, Hydraulic AS-NEW CONDITION MACHINE Shaft diameter: 35 mm Roller diameter: mm on request Shafts made of high-strength steel, hardened and ground Iedpsxivfxofx Afisbc Drive motor: 1.1 kW, 50 Hz Hydraulic pump motor: 3 kW Shaft rotation (variable): 0-30 rpm Working position: horizontal and vertical Separate control panel External dimensions: 740 x 1020 x 1110 mm Control panel dimensions: 600 x 710 x 1120 mm Weight: 490 kg Hydraulic adjustment of the side roller Three powered rollers with smooth surface BPR Probending CNC electronic control system Hydraulic cylinder pressing force: 5,500 kg Working pressure: 190 bar

Condition: good (used), Year of construction: 2000, Special-purpose machine, not a through-feed machine but a support machine, approximately 150 cm long where the workpiece is clamped. 4 units positioned transversely to the feed direction. It was used for intermediate sanding of polyester lacquer to achieve high-gloss finishes on dashboard panels for luxury cars. The total machine length is 12 m. Ibjdpfx Aexivbmefiec

Condition: used, Edge sanding machine Gartner FLK 4 - used - including mitre fence ----- Technical Data ----- Sanding belt width: 200 mm, sanding belt length: 2,350 mm, worktable dimensions: 870 x 400 mm, belt speeds: 4, extraction nozzle Ø: 80 mm, motor: 3 kW Ijdpfxoxd U Uhe Afisbc

Condition: excellent (used), Belt sander Make Karnasch Type ALMI AL 100 with 6 different contact rollers or sanding rollers Isdpeuf N Scjfx Afiebc Diameter : 17,5 - 20 - 22 - 28 - 38 - 48 mm belt width 100 mm length 2000 mm Grinding range for grinding diameter 20 - 76 mm

Condition: new, Number of sanding units 8 st. sanding width 180 (260) mm Sanding height max. 160 mm Dimensions (L/W/H) 3065x1600x1900 mm weight of the machine ca. 1500 kg LÖWER Leistomat SD ----- Automatic fine grinding machine for wood grinding (smoothing, defibering and Edge breaking) or intermediate sanding of profiled window bars. With soft disc Technology for the visible surfaces as well as automatically safe profile and Width adjustment. - 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm 1 softisc unit Ø=200mm above 0.75kW, 1 slat roller unit L=200mm top 0.75kW, 1 soft disc unit Ø=200mm bottom 0.75kW, 1 slat roller unit L=200mm bottom 0.75kW, 2 lamella roller units on the side, each 0.75kW, L=120mm, D=200mm - Linear guidance of all grinding units Linear ball bearing sets on hardened shafts - time-controlled immersion of all lamella roller units directly above the incoming workpiece edges. By the It is possible to immerse the aggregates deeper into the profiles to be able to deliver. - Motorized workpiece thickness adjustment of the machine - variable grinding flap speed via frequency converter for adjusting the grinding intensity using frequency converters (separate for discs, surface rollers and side rollers) - Disc aggregates as soft discs with Velcro fastener for Grinding wheels (wood pulp) - Feed via three lower and one upper conveyor belts and Spring-loaded pressure rollers with infinitely variable speed 4-15m/min - Parameters that can be set using the touch panel are workpiece thickness, Workpiece width (left side units individually), immersion depth Side units, spindle speed, feed speed - Saving the parameters as machine programs in program mode - Working in automatic mode with non-contact Workpiece width detection and profile detection as well as automatic Adjustment of the sanding units to the workpiece width and the Profile shape (workpiece height is set in advance) - pneumatically clocked driven feed roller, automatic Clamping of the workpiece and feeding in after unit adjustment - Red/green indicator lights to indicate operational readiness - shortest workpiece length 380mm - Transport belt width 200mm - max. workpiece width 180mm (260mm in the envelope process) - Workpiece height 12-160mm - Suction connection 4 x 100mm and 2x80mm diameter - Sensor-controlled tool blow-off directly on the discs - Length (case) x width x height (mm): 3065x 1600 x 1900 Complete length: 4365mm (including roller conveyor with integrated workpiece width detection) - Weight: 1500kg - Operating voltage 400V, 50Hz, 3P, air connection 6 bar - CE version ----- Price of the above machine on request! Isdpfx Afjvnv Uhsijbc ----- Special accessories with additional costs: Set of replacement slats for Leistomat SD-200 consisting of Area aggregates: 30 strips EH45 / 200 - 7 (rolls) 30 strips EH45 / 200 - 20 (rolls) Folding units: 96 strips M55 / 120 - 4 SmartFlex slat disc Ø200 solid with 30 grooves 50mm long Set of replacement slats for SmartFlex slat disc consisting of 60 strip M35 / 50 K 180-7 p Sandpaper disc VB for soft disc D=200mm grit 220 with velor backing (Velcro), pack of 100. Sandpaper disc VB for soft disc D=200mm grit 280 with velor backing (Velcro), pack of 100. ----- Price of the above-mentioned special accessories on request! -----...

Condition: used, WEMA Probst profile milling machine Hauptmtor 11kW Isdpfxec N N U No Afijbc dismantled and reverse loading ready

Condition: excellent (used), Technical specifications: 2 hydraulically adjustable rolls 3 driven rolls Roll diameter: 225 mm Shaft diameter: 75 mm Round steel: diameter 50 mm Square steel: 45 x 45 mm Flat steel: 200 x 20 mm Ibjdpfxoxgukus Afijc Angle steel: 75 x 15 mm Bending speed: 7 m/min Motor power: 4 kW Machine can operate horizontally or vertically Dimensions (L x W x H): approx. 1200 x 1100 x 1200 mm Weight: approx. 1.3 t The seller assumes no liability for typographical or data transmission errors. The machine's appearance, technology, and wear are consistent with its age; used machines are sold without any warranty.

Condition: used, Year of construction: 1973, functionality: fully functional, ARMINIUS profile sanding machine type 171/2, year 1973, with 3 units. All spindles 30 mm diameter. Spindles adjustable in depth and height. 1 spindle 7900 rpm. Accessories: various profile grinding wheels, feed unit with 3 rollers. Sold without warranty. Ijdpfexgp E Hjx Afiebc

Condition: new, Year of construction: 2004, 30 mm 30 mm flat steel 50 x 10 mm L-beam 40 x 40 x 5 mm Ibsdpjw Tdxpefx Afijc Axis diameter 30 mm roll diameter -toolpieces 132 mm total power requirement 0,75 kW weight of the machine ca. 0,19 Kg dimensions of the machine ca. 1,2 x 0,8 x 1,4 m Profile bending machine with: - 1 set of standard rollers - 2 rollers are driven - Foot switch - Emergency stop device

Condition: new, The new cylinder brush and sanding machine from Holzprofi Maker can be quickly and easily converted from a sanding machine to a brushing machine in just a few seconds. It is ideal for smaller workshops as it combines two machines in one. Advantages and Features: - Versatile options for surface finishing - Quick and easy changeover from sanding to brushing - Many different brushes available for a wide range of effects and processing possibilities - Infinitely variable feed rate and roller speed for perfect results - Workpiece width up to approx. 1100 mm - Precise adjustment of sanding height for consistent results Technical Data: Sanding width: 560 mm (1120 mm) Sanding height: 3 to 75 mm Roller diameter: Ø132 mm Table dimensions: 592x530 mm Extension table dimensions (2x): 582x245 mm Roller speed: 0 to 1800 rpm Feed speed: 0 to 7.5 m/min Extraction port diameter: 100 mm Main motor power: 1.5 kW Feed motor power: 120 W Voltage: 230 V Dimensions: 1010x1060x1190 mm Weight: 155 kg Optional Accessories: Texturing brush for even and structured surfaces Abrasive flap brush for finishing and surface preparation tasks Steel wire brush for a used-look finish and pronounced grain effect Iedowzzivspfx Afijbc

Condition: used, Number of sanding units 4 St sanding width 190 mm Sanding height max. 4-180 mm weight 4200 kg Hess Expert 4-belt single wood sanding machine machine will be checked by our technicians ----- Ø Grinding at the bottom/top Ø With 2 offset grinding units each (bottom and top) Ø Grinding units (bottom and top) connected in series according to the Dressing principle Ø Pre-sanding with coarse grit (calibrate) Ø Regrinding with fine grit (finish) Ø Central motorized height adjustment of the lower grinding units Ø Central motorized and synchronous height adjustment of the entire upper Ijdpfxot Tqy Ee Afiebc Grinding and brushing units including the upper transport units Ø Oscillating sanding belt utilization (during the sanding process) Ø Absolute power connection thanks to 5.5 KW motors and large dimensions drive drums Ø Oxide ceramic grinding shoe for - exact surface geometry - no adjustment work - permanent dimensional accuracy - completely maintenance and wear-free Basic structure: Stable, heavy welded construction made of strong-walled rectangular profiles additional, statically calculated reinforcements for optimal Vibration dampening. Staggered grinding units with large dimensions Belt drive drums for slip-free belt running. Two-point suction for direct and flying dust with sealing brushes and integrated sanding belt blow-off Device to increase the service life of the sanding belts. Grinding units in heavy steel plate construction as the basis for vibration-damped, quiet tape running. Absolutely backlash-free guides as ball linear sets hardened and ground shafts. Height adjustment of the grinding units via hardened and ground special linear guides as well as pre-tensioned ones Guide carriage. Permanent precision thanks to dust and dirt protection Ball linear sets and guide carriages. Large-sized pre-grinding rollers as contact rollers. Contact rollers and Sanding shoes in a balanced ratio to the sanding belt grain load. The large drive drums guarantee full transmission the 5.5 kW drive power of the grinding motors on the sanding belt. Therefore Slip-free, stable running and optimal heat dissipation. This makes it the strongest Chip removal possible. Automatic machine stop activation in the event of a belt break. Visual display on the control panel and via flashing lights on the machine. Sanding shoes for finish completely maintenance-free and wear-free made of oxide ceramic with optimal heat dissipation. Grinding belt tension via appropriately sized compression springs. Sanding belt relaxation for belt changing using a pneumatic device sensitive, distortion-free placement of new tapes. Upper grinding unit and brush device centrally motorized Height adjustable with digital display in the control panel for the motorized Grinding thickness adjustment. Brushing and finishing device, for better surface finish, integrated into the basic machine. Two special brush rollers 150 mm Æ arranged one above the other in synchronous function for advance thrust. Separate height adjustment of the brush rollers on precise Carriage guides for post-correction of wear. Additional transport roller for Removal or further transport of the workpiece from the automatic grinding machine with the conveyor belt. Wooden guide in the inlet area for hard guide and bearings mounted on both sides pressure rollers. Safe transport of profiled workpieces on ca...

Condition: new, Year of construction: 1994, 30 mm 30 mm flat steel 50 x 10 mm Axis diameter 30 mm Iodpswrzr Esfx Afijbc work speed 6,0 U/min roll diameter -toolpieces 132 mm total power requirement 0,75 kW weight of the machine ca. 0,25 Kg dimensions of the machine ca. 0,6 x 0,8 x 1,3 m Profile bending machine with: - 1 set of standard rollers - 2 rollers are driven - Horizontal or vertical operation

Condition: used, Number of sanding units 2 st. sanding width 190 mm Sanding height max. 4-180 mm HESS - GLORIA 2 BELT SINGLE WOOD SANDING MACHINE ----- Machine is being checked! Manufacturer's description: ----- Compact design designed according to modern principles. Quiet and vibration-free operation thanks to rigid, stable machine housing and special insulation. Work safety device in accordance with the EC Machinery Directive with the "dust-tested" certificate. Offset grinding units with large-dimensioned tension rollers for good heat dissipation and stable sanding belt guidance. Sanding units with forced sanding belt oscillation. 2-point sanding dust extraction directly on the sanding roller. Airborne dust extraction on the large tension rollers. Integrated sanding belt blower for longer service life of the sanding belts. Integrated brushing and finishing device, adjustable via threaded spindle, with large dust extraction. Motorized grinding thickness adjustment of the entire upper unit via precision threaded spindles and linear ball sets on hardened and ground precision shafts with dust and dirt protection. Electronic digital display for workpiece thickness (resolution 0.1 mm). Contact roller and grinding shoe in a balanced ratio to the grinding belt grain load. Hardened and ground grinding rollers. Maintenance-free and wear-free oxide ceramic grinding shoes (DBGM) with excellent sliding properties, good heat dissipation and high dimensional accuracy. Grinding belt tension via pneumatic cylinder. Grinding belt change via pneumatically controlled belt relaxation. Ability to adjust the grinding belt run when changing the belt. Electro-pneumatic pressure monitoring of the compressed air supply with visual fault display. Automatic machine stop triggered when sanding belt breaks and by run-in protection with integrated wood thickness control. Optical display on the control panel. Feed device and proven, calibrated non-slip and non-adhesive transport belts on precisely ground tables and spring-loaded pressure rollers. Cardan shaft drive for even wood transport. Feed speed continuously adjustable. Chip removal adjustment bottom via precision threaded spindle with dimension display via scale ring (resolution 0.1 mm) Ergonomic arrangement of the operating and setting elements on the machine front: sanding unit and brush device at the top, sanding unit and brush device at the bottom, workpiece transport device, sanding thickness setting, operating display, fault display. Control and operating unit with lockable main switch built into the machine housing. All motors electrically protected against overload. Technical data: ----- Ibsdpfxsv D Rg Ds Afiec Grinding belt speed: 24 m/sec. Grinding width: 190 mm Grinding thickness: 4 - 180 mm Shortest workpiece length: 300 mm Feed speed: Continuously adjustable 5 - 25 m/min. Sanding belt dimensions: 200 mm wide 1600 mm long Electrical connection: 400 V, 3/N PE, 50 HZ Grinding units: 2 x 4 kW Feed: 0.75 kW Height adjustment: 0.18 kW Pneumatic connection: R 3/8", 80 NL, 8 bar Extraction air volume: 2 x 2000 - 2500 m3/h 20 - 25 m/sec. Extraction connection nozzle: 2 x 160 mm diameter at the top of the machine housing External dimensions: Length: 1600 mm Width: 1030 mm Height: 1820 mm Height with extraction...

Condition: new, 35 (600) mm 35 (900) mm L-beam 50 x 50 x 5 (800) mm T - beam - web outwards 60 x 7 (600) mm Axis diameter 50 mm work speed 4,5 m/min total power requirement 1,5 kW weight of the machine ca. 0,4 t dimensions of the machine ca. 1,1 x 0,8 x 1,5 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable Iedpfx Afjfv H Etoisbc - Horizontal and vertical operation - Engine with braking device

Condition: used, Number of sanding units 4 St. sanding width 190 mm Sanding height max. 180 mm Control ja weight 3300 kg Dimensions (L/W/H) 2600x920x1890 mm Dust suction hood 2x180, 2x120 mm Double sided grinding machine Löwer DSM 2004 Double-sided four-band single-wood sanding machine for sanding Ibjdpfxsvu Hgbs Afioc Solid wood, e.g. Window wood etc. Highly stable top model with innovative details. Suitable for high Continuous load even at higher chip removal rates. - Successively arranged grinding units for rough grinding, fine grinding and finish sanding, each from above and below 1. Belt sanding unit with heavy steel roller 2. Belt sanding unit with rubberised roller and shoe 3.Finish aggregate with fiber brush - Direct driven wheels for slip-free power transmission - Maintenance and wear-free CERMET-coated sanding shoes with very good thermal conductivity and absolute dimensional accuracy - Foreign cooling of the grinding zones for a cooler grinding and higher Sanding belt life - positively driven pneumatically controlled grinding belt oscillation - effective sanding dust extraction directly on the sanding rollers - Dust extraction on the tension rollers - integrated brushing and finishing device with large sanding dust extraction - Motorized grinding thickness adjustment via precision threaded spindles and large dimensioned linear ball bearing sets on hardened and ground precision shafts with dust and dirt protection - Adjustment of chip removal below via precision threaded spindle with dimension display via scale ring (resolution 0,1mm) - Grinding belt tension via pneumatic cylinder with constant clamping pressure - Abrasive belt change with pneumatic belt release in seconds - Adjustment of the grinding belt when changing the belt - Electropneumatic compressed air monitoring - Overflow protection via contact roller for workpieces that are too thick - Workpiece transport via calibrated non-slip and adhesive conveyor belts over heavy, cast tables with finely planed surface and sprung Pinch rollers with fine adjustment - Cardan shaft drive for jerk-free and uniform workpiece transport - Feed gear motor with stepless speed 4-20 m / min - all motors are electrically protected - ergonomically arranged controls - digital strength display (resolution 0.1mm) with modern magnetic tape system Technical specifications: - Sanding belt speed 22 m / s - Sanding belt length 1800mm - Sanding belt width 200mm - Working width 190mm - Abrasive thickness 2-180mm - four brake motors for drive 5.5 kW - Feed motor 1.5 kW - Feed rate 4-20 m / min. - automatic height adjustment 0.37 kW - two brush sets with fiber brushes D 120 x 200mm à 0.37 kW - Exhaust nozzle 2 x 180mm 2 x 120mm - Extraction air speed 20 m / s - Pneumatic connection 6 bar - Working height 870mm - Length (with Softdisc 2740mm) 2600mm - Length with control panel (with Softdisc 3035mm) 2985mm - width 880mm - height 1910mm - Weight about 3300 kg - Operating voltage 400 volts, 50 Hz, 3P - CE version Equipped with the following options: - Sanding belt blow 4-band via nozzles directly at the radii of the tensioning rollers within the extraction system arranged, separately switchable - Disc unit for defibering - two grinding disc discs with 200 mm diameter (maximum grinding width 180 mm) - adjustable laterally and in delivery - including frequency converter for stepless speed regulation instead ...

Condition: new, 75 (800) mm 60 (750) mm L-beam 80 x 80 x 8 (800) mm T - beam - web outwards 100 x 11 (1000) mm Ibjdpsfv H Ezjfx Afioc Axis diameter 80 mm work speed 6,0 m/min Tool diameter 242 mm total power requirement 4 kW weight of the machine ca. 1,8 t dimensions of the machine ca. 1,5 x 1,05 x 1,4 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device

Condition: new, round material 30 x 1 mm square material 30 x 30 x 1 mm 16 mm 30 x 10 mm speeds 9 U/min total power requirement 1,1 kW weight of the machine ca. 0,32 t dimensions of the machine ca. 0,82 x 0,60 x 1,26 m Electric roller profile with - 5 set of rollers 2x 20mm and 30mm for round material, 1x for flat material 1x for square material 1x for? - footswitch Iedpfx Aoh D Svnjfiobc

Condition: used, Year of construction: 2001, angle steel/side length 45 x 6 R 600 mm flat steel 70 x 12 R500 mm tube diameter 1,5" x 2 R 800 mm square bar steel 30 x 30 mm total power requirement 2,2 KW weight of the machine ca. 0,25 Kg dimensions of the machine ca. 1,85 x 1,3 x 0,7 m Multi-purpose iron twister with profile bending attachment - Two driven rollers - 2 speeds - Manual feed of the upper roller Ibsdpfx Afsv H Sc Sjiec - Incl. large number of bending tools see pictures

Condition: new, 50 (500) mm 45 (500) mm L-beam 80 x 80 x 8 (800) mm T - beam - web outwards 80 x 9 (800) mm Axis diameter 60 mm work speed 5,0 m/min Tool diameter 195 mm total power requirement 3 kW weight of the machine ca. 1,0 t dimensions of the machine ca. 1,2 x 0,9 x 1,2 m Profile bending machine with: - Foot pedal right / left - Recording: wave 50mm - with digital display - hardened special steel shafts Iodpfjfv H Ewsx Afiobc - 1 set of standard rollers - Lower rollers are driven - Upper roll up and down hydraulically deliverable - Horizontal and vertical operation - Engine with braking device

Condition: new, 35 mm 35 mm bar material dia. max. 70 x 2 mm rectangle 60 x 60 x 3 mm flat steel 60 x 10 mm Axis diameter 50 mm work speed 4,3 m/min total power requirement 1,5 kW weight of the machine ca. 0,4 t dimensions of the machine ca. 0,9 x 0,95 x 1,4 m Ibjdpfx Afsk Dvhhsisc Profile bending machine with: - Foot pedal right/left rotation - Hardened special steel shafts - 1 set of standard rollers - 2 rollers are driven

Condition: new, Year of construction: 2009, 35 (800) mm 35 (1200) mm L-beam 50 x 50 x5 (850) mm flat steel 60 x 10 (800) mm Axis diameter 50 mm work speed 4,5 m/min roll diameter -toolpieces 155 mm total power requirement 1,5 kW weight of the machine ca. 0,9 Kg dimensions of the machine ca. 0,6 x 0,9 x 1,35 m Profile bending machine with: - Foot pedal for right/left rotation - 1 set of standard rollers Ibodjwrzrfjpfx Afijc - 2 rollers are driven - Horizontal or vertical operation

Condition: new, 30 / 900 mm 30 / 900 mm L-beam 35X35X5 / 600 mm T - beam - web outwards 50x6 / 600 mm Axis diameter 40 mm work speed 4,5 m/min roll diameter 148 mm total power requirement 1,1 kW weight of the machine ca. 0,3 t dimensions of the machine ca. 0,75 x 0,6 x 1,4 m Isdpfx Afoq Adtqsiobc Electric profile roller - Either horizontal or vertical working - 1 set of hardened standard rollers - lower 2 rollers are driven - 1 set of plastic rollers for diameter 33.7mm / 1 " - Operation manual - Foot switch left / right and EMERGENCY STOP

Condition: new, Year of construction: 2009, 30 mm 30 mm L-beam 20 x 20 x 4 mm flat steel 25 x 6 mm Axis diameter 20 mm work speed 11 U/min total power requirement 0,2 kW weight of the machine ca. 80 Kg dimensions of the machine ca. 0,6 x 0,6 x 1,5 m Profile bending machine with: - Foot pedal for right/left rotation Ibjdpfx Ajv Skzdofioc - Digital display - 1 set of standard rollers - 3 rollers are driven - Horizontal or vertical operation