Used Grain for sale (695)

Condition: new, machine/vehicle number: 8df1ead53cc82aeb51e50a37d, empty load weight: 4 kg, maximum load weight: 13,880 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Nkedpfxoi Ri Nuj Ad Not Chassis Turntable Disposal Fine-grained steel welded construction Container locking system: - 2 pairs of locking hooks embedded in the floor - Pneumatic actuation The container locking mechanism is a 2-point design, acting from the inside, and locking of roll-off containers with an inner web is not possible (for transporting roll-off containers with a sub-frame in accordance with DIN 30722) Note! At the start of the roller recess at the front, the container must be pushed on completely flat! Longitudinal guide rails can be moved sideways and removed, rails approx. 115 mm high Turntable with strong ball bearing slewing ring 8 pairs of lashing mushrooms at the top and sides of the outer frame, 5 tons each 7 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Quarter-shell mudguards according to EG with anti-spray flaps according to EG Towing equipment Trailer turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, floor Steel floor Roller recess for container recessed in the floor at the frontfor roll-off containers from 5,000 - 7,000 mm in length Note: Slight floor undulation possible due to welding distortion! Drive-on ramps Lockable storage space for loading ramps underneath the loading area Operating instructions A special permit is required for axle loads of 10,000 kg. Approval must be applied for individually in each federal state; the legislator does not have to grant approval for 20 t GG. Customer risk. The specified total weight is technically possible; depending on the load, the total weight may not be achieved while complying with the permissible axle/support and fifth-wheel loads. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Warning sign according to ECE - 70 Paint finish Frame DB 7350 nova gray 15-year warranty against rusting through Note: Bottom corrugation possible due to hot-dip galvanizing! Drawbar KTL black Attention: Archive pictures!

Condition: new, machine/vehicle number: c78894767223a51dd199030f3, empty load weight: 4,600 kg, Further information Frame Welded steel construction made of fine-grained steel, hot-dip galvanized, flat plateau without raised edges, Loading area slanted downwards by approx. 8° after the rear axle. Side members made of steel profiles, Hot-dip galvanized steel frame, with stainless steel plate at the kink as cable guide - flush with the floor. For trucks with Wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4105 mm and 3rd to 4th axle 1350 mm Trailer coupling Towing hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, incl. assembly and electrics with 7-pin socket Accessories/conversions 2 holders for wheel chocks, aluminum side bumpers, foldable - are taken from the truck! Steel underride guard, quarter-shell mudguards with mud flaps - will be taken from the truck! Storage box Plastic tool box, with drawer and shelf, w=650 Incl. / h=520 / d=670 mm, lockable with a padlock (lock not included). not included) 1 holder for 3 pcs. petrol cans 1 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, incl. lockable, includes control valve. lockable, includes control valve and electro-hydraulic pump unit. pump unit. Control box with circumferential door seal and sealing sleeves on the back (splash-proof according to techn. technical possibility) Electrics Adaptation of the existing rear lights, 2 additional LED work lights, recessed in the bulkhead recessed switched via parking light with switch on front wall outside in FR-left, 1 LED work light, at the rear, with integrated reversing camera Incl. with color flat screen monitor, screen with suction cup mount and power supply via 24 volts, Voltage divider 24/12V, 1 socket 7-pin 12V = plug-in adapter Base Mega Grip made of toothed galvanized grating, steel grating 50/4 Incl. with mesh width 50 mm. Top side with anti-slip serration, laid continuously over the entire main frame plateau Nkodpfsk Unitsx Ad Njt Lashing eyes 12 pairs of lashing rings suspended freely pivoting in the outer frame - 10 tons each. 1 x at the front and the last one at the rear. 1 piece Lashing eyelet at the very rear in the middle for fastening the winch cable 12 lashing eyes centrally embedded in the floor, each 5 to. (not included in Inkl. rear slope) Front wall Sheet steel bulkhead, height 1,500 mm. Fixed with corner pillars at front wall height. Each with 2 x 12 pcs. Suspension brackets for lashing chains mounted on the left and right of the front wall Cable winch Electric cable winch, 24 volt, pulling force approx. 6350 kg, mounted in the center of the bulkhead (recessed with loading bridge), operation with radio remote control, cable length min. 35 m x 9.5 mm, with roller rope window, with cable pressure plate, incl. overload protection, cable freewheel clutch, manual switch with approx. 5 m control lever, acceptance of the cable winch, civil engineer test report, test book, operating instructions Drive-on ramps Length 3,500 mm - 2-part (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also for ramp loading), electric for ramp loading), electro-hydraulically foldable and laterally movable - incl. Electro-hydraulic pump unit. Drive-on angle approx. 8° with lowered rear axle Ramp support made of hot-dip galvanized steel grating (like the floor of the loading bridge), with with anti-skid toothing. Ramps can be pushed together to approx. 170 mm, Hydraulic ramp extension. Ramp prepared for operation on loading ramp with full load capacity. Ramp locking with 2 tension

Condition: new, machine/vehicle number: 59ade5d1599dcdee29033ac46, empty load weight: 6,350 kg, maximum load weight: 28,650 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Suspension bar for aluminum ramps across the entire width Frame in reinforced design for vehicle loading (up to outer frame) Outer frame with Load-Lock profile approx. every 400 mm, for lashing strap attachment 10 pairs of lashing mushrooms embedded in the top/outside of the outer frame, 10 tons each 24 to. 2-speed support winch, single-sided operation, with semicircular lower section and straight connecting plate, with thrust compensation Folding rear support 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle with anti-spray flaps behind each axle Nkjdpfold Ihljx Ad Nst Pair of ferry eyes, marked yellow 1 Spare wheel holder for 1 e-wheel, with wheel mounting kit 2 plastic toolboxes, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) Container lock, 4 pairs of locks embedded in the floor for 2 x 20 foot or 1 x 40 foot containers, foremost position recessed as hinged lock 10 pairs of stake pockets embedded in the outer frame, 70 x 40 mm internal dimensions 10 stake pockets embedded in the center of the floor, 70 x 40 mm inside dimensions 2 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 rdnung: Position 2 and 4 according to Fliegl data sheet 20 stanchions, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them Storage space for aluminum ramps, ramps can be inserted from the rear 3 pairs of folding eyelets 10 tons in the outer frame (1x in front of the bulkhead and 2x in the rear area). Axles + suspension SAF disk brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage 2 ride heights, adjustable via hand knob, 1 x for semi-mounted height 980 mm 1 x for semi-mounted height 1100 mm (Note! Vehicle with inclined position) Brake system 2-line compressed air brake system Colored cable routing for easy servicing. Spring-applied parking brake 2 interchangeable clutch heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting & lowering valve 2 ride heights, adjustable via hand knob, 1 x for fifth wheel height 980 mm 1 x for fifth wheel height 1100 mm (Note! Observe overall height, excess height at customer risk) Driving height in conjunction with lift axle, when the lift axle is raised, the total loading or semitrailer height increases by 50 mm (with Mega Flex only with low driving height or semitrailer height) Vehicle driving stability system Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Stee

Condition: new, machine/vehicle number: 637ca014c140e4e48dc3231a0, empty load weight: 5,900 kg, maximum load weight: 29,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 Nkedpoi Rivdofx Ad Nst 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: new, machine/vehicle number: f80f2330e1318ef03bc20755e, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Fine-grained steel welded construction in lightweight design, saddle plate with replaceable 2 kingpins, only 2 longitudinal beams as double T-beams for retrofitting connecting gallows at the front in new/current design, outer frame slightly slanted with load-lock profile for attaching tension beltsNote! to attach the belts in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, wheel chocks with holder, aluminium side bumper, foldable, galvanized steel underride guard, extendable, half-shell mudguards!!! enclosed loose, not mounted!!!, with anti-spray flaps behind each axle, 1 plastic water barrel, capacity approx. 30l, in FR left BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction of tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, can also be lowered manually, can be operated with a hand button on the vehicle 2-line compressed air brake system, with 1 air reservoir central standard, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module laid to the outside, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, control unit + brake integrated in frame as with tipper semi-trailer, mounted in front of the axles Brake pad wear indicator for disc brakes via ABS/EBS lamp Truck 385/65 R22.5 Continental tires, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the side as for tipper semi-trailer, dimension 3000 mm must be observed, 2 white LED position lights at the front, loose, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Germany, test approval according to EC 2007/46 for complete vehicle, 24/7 service hotline, prepared for double license plate holder single-line1 x plastic and 1 x stainless steel interchangeable holder Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strips according to ECE R 048, Frame: DB 7350 nova gray, support legs: black coated Available immediately! Nkedoi Riwqjpfx Ad Net

Condition: new, machine/vehicle number: 7383bc2b7f580f0cb319b52f7, empty load weight: 5,300 kg, maximum load weight: 29,700 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Nkedoi Rix Ispfx Ad Nst Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Contour marking

Condition: new, machine/vehicle number: 824d4741dc933a94e9a7a7a8c, empty load weight: 5,600 kg, maximum load weight: 29,400 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Surface stone-repellent Splash guard behind last axle in asphalt version, attached to mudguard with hinge, with attachment option on top of mudguard, shortened mudguard Tow hook at the rear Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension Nedpfxei Rix Sj Ad Nekt 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics High-pressure cylinder max. 250 bar, with HDK screw socket, fixed part, NW 48 mm (without hose connection) Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Membrane rear wall Rear wall as pendulum flap, resting on the outside with 2-fold hook locking. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Insulated body, Fliegl Asphalt Profi Thermo, body insulated at the front, sides, bottom and rear with Fliegl Isotherm. BASIC cover, tarpaulin cladding Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) Body strength according to EN 12642 24/7 service hotline Manufacturer certificate for thermal vehicles according to RS 10 - 2013 Prepared for single-line license plate holder Contour marker

Condition: new, machine/vehicle number: 81b04fd2e28f354df79a4c3b3, empty load weight: 3 kg, maximum load weight: 14 kg, overall weight: 18 kg, axle configuration: 2 axles, tire size: 235/75 r17,5``, Further information Chassis Wechel central axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear Folding locking adapter + height adjustment for parking height 1,000 - 1,120 mm, center supports can be folded and guide rollers can be pushed upwards, 4 container locking devices with sturdy outriggers on 20-basefor swap bodies 7.15 / 7.45 and 7.82 1 pair of gear support legs at the front, with straight lower section and single-sided operation in FR right 2 wheel chocks with holder Aluminum side bumpers Steel underride guard Half-shell mudguards Towing device central axle trailer Towbar with tested 50 mm towing eye, forwarding agent version (not suitable for trucks with tail lift, or exact testing still required in case of order) Under-coupler drawbar, free drawbar length approx. 2200 mm Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake systemColor-coded line routing for easy servicing. Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the engine trolley, connection in FR-right EBS, electronic brake system with EBS plug at the front, with connecting cable, connection in FR right-hand side Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in each case in lowering / lifting position Vehicle - driving stability system Wheels and tires 235/75 R17.5`` tires of the manufacturer's choice Steel rims in twin arrangement, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 1 x 15-pin plug at the front, with connecting cable, connection in FR right-hand side 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Nkedpsi Riy Nsfx Ad Njt Country of registration / plates Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour markings with reflective strips to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Attention: Archive pictures!

Condition: new, machine/vehicle number: 113bec9dd54d24fa34a088424, empty load weight: 4,400 kg, maximum load weight: 27,600 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Nkjdpfxei Rizio Ad Nst Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, machine/vehicle number: 7d479432c7290a73a46ff6365, empty load weight: 5,000 kg, maximum load weight: 30,000 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Patented curved front end Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. Wheel chocks with holder Underride guard, foldable Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Nkodpfsi Ri Dpjx Ad Njt Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty

Condition: new, machine/vehicle number: e7fbe178b85a202cade7e95af, empty load weight: 5 kg, maximum load weight: 22 kg, overall weight: 29 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis saddle forwarding Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, with 2 king pin positions Slightly angled outer frame with load-lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! 2 pairs of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 8 pairs of lashing eyes embedded in the outer frame in the low bed, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards in front of and behind axle unit 2 Stainless steel stowage box, w=600/h=400/t=500 mm, with polished door, lockable 2 pairs of stake pockets recessed in the outer frame on gooseneck, 70 x 40 mm internal dimensions 6 pairs of stanchion pockets in the outer frame recessed in the deep bed, 70 x 40 mm Internal dimension!!! Internal width between the stanchions 2420 mm!!! 3 lashing/stanchion rails in the drop-down bed, embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Piece of stanchions W=80/ D=50/ L=1200 mm, hot-dip galvanized Piece of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, with support beam, can be loaded with 2000 kg over the entire width at the load center of gravity at approx. 500 mm, can be loaded with 1000 kg over the entire width at 1000 mm and can be loaded with 500 kg over the entire width at 1500 mm, incl. extendable underride guard with lighting, 2 pairs of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Open storage compartment for stanchions, on the front wall or underneath the loading area (for 10 stanchions 80 x 50 x 1200 mm and 4 stanchions 80 x 80 x 1200 mm) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Nkodpfsi Ri Hvox Ad Nst Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales). Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin sockets at the front, without connecting cable 2 additional LED work lights, at the rear, switched via reversing light 1

Condition: new, machine/vehicle number: 057736dac221bda3fc469966a, empty load weight: 3 kg, maximum load weight: 8 kg, overall weight: 11 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis central axle trailer Fine-grained steel welded construction Slightly sloping outer frame with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! Front gear support leg Folding rear support 2 wheel chocks with holder Galvanized steel underride guard Quarter-shell mudguards 1 plastic tool box, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) 1 open storage compartment for stanchions, underneath loading area 4 pairs of stanchion pockets embedded in the outer frame, 83 x 83 mm internal dimensions 4 stake pockets centrally recessed in the floor, with reinforcements to the main frame, 83 x 83 mm internal dimensions 6 pairs of stanchions W=80/ D=80/ L=2000 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Tandem trailer drawbar Drawbar with tested 40 mm drawbar eye Drawbar mechanically adjustable in length by 4 x 500 mm from 1800 - 3800 mm, drawbar length set to 1800 mm, (Note! Observe load distribution and drawbar load) Axles + suspension GFA axles with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake Integral air reservoir 2 non-interchangeable coupling heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, Floor Screen printing plates approx. 30 mm thick, for high point load capacity Note: Floor warping due to weather influences possible! Platform length approx. 6,200 mm Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. Approval / plates Country of registration: Germany With Dekra approval and expert opinion 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray Attention: Archive pictures! Nkedpfji Ri H Dsx Ad Net

Condition: new, machine/vehicle number: ccd5fddabaca94f260d9fe895, empty load weight: 2,950 kg, maximum load weight: 15,050 kg, overall weight: 18,000 kg, axle configuration: 2 axles, tire size: 445/45 r19,5, Further information Chassis Changing turntable Fine-grained steel welded construction Fliegl V-Stream frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Side collision protection set inwards, for optimum clearance to the swap body supports Steel underride guard Underride guard shortened for optimum clearance to the swap body supports, lighting system mounted protected Quarter-shell mudguards at the front and half-shell mudguards at the rear Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Air supply 208 liters Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, holding function in both lowering and lifting position Wheels and tires 445/45 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable plugs at the front, with connecting cable, 2 additional LED work lights at the rear, switched via reversing light 1 LED work light at the front, centered between the carriers, radiating to the rear, switched via reversing light Country of registration / plates Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray 10-year warranty against rusting through Attention: Archive pictures! Nkedpsi Ri Rksfx Ad Not

Condition: new, machine/vehicle number: d9c951d746f03c05bc5470f89, empty load weight: 5 kg, maximum load weight: 29,045 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis saddle forwarding Fine-grained steel welded construction, saddle plate with replaceable 2 kingpins Vario stanchion system 4 pairs embedded in loading area, can be pushed together to 2 100 mm and extended to approx. 3 500 mm for loading. Stanchions can be locked every 100 mm on an internal width of 2 100 mm to 3 000 mm, 4 pairs of divisible stanchions 600 mm + 1 200 mm, total height 1 800 mm removable. With an internal stanchion width from approx. 2 350 mm, excess width. Vario end walls Floor prepared for inserting 3 end walls. 4 x 5 pairs of Vario stanchion pockets for insertable end walls (front and rear) and 1 x 3 pairs in the middle for transporting 2 x 5,000 mm or 2 x 6,000 mm construction steel mats. 2 Vario end walls, each consisting of 1 pair of plug-in stanchions and 1 top crossbeam approx. 2200 mm wide. Cross beams can be extended by 220 mm on both sides, with lashing hole for tensioning. 1900 mm high Vario bulkhead, can be converted to 1300 mm or 700 mm high. 4 stanchion pockets embedded in the center of the floor for 80 x 80 mm stanchions 1 pair of supports at the bottom for Vario bulkhead at the front 1 pair of lower supports for rear Vario bulkhead Nedpfxei Ri R Ds Ad Nokt Slightly slanted outer frame with Load-Lock profile for lashing strap attachment 14 pairs of lashing eyes additionally embedded in the outer frame, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Extension ladder at the rear Wheel chocks with holder Aluminium side collision protection Galvanized steel underride guard Quarter-shell mudguards in front of and behind axle unit with anti-spray flaps on last axle only Impact protection at the rear 8 construction steel winches with wire rope and counter hooks, 4 x left and 4 x right with rope feed-through through the outer frame, 1 removable slip-on gearbox for construction steel winches - supplied loose (without bracket on the frame) 1 spare wheel holder for 1 e-wheel, with wheel fastening set 1 plastic toolbox, with drawer and shelf, w=650 / h=520 / d=670 mm, lockable with a padlock (lock not included) 1 closed stanchion stowage box, open at the top, below loading area, doors on both sides, w=450 mm/h=400/420 mm/d=2460 mm 4 lashing/stanchion rails embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Axle lift below the recomm. Driving height, therefore no warranty for tire damage Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 swap-proof coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be to

Condition: new, machine/vehicle number: 357314e4e176f8758d11ba42b, empty load weight: 4,500 kg, maximum load weight: 30,500 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Nkjdpfxei Ri R Io Ad Njt Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear

Year of construction: 2020, condition: refurbished (used), For suction diameters from 120 to 700 mm. Please let us know your volume flow and we will select the right cyclone for you. Different versions available: - Legs, made of painted square steel profiles - Rotary valve and transition piece with inspection flap - Inlet box with non-return valve - Tangential outlet with/without pressure relief surface - Square diffuser with/without pressure relief surface - Sound insulation Of course you can also obtain all accessories from us such as fans, exhaust pipes, deflector hoods etc. Functionality: The polluted air is tangentially fed into the cylindrical upper part is introduced, causing the air to rotate. The material is placed under the Influence of the centrifugal force in the direction of the cyclone circumference pressed out and led out through the hole in the bottom. The cleaned air leaves the cyclone through the centrally located Outlet pipe on top. The deposition efficiency increases with the feed rate, but also the pressure loss and thus the energy consumption. It is therefore it's important to find a good compromise. We have developed a range of cyclones optimised for filtering large quantities of material. They are therefore very well suited for the wood/paper/recycling/grain and feed industry At the bottom, the cyclone can be designed with the correct size based on the air volume and a typical pressure drop in the range of 1000 Pa Nkodjftb Ebepfx Ad Nst can be selected. Operating pressure +/- 5

Condition: as good as new (ex-display), Year of construction: 2025, GT 40 - The OPTIMUM premium NC sanding machine with Siemens touch screen. - Electromagnetic clamping plate for fixing the workpiece with automatic demagnetization function - High-quality spindle with precision tapered roller bearings - Hardened and ground table guideways - Turcite-B coated counter guides for high wear resistance and low friction - Grinding spindle with high-quality precision bearings - Grinding wheel can be resharpened directly on the machine using a sharpening device - Digital position indicator - Machine base made of sturdy torsion-resistant cast iron for maximum rigidity and stability - Guideways for longitudinal, transverse and vertical movements are backlash-free and self-centring as V and flat tracks - Precision recirculating ball screws - Guideways and transport spindle with central lubrication - All flat guides are finely scraped and thus guarantee maximum precision of all manual movements B9errbkz8v - Safety electrics with 24 V DC voltage - Large decoupled handwheels in all three axes - Hydraulic lines according to DIN EN 853 - Grinding accuracy: 0.005 mm - Grain 46 corundum grinding wheel for all common steels - Swivel-mounted control panel makes work considerably easier - Separate hydraulic unit with heat exchanger, avoids vibrations and thermal stress - Two-channel safety electronics - Grinding table splash guard - EMC filter class - With IE3 motor - consumes considerably less energy, resulting in significant cost savings Dimensions and weights Length approx. 3600 mm Width/depth approx. 2400 mm Height approx. 1900 mm Weight approx. 3600 kg Electrical data Total connected load 7.5 kW Supply voltage 400 V Mains frequency 50 Hz Njdpfxoxyhvks Ad Nekt Surface grinding table Clamping surface length 400 mm Clamping surface width 800 mm Grinding wheel(s) Outer diameter 350 mm Width 40 mm Bore 127 mm Peripheral speed 27 m/s Spindle Speed 1450 min¯¹ Concentricity 0.005 mm X-axis Feed speed 5 - 25 m/min Digital position indicator Coolant device Balancing mandrel Grinding wheel grit 46 Diamond pin Operating tool Manual oil pump LED lamp Electromagnetic clamping plate Demagnetizing function Equipment Electromagnet clamping plate Splash guard table enclosure Demagnetizing device Parallel dressing device ✔ Coolant device 125 W Work light LED lamp Alignment feet ✔

Condition: as good as new (ex-display), Year of construction: 2025, GT 30 - The OPTIMUM premium NC sanding machine with Siemens touch screen. Nkodpsw Eazfofx Ad Net - Electromagnetic clamping plate for fixing the workpiece with automatic demagnetization function - High-quality spindle with precision tapered roller bearings - Hardened and ground table guideways - Turcite-B coated counter guides for high wear resistance and low friction - Grinding spindle with high-quality precision bearings - Grinding wheel can be resharpened directly on the machine using a sharpening device - Digital position indicator - Machine base made of sturdy torsion-resistant cast iron for maximum rigidity and stability - Guideways for longitudinal, transverse and vertical movements are backlash-free and self-centring as V and flat tracks - Precision recirculating ball screws - Guideways and transport spindle with central lubrication - All flat guides are finely scraped and thus guarantee maximum precision of all manual movements - Safety electrics with 24 V DC voltage - Large decoupled handwheels in all three axes - Hydraulic lines according to DIN EN 853 - Sanding accuracy: 0.005 mm - Grain 46 corundum grinding wheel for all common steels - Swivel-mounted control panel makes work considerably easier - Separate hydraulic unit with heat exchanger, avoids vibrations and thermal stress - Two-channel safety electronics - Grinding table splash guard - EMC filter class - With IE3 motor - consumes considerably less energy, resulting in significant cost savings Dimensions and weights Length approx. 3200 mm Width/depth approx. 2200 mm Height approx. 2100 mm Weight approx. 3000 kg Electrical data Total connected load 6.5 kW Supply voltage 400 V Mains frequency 50 Hz Surface grinding table Clamping surface length 300 mm Clamping surface width 600 mm Grinding wheel(s) Outer diameter 350 mm Width 40 mm Bore 127 mm Peripheral speed 27 m/s Spindle Speed 1450 min¯¹ Concentricity 0.005 mm X-axis Feed speed 5 - 25 m/min Scope of delivery Unit of measure: piece Packaging unit: 1 Digital position indicator Coolant device Balancing mandrel Grinding wheel grit 46 Diamond pin Operating tool Manual oil pump LED lamp Electromagnetic clamping plate Demagnetizing function Equipment Electromagnet clamping plate Splash guard table enclosure Automatic demagnetizing device Parallel dressing device ✔ Coolant device 125 W Work light LED lamp Alignment feet ✔

Condition: as good as new (ex-display), Year of construction: 2025, GT25 - The OPTIMUM premium NC sanding machine with Siemens touch screen. - Electromagnetic clamping plate for fixing the workpiece with automatic demagnetization function - High-quality spindle with precision tapered roller bearings - Hardened and ground table guideways - Turcite-B coated counter guides for high wear resistance and low friction - Grinding spindle with high-quality precision bearings - Grinding wheel can be resharpened directly on the machine using a sharpening device - Digital position indicator - Machine base made of sturdy torsion-resistant cast iron for maximum rigidity and stability - Guideways for longitudinal, transverse and vertical movements are backlash-free and self-centring as V and flat tracks - Precision recirculating ball screws - Guideways and transport spindle with central lubrication - All flat guides are finely scraped and thus guarantee maximum precision of all manual movements - Safety electrics with 24 V DC voltage - Large decoupled handwheels in all three axes - Hydraulic lines according to DIN EN 853 - Sanding accuracy: 0.005 mm - Grain 46 corundum grinding wheel for all common steels - Swivel-mounted control panel makes work considerably easier - Separate hydraulic unit with heat exchanger, avoids vibrations and thermal stress - Two-channel safety electronics - Grinding table splash guard - EMC filter class - With IE3 motor - consumes considerably less energy, resulting in significant cost savings Technical data: Dimensions and weights Length approx. 2300 mm Width/depth approx. 1600 mm Height approx. 1675 mm Weight approx. 1700 kg Electrical data Total connected load 3 kW Supply voltage 400 V Phase(s) 3 Ph Oc8fv Current type AC Mains frequency 50 Hz Surface grinding table Length 254 mm width 508 mm Grinding wheel(s) Outer diameter 200 mm width 20 mm Bore 31.75 mm Peripheral speed 33 m/s Nedpfx Asw Eayhod Njkt Spindle Speed 2850 min¯¹ Concentricity 0.005 mm X-axis Feed speed 5 - 25 m/min PU 1 Scope of delivery Unit of measure: piece Packaging unit: 1 Digital position indicator Coolant device Balancing mandrel Grinding wheel grit 46 Diamond pin Operating tool Manual oil pump LED lamp Electromagnetic clamping plate Demagnetizing function Equipment Electromagnet clamping plate Splash guard table enclosure Automatic demagnetizing device Parallel dressing device Coolant device 40 W Work light LED lamp Alignment feet

Condition: used, mileage: 656,928 km, power: 331 kW (450.03 HP), first registration: 05/2017, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: green, gearing type: automatic, emission class: euro6, total width: 2,550 mm, total height: 4,000 mm, loading space volume: 41 m³, loading space length: 7,100 mm, loading space width: 2,460 mm, loading space height: 2,350 mm, Year of construction: 2017, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, Scania R 450 LB 6x2?4MSA VIN: 9224161 Chassis / Attachments: * Wheelbase: 4,600 mm / 1,350 mm * Leaf / Air suspension * Lift axle // Steering axle * Tyres: 1st axle 385/55 R22.5, 2nd + 3rd axles 315/70 R22.5 * Remaining tread: front approx. 20/30%, middle approx. 40/70%, rear approx. 80/30% * 1 x aluminum fuel tank 500 L * 1 x AdBlue tank * 1 x hydraulic tank * 1 x Bawer stainless steel toolbox Cab: * CR 19 H Highline * 2 x bunks * Automatic climate control * Auxiliary heater * Refrigerator * Radio CD // CB radio Nkedpfx Ajvg T Rqsd Not * USB, AUX, BT * Navigation system * Distance control Body: * HGE grain tipper * Standing platform * Sliding tarpaulin * Drop sides 800 mm * Folding central stanchion * Internal tarpaulin * Body dimensions: 7,100 mm x 2,460 mm x 2,350 mm * Load volume: approx. 40 m³ * Grain discharge chute Engine / Transmission: * 12,742 cc // 450 HP / 331 kW // EURO 6c * Opticruise / automatic * Scania retarder * Differential lock Weights: * Gross vehicle weight: 26,000 kg * Unladen weight: 11,680 kg * Payload: 14,320 kg Other: * German vehicle * 1 previous owner * Safety inspection 11 / 2025 ---- 2-axle HGE three-way tipper grain trailer TYPE: AK 18-3 VIN: 1HA0179 First registration: 17.02.2010 Chassis / Attachments: * 2 x SAF axles with disc brakes * Air suspension * Raise/lower, front + rear * Tyres: 385/55 R22.5 * Remaining tread: front approx. 20%, rear approx. 40/50% * Alloy wheels * 2 x PVC toolboxes Body: * HGE grain three-way tipper * Standing platform with access ladder on right * Sliding tarpaulin * Load area: 7,100 mm x 2,460 mm x 2,350 mm * Approx. 40 m³ * Drop sides 800 mm * Folding central stanchion * Internal tarpaulin for bulk cargo * Grain discharge chute Weights: * Gross vehicle weight: 18,000 kg * Payload: 13,770 kg * Unladen weight: 4,230 kg Other: * 1 previous owner * German vehicle * Safety inspection 10 / 2025 * New brake discs, new pads + 1 caliper front axle 08 / 2025 ----- New general inspections / safety checks or changes to gross vehicle weight (downgrading/upgrading) are available on request. We are happy to assist you with obtaining export/transit license plates, as well as arrange transport of your purchased vehicles within Germany. Contact us! We speak German, English, and Russian! No liability for typographical or printing errors. Subject to changes, interim sale, and errors! Who are we? Leible Nutzfahrzeuge is a family-owned company based in Kehl am Rhein. With many years of experience in the preparation and sale of commercial vehicles, we are a reliable partner for customers worldwide. Our special strength lies in the trade of new and used commercial vehicles. On 11,000 m², a wide range of vehicles is available. Our company philosophy is characterized by fairness and integrity. As customer satisfaction is very important to us, we offer our customers an excellent all-round service package and provide a competent contact person to assist you in purchasing or selling vehicles. See for yourself! Our service for you: Loading of vehicles We gladly assist you in loading your purchased vehicles. Arranging special transports We gladly help you organize special transports. Temporary/export license plates We are happy to assist you in obtaining export/short-term plates. Customs formalities We gladly assist you with customs procedures.

Condition: used, mileage: 656,928 km, power: 331 kW (450.03 HP), first registration: 05/2017, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, brakes: retarder, color: green, gearing type: automatic, emission class: euro6, total width: 2,550 mm, total height: 4,000 mm, loading space volume: 41 m³, loading space length: 7,100 mm, loading space width: 2,460 mm, loading space height: 2,350 mm, Year of construction: 2017, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, Scania R 450 LB 6x2*4 MSA VIN: 9224161 Chassis / Attachments: * Wheelbase: 4,600 mm / 1,350 mm * Leaf / air suspension * Lift axle // steering axle * Tyres: 1st axle 385/55 R22.5, 2nd + 3rd axle 315/70 R22.5 * Tread depth remaining: Front approx. 20/30%, Middle approx. 40/70%, Rear approx. 80/30% * 1 x aluminium tank 500 L * 1 x AdBlue tank * 1 x hydraulic tank * 1 x Bawer stainless steel toolbox Cab: * CR 19 H Highline * 2 x bunks * Automatic climate control * Auxiliary heater * Refrigerator * Radio CD // CB radio * USB, AUX, BT * Navigation system * Distance control Bodywork: * HGE grain tipper * Standing platform * Rolling tarpaulin * Side walls 800 mm * Foldable central stanchion * Internal tarpaulin * Body dimensions: 7,100 mm x 2,460 mm x 2,350 mm * Load volume: approx. 40 m³ * Grain slider Engine / Transmission: * 12,742 cc // 450 HP / 331 kW // EURO 6c * Opticruise / automatic transmission * Scania retarder * Differential lock Weights: * Gross vehicle weight: 26,000 kg * Unladen weight: 11,680 kg * Payload: 14,320 kg Other: * German vehicle * 1 previous owner * Safety inspection valid until 11 / 2025 ----2-Axle HGE Three-Sided Grain Tipping Trailer TYPE: AK 18-3 VIN: 1HA0179 First registration: 17.02.2010 Chassis / Attachments: * 2 x SAF axles with disc brakes * Air suspension * Raise/lower function, front and rear * Tyres: 385/55 R22.5 * Tread depth remaining: front approx. 20%, rear approx. 40/50% * Aluminium rims * 2 x PVC toolboxes Bodywork: * HGE grain three-way tipper * Standing platform with access ladder (right) * Rolling tarpaulin Nkedpfxjw H E E So Ad Njt * Load area: 7,100 mm x 2,460 mm x 2,350 mm * approx. 40 m³ * Side walls 800 mm * Foldable central stanchion * Internal tarpaulin for bulk cargo * Grain slider Weights: * Gross weight: 18,000 kg * Payload: 13,770 kg * Unladen weight: 4,230 kg Other: * 1 previous owner * German vehicle * Safety inspection valid until 10 / 2025 * New brake discs, new pads + 1 front axle brake caliper 08 / 2025 ---- New main inspections / safety checks or changes in permitted gross weights (reduction/increase) are possible upon request. We are happy to assist you in obtaining export/temporary registration plates and can arrange the delivery of your purchased vehicles within Germany. Contact us! ---- We speak the following languages: German, English, and Russian! ---- No liability for printing or typographical errors. Subject to change and prior sale. Errors excepted! ---- Who are we? Leible Nutzfahrzeuge is a family-owned company based in Kehl am Rhein. With our long-standing experience in the reconditioning and sales of commercial vehicles, we are a reliable partner for customers worldwide. Leible Nutzfahrzeuge's particular strength lies in the sales of new and used commercial vehicles. On 11,000 m² you will find a wide variety of vehicles. Our corporate philosophy is characterized by fairness and integrity. As customer satisfaction is very important to us, we offer our customers an outstanding full-service package and provide them with a competent contact person to assist them in purchasing or selling vehicles. See for yourself! Our services for you: Loading vehicles We are happy to help you load your purchased vehicles. Organizing specialist transport We are happy to assist you in organizing specialist transport. Temporary/export licence plates We are happy to help you obtain export or temporary registration plates. Handling customs formalities We are happy to assist you with cust

Condition: excellent (used), Year of construction: 2023, functionality: fully functional, NET WEIGHING FILLING SYSTEM TYPE TOPLINE 1200 Reaching hourly capacities of 1200 bags (ONE THOUSAND TWO HUNDRED BAGS/HOUR), the TOPLINE has been designed to meet the requirements of high-speed filling of open mouth bags. In combination with our high-capacity NET WEIGHER, the TOPLINE 1200 is the perfect machine for fully automatic filling of granulated products. The bags are singled and opened by rotating grid singling system. After filling through flap-filling spout, the bags are transferred to the bag closing system by upper belt guiding. For clean and dust-reduced transport of the bags, the bags are kept shut until they reach the bag closing system. The machine was purchased directly from Behn + Bates in 2023 used for about 4 months. The machines construction is 2015-17 but was idle at another customer and returned to Behn + Bates. In the Year 2023, the nearly new machine was fully upgraded to current and latest technology at Behn + Bates factory in Germany then put in production in France. New machine costs EUR 400,000+ with 9-18 months lead time. This is a great opportunity to buy at discounted price and available immediately! Video in operation available upon request. Machine Technical Data: - Electric power 17 kW - Compressed air 160 ltr./bag plus 18 m³/h at 5 bar overpressure - Dedusting air 1.750 m³/h at 10 mbar under pressure - Weighing range 10 - 52 kg adjustable in 50 gm steps - Operation 1 person for the operation of the plant and for manual supply of the bags into the magazine - Output up to 1,200 bags/h Bag - Product Specifications: - Bag type flat open mouth bags AND gusseted open mouth bags - Flat Open Mouth Bag width 400 mm – 600 mm & Bag length 550 mm – 1000 mm - Gusseted Open Mouth Bags 380 mm – 600 mm (min. 320 mm between gussets) & Bag Length 550 mm – 1000 mm - Product examples crystal sugar, rice & grain, seed, dehydrated vegetables, animal feed & pet food, etc. Characteristics
Diagnosis and functional test of the inputs and outputs
Touch panel with integrated troubleshooting
Electronic weighing system MEC Nodpfeyah R Aox Ad Nokt
Dosing time regulator
Product contacting parts made of stainless steel
Central dedusting connections
Empty bag magazine with space for 5 bag bundles
Rotating grid singling system
Bag singling and opening by vacuum
Radial inlet flap with servo drive
Double bottom flaps
Three load cells
Flap-filling spout with internal deaeration
Liftable bag bottom vibrator
Full bag transfer by upper belt guiding Your benefits
High capacity
High weighing accuracy
Easy cleaning
Compact filling system
Easy palletizing due to perfectly shaped bag bottom
High filling degree and good product compaction due to bag vibrator
Intermittent bag transfer at the top of the bag = bags kept shut
Integrated electric control panel = quick assembly
Clean packaging area due to the encapsulated system
Lockable inspection doors on both the weigher and flap inlet
Easy product change

Condition: new, empty load weight: 2,980 kg, maximum load weight: 8,920 kg, overall weight: 11,900 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, suspension: steel, tire size: 245 / 70 R 17,5, color: other, gearing type: other, front tire size: 245 / 70 R 17,5, rear tire size: 245 / 70 R 17,5, driver cabin: other, emission class: none, Equipment: ABS, compressed air brake, Three-way tipper, loading height approx. 940 mm, front wall foldable for overloading, central locking for side and rear drop sides, automatic rear wall opening during reverse tipping, side walls pendulum-mounted and foldable, side drop sides with spring relief, platform floor made of 4 mm fine-grained steel, 8 heavy-duty recessed lashing rings in the floor, 5-stage hard-chromed three-way tipping cylinder, tipping angle: 50 degrees to the rear, 45 degrees to the side, stepless height-adjustable drawbar, removable stakes at the rear, gear support winch with load and quick mode in front, integrated storage compartment for two aluminum loading ramps in the chassis, lockable ramp compartment (privacy cover), contour marking according to ECE R 048 regulation, vehicle with day registration, rental price from €550. Typing errors, mistakes and changes reserved, sample images. More data at: !, More details: ! Nkedpfxox S N Axj Ad Njt

Condition: new, empty load weight: 2,980 kg, maximum load weight: 10,020 kg, overall weight: 13,000 kg, axle configuration: 2 axles, loading space length: 5,110 mm, loading space width: 2,430 mm, suspension: steel, color: other, gearing type: other, driver cabin: other, emission class: none, Equipment: compressed air brake, Three-way tipper, body side panels hot-dip galvanized, loading height approx. 940 mm, front panel foldable for overloading, central locking system for side and rear boards, automatic rear board opening when tipping backwards, side panels can swing and be folded down, side panels with spring assistance, platform floor made of 4 mm fine-grained steel, 8 high-strength recessed lashing eyes in the floor, 5-stage hard-chromed three-way tipping cylinder, tipping angle: 50 degrees to the rear and 45 degrees to the side, continuously height-adjustable drawbar, removable rear stakes, gearbox-mounted support winch with load and quick modes at the front, integrated compartment in the chassis for two aluminum loading ramps, lockable ramp compartment (privacy protection), contour marking in accordance with ECE R 048 regulation, Rental price from €550, -- Errors, omissions and changes reserved, sample pictures --, More data at: !, More details: ! Nksdpfx Asx S N Afed Nst

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2011, power: 650 kW (883.75 HP), Woodchips fueled air heater. For grain kilns or industrial halls. Fully automatic with ignition. Have wery low hours- used only 2 seasons. Last 11 years stayd in dry room. Nodpfx Adowxq D Ro Nskt Hydraulically driven grates for best burning process. Has hydraulically driven storage, fan and all includings. Automatical ash conveying.