Used Metal Stamping Press for sale (54,713)

Condition: used, Workshop-refurbished Single-Column Eccentric Press WEINGARTEN Type AV 40 Machine No. 121826 D, Year of manufacture 1976 – Completely overhauled in 2003 Pressing force: 40 tons Throat depth: 225 mm Table opening: Ø 200 mm with support rim Ø 225 mm Table dimensions: 560 x 470 mm Ram area: 260 x 200 mm Adjustable ram stroke: 8–88 mm Ram adjustment: 63 mm Max. install height: 500 mm Clamping shank bore: Ø 40 mm Hfedpfx Ajxlkq Ish Nsb Strokes per minute: 40–120 Motor power: 4 kW Power supply: 400 Volt, 50 Hz Table height above floor: 700–950 mm - Table height adjustment with 2 support spindles - Drop-through hole in table as round table opening with reduction ring from Ø 225 to Ø 100 mm - Clutch-brake combination via WEINGARTEN friction-threaded clutch with TDC run-through protection - Stroke release via electric footswitch or two-hand control console - Front crankshaft support bearing - Overload protection via shear plate - Manual central lubrication - Electrical cabinet with dual-circuit contactor control from 2003, permanently mounted on the machine - Safety standard (UVV) for manual loading/unloading The machine is equipped with the following operating modes: - Setup - Single stroke (two-hand) - Single stroke (foot) - Continuous run (foot) - Automatic continuous run - External engagement Required space (L x W x H): 1900 x 950 x 2600 mm Weight: 3.1 tons Very good condition

Condition: excellent (used), Year of construction: 2015, operating hours: 5,100 h, Power: 4,000 kN Bolster area: 3,000 x 1,400 mm (W x D) Clamping surface table: 2.950 x 1.500mm Clamping surface ram: 2,950 x 1,240 mm Daylight: 600 mm (stroke down and adjustment on top) Frequency: 5 - 100 rpm, infinitely variable Stroke: 20 - 200 mm, automatically adjustable Ram adjustment: 150 mm (motorized) Design: - With servo technology, speed of ram adjustable, possible to pendle - Table - clamping plates divided and manually adjustable - 8-fold sliding guide - motorized oil - central lubrication - automatic ram adjustment - pneumatic ram weight compensation - electromotive stroke adjustment - control Siemens + Fanuc - visualization Siemens Panel PC in mobile desk - tool safety device 8-fold - tool data memory - 2-channel press force measurement - Hydraulic overload protection - T-slots in table and ram Hfjdpfspvlf Sox Ah Nob - Longitudinal groove for tool centering in ram - Anti vibration machine feet - opening in the table Equipped with a complete decoiling line make Lorenz Decoiler Load capacity: 80kN strip width: 20 - 820 mm Inner diameter: 470 - 520 mm Coil - outer diameter 1.800 mm Straightening machine strip width: max. 820 mm Strip thickness: 0,5 - 4,0 mm Straightenable cross section: 1.600mm² Number of rolls: 9 pcs, Ø 65 mm + 2 pcs feeding rolls Speed: 0 - 30 m/min Electronic roll feed Strip width: max. 820 mm Strip thickness: 0.5 - max. 6.0 mm Cross section: max. 2.400 mm² Number of rollers: 2 pcs. Ø 120 mm

Condition: refurbished (used), Year of construction: 1992, machine/vehicle number: 131 644, Attention: machine has been 2022 completely mechanically and electrically retrofitted before delivery press force: 1000kN Hfodpfxofn Affj Ah Nsb stroke: 30 - 100mm slide adjustment: 80mm speed: 50 - 300/min shut height. 350mm table dimensions: 1080 x 800mm slide dimensions: 900 x 620mm new electrical controller SIEMENS S7 1500

Condition: new, Year of construction: 2025, functionality: fully functional, Specialised press built from the ground up for briquetting of iron, steel and similar alloys. Includes integrated oil collection pads. Does not include packing table – only briquette guides (slides). Comes with see through bunker doors & oil heating elements as standard. Machines are controlled by Siemens KTP-400 touchscreens. 2nd generation available for purchase from February 2024. For this press please first contact us! Technical Data : Throughput: Up to 600 briq/h* Main motor: 30kW Infeed motors: 2.6kW Cooling system: 1.6kW Hodpfx Ajtmugcsh Nefb Total power: 34.2kW Oil tank: 260l Filters: 4 Length: 2000mm Width: 2000mm Height: 2200mm Weight: 3500kg Briquette size: 40-110, D80mm Warranty: 2 years / 2 000 workhours

Condition: used, Antike Kniehebelprägepresse / Antique Embossing Hot Stamping Press Karl Krause KHP Baujahr / Year ca. 1930 - Serial-No. 48090 Hfjdpjwtw E Djfx Ah Njb Prägefläche / Embossing Size max. 340 x 430mm Beheizung mit Gas / Heating with Gas Online-Video-Inspection by WhatsApp - MS Zoom - Telegram On Stock Emskirchen/Nürnberg - Available Immediately - Can be test

Condition: ready for operation (used), With hydraulic pump. Hfsdpfohw E D Sex Ah Nsb

Condition: used, Swivel bending machine FASTI Type 2095-25-2,5 Serial no. 94 295 004 Year of construction 1994 effective length 2540 mm max. sheet thickness 2.5 mm Stroke of upper beam 380 mm Motor power bending beam 2.2 kW Mains connection 400 Volt, 50 Hz Hfedpottc Uajfx Ah Nob - NC control FASTImatic FM100 - One-piece 135° pointed rail - Controlled backgauge - Continuous stop rail - controlled bending angle via control unit - electric foot switch weight 3000 kg good condition

Year of construction: 1994, condition: good (used), machine/vehicle number: 25286, Built in 1994 Equipment: embossing press: • case magazine with case bending device DBA (without feeding conveyor) • foil feeder with two pairs of foil feeding rollers • electric counter Hsdpfx Ajd R Saqjh Njfb • delivery conveyor to the right

Condition: good (used), Year of construction: 1976, Pressing force: 20 t Stroke rate: max. 150 rpm, adjustable via PIV gearbox from the control panel Stroke, adjustable: 10 - 50 mm Installation height: 270 mm (maximum stroke at top, without wedge plate) Ram reinforcement: 50 mm Table area: 340 x 320 mm (W x D) Pass-through opening: 70 x 180 mm (W x D) Hfjdpfxewufrze Ah Neb Ram area: 160 x 230 mm (W x D) with wedge plate Drive power: 2 HP Features: - 1 connecting rod - Double V-ram guide - Motorized oil lubrication - Manual ram adjustment, 50 mm - Mounting bracket for feed unit, tiltable - 3 cams for feed unit etc. - Free-standing control panel - Forward and reverse operation - Manual setup using a rod

Condition: new, Year of construction: 2025, Are you looking for quality and expertise for your sheet metal processing machine? Then we are the right partner at your side. Folding bench ZGR-2140/0.8 Maximum working length of press brake: 2140 mm Bending performance: up to 0.8 mm (steel sheet) Titanium Zinc Sheet: 0.8mm Aluminum Sheet: 1.2mm Copper Sheet: 1.25mm Bending machine bending angle: 145 degrees max Cut with the roller shears over the entire working width Bending beam thickness: 15 mm Cut with the roller shears over the entire working width Lifting of the upper beam in three positions Upper beam stroke: 80 mm degree scale Weight of the folding bench: approx. 180 kg Roller scissors plus 350 euros Manual folding machine plus 75 euros Delivery costs: PLEASE ASK Price: 1050 euros Delivery date: every week Cash on delivery and bank transfer in advance Hfodeci Hlfepfx Ah Nob We are looking forward to your contact!

Condition: used, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Hedpevi Hh Iofx Ah Nofb Online-Video-Inspection...

Condition: used, Single-column eccentric press WEINGARTEN type ER 63 Machine. No. 52A / 63 Year of construction 1963 Pressure capacity 63 ton. throat 280 mm Table surface 630 x 530 mm ram stroke adjustable 8-100 mm ram adjustment 63 mm Stroke rate 65 strokes / min. Motor power 4 kW Mains connection 380 Volt, 50 Hz - Clutch/brake combination with WEINGARTEN friction threaded clutch Hedolb I Dzspfx Ah Njfb - Electric lift release via foot switch - Wheel reduction gear - Overload protection by breaker plate - Front crankshaft support bearing Space requirement L x W x H 1500 x 1100 x 2500 mm Weight 4.5 tons good condition

Condition: reconditioned (used), Year of construction: 1983, Power: 2.000 kN Hfjdpogpxc Sefx Ah Njb Frequency: 60 rpm Stroke, adjustable: 20 - 120 mm Daylight: 450mm (max. stroke up) Ram adjustement: 100mm Size of bolster: 850 x 810mm Opening in bolster: 00 x 50mm Ram area: 750 x 810mm Motor power: 22 kW equipped by: - 1pc. con rod - 6pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - manuel stroke adjustment - pneumatic ram balancing cylinder - anti vibration machine feet

Condition: used, Prägepresse / Hot Foil Stamping Press Online-Video-Inspection by Skype-Video Hfjdpfst Drnxjx Ah Njb We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Single-column eccentric press WEINGARTEN type ARP 100 Machine no. No. 122481 Year of construction 1984 Pressure capacity 100 ton. Hjdpfxju Rwa Is Ah Nsfb throat 400 mm Table size 920 x 660 mm ram surface 700 x 450 mm Rear upright width 735 mm Stroke adjustment 20 - 160 mm Plunger adjustment 80 mm Installation height with 160 mm stroke max. 355 mm (without intermediate table top) Installation height with 20 mm stroke max. 425 mm (without intermediate table plate) Stroke rate 60 strokes/min. Table surface intermediate table top 920 x 610 mm Thickness of intermediate table top 90 mm Hole in intermediate table top Ø 210 / 180 mm Through-hole in machine table Ø 210 / 180 mm Table height above floor 800 mm (without intermediate table top) T-slot width in table and ram 22 mm Clamping pin bore 50 mm Motor power 11 kW Mains connection 400 Volt, 50 Hz - Hydraulic overload protection in ram - ORTLINGHAUS pneumatic clutch/brake combination - Electromotive ram adjustment with counter - Clamping pin bore with clamping piece - Front crankshaft support bearing - Gear reduction gears in closed oil bath gearbox - Two pneumatic tappet compensation cylinders - WOERNER automatic central grease lubrication - Lift release via electric foot switch or two-hand control panel - Electrical control cabinet permanently attached to the machine - Operating instructions and circuit diagram - UVV for manual insertion work Space requirement L x W x H 2200 x 1600 x 3250 mm Weight 8.3 tons Good condition

Condition: good (used), Year of construction: 1986, operating hours: 10,000 h, power: 30 to (US) , app. 270kN bolster area: 30" x 21" = 762 x 533mm ram-area: 800 x 300mm strokes/min: 100...1400 1/min stroke (fixed): 1" = 25,4mm ram adjustement: 1,75" = 44,5mm Hjdonl Snspfx Ah Nofb Equiped by * Hydraulic clutch * Roll feeder Make: Sankyo Type: Variax V70 Width: max. 100mm Only app. 10.000 working hours

Condition: used, machine/vehicle number: 24118, Kniehebelprägepresse - Embossing Stamping Press Krause KHP Prägefläche / Stamping size: 350 x 400 mm Sehr guter Zustand / Beautiful condition Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test Hfsdpfout Tkgjx Ah Nob

Condition: used, Eccentric punch press HAULICK + ROOS type RVD 125 double column - eccentric press Machine No. 212560 Year of construction 1981 pressure force 125 ton. table size 880 x 800 mm table opening 470 x 140 mm Hfedpfohlnzkex Ah Nob column width 900 mm column width lateral 415 mm ram stroke 45 mm slide adjustment travel 0-80 mm Installation height on the picture 340 mm Stroke rate 50 to 300 strokes/min. Motor power main drive 22 kW Mains connection 380 volt, 50 Hz - Double connecting rod drive with 4-fold eccentric shaft for off-center ram pressure load - adjacent electrical cabinet - NC roll feed EBU, width 250 mm, year 2003 - adjacent control panel for roll feed - strip running direction from left to right space requirement (press) L x W x H 3000 x 2000 x 3020 mm transport height 2950 mm weight of the press approx. 11 ton.

Condition: good (used), Year of construction: 1984, Power: 800 kN Frequency: 30 - 200 rpm, adjustable by PIV gearing Stroke, adjustable: 20 - 100 mm Daylight: 500mm (max. stroke up) Ram adjustement: 75mm Size of bolster: 1.010 x 800mm Opening in bolster: 700 x 150mm Ram area: 860 x 700mm Motor power: 22 kW equipped by: - 8pc. guideways - hydraulic overload - motorized oil lubrication - motorized ram adjustment - electro pneumatic stroke adjustment with complete decoiling line make ALBA, consisting of: Decoiler Outer diameter max. 1.400mm equipped by: • Decoiler moveable hydraulic • hydraulic coil loading device • hydraulic drive • hydraulic expansion 480 - 530mm • hydraulic pressure arm, lateral adjustable by handwheel • lateral arms Straightener Type: Ma Ria 9 Width: max. 400mm Thickness: 0,5 - 5,0mm Number of pulling rolls: 2 pc., Ø 120mm, upper can be lifted by hydraulic Number of straightening rolls: 9 pc., Ø 60mm, upper rollls adjustable by hydraulic drive, all rolls supported equipped by: • hydraulic strip insertion device • lateral strip guidings at entrance • lateral strip guidings at exit • basket at exit Hodpfx Aedhzf Ioh Njfb • loop control by sensor • lateral loop guiding Roll feeder Type: Vhy 400 Width: max. 400mm Thickness: max. 5,0mm passline adjustement by hydraulic jack We can offer even only press or decoiling line

Condition: used, machine/vehicle number: 21035, Heißpräge - Kniehebelprägepresse - Embossing Hot Stamping Press Krause FNPSerial-No. 4798 Stamping size: 550 x 400 mm Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Hsdjh Ayg Uopfx Ah Nofb Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Single-column eccentric press WEINGARTEN type E 40 Machine. No. 643/62 Year of construction 1963 Pressure capacity 40 ton. throat depth 250 mm Table opening 150 x 80 and Ø 200 mm Table surface 560 x 460 mm Hjdpfx Ahotx E Rqe Nsfb ram surface 250 x 200 mm Plunger stroke adjustable 8-88 mm Plunger adjustment 63 mm Installation height 320 mm Clamping pin bore Ø 40 mm Stroke rate 100/130 strokes / min. Motor power 2.2 / 3 kW Mains connection 400 Volt, 50 Hz Table height above floor 840 mm - Clutch/brake combination with WEINGARTEN friction threaded clutch with TDC run-through protection - Electric lift release via two-hand control - Overload protection by breaker plate - Manual central grease lubrication - Front crankshaft support bearing - Control cabinet adjacent - UVV for manual insertion work Space requirement L x W x H 1800 x 1500 x 2200 mm Weight 3.1 tons

Condition: used, machine/vehicle number: 18040, Kniehebelprägepresse - Embossing hot stamping press Hans Schilling HSMSerial-No. 18040 Online-Video-Inspection by Skype-Video We would be very pleased with your visit - more machines on Stock Hfjdpoh Axf Hefx Ah Nsb Available Immediately - Can be inspect On Stock Emskirchen / Nürnberg - Can be test

Condition: used, Hand - swing bending machine KRAMER type AMS 650 x 1,5 Hand swivel bending machine, press brake year of construction approx. 1985 working length 650 mm sheet thickness at 40 kg/mm2 1,5 mm upper beam opening approx. 60 mm bending beam adjustment ca- 0-25 mm Hfjdpfxsdzqaas Ah Njb bending angle 0-180 - Upper beam adjustment via hand crank - pre-screw rail for the bending beam - one-piece sharpening rail 135° space requirement L x W x H 1200 x 600 x 1100 mm weight 160 kg good condition

Condition: used, Single-column Eccentric Press MÜLLER GEFREES Type 60 SV DK (Identical to ExP60) Very lightly used eccentric press in original condition Machine No. 5250686 Year of manufacture: 1986 Nearly new condition Press force: 60 tons Throat depth: 280 mm Table surface: 740 x 560 mm Ram surface: 385 x 200 mm Through-hole in table: 300 x 200 mm Table surface (intermediate plate): 740 x 560 mm Through-hole in intermediate plate: Ø 103 mm Intermediate plate thickness: 70 mm Clamping pin bore: 40 mm Table height above floor: 815 mm (with intermediate plate) Installation height, max.: 275 mm (with intermediate plate) Hfodpfx Ahei A A Tbj Nob Installation height, max.: 345 mm (without intermediate plate) Stroke adjustment: 10–90 mm Ram adjustment: 60 mm Strokes per minute: 100 Motor power: 3 kW Drive: 380 Volt, 50 Hz - Mechanical rotary wedge clutch with pneumatic actuation - Spring-loaded single-jaw brake, controlled by cam disc - Stroke release via pneumatic footswitch - Overload protection with breaking plate in the ram - Table height adjustment via 2 threaded spindles - Manual central lubrication system by BEKA Schmiertechnik - Operating manual and pneumatic diagram included Space requirement (L x W x H): 1400 x 1100 x 2200 mm Weight: 3.4 tons In very good, almost new condition

Condition: used, Single-column eccentric press EBU Type 75 SKU Machine no. No. P 4598462 Year of construction 1962 Compressive force 75 ton. throat depth 300 mm Table surface 800 x 620 mm waste hole 325 x 225 mm Plunger surface 470 x 180 mm Clamping pin bore Ø 40 mm Table height above floor 845 mm Stroke adjustment 16 - 140 mm Plunger adjustment 80 mm Installation height max. approx. 420 mm Stroke rate 60 + 105 strokes/min. Motor power 4 kW Mains connection 380 Volt, 50 Hz. - Pneumatic clutch/brake combination EBU Hfjdsdzqltjpfx Ah Neb - Overload protection with breaker plate in ram - UNIDOR tool monitoring system, type APS MINI - mechanically driven gripper feed with belt straightener OSTERKAMP, type ZPN 200/350 - strip width: 200 mm, feed length: max. 350 mm - Strip thickness: max. 3 mm or approx. 200 x 1.5 mm - 2 speeds due to 2 V-belt stages on the wheel transmission - Two-handed operation - Simple work area shielding for swinging open - Table height adjustment in lowest position = threaded spindles for adjustment 50 mm below floor level - Control cabinet and control panel for tool monitoring adjacent - Automatic central lubrication - 4 machine feet Space requirement L x W x H 2600 x 2300 x 2450 mm Weight approx. 5.5 tons good condition