Used Mori Seiki Junior for sale (203)

Condition: ready for operation (used), Mori Seiki MV-Junior vertical machining center... Tool magazine for 30 tools, travel X: 560 mm; Y: 410 mm; Z: 460 mm, table size: 900x450 mm, maximum table load: 300 kg, maximum spindle speed: 8,000 rpm, total weight: 3,900 kg Nedox I D Syspfx Ad Sswh

Condition: used, Year of construction: 1996, functionality: limited functionality, travel distance X-axis: 630 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 650 mm, controller model: Fanuc MSX-516, rotational speed (max.): 12,000 rpm, The P8 power supply, valued at €1,500, was only replaced in August 2024! The spindle was repaired in 2017 and has mostly only been used for single-layer operation since then! TECHNICAL DETAILS Travel range X-axis: 630 mm Travel range Y-axis: 600 mm Travel range Z-axis: 650 mm Feed length X-axis: 630 mm Feed length Y-axis: 600 mm Nwjdpjzcuyijfx Ad Soh Feed length Z-axis: 650 mm Table width: 500 mm Table length: 500 mm Number of pallets: 2 Maximum speed: 12,000 rpm Number of tool magazine slots: 60 (BT40) MACHINE DETAILS Control: Fanuc MSX-516 Phases: 3 Frequency: 50 Hz Voltage: AC 200 V Full load current: 181 A Note: The rapid traverse rate of the X-axis is reduced by 20% to extend the service life of the telescopic guides. The sealing ring during pallet changes is likely defective. The seller temporarily resolved this by inserting a ball valve in between when the pallets needed to be changed. EQUIPMENT Documentation/Manual Chip conveyor

Condition: ready for operation (used), Year of construction: 2003, operating hours: 28,877 h, functionality: fully functional, machine/vehicle number: NH501CD0388, travel distance X-axis: 650 mm, travel distance Y-axis: 600 mm, travel distance Z-axis: 730 mm, controller model: Fanuc MGS-501, rotational speed (max.): 8,000 rpm, TECHNICAL DETAILS Travel range, X-axis: 650 mm Travel range, Y-axis: 600 mm Travel range, Z-axis: 730 mm Rapid traverse rate, X-axis: 50 m/min Rapid traverse rate, Y-axis: 50 m/min Rapid traverse rate, Z-axis: 50 m/min Maximum workpiece height: 900 mm Maximum workpiece diameter: 730 mm Nwjdpozcla Hjfx Ad Sjh Maximum workpiece weight: 500 kg Table dimensions: 500 x 500 mm Table load capacity: 500 kg Maximum spindle speed: 8,000 rpm Distance from table center to spindle nose: 100 mm Number of spindles: 1 Torque: 302 Nm Number of tool positions in the tool magazine: 60 Tool length: 500 mm Tool diameter: 120 mm Tool weight: 30 g Tool holder type for turret 1: ISO 50 MACHINE DETAILS Control system: Fanuc MGS-501 Rated apparent power: 73 kVA Input voltage: 380 V Type of input current: Three-phase Dimensions & Weight Dimensions (L x W x H): 4,900 x 2,595 x 2,770 mm Total weight: 13,200 kg Operating hours (according to diagram): 28,877 h Power-on time (according to diagram): 94,850 h EQUIPMENT CE marking Documentation/Manual Spindle speed infinitely adjustable Chip conveyor

Condition: used, Year of construction: 2011, Technical details: Nedpfx Asy S Tm Ujd Sewh standard turning dia.: 200 turning length: max. 810 mm control: MSX-701 MAPPS IV greates pass round over bed: 800 mm Max. distance between centres: 1130 mm max. turning diameter: 320 mm max. workpiecediameter: 300 mm bar material dia.: 65 mm Traverse X-Axis 1: 210 Traverse X-Axis 2: 210 mm Traverse X-Axis 3: 210 mm Traverse Y-Axis 1: 110 (+65/-45) mm Traverse Y-Axis 2: 110 (+45,/-65) mm Traverse Z-Axis 1: 300 mm Traverse Z-Axis 3: 300 mm Traverse Z-Axis 2: 810 mm Traverse B-Axis: 870 mm turning speed range - spindle: 5.000 1/min Number of spindle speed ranges: 2 . spindle nose: JIS A2-6 spindle bore: 73 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° turning speed range - spindle: 5.000 1/min spindle nose: JIS A2-6 spindle bore: 73 mm bar material dia. max: 65/52 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° Number of Turrets: 3 . Number of tool stations: 16 x 3=48 pos Schank height for square tool: 20 mm Diameter of boring bar: 32 mm turret changing time (4-stations): 0,18 sec Number of driven tools: 16 x 3=48 pos max. spindle speed driven tools: 6.000 U/min. Rotary tool machining ability: M16 / Ø16 . rapid traverse X-axis: 30 m/min rapid traverse Y-axis: 20 m/min rapid traverse Z-axis: 50 m/min drive capacity - spindle motor: 25 / 22 kW power capacity - driven tools: 7,5 / 5,5 kW total power requirement: 92,7 kVA weight of the machine ca.: 9,4 t dimensions of the machine ca.: 4,0 x 2,8 x 2,4 m Accerories Chip conveyor Coolantsystem C-axis in main and sub spindle Y-axis 2 x part counter total counter tool setting Overhead partsgripper with conveyor belt. Spindle 1 Chuck SMW KNCS-N 210 / 52 mm Spindle 2 Collet Chuck Hainbuch Spanntop nova Kombi Axfix 65 Robot interface CNC Turning- and Milling Center MORI SEIKI NZ 2000 T3Y2 The NZ2000 T3Y has 2 spindles and 3 turrets, and 2 turrets have the Y-axis function and built-in milling motors. This not only allows synchronized machining using 3 turrets, but also achieves heavy-duty cutting and high-speed machining using rotary tools thanks to the built-in motor turrets. *

Condition: ready for operation (used), Year of construction: 2008, travel distance X-axis: 210 mm, travel distance Y-axis: 110 mm, travel distance Z-axis: 810 mm, overall weight: 9,500 kg, number of axes: 6, This 6-axis DMG Mori Seiki NZ2000T3Y2 was manufactured in 2008. It features a maximum machining diameter of 200 mm and a maximum machining length of 260 mm. The bar machining capacity is 65 mm, with an X-axis travel of 210 mm, Z-axis travel of 810 mm, and Y-axis travel of 110 mm. If you are looking to get high-quality turning capabilities, consider the DMG Mori Seiki NZ2000T3Y2 machine we have for sale. Contact us for further details. • Max. machining diameter: φ200 mm • Max. machining length: 260 mm • Bar machining capacity: φ65 mm • Phase: 3 • Frequency: 50 Hz • Voltage: AC 200 V • Full load current: 283 A • Spindle motor current rating: 105 A Nodpfey Tvdfex Ad Sswh • Short circuit current: 1 kA • Maximum voltage: 220 V • Rated power: 98 kVA Technical Specification Counter Spindle Yes Driven Tools Yes

Condition: used, Year of construction: 2005, machine/vehicle number: ZT151AEG0163, CNC control MORI SEIKI MSX-501, 2 turrets each with 16 tool stations, driven tools, 2 spindles, bar capacity 52 mm, max. speed 6,000 rpm, max. turning diameter 190 mm, max. turning length 450 mm, Y-axis +/- 40 mm, machine weight 5,100 kg, chip conveyor Nwedpfxoy Sqhpe Ad Seh

Condition: excellent (used), Year of construction: 2007, CNC Control: MSX-501III X axis mm: 730 Y axis mm: 730 Z axis mm: 850 B axis mm: 0.001 Pallet size mm: 500 x 500 Number of pallets: 2 Table load capacity kg: 500 Cutting feed mm/min X, Y, Z: 50,000 Max. rapid traverse m/min X, Y, Z: 50, 50, 50 Spindle speed rpm: 14,000 Spindle power kW: 22/18.5 Taper type: BT-40 Torque Nm: - Tool changer type: Chain Njdpeythprofx Ad Sswh Tool magazine positions: 60 Max. tool diameter mm: 70 Max. tool diameter with adjacent pockets empty: 140 Max. tool length mm: 500 Max. tool weight kg: 8 Coolant tank capacity l: 760 Through-spindle coolant bar: Yes Equipment Chip conveyor Internal coolant Rigid tapping Manuals, electrical diagrams, etc.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, CNC Control: F31iA X axis travel mm: 560 Nwsdpfx Adjyhlqpe Seh Y axis travel mm: 560 Z axis travel mm: 630 B axis travel: 360.000° Table load capacity: 400 kg Cutting feed rate X/Y/Z mm/min: 50,000 Maximum rapid traverse X/Y/Z m/min: 50 Spindle speed rpm: 14,000 Spindle power kW: 18.5 Taper type: BT-40 Torque Nm: 120 Magazine type Magazine positions: 60 Maximum tool diameter mm: 70 Maximum tool diameter with adjacent positions empty mm: 140 Maximum tool length mm: 400 Maximum tool weight kg: 8 Coolant tank capacity l: 500 Through spindle coolant pressure bar: 70 EQUIPMENT Chip conveyor Through spindle coolant with high-pressure pump, 70 bar Tool breakage detection probe Renishaw spindle measuring system Extended tool offsets: up to 400 offsets Additional coordinate systems: 48 Workpiece coordinate systems Tool life management Extended program memory: Total length 1,280 m (512KB) Up to 1,000 storable programs Preparation for NH4000 8CPP + 8 Pallets

Condition: excellent (used), Year of construction: 2011, CNC Control: FANUC Series 31i-A5 X axis travel mm: 730 Y axis travel mm: 510 Z axis travel mm: 510 B axis (degrees): +160 / -180 C axis (degrees): 360 Number of pallets: 1 Table size mm: Ø500 Table load capacity kg: 300 Cutting feedrate mm/min (X, Y, Z): 50,000, 50,000, 40,000 Maximum rapid traverse m/min (X, Y, Z): 50, 50, 40 Spindle speed rpm: 12,000 Spindle power kW: 18.5 / 15 Taper type: BT-40 Torque Nm: - Tool changer type: Chain Tool magazine capacity: 61 Max. tool diameter mm: 90 Max. tool diameter with adjacent positions empty: 125 Max. tool length mm: 300 Max. tool weight kg: 8 Coolant tank capacity l: 750 Through-spindle coolant (bar): Yes EQUIPMENT Rotary table with digital readouts: Included Work light: Included Through-spindle coolant Electronic handwheel integrated in CNC panel Coolant oil skimmer Tool life management 3D tool compensation Cylindrical interpolation MORI-APM programming software MACHINE DIMENSIONS Length mm: 2,771 Width mm: 3,948 Height mm: 3,264 Nodpfjydh Hlox Ad Sswh Weight kg: 12,400

Condition: excellent (used), Year of construction: 2011, TECHNICAL DETAILS CNC control: MSX-501III X axis mm: 560 Y axis mm: 560 Z axis mm: 660 B axis deg.: 360.000 Table load capacity kg: 400 Cutting feed rate mm/min X,Y,Z: 60,000 Max. rapid traverse m/min X,Y,Z: 50 Spindle speed rpm: 12,000 Spindle power kW: 15 Taper type: ISO-40 Torque Nm: 120 Tool changer type: Chain Tool changer positions: 60 Max. tool diameter mm: 70 Max. tool diameter with adjacent positions empty mm: 170 Max. tool length mm: 450 Max. tool weight kg: 8 Coolant tank capacity l: 500 Through-spindle coolant (high-pressure): Yes EQUIPMENT Double chip conveyor ISO-40 taper High-pressure through-spindle coolant with pump Nwodpsxfka Njfx Ad Seh Tool breakage detection probe Part measuring probe RENISHAW MACHINE DIMENSIONS Length mm: 3,755 Width mm: 2,300 Height mm: 2,610 Weight kg: 7,600

Condition: like new (used), Year of construction: 2016, operating hours: 7,595 h, functionality: fully functional, turning length: 1,260 mm, turning diameter: 420 mm, spindle speed (max.): 3,000 rpm, travel distance X-axis: 280 mm, travel distance Y-axis: 60 mm, travel distance Z-axis: 1,370 mm, bar diameter (max.): 90 mm, spindle nose: IS A2-8, spindle diameter: 91 mm, Equipment: documentation/manual, CNC controller: Mitsubishi M730UM Capacity X-axis travel mm: 280 Y-axis travel mm: ±60 Z-axis travel mm: 1370 Turning length mm: 1260 Max. turning diameter mm: ø 420 Swing over bed mm: ø 978 Swing over cross-slide mm: 808 Bar work capacity mm: 90 Upper turret Number of tool slots St .: 12 Speed ​​driven tools RPM: 10000 Main spindle Speed ​​spindle rpm: 3000 Drive power spindle kW: 22/18.5 Spindle bore mm: 91 Chuck type: 15" Nwodezgu Dujpfx Ad Soh Manufacturer: KITAGAWA Spindle nose: IS A2-8 Tailstock Tailstock travel mm: 1284 Holder: MT-5 Coolant system High-pressure bar: 10 Equipment Chip conveyor blowing air through spindle center selectable via M-function Tool measuring arm Mist collector Steady rest Workarea light Chuck foot switch (double) for main and counter spindle Oil skimmer Custom Macro common variables (200) Basic machine dimensions / weight Length mm: 5300 Width mm: 2500 Height mm: 2400 Weight kg: 8900

Condition: excellent (used), Year of construction: 2015, DMG MORI NLX 2500 MC/700 lathe Nwsdpfjzgkdkjx Ad Seh Year: 2015 M730M control system with CELOS-ERGOline Parts catcher Measuring probe Chip conveyor 5 driven tool holders 2 ER32 axial tool holders 2 ER32 radial tool holders 1 end mill holder Very good condition, low operating hours.

Condition: used, Year of construction: 2005, machine/vehicle number: IntNr231574, Machine Specifications Control: MORI SEIKI MSX-850 Design: Slant-bed turning center Version: SY with Y-axis Turret: 12-position with driven tools Working Area Max. turning diameter: 356 mm Nwedpfx Aszgghfed Seh Standard turning diameter: 275 mm Max. turning length: 705 mm Traverse Travels X-axis: 260 mm Y-axis: ±50 mm / total approx. 100 mm Z-axis: approx. 795 mm Rapid traverse X/Y/Z: 30 m/min Counter spindle LNS Quick Load Servo 2 bar feeder Max. bar length: approx. 1,500–1,600 mm / 63" The machine can be inspected under power by appointment. Specifications and technical details are subject to change and error. Prior sale reserved.

Condition: used, Year of construction: 2006, machine/vehicle number: IntNr231573, A used MORI SEIKI NL 2500/1250 CNC lathe, year of manufacture 2006, is available for sale. The machine is equipped with a MORI SEIKI MSX 850III / MAPPS III control system and an IRCO SIMAG bar feeder for automatic bar loading. Technical data Control: MORI SEIKI MSX 850III / MAPPS III Origin: Japan Design: Slant-bed CNC lathe Centre distance: 1,250 mm Maximum turning length: 1,298 mm Maximum turning diameter: 356 mm Standard turning diameter: 275 mm Nwsdpfozggg Uox Ad Soh Swing diameter over bed: 923 mm X-axis travel: 260 mm Z-axis travel: 1,345 mm Spindle speed: up to 4,000 rpm Spindle bore: approx. 80 mm Turret: 12 stations Number of turrets: 1 Chip conveyor Driven tools C-axis Y-axis Machine weight: 7,600 kg Machine dimensions (L x W x H): 5,000 x 2,300 x 2,400 mm The machine can be inspected under power by prior appointment. Technical data and specifications subject to change and error. Sale subject to prior sale.

Condition: good (used), Year of construction: 1990, CNC machining center Manufacturer: MORI SEIKI Type: Partner M300 A-1 Year of manufacture: 1990 Control: FANUC O-M Travel ranges: X/Y/Z: 400 x 300 x 495 mm Distance between spindle center and pallet table (Y-axis): 25 – 325 mm Distance between spindle nose and pallet table (Z-axis): 125 – 620 mm Rapid traverse: 24 m/min Feed rate up to 5 m/min Spindle: Ball screw: 36 mm diameter Feed drives FANUC AC X/Y-axis model 5, Z-axis model 10 Main spindle speed: 100 – 6000 rpm Main spindle motor: AC 5.5 kW Main spindle taper: BT 40 Pallet: Pallet size: 315 x 315 mm Pallet indexing angle: 7.5 degrees Indexing accuracy: + / - 2 sec. Repeatability accuracy: + / - 1 sec. Pallet clamping force: 3,400 kg Workpiece weight max.: 150 kg Automatic tool changer: Number of tools: 30 Nwodpfx Aet Rg E Sjd Seh Tool change time: 2.5 sec. Collet clamping time: 7 sec. Tool diameter max.: 110 mm Tool length max.: 250 mm Tool weight max.: 8 kg Special accessories: End-of-work indicator with alarm light Magazine for 30 tools Operating hour display Tool life monitoring Coolant system Work area lighting Weight: approx. 4,500 kg Footprint: 1,900 x 2,300 mm 23626

Condition: ready for operation (used), Year of construction: 2010, operating hours: 5,002 h, functionality: fully functional, machine/vehicle number: NT100JG0126, turning length: 424 mm, turning diameter: 370 mm, travel distance X-axis: 380 mm, bar passage: 52 mm, controller model: FANUC FS-31iA5 (MAPPS 4), TECHNICAL DETAILS Turning length: 424 mm Maximum turning diameter: 370 mm (270 mm with turret 2) Bar capacity: 52 mm Turning-milling spindle Full indexing capabilities: Yes X-axis travel: 380 mm Y-axis travel: ± 105 mm Z-axis travel: 460 + 155 mm (ATC) B-axis: ± 120º Spindle speed: 12,000 rpm Drive power: 9/5.5 kW Tool magazine Number of magazine positions: 38 Tool holder: Capto C5 Maximum tool length: 250 mm (210 mm for tools under Ø70 mm) Maximum tool diameter: 70 mm / Ø130 mm (with/without adjacent tools) Maximum tool weight: 5 kg Lower turret X-axis travel: 155 mm Z-axis travel: 610 mm Nwjdpjzf H Ezsfx Ad Soh Number of tool slots: 10 Tool speed: 6,000 rpm Drive power for driven tools: 1.5/1.2 kW Main spindle Spindle speed: 6,000 rpm Drive power: 11/7.5 kW Spindle bore: 73 mm Chuck type: Hollow chuck (8") Manufacturer: KITAGAWA Spindle nose: JIS A2-5 Maximum torque: 223 Nm Counter spindle Spindle speed: 1,000 rpm B-axis: 4 fixed positions, 0º, -30º, -180º (-225º for overhang onto conveyor, if available) MACHINE DETAILS Control: FANUC FS-31iA5 (MAPPS 4) Potential rated power: 39.24 kVA Dimensions & Weight Dimensions (L x W x H): 2,705 x 2,425 x 2,385 mm Weight: 8,800 kg Operating Hours Power on: 54,061 h Spindle 1 operating hours: 9,813 h Spindle 2 operating hours: 5,002 h EQUIPMENT Chip conveyor Signal lamp High-pressure pump Air blow nozzle outside the spindle Foot switch (dual) for main and counter spindle

Condition: good (used), Year of construction: 1997, functionality: fully functional, travel distance X-axis: 510 mm, travel distance Y-axis: 510 mm, travel distance Z-axis: 510 mm, CNC control MSC 803 25-fold automatic tool changer coolant device Nodpfx Ajwhkcxed Sewh Technische Daten / technical details: Verfahrweg X / X-Travel 510 mm Verfahrweg Y / Y-Travel 510 mm Verfahrweg Z / Z-Travel 510 mm Tischgröße / table size 750x550 mm Drehzahlbereich / spindle speed 8000 UpM /rpm Anzahl der Werkzeugplätze / tool places in changer 25 fach Spindelaufnahme / spindle taper BT40 Gewicht der Maschine ca. / weight 4500 Kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: used, Year of construction: 1996, operating hours: 48,257 h, functionality: fully functional, machine/vehicle number: 299, Mori Seiki SL150 & Iemca short bar feeder. The machine is fully functional. 12-Station Turret with Tool Holders MSC-518 (Fanuc ) CNC Control 8″ Hydraulic Chuck 2 Step gear spindle for powerful torque Hydraulic Tailstock with Power Quill Chip Conveyor Nwodezg A Saepfx Ad Soh Coolant System. Automatic Lubrication system Parts catcher

Condition: used, Year of construction: 1995, turning diameter 450 mm turning length 1.125 mm control FANUC MSC 518 turning diameter over bed 520 mm bar material dia. 70 mm x-axis 260 mm z-axis 500 mm spindle tunring speed 30 - 3.000 U/min spindle nose JIS A2-8 spindle bore 80 mm spindle bearing diameter 130 mm Number of tools in turret 12 rapid travel - longitudinal/face 15 m/min power capacity 15/11 kW total power requirement 42 kW weight of the machine ca. 5 t dimensions of the machine ca. 3,6 x 1,7 x 1,8 m In our assessment, the machine is in good used condition and can be inspected under power by appointment. Technical Features & Accessories: - LG 10 portal loading system with workpiece stacking device up to D=200 and max. 10 kg - Kitagawa 250 mm power chuck - Hollow clamping device - Chip conveyor - High-pressure cooling 5 bar - Tailstock Nwjdpfexr Rbyjx Ad Soh Accessories, tools, and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and specifications, as well as prior sale!

Condition: good (used), Year of construction: 2010, operating hours: 5,750 h, functionality: fully functional, turning length: 393 mm, turning diameter: 200 mm, spindle bore: 51 mm, MSX 853 cnc control 3-jaw chuck diameter 210mm 12-fold revolver C-axis driven tools tail stock coolant device chip conveyor Technische Daten: / technical details Drehdurchmesser / turning diameter 200 mm Drehlänge / turning lenght 393 mm X-Weg / X-travel 160 mm Z-Weg / Z-travel 450 mm Njdpfx Aezd S S Rod Sewh max. Drehzahl Spindel / max. spindle speed 50-3000 UpM /rpm Eilgang X/Z / rapid feed X/Z 24/30 Anzahl der Revolverplätze / number of tool places 12 max. Stangendurchmesser / max. bar diameter 51 mm Antriebsleistung Spindel / drive capacity spindle 13,5 kW Gewicht ca. / weight ca. 3500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: used, Year of construction: 2008, Technical details: standard turning dia.: 200 turning length: max. 810 mm control: MSX-701 MAPPS III greates pass round over bed: 800 mm Max. distance between centres: 1130 mm max. turning diameter: 320 mm max. workpiecediameter: 300 mm bar material dia.: 65 mm Traverse X-Axis 1: 210 Traverse X-Axis 2: 210 mm Traverse X-Axis 3: 210 mm Traverse Y-Axis 1: 110 (+65/-45) mm Traverse Y-Axis 2: 110 (+45,/-65) mm Traverse Z-Axis 1: 300 mm Traverse Z-Axis 3: 300 mm Traverse Z-Axis 2: 810 mm Traverse B-Axis: 870 mm turning speed range - spindle: 5.000 1/min Number of spindle speed ranges: 2 . spindle nose: JIS A2-6 spindle bore: 73 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° turning speed range - spindle: 5.000 1/min spindle nose: JIS A2-6 spindle bore: 73 mm bar material dia. max: 65/52 mm spindle bearing diameter: 120 mm C-Axis: 0,001 ° Number of Turrets: 3 . Number of tool stations: 16 x 3=48 pos Schank height for square tool: 20 mm Diameter of boring bar: 32 mm turret changing time (4-stations): 0,18 sec Number of driven tools: 16 x 3=48 pos max. spindle speed driven tools: 6.000 U/min. Rotary tool machining ability: M16 / Ø16 . rapid traverse X-axis: 30 m/min rapid traverse Y-axis: 20 m/min rapid traverse Z-axis: 50 m/min drive capacity - spindle motor: 25 / 22 kW power capacity - driven tools: 7,5 / 5,5 kW total power requirement: 92,7 kVA weight of the machine ca.: 9,4 t dimensions of the machine ca.: 4,0 x 2,8 x 2,4 m Accerories Chip conveyor Coolantsystem C-axis in main and sub spindle Y-axis 2 x part counter total counter tool setting Overhead partsgripper with conveyor belt. Spindle 1 Chuck SMW KNCS-N 210 / 52 mm Spindle 2 Collet Chuck Hainbuch Spanntop nova Kombi Axfix 65 Robot interface Lehmann Robot with parts belt for feeding and disposal Nwodpfezd Su Eex Ad Seh CNC Turning- and Milling Center MORI SEIKI NZ 2000 T3Y2 The NZ2000 T3Y has 2 spindles and 3 turrets, and 2 turrets have the Y-axis function and built-in milling motors. This not only allows synchronized machining using 3 turrets, but also achieves heavy-duty cutting and high-speed machining using rotary tools thanks to the built-in motor turrets. For shaft parts loading and unloading there is a Lehmann Robot with conveyor belts for loading and unloading. The machine can also be sold without robot. *

Condition: used, Year of construction: 1998, functionality: fully functional, Equipment: documentation/manual, rotational speed infinitely variable, Mori Seiki lathe 2 axes (X, Z) Model: SL-300B Year: 1998 CNC: Fanuc MSC-501 3-phase power Nedpfjzd R Ikex Ad Sswh Chip conveyor Documentation

Condition: used, TECHNICAL DETAILS - Number of spindles : 2 - Number of turrets : 1 - Number of axes : 6 MAIN SPINDLE - Spindle nose : A2-8 - Max. bar diameter : 80 [mm] - Spindle power : 18,5 [kW] - Spindle speeds : 4.000 [rpm] - Max. turning diameter : 460 [mm] - C axis indexing precision : 0,001 [°] TURRET - Number of positions : 12 - Number of motorized positions : 12 - X/Z stroke : 260 x 795 [mm] - Y stroke : +/- 50 [mm] - Live tools speed : 6.000 [rpm] - Live tools power : 5,5 [kW] COUNTER-SPINDLE - Spindle nose : A2-5 - Max. bar diameter : 51 [mm] - Max. turning diameter : 190 [mm] - Spindle power : 11 [kW] - Spindle speeds : 6.000 [rpm] - C axis indexing precision : 0,001 [°] - Travel : 760 [mm] POWER SUPPLY - Supply voltage : 200 [V] - Total installed power : 42 [kVA] WEIGHT & DIMENSIONS - Machine floor space : 4.414 x 2.370 [mm] - Machine height : 2.115 [mm] - Machine weight : 6.200 [kg] MACHINE HOURS - Number of hours under power : 15525 [h] - Number of working hours : 12865 [h] EQUIPMENT - CNC : Mitsubishi MSX-850II - Interactive programming : MAPPS III - Interface : USB / PCMCIA / RJ45 - Tool probe : Renishaw - 3 colors status lamp - Tailstock function - Coolant tank - Chips conveyor : Droite - Spindle cooling unit - Parts catcher - Bar loader : LNS Quick LoadSERVO 80 - Parts conveying strip - Number of turning tool holders : 2 Nwodpfox Tvkrjx Ad Seh - Number of fixed tool holders : 10 - Chuck 3 jaws

Condition: used, TECHNICAL DETAILS - Number of axes : 4 - Number of spindles : 1 - Number of turrets : 1 MAIN SPINDLE - Spindle nose : A2-8 - Spindle power : 18,5 [kW] - Spindle speeds : 4.000 [rpm] - Max. bar diameter : 80 [mm] - Max. machining length : 728 [mm] - Max. turning diameter : 460 [mm] - C axis indexing precision : 0,001 [°] TURRET - Number of positions : 12 - Number of motorized positions : 12 - X/Z stroke : 260/795 [mm] - Y stroke : +/- 50 [mm] - Tool type : BMT - Live tools speed : 10000 [rpm] TAILSTOCK - Tailstock type : Numérique - Type of cone : CM5 - Tailstock stroke : 650 [mm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 39 [kVA] WEIGHT & DIMENSIONS - Machine floor space : 3.110 x 1.922 [mm] - Machine height : 2.120 [mm] Njdpfx Adsx Tvklj Sjwh - Machine weight : 6.100 [kg] MACHINE HOURS - Number of hours under power : 26654 [h] - Number of working hours : 15488 [h] EQUIPMENT - CNC : CELOS - Interactive programming : MAPPS 4 - Interface : USB, PCMCIA, RJ45, RS232 - Tool probe : Renishaw - Coolant tank * with high-pressure pump : 15 [bars] - Chips conveyor - Tool probe - Parts catcher - Parts conveying strip - Bar loader : LNS QUICK LOAD SERVO 80 S2 - Number of fixed tool holders : 9 - Number of turning tool holders : 3 - Electric transformer - Collet chuck

Condition: used, TECHNICAL DETAILS - Number of axes : 4 MAIN SPINDLE - Spindle nose : A2-8 - Spindle power : 18,5 [kW] - Spindle speeds : 4000 [rpm] - Max. bar diameter : 80 [mm] - Max. turning diameter : 366 [mm] - C axis indexing precision : 0.001 [°] TURRET - Number of positions : 12 - Number of motorized positions : 12 - X/Z stroke : 280 x 785 [mm] - Y stroke : +/- 50 [mm] - Live tools speed : 6000 [rpm] * Live tools power : 5,5 [kW] TAILSTOCK - Tailstock type : Numérique - Type of cone : CM5 - Distance between centers : 705 [mm] POWER SUPPLY - Supply voltage : 400 [V] - Total installed power : 39 [kVA] Nwodpfx Asyxr U Red Sjh MACHINE HOURS - Number of working hours : 7261 [h] WEIGHT & DIMENSIONS - Machine floor space : 3800 x 2143 [mm] - Machine height : 2232 [mm] - Machine weight : 6100 [kg] EQUIPMENT - CNC : MORI MSX-850 III (Mitsubishi 720BM) - Tool probe - 3 colors status lamp - Coolant tank - Chips conveyor - Chuck 3 jaws : hydraulique - Number of turning tool holders : 3