Used Maho 700 for sale (434)

Condition: ready for operation (used), Year of construction: 1989, Travel X/Y/Z: 700mm/500mm/600mm, speed: 6300rpm, power: approx. 10kW, feed X/Y/Z: 4m/min, rapid traverse X/Y/Z: 10m/8m/10m/min, machine dimensions X/Y/Z: approx. 4500mm/2300mm/2500mm, weight: approx. 6000kg, operating hours: 65425h. On-site inspection is possible. Tsdpfjwmqxkex Acneb

Year of construction: 1972, condition: ready for operation (used), Spindle-to-table distance min./max.: 81mm/481mm, counter support spindle center distance: 195mm, spindle head swivel: 360°, milling spindle diameter: 70mm, spindle adjustment: 100mm, headstock adjustment: 300mm, table dimensions X/Y: 480mm/820mm, travel X/Y/Z: 500mm/200mm/400mm, max. workpiece length: 400mm, spindle speed: 1600rpm, feed X/Y: 500mm/min, feed Z: 250mm/min, spindle head swivel: +/-30°, machine dimensions X/Y/Z: approx. 1600mm/2550mm/1700mm, weight: approx. 2300kg. The machine was electrically tested at the end of 2025 and a defect of the emergency stop switch was discovered. Documentation available. On-site inspection is possible. Tjdex S Rcmjpfx Acneb

Condition: used, Universal milling machine table, angle table, setup angle, clamping table, presumed MAHO make T-slot table, add-on table for universal tool milling machine Table no.: 76-400-1 / 2210 05 00 Table size: 700 x 330 mm Overall height: 210 mm T-slot width: 12 mm Todpoxy Stysfx Acnob T-slot pitch: 45 mm - Table plate with 7x T-slots, 12 mm each - Mounting surface 90°, 13 mm diameter holes, 14 mm elongated holes for fastening and 12 mm guide slot - Hole spacing, top mounting plate Ø 13 mm = 500 mm, 50 mm from the table surface (measured at center) - Hole spacing, middle mounting plate Ø 13 mm = 472 mm, 95 mm from the table surface (measured at center) - Elongated hole spacing, middle mounting plate = 475 mm, 140 mm from the table surface (measured at center) - Elongated hole spacing, bottom mounting plate = 475 mm, 185 mm from the table surface (measured at center) Dimensions (L x W x H): 820 x 330 x 210 mm Weight: 61 kg In good condition

Condition: used, NC universal tool milling machine MAHO type MH 700 P with HEIDENHAIN TNC 121 linear control . 71247 Circuit diagram no. ET 226 Built in 1979 Travel paths X: 600 mm, Y: 400 mm, Z: 400 mm Table size 900 x 500 mm Spindle mount ISO 40 Spindle speed 40-2000 rpm, 18 steps Feed rate X, Z-axis 1 - 600 mm/min, continuously variable Feed rate Y 1 - 300 mm/min, continuously variable Rapid traverse X, Z-axis 1.5 m/min Rapid traverse Y-axis 0.75 m/min Vertical spindle travel 80 mm Tsdewd Szbepfx Acneb Horizontal spindle travel 80 mm Spindle drive 4 kW Power supply 380 V, 50 Hz, 10 kW - HEIDENHAIN TNC 121 NC linear control - Vertical milling head with automatic Quill feed - Hydro-mechanical tool clamping - Coolant system in the machine base - Universal built-in rotary table, swiveling and tilting via threaded spindles +/- 30° - Universal built-in rotary table with manual transverse adjustment of 200 mm - Universal built-in rotary table with 360° rotation function and hydraulic clamping - Rotary table with direct indexing 72 x 5° and indirect indexing via hole plate 1:120 = 1 rev = 3° - Pivoting control panel - Central lubrication system - Electrical diagram Space requirement L x W x H 2000 x 1650 x 2250 mm Weight approx. 2800 kg Good condition

Condition: ready for operation (used), Maho milling table for Maho milling machine MH 700 S, milling table for interchangeable pallets 500x630 mm, used, normal signs of wear, 100% functional, scope of delivery as shown in photos. ATTENTION: Please enquire separately for costs of packing and shipping! Tsdpfx Acjx Dw Iwoneb

Condition: ready for operation (used), Maho milling head (Maho milling machine MH 700 S), used, normal signs of wear, 100% fully functional, scope of delivery as per photos. NOTE: Please enquire separately for costs of packing and shipping! Todjx Dw Iqepfx Acnob

Condition: used, Year of construction: 1987, Technical details: x-travel: 700 mm y-travel: 500 mm z-travel: 600 mm table swivelling +/-: A-Achse: 20° / 60° Grad table rotating: B-Achse: 360° Grad control: Maho 432 (3-D Bahnsteuerung) Max. Milling-capacity: ST: 60 und GG: 22 mm tool changer with: 24 Plätze number of spindle speeds: 20 - 6300 U/min. max. table load: 200 kg spindle taper MT: ISO 40 (hydr. Spannung) spindle head swivable left - right: 90° (manuell) ° quill stroke: 80 mm feed range: X/Z: 1 - 3000 und Y: 1 - 4000 und B: 0,1 - 3000°/min. mm/min rapid traverse:: X/Z: 10 und Y: 8 und B: 20 U/min. m/min control voltage: 110/220 V total power requirement: ca. 20 kVA Weight approx.: 5,5 t dimension machine xH: 3,0 x 2,4 x 2,25 m space requirements of the machine approx.: 5,2 x 5,0 x H: 2,3 m NC rotary table Ø 520 mm with A and B axes Adjustable three-phase motor with 4-stage reduction gear Working spindle can be swiveled out for horizontal spindle Equipment: -manual control unit -coolant device -machine ilumination Tedpfx Aou Idbyocnjb *

Condition: like new (used), Like-new tilting and swiveling rotary table Length: 800 mm Tsdpfx Ajy Ul D Rscneb Width: 300 mm

Year of construction: 1982, condition: good (used), machine/vehicle number: 75 810, table mounting size: 630 Ø mm movement x: 600 mm movement y: 450 mm movement z: 500 mm tailstock stroke: von Hand 80 mm Tsdoby Hhtopfx Acnjb spindle taper: ISO 40 spindle turning speed range: 20 - 3150 rpm carriages continuously adjustable: 1 - 3000 mm/min rapid move: 4 m/min electrical connection: 380 V kW space needed: 2000 + 850 x 2000 x 2000 mm weight: 3300 kg

Year of construction: 1986, condition: ready for operation (used), Travel X/Y/Z: 700mm/500mm/450mm, table dimensions X/Y: 900mm/500mm, max. table load: 500kg, spindle mount: SK40, speed: 3150rpm, quill stroke: 100mm, feed: 3m/min, rapid traverse: 6m/min, machine dimensions X/Y/Z: approx. 3550mm/3150mm/2100mm, weight: approx. 3600kg. On-site inspection is possible. Tjdpfx Ajwkihxjcnsb

Condition: ready for operation (used), Deckel Maho 5100027000 touch panel for Deckel Maho CNC 432 control unit, serial number as shown in the photo, used, with normal signs of wear, 100% functional, scope of delivery as shown in the photos. Tjdpfx Aji D Upgjcnsb

Condition: repair required (used), Year of construction: 2005, functionality: not functional, machine/vehicle number: 15125250184, travel distance X-axis: 2,500 mm, travel distance Y-axis: 920 mm, travel distance Z-axis: 820 mm, controller model: Heidenhain iTNC 530, spindle speed (max.): 18,000 rpm, Note: Error in the magnetic linear measuring system of the X-axis TECHNICAL DETAILS Number of axes: 3 Travel range of X-axis: 2,500 mm Travel range of Y-axis: 920 mm Travel range of Z-axis: 820 mm B-axis rotation: 105° Table length: 3,100 mm Table width: 900 mm Table length: 3,100 mm Table width: 900 mm Tool holder: SK40 Max. spindle speed: 18,000 rpm MACHINE DETAILS Control system: Heidenhain iTNC 530 Dimensions & Weight Dimensions (L x W x H): 7,500 x 4,500 x 300 mm Net weight: 22,000 kg Transport packages: 3 EQUIPMENT External cooling Chip conveyor Tool magazine (30 pieces) Todpfx Aozu Nyascnsb

Condition: ready for operation (used), Year of construction: 2011, operating hours: 12,946 h, functionality: fully functional, travel distance X-axis: 935 mm, travel distance Y-axis: 850 mm, travel distance Z-axis: 650 mm, controller model: Heidenhain iTNC 530 HSCI, spindle speed (max.): 15,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Travel range X-axis: 935 mm Travel range Y-axis: 850 mm Travel range Z-axis: 650 mm Number of axes: 3 Table length: 1,200 mm Table width: 850 mm Max. table load: 2,000 kg Tsdezwn Etopfx Acnsb Spindle connection: HSK-A63 Spindle speed: 15,000 rpm Tool changer: 30-position Rapid traverse: 40 m/min Feed rate: 40,000 mm/min MACHINE DETAILS Control system: Heidenhain iTNC 530 HSCI Internal cooling: 40 bar / 23 liters/min Operating hours: 36,420 h Spindle hours: 12,946 h EQUIPMENT Chip conveyor

Condition: good (used), Year of construction: 1997, Travel range X/Y/Z: 600mm/525mm/500mm Tsdpfx Ajzxq D Iocneb Spindle speed: 20 - 6300 rpm, continuously variable and programmable Tool holder: SK40 Feed rate: max. 10m/min Rapid traverse rate X and Y axes: 18m/min Documentation available (see images) Upon request, transport and loading can be arranged throughout Europe for an additional fee. Prices plus VAT. Inspection possible by appointment. Contact us, our team will be happy to assist you. Machine buying and selling PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, ETC. Hob Awypjzvflhoakst Do you need a high-quality but affordable machine for your production? Or do you want to sell yours? For further information or to contact us, please use the contact form.

Condition: ready for operation (used), Year of construction: 2005, operating hours: 35,880 h, travel distance X-axis: 500 mm, travel distance Y-axis: 450 mm, travel distance Z-axis: 400 mm, controller manufacturer: SIEMENS, controller model: 840D Powerline Shop Mill, spindle speed (max.): 10,000 rpm, number of slots in tool magazine: 30, tool weight: 6,000 g, number of axes: 5, This 5-axis DECKEL MAHO DMU 50 was manufactured in 2005. It features a digital swivel rotary table with a diameter of 630 mm and a maximum table load of 200 kg. The machine offers a rapid traverse of 24 m/min and a spindle speed range of 20 - 10,000 rpm. If you are looking to get high-quality machining capabilities, consider the DECKEL MAHO DMU 50 vertical machining centre we have for sale. Contact us for further details. - Table Type: Digital swivel rotary table- Table Dimensions: Diameter 630 mm x 500 mm- Max. Table Load: 200 kg- Swivel Range: 115 degrees (-5 / +110)- Table Features: Digital drives, hydraulic clamping (positioning mode only), electronic angle display, plane transformation- Spindle Speed Range: 20 - 10,000 rpm (steplessly variable)- Drive Power (100% / 40% duty cycle): 9 kW / 13 kW- Torque (40% duty cycle): 82 Nm- Measuring System: Direct linear measurement system X/Y/Z- Input Resolution X/Y/Z: 0.01 mm- Position Tolerance X/Y/Z: 0.010 mm- Rapid Traverse X/Y/Z: 24 m/min- Feed Rate: 20 m/min- Tool Changer Type: Chain magazine with double gripper- Tool Magazine Capacity: 30 tool positions SK40 (DIN 69871)- Max. Tool Diameter: D80 to D130 mm (speed-dependent)- Max. Tool Length: 290 mm- Max. Tool Weight: 6 kg- Coolant Unit Capacity: 80 l- Electrical Connection / Power Load: 17 kVA- Max. Current (Jn max): 28 A- Fuse / Supply Protection: 35 A- Voltage: 400 V / 230 V / 24 V- Frequency: 50 Hz- Footprint Dimensions (L x W x H): 4,860 mm x 4,350 mm x 2,424 mm- Transport Dimensions (L x W x H): 2,210 mm x 2,120 mm x 2,150 mm- Transport Weight: 4.05 t (4,050 kg) Additional Equipment: Right cabin door, Operating Mode 4, Coolant/blow-air switchover, Spray gun, Heidenhain TS641 Infrared touch probe, Electronic handwheel, Extra V24 RS232 interface in/on cabinet, MDE interface (machine on, machine running, part counter), Oil pan drawing, German documentation, 3D machine model for kinematic simulation (IGES, STEP format), Large quantity of SK40 (DIN 69871) tool holders included Todpjzxqb Tefx Acnjb

Condition: good (used), CNC control, control panel, control panel, control unit, card slot, control cards, MC3 control, plug-in cards, circuit boards, relay boards -Manufacturer: MAHO, relay board from CNC milling machine MH 800C -Type: 28A1 Todpfx Aceq T T I Ionsb -IDENT NO.: 27.71 231 -Dimensions: 400/280/H75 mm -Weight: 1.6 kg

Condition: like new (used), Year of construction: 2008, travel distance X-axis: 700 mm, travel distance Y-axis: 700 mm, travel distance Z-axis: 700 mm, feed rate X-axis: 60 m/min, feed rate Y-axis: 60 m/min, feed rate Z-axis: 60 m/min, nominal power (apparent): 68 kVA, controller manufacturer: HEIDENHAIN iTNC 530, workpiece height (max.): 1,000 mm, workpiece diameter (max.): 800 mm, workpiece weight (max.): 600 kg, total height: 2,547 mm, total length: 5,866 mm, total width: 4,196 mm, table width: 500 mm, table length: 500 mm, overall weight: 12,000 kg, spindle speed (max.): 18,000 rpm, spindle motor power: 34,000 W, number of slots in tool magazine: 120, Equipment: chip conveyor, documentation/manual, CNC controller: HEIDENHAIN iTNC 530 Axes: X-axis travel mm: 700 Y-axis travel mm: 700 Z-axis travel mm: 700 Distance spindle nose - table surface mm: 100 - 800 Tsdpfswhdhzox Acnsb Rapid traverse m/min: 60 Acceleration in the axes m/s2: 6 / 6 / 5 Worktable: Number of pallets: 2 + 5 Table dimensions mm: 500 x 500 Maximum workpiece size (D x H) mm: 800 x 1.000 Max. workpiece weight kg: 600 T-Slot version: DIN 55201-A2 APC time s: 9,5 División estandar Grados: 360º (1º) Spindle: Spindle speed rpm: 18.000 Spindle drive power kW: 34 / 28 Spindle torque Nm: 110 Tool system: Tool holder: HSK-A63 Tool magazine slots: 120 Max. Tool Diameter: 80 Max. Tool Length mm: 550 Max tool weight kg: 12 Chip-to-chip time s: 2,9 Equipment: Electronic Handwheel Chip conveyor Rotating inspection windows Rinsing gun Signal lamp Tool breakage probe 3D quickSET Workarea light CE conformity Cooling device blowing air through spindle center, selectable via M-function MPC – Machine Protection Control Paper band filter Infrared Probe Heidenhain TS640 Blum laser tool measurement Taper clear brushes Blum laser NT Hybrid Round pallet Storage (RPS 5) Measuring probe Heidenhain TS 640 Production package Internal cooling supply 40 BAR Cooling: Cooling through the Spindle Center bar: 40 BAR Tank capacity: 980 High-pressure bar: 40 BAR Machine running times: Under power: 95.210 Operating Time: 44.971 Rated power kVA: 68 Basic machine dimensions / weight: Length mm: 5.866 Width mm: 4.196 Height mm: 2.547 Weight kg: 12.000.

Condition: excellent (used), Year of construction: 1999, x-travel 500 mm Tjdpfxezxh Tao Acneb y-travel 400 mm z-travel 400 mm

Condition: used, MAHO MH 600 P Tool Milling Machine Tool Milling Machine MAHO Type/Model MH 600 P Control Heidenhain TC 135 Condition Used Technical Data Travel (X / Y / Z): 500 mm / 400 mm / 400 mm Quill stroke: 80 mm Table dimensions: 720 mm x 140 mm Max. table load: approx. 500 kg T-slots: 8 pieces (spacing 54 mm) Tool holder: SK 40 / ISO 40 Spindle speed range: 40 to 2,000 rpm Tsdpfx Acozxhfvsnob Spindle drive power: 4.0 kW Working feed rate continuously adjustable: 5 to 500 mm/min Rapid traverse speed (X / Z): approx. 1.2 m/min Rapid traverse speed (Y): approx. 0.8 m/min Connection voltage: 380 V / 50 Hz Machine weight: approx. 1,450 - 1,900 kg Space requirement (L x W x H): approx. 1.8 m x 1.5 m x 1.9 m

Condition: used, MAHO MH 600 P Tool Milling Machine Tool milling machine: MAHO Type/Model: MH 600 P Control: Heidenhain TC 135 Condition: Used Technical data Travel distances (X / Y / Z): 500 mm / 400 mm / 400 mm Quill stroke: 80 mm Table dimensions: 720 mm x 140 mm Max. table load: approx. 500 kg T-slots: 8 pieces (distance 54 mm) Tool holder: SK 40 / ISO 40 Spindle speed range: 40 to 2,000 rpm Spindle drive power: 4.0 kW Working feed rate continuously adjustable: 5 to 500 mm/min Rapid traverse speed (X / Z): approx. 1.2 m/min Rapid traverse speed (Y): approx. 0.8 m/min Connection voltage: 380 V / 50 Hz Machine weight: approx. 1,450 - 1,900 kg Tedpfx Aozxgwdecnjb Space requirement (L x W x H): approx. 1.8 m x 1.5 m x 1.9 m Inquiry item: Transportation costs will be provided in a separate, customized offer.

Condition: ready for operation (used), Year of construction: 2000, operating hours: 6,328 h, functionality: fully functional, machine/vehicle number: 11180000573, travel distance X-axis: 1,250 mm, travel distance Y-axis: 880 mm, travel distance Z-axis: 800 mm, workpiece weight (max.): 1,000 kg, spindle speed (max.): 18,000 rpm, TECHNICAL DETAILS Travel range X-axis: 1,250 mm Travel range Y-axis: 880 mm Travel range Z-axis: 800 mm C-axis indexing: 360° (0.001°) Feed rate: 40 m/min Rapid traverse: 40 m/min Tsdpfxezxf Ins Acneb Number of pallets: 1 Pallet dimensions, diameter: 1,000 mm Max. workpiece weight: 1,000 kg Max. torque: 7,900 Nm Max. spindle speed: 18,000 rpm Spindle drive power: 15 kW at 40% duty cycle Spindle drive power: 10 kW in continuous operation Tool interface: CAT 40 Number of tool positions in the magazine: 60 Tool changer: Double gripper MACHINE DETAILS CNC control: 3D contouring control MillPlus Total power consumption: 55 kVA Coolant tank capacity: 600 l Dimensions (L x W x H): 7,000 x 3,500 x 3,902 mm Operating hours Hours under power: 33,831 h Spindle operating time: 6,328 h EQUIPMENT Electronic handwheel Chip conveyor Internal coolant supply Rotating viewing windows Flushing gun Preparation for Renishaw probe Accuracy package Preparation for internal cooling with 40/80 bar Paper band filter

Condition: used, Year of construction: 2012, Deckel Maho NHX 4000 Horizontal Machining Center Horizontal Machining Center, Deckel Maho Type / Model: DMG NHX 4000 Condition: Used Year of Manufacture: 2012 Program Runtime: approx. 48,200 hours Spindle Hours: approx. 39,200 hours Technical Data Travel ranges X / Y / Z axis: 560 mm / 560 mm / 660 mm Rapid traverse rate (X/Y/Z): 60 m/min Work table & Pallets Pallet size: 400 x 400 mm Max. workpiece weight: 400 kg Max. workpiece dimensions (Ø x H): Ø 630 x 900 mm Tedszxc H Ujpfx Acnob Pallet change time: approx. 8.0 seconds B-axis (rotary table): 360° (increment 0.001°, direct drive) Main spindle: 12,000 1/min Max. speed: 12,000 1/min Drive power: approx. 15 kW (or up to 30 kW in special/power versions) Max. torque: approx. 110 Nm Tool interface: SK 40 or HSK-A63 (depending on the exact spindle design from the factory) Tool changer (ATC) Magazine slots: Usually 40 stations as standard Max. tool diameter: 70 mm (up to 170 mm with free neighboring slots) Max. tool length: 450 mm Max. tool weight: 12 kg Dimensions & Weight Machine weight: approx. 7850 kg Footprint / Dimensions (W/D/H): approx. 2,860 x (width varies depending on the chip conveyor) x 2540 mm Control system (standard model year 2012): MAPPS IV based on Fanuc (alternatively Siemens 840D) Inquiry item: Transport costs in an individual offer.

Condition: used, Year of construction: 2008, Deckel Maho DMC 55H duoBlock Horizontal Machining Center Horizontal Machining Center Deckel Maho Type / Model DMC 55 H DuoBlock Year of Manufacture 2008 Condition Used Program Runtime: approx. 66,600 hours Spindle Runtime: approx. 46,500 hours Technical Data Travel distances X / Y / Z axes 560 mm / 600 mm / 600 mm Rapid traverse (X/Y/Z) 40 m/min (optional in the linear version or high-dynamics up to 60 m/min) Work table & Pallet Changer (APC) Number of pallets 2-position pallet changer Pallet size 400 mm x 400 mm Max. workpiece weight 500 kg Max. workpiece height 850 mm B-axis (rotary table) 360° (designed as an NC rotary table, usually with 0.001° division) Main spindle Standard version 12,000 rpm (often with SK 40 / HSK-A63) High-speed option 18,000 rpm (standard with HSK-A63) Tool changer (ATC) Tjdezxc Ewjpfx Acneb Magazine positions Standard 60 stations Tool interface HSK-A63 (alternatively SK 40 or BT 40) Max. tool diameter 80 mm (with free neighboring positions up to 160 mm) Max. tool length 330 mm Dimensions, weight & control Machine weight approx. 11,000 kg to 13,000 kg (depending on magazine size and chip conveyor) Footprint (L x W x H) approx. 5.0 x 3.0 x 2.8 m (pure space requirement without peripherals) Control Siemens Sinumerik 840D Powerline / Solution (alternatively Heidenhain iTNC 530)

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, Deckel Maho DMC 103V Vertical Machining Center The machine is in good condition and can be inspected while powered on at any time. Technical data: Year of manufacture: 2003 Todpfx Ajzw U Rcocneb Control system: Heidenhain TNC 426 / 43 Travel ranges: X: 1000 mm Y: 600 mm Z: 600 mm Spindle: 10,000 rpm Tool holder: SK40 ATC with 24 positions Table: 1200 x 600 mm Weight: approx. 6,750 kg Dimensions: 410 x 242 x 275 cm Accessories and options: Coolant tank Electronic handwheel with 3D path control Cooling system with compressed air Operating mode 4 Documentation

Condition: good (used), Year of construction: 2008, Ref. -No.: 10660 Manufacturer: DECKEL MAHO Type: DMC 835 V Year of construction: 2008 Type of control: CNC Control: Siemens 840D mit Shopmill Storage location: Halberstadt Country of origin: Germany X-Travel: 835 mm Y-Travel: 510 mm Z-Travel: 510 mm Todpfxezw Txfj Acnsb Main spindle drive power: 14 kW Table Dimensions (Lengthxwidth): 1000 x 560 mm Table Load: 800 kg Tool Taper: SK 40 Numbers Of Tools In Magazin: 20 Turning Speeds: 10000 RPM Max. Workpiece Weight: 4,5 t Further information: - Chip conveyor - Handwheel The machine can be inspected while powered on by prior arrangement.