Used Grain for sale (705)

Condition: new, functionality: fully functional, machine/vehicle number: WFDFLT33801013475, empty load weight: 7,180 kg, maximum load weight: 28,820 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, color: silver, available in multiple units Fine-grained steel welded construction, kingpin plate with replaceable 2" kingpin, additional splash guard riveted to the underside as a sheet of metal, in the neck area above the rear axle of the semi-trailer and above the wheels on the vehicle, frame in reinforced design for vehicle loads up to the outer frame, outer frame with "Load-Lock profile" approximately every 400 mm for securing lashing straps, 10 pairs of lashing rings embedded in the top/outside of the outer frame, each rated at 10 tons, 24 tons. Two-stage support winch, single-side operation, with semi-circular lower part and straight connecting plate, with stroke compensation, folding rear support, support wedges with holder, aluminum side impact protection, steel under-ride protection, quarter panel fenders in front of and behind each axle, with additional sheet metal splash guard above the wheels, with anti-spray flaps according to EC regulations, 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable, container locking system, 4 pairs of locking recesses embedded in the floor for 2 x 20 ft or 1 x 40 ft containers, 4 pairs of container locking adapters, (additional transverse support required at the front and rear of the container, the container must rest evenly over its width in conjunction with the locks, transverse supports are not included in the scope of delivery), attachment rail for loading ramps at the rear extension over the entire width, rear extension mechanical, with hand crank, extendable by approximately 1,500 mm, lockable every 500 mm, including under-ride protection with lighting that can be extended, in the wheel well area with Lohr sheet metal, center with steel diamond plate, storage space for loading ramps integrated in the rear extension, usable only when the rear extension is extended by approximately 1000 mm, for transporting the ramps with the rear extension retracted - storage space for ramps in the FR, located to the right in front of the axles. 1 pair of ramps, 3,000 mm long, 300 mm wide, load-bearing capacity per pair 6,000 kg, electric cable winch, 24 volts, pulling force approximately 8165 kg, mounted centrally at the very front, operated with a wireless remote control, cable length 35 m x approximately 10 mm, with roller cable guide and removable guide rollers. Axles + Suspension: SAF/BPW drum brake axles, at the manufacturer's choice, air suspension, 1st axle automatic lift axle, additionally electrically operable from the truck, including forced lowering and starting aid. Bsdpfjza Aiysx Amrjwu Braking System: 2-line pneumatic braking system, color-coded line routing for easy servicing, spring-loaded parking brake, 2 tamper-proof coupling heads at the front, EBS, electronic braking system with EBS socket at the front, without connection cable, with raising & lowering valve with quick vent, holding function in lowered position + auto-reset function, vehicle stability system, axle load recognition via EBS-CAN bus signal. Wheels and Tires: 235 / 75 R 17.5", manufacturer's choice, steel rims in twin arrangement. Electrical System: 24 volts, multi-chamber lights in LED, yellow LED lighting on the side, license plate lighting in LED, 2 white position lights at the front in LED, 2 white/red side marker lights at the rear in LED, 2 x 7-pole and 1 x 15-pole tamper-proof sockets at the front, 2 additional LED work lights at the rear, 1 rotating beacon with holder, switched via parking lights, 2 pairs of warning signs, double LED illuminated and

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 6,950 kg, maximum load weight: 23,050 kg, overall weight: 30,000 kg, axle configuration: 3 axles, loading space length: 7,500 mm, loading space width: 2,520 mm, total length: 9,350 mm, total width: 2,550 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Chassis – Central axle trailer design Fine-grained steel welded construction Gear-supported front leg Hydraulic rear supports Wheel chocks with holder Aluminum side impact protection Without under-run protection Mud flaps at the rear, covering the entire width Mud flaps in front of each axle and anti-splash mud flaps behind each axle Plastic tool box, with insert, w=620/h=360/d=440 mm, lockable with a padlock Extendable widening elements to 3,000 mm Storage compartment for wooden planks in the center + wooden planks 70 mm for widening to 3,000 mm Tie-down points for low-bed trailers Recessed ring-type tie-down points in the outer frame, each rated at 5 tons (can be converted to stake pockets) Tie-down eyes at the top and on the sides in the outer frame, each rated at 10 tons Towing device – Central axle trailer Drawbar with a tested 50 mm tow hitch Axles + Suspension Drum brake axles "Axles/chassis laser-aligned" – reduces tire wear and fuel consumption Last axle with trailing arm steering, with automatic reversing lock controlled via the reversing light, and an additional locking function on the vehicle via a manual button. Air suspension 1st axle – automatic lift axle, additionally manually lowerable, operable with a button on the vehicle Axle lift below the recommended driving height, therefore no guarantee for tire damage Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, with connection lines to the towing vehicle EBS, electronic braking system with EBS connector at the front, with connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle height in conjunction with the lift axle; when the lift axle is raised, the loading or overall height increases by 50 mm Vehicle – Driving stability system Trailer Info Center for displaying vehicle data such as axle loads, mileage, and diagnostic/system messages Axle load detection via EBS-CAN bus signal for display on the display in the cab Wheels and tires 235/75 R17.5, manufacturer's choice Steel rims, factory silver Electrical system 24 volts, multi-chamber lights in LED with resistor, yellow LED lighting on the sides, license plate lighting in LED 2 white position lights at the front in LED 2 white/red marker lights at the rear in LED 2 x 7-pin fail-safe plugs at the front, with connection cable Bwjdpfx Amjzcv D Norsu Additional LED work light at the rear LED rotating beacon with mount Warning signs, LED illuminated and extendable to 3,000 mm Floor Subsequently with 70 mm softwood flooring, steel/diamond plate covering in the wheel arch area Rear slope with 70 mm softwood flooring Low-bed platform including rear slope 7,500 mm Ramps Steel ramps, 2,800 mm long, 750 mm wide, laterally adjustable Covered with wood Hydraulically operated via towing vehicle’s auxiliary drive with throttle, operation on the left side in the front Hydraulic lateral adjustment of the ramps, individually controllable Hydraulic connection with quick-release coupling NW 10/3, including connection hose Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,120 mm, suspension: air, tire size: 385/55 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle swap trailers Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable Pair of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front gear-driven support legs, with straight lower section and single-sided operation on the right side 1 pair of rear gear-driven support legs, with straight lower section and single-sided operation on the right side Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Towing beam clamped/bolted, easily replaceable and partially adjustable in length! Lower coupler on towing beam, free towing beam length approx. 2200 mm Folding bracket with spring support on the towing beam, for routing the connection cables to the truck *Axles + Suspension SAF disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Air suspension without lift axle Bwodpfx Aezd Trremreu *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake while coupled; EBS power supply must be ensured! *Wheels and Tires 385/55 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lighting, LED license plate lighting, (Note: With certain towing vehicles, false diagnostics may occur even though the function is working properly) 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection on the right rear Additional LED work light(s), recessed and integrated into the rear, activated via the reverse light LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 ADR warning sign at the rear, foldable Contour marking with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,250 kg, maximum load weight: 14,750 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 10,020 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with central-axle trailer Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15 m, 7.45 m, and 7.82 m swap bodies (Note: When used in combination with the impact guard, the guard protrudes beyond the 7.15 m swap body) 1 pair of front transmission support legs, with straight lower section and single-side operation on the right rear 1 pair of transmission support legs at the rear, with straight lower section and single-side operation on the right side 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection Rear mud flaps across the entire width Half-shell fenders Mud flaps *Towing Equipment for Central-Axle Trailers Towing beam with certified 50 mm tow eye, freight carrier version Flat flange plate for tractors with a clearance-type low-bed trailer, connected to the towing beam at the top and bottom Bwedpfx Amjzd Udcereu Towing beam clamped/bolted, easily replaceable, and partially adjustable in length! Lower coupler drawbar, free drawbar length approx. 2200 mm Fold-down bracket with spring assistance on the drawbar, for routing the connection cables to the truck *Axles + Suspension BPW disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake system 2-line compressed air brake system Color-coded wiring for easy servicing. Air reservoir: 208 liters Air-spring parking brake, Control panel at the rear right Duomatic connection at the front, with connecting line to the tractor unit, connection at the rear right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection at the rear right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift and lower valve, hold function in both lower and lift positions Vehicle - Vehicle Stability Control System *Wheels and Tires 385/65 R22.5" Manufacturer's choice Steel rims, factory silver *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting Connectors for electrical and air connections on the drawbar 2 white front position lights 2 white/red rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, connection at FR-right 2 additional LED work lights, recessed and integrated into the rear, activated via the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated via the reverse light *Country of Registration/License Plates Germany With DEKRA approval and certification (per §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Warning sign per ECE - 70 Night parking sign front and rear Contour markings with reflective strips in accordance with ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,100 kg, maximum load weight: 14,900 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,970 mm, total width: 2,550 mm, total height: 1,250 mm, suspension: air, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis for central-axle trailer Fine-grained steel welded construction Front stop, transverse, in a foldable/adjustable design, as previously delivered with AU 257359 1 pair of removable guide rollers, front and rear 1 additional pair of removable guide rollers 4 container locks with sturdy arms based on 20" for swap bodies 7.45 m and 7.82 m 1 pair of front transmission support legs, with straight lower section and single-side operation on the right side Bedpozd U I Ujfx Amrswu 1 pair of rear transmission support legs, with straight lower section and single-side operation on the right side (FR) Side impact protection set inward, for optimal clearance to the swap body supports Steel underrun protection *Towing equipment for central-axle trailers Towing beam with certified 50 mm tow eye, freight forwarding version Flat flange plate for tractors with underrun-protected LBW, connected to the drawbar at the top and bottom Drawbar clamped/bolted, easily replaceable and partially adjustable in length! Under-coupler drawbar, free drawbar length approx. 2150 mm Folding bracket with spring support on the drawbar, for routing the connection cables to the truck *Axles + Suspension SAF or BPW disc brake axles “Laser-aligned axles/chassis” reduces tire wear and fuel consumption Travel odometer/odometer Air suspension *Brake System 2-line compressed air brake system Color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake, Control panel in the front right Duomatic connection at the front, with connecting line to the tractor unit, connection in the front right 24-volt EBS, electronic braking system with EBS connector at the front, with connecting cable, connection in the front right Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve, hold function in both lower and lift positions Vehicle – Vehicle Stability Control System Brake release function via a pushbutton on the vehicle next to the lift & lower valve, for releasing the brake when coupled; EBS power supply must be ensured! “TPMS” Tire Pressure Monitoring System according to ECE R 141, display in the towing vehicle via EBS *Wheels and Tires 385/65 R22.5" steel rims, factory silver *Electrical System 24 volts, multi-chamber LED lights, yellow LED side lights, LED license plate lights, (Note: With certain towing vehicles, false diagnostic errors may occur even though the system is functioning properly) Yellow LED side lights linked to the turn signals “Flashing side lights” Parking sockets for electrical and air connections on the drawbar 2 white LED front position lights 2 white/red LED rear lane-keeping lights 1 x 15-pin connector at the front, with connecting cable, located on the right rear 2 additional LED work lights, recessed and integrated into the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Prepared for single-line license plate holder Night parking sign at front and rear *Paint Finish Frame Hot-dip galvanized or painted according to customer preference

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 2,500 kg, maximum load weight: 15,500 kg, overall weight: 18,000 kg, axle configuration: 2 axles, total length: 9,470 mm, total width: 2,550 mm, total height: 1,260 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. *Chassis with swivel turntable Fine-grained steel welded construction Fliegl “V-Stream” frame Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy 20"-based arms for 7.15- and 7.45-meter swap bodies Note! Not suitable for 20" containers, or only possible if the container has a tunnel or opening at the front center approximately 200 mm long and 800 mm wide! Swivel frame with heavy-duty ball bearing swivel ring 2 wheel chocks with holders Aluminum side impact protection Side impact protection set inward for optimal clearance to the swap body supports Steel underrun protection Underrun protection shortened for optimal clearance to the swap body supports; lighting system mounted in a protected position Half-shell fenders Rear mud flaps across the entire width *Trailer Coupling Device (Turntable) Towing fork with certified 40 mm tow eye Spring-loaded towing fork height adjustment *Axles + Suspension SAF disc brake axles “Laser-measured axles/chassis” reduces tire wear and fuel consumption Air suspension *Brake System 2-line compressed air brake system; color-coded lines for easy servicing. Air reservoir: 208 liters Spring-loaded parking brake 2 non-reversible coupling heads at the front, with connecting lines to the tractor unit, EBS, Electronic Brake System with EBS connector at the front, with connecting cable, Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift/lower valve, hold function in both lower and lift positions *Wheels and Tires 385/65 R22.5" Manufacturer’s choice Steel rims, factory silver, ET 120 *Electrical System 24 volts, multi-chamber lights, yellow LED side lighting 2 white front position lights 2 white/red rear lane-keeping lights Bjdpfezd U Uusx Amrewu 2 x 7-pin reverse-proof connectors at the front, with connecting cable, 2 additional LED work lights at the rear, activated by the reverse light 1 LED work light at the front, centered between the cross members, shining toward the rear, activated by the reverse light *Country of Registration/License Plates Germany with DEKRA approval and certification (in accordance with §13 EG - FGV) 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective strips per ECE R 048, white on the sides and red at the rear *Paint finish Frame Hot-dip galvanized or painted according to customer specifications Customized transport solution Configure your Fliegl vehicle to meet your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications.

Condition: used, machine/vehicle number: WFDFLT33802021791, empty load weight: 6,433 kg, maximum load weight: 28,567 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 11/2017, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 3,000 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 445/45 R19,5", color: black, Please note: The images shown are archive photos. The vehicle may still be in operation. ## Fliegl Mega Curtainsider Semi-Trailer Chassis: Lightweight fine-grain steel chassis, replaceable 2" kingpin, Load-Lock outer frame, 24 t JOST two-speed landing gear, rear access ladder, door retainers, aluminium side underrun protection, galvanised rear underrun protection, quarter mudguards, anti-spray mud flaps, Heavy Blocker rear impact protection with side roller buffers, heavy-duty pallet stop, spare wheel carrier, lockable toolbox with drawer, document box. Axles & Suspension: BPW drum brake axles (8-stud hubs), laser wheel alignment, mechanical hubodometer, air suspension, automatic lift axle with forced lowering and traction aid (activated by brake pedal or manual switch). Brakes: Dual-line air brake system, spring parking brake, WABCO EBS, lift/lowering valve. Raising the lift axle increases loading/overall height by approx. 50 mm. Tyres: 445/45 R19.5 (manufacturer's choice). Electrical: 24 V LED lighting, LED side markers, LED front position lights, LED rear outline lights, 2 × 7-pin and 1 × 15-pin front sockets. Floor: Approx. 30 mm plywood floor with Omega-reinforced joints, suitable for forklift axle loads up to 7,100 kg. Front Wall: 2,580 mm high, steel corner posts, curtain release system, internal steel impact protection, additional 1,250 mm plywood lining. Bwedjzlciispfx Amrju Centre Posts: 3 pairs of full-length sliding posts with multiple locking positions. Side Slats: Aluminium or timber V-slats. Rear: Steel rear corner posts, double rear doors with internal locking bars, curtain tensioning system. Curtains: Reinforced curtains with welded horizontal and vertical straps, stainless steel buckles. Roof: Sliding roof, rear end lift, automotive L-roof rails, hydraulic lifting roof on both sides (+400 mm), rain gutter at rear. Certification: DEKRA approval, EN 12642 XL load securing certificate, VDI 2700 Sheet 12 beverage transport certification, ECE R70 rear warning plate.

Condition: used, machine/vehicle number: WFDFLT21601003373, empty load weight: 2,600 kg, maximum load weight: 10,800 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 11/2013, total length: 5,200 mm, total width: 2,550 mm, tire size: 285/70 R19,5", color: grey, 4 UNITS AVAILABLE! – 4 UNITS AVAILABLE! – 4 UNITS AVAILABLE! – 4 UNITS AVAILABLE! Conversion to CLG dolly in progress – some units already completed. Please note: The photos shown are archive images and may differ from the actual vehicle. # Chassis Heavy-duty fine-grain steel welded construction Fifth wheel coupling (manufacturer of our choice) for 2" kingpin with ball-bearing turntable, steering angle max. 20° Telescopic landing leg 2 wheel chocks with holders Steel rear underrun protection Half-shell mudguards CLG drawbar with certified 50 mm towing eyes for connection to both the dolly and the towing truck. # Axles + Suspension BPW disc brake axles Air suspension with raise/lower valve # Brake System Dual-line compressed air braking system Spring parking brake 2 non-interchangeable air couplings at the front with connecting lines to the towing vehicle 2 non-interchangeable air couplings for the semi-trailer Electronic Braking System (EBS) with front EBS connector and connecting cable EBS connection cable for the semi-trailer Axle load detection for the truck via EBS Note: The trailer may only be operated with towing vehicles that ensure full ABS functionality. # Electrical System 24 V electrical system Multi-chamber lighting Yellow LED side marker lights 2 white LED front position lights 2 white/red LED rear outline marker lights 1 × 15-pin connector with cable to the towing vehicle 1 × 15-pin connector with cable to the semi-trailer # Registration Prepared for registration in Germany DEKRA approval included Prepared for single-line number plate holder Bjdezm Trqopfx Amrewu ECE R48 reflective contour markings (white sides, red rear) # Dimensions Fifth wheel height: approx. 1,150 mm Drawbar coupling height: approx. 380 mm Archive photos – actual vehicle may vary.

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 5,700 kg, maximum load weight: 33,300 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 7,700 mm, loading space width: 2,350 mm, loading space height: 1,600 mm, loading space volume: 31 m³, total length: 9,090 mm, total width: 2,550 mm, total height: 3,110 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. More information Chassis, saddle, and tipper Fine-grained steel welded construction, in basic lightweight design, saddle plate with interchangeable 2 king pin Curved front panel, patented 24 tons, 2-stage support winch, single-sided operation, with straight lower part, without extension compensation Chocks with holder Rear underrun protection, foldable Semi-shell mudguards Integrated mudguard holder, surface designed to repel stones With anti-splash flaps, only on the last axle Tarpaulin rod with holder Towing hook at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned, reduces tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Brake system 2-line compressed air brake system, color-coded lines for easy service Spring-loaded parking brake 2 fail-safe coupling heads in the front, without connection line EBS, electronic brake system with EBS socket in the front, without connection cable Note: The trailer may only be pulled by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only on standard tires). Electrical system 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides, linked to the turn signal ("flashing side lights") 2 x 7-pole fail-safe sockets in the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw sleeve, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Dump body Steel round dump body in "Stone Master Design" made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic cylinder mount. Inside with access ladder on the front wall. Greenline - conical and aerodynamic dump body shape Bwodpfx Amei Rivdjrou Shovel and broom holder on the outside of the front wall Membrane - rear wall Rear wall as a pivoting flap with double-hinge hinge, externally mounted with double hook lock. 2 clamping screws with toggle closures on the lower side. Side walls continuously 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized construction Standing platform with access ladder, connection plate for air/electrical and brake connections with ample space for the best possible operation. Rollover cover on one side for storage on the right-hand side, with central locking on the left-hand side Country of registration/plates Germany Type approval according to EC 2007/46 Superstructure strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single-line Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Paint finish Frame DB 7350 Novagrau "10-year warranty against rust-through" Support legs, black coated Dump body, RAL color of your choice, single color Rollover cover,

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 30,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,470 mm, loading space height: 2,150 mm, loading space volume: 38 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,740 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements. Bedpfoi Riz Rox Amrjwu Chassis, Saddle Tipper Fine-grained steel welded construction, lightweight design, saddle plate with 2 interchangeable kingpins Curved front end, patented Telescopic support in the center, uncoupling not possible with load, in the uncoupled state, the vehicle must be tilted backwards. 2 chock blocks with holder Underrun protection, foldable Semi-shell fenders Integrated fender holder, surface resistant to stone chipping With anti-splash flaps, only on the last axle 1 tarpaulin rod with holder 2 towing hooks at the rear Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid, actuated 3 times by the brakes Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front EBS, electronic braking system with EBS socket at the front With lifting and lowering valve Vehicle - Driving Stability System Wheels and Tires 385/65 R22.5, manufacturer at the discretion of the manufacturer Steel rims, factory silver Electrical System 24 volts, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 2 x 7-pole non-interchangeable sockets at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard chrome-plated, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Actuation hydraulically via truck auxiliary drive Tippers Aluminum box tipper made of high-quality, abrasion-resistant steel, front wall 5 mm thick, with external stiffeners made of 30 mm hollow profile, cleanly welded, with an upper profile that prevents spillage. Inside with ladder on the front wall (not in conjunction with Cramaro). Shovel and broom holder outside on the front wall. Greenline - conical and aerodynamic tipper body shape Membrane - rear wall Rear wall as a hinged flap with double-joint hinge, externally supported with 2-fold hook locking. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor continuously 6 mm thick Standing platform with ladder, connection plate for air/electrical and brake with large clearance for best possible operation. Roller cover, one-sided for placement on the right side, with central locking on the left side Painting Frame DB 7350 Novagrau 10 years Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer requirements.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 33,100 kg, overall weight: 38,000 kg, axle configuration: 3 axles, total length: 7,450 mm, total width: 2,550 mm, suspension: air, tire size: 385/65 R22,5", tire condition: 100 %, Customized Transport Solution Bwedpfxoi Ri Ave Amrou Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Chassis, Saddle, and Container Fine-grained steel welded construction, saddle plate with 2 interchangeable kingpins and 2 kingpin positions. Front locking on tipper ram mount with bilateral tapered wedges, rear locking on continuous swivel shaft with return spring. Container mounts: Locking crossmember, 2-fold for locking 1 x 20 ft or 1 x 30 ft container. Adjustment via central telescope as an interlocking central tube frame with bolt locking. 24 ton, 2-stage support jack, single-sided operation, with straight lower part, without thrust compensation. Free support foot angle or free swivel radius to the rear approx. 1850 mm. 2 chock blocks with holder. Half-shell mudguards with anti-splash flaps according to EC standards. Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard chrome-plated, with HDK screw fitting, fixed part, NW 48 mm. (without hose connection) Actuation hydraulically via truck auxiliary drive. Hydraulic connection with hose and HDK screw connector NW = 48 mm with knurled nut. Axles + Suspension SAF disc brake axles with 430 mm disc diameter. Axle/chassis laser-aligned, reducing tire wear and fuel consumption. Axle spacing offset mm (combined transport) up to 44 tons total weight. Air suspension Braking System 2-line compressed air braking system Color-coded line routing for easy servicing. Spring-loaded parking brake Tele Control Axle load reduction for easy telescoping. 2 fail-safe coupling heads at the front, without connecting line. EBS, electronic braking system with EBS socket at the front, without connecting cable. Note: The trailer may only be towed by tractor units that guarantee the effectiveness of the ABS! With lifting and lowering valve. Vehicle - Driving Stability System Axle load detection via EBS-Canbus signal, for display on the instrument panel in the driver's cab; the truck must be pre-equipped accordingly, no truck installation. Wheels and Tires 385/65 R22.5, manufacturer's choice. Steel rims, factory silver. Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the side. 2 white position lights at the front. 2 white/red marker lights at the rear. 2 x 7-pole fail-safe sockets at the front, without connecting cable. Additional LED work light at the rear, switched via reversing light. Country of Approval / Signs Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for license plate holder, single-line. Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear. Paintwork Frame DB 7350 Novagrau (dark gray) 10-year warranty against rust-through. Support legs, black coated. Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,200 kg, maximum load weight: 33,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,600 mm, loading space volume: 27 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,110 mm, suspension: air, tire size: 385/65R22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. Further Information Chassis, Saddle, and Tipper Fine-grained steel welded construction, in basic lightweight design, saddle plate with interchangeable 2 kingpins Curved front end, patented Telescopic support in the center, uncoupling with load is not possible; when uncoupled, the vehicle must be tilted backward. Chocks with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to repel stones Tarpaulin rod with holder Towing hook at the rear Axles + Suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Axles in off-road design Air suspension 1st axle: automatic lift axle, including forced lowering and starting assist Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lift and lower valve Vehicle - Driving Stability System Wheels and Tires 385/65 R22.5 Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via the towing vehicle, via EBS, without truck installation (this must be possible in the truck. Only for standard tires). Electrical System 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side, linked to the turn signal ("flashing side lights") 2 white position lights at the front 2 white/red outline lights at the rear 2 x 7-pole fail-safe sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chrome plated, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Actuation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinder with access ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder on the outside of the front wall. Bwodpfoi Ri A Iox Amrou Membrane - rear wall Rear wall as a swing flap with double-hinge, externally supported with 2-fold hook lock. 2 clamping screws with cam locks on the side at the bottom. Side walls continuously 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized design Standing platform with access ladder, connection plate for air/electrical and brake connections with large clearance for the best possible operation. Roll-over tarpaulin on one side, to be placed on the right, with central locking on the left Registration country / signs Germany Type approval according to EG 2007/46 Body strength according to EN 12642 24/7 service hotline prepared for single-row license plate holder Warning sign according to ECE - 70 Contour marking with reflective strips according to ECE R 048, white on the side and red at the rear Painting Frame: DB 7350 Novagrau "10-year warranty against rust-through" Support legs: galvanized Body: RAL color of your choice, solid color Roll-over

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 7,500 kg, maximum load weight: 18,700 kg, overall weight: 26,200 kg, axle configuration: 2 axles, total length: 12,400 mm, total width: 2,550 mm, tire size: 205 / 65 r 17,5, Additional Information Chassis, Saddle, Haulage Company Fine-grained steel welded construction, saddle plate with 2 replaceable kingpins, rear slope to approx. 1920 mm, continuous lashing rail for ramps at the rear and front on the gooseneck, sliding rollers at the rear, low-bed to the axle group after the slope. Drawing approval required from the customer in case of an order! Pair of lashing points recessed in the outer frame at the top and side, 10 tons each. Pair of lashing eyes recessed in the outer frame on the gooseneck, 5 tons each. 24-ton, 2-stage support winch, single-sided operation, with straight lower part, without stroke compensation. Foldable rear support, mounted externally. Wheel chocks with holder. Aluminum side impact protection. Bwjdpfei Ri Hrex Amrsu Steel underrun protection for EC, if technically possible. Quarter panel fenders. With anti-spray flaps according to EC. 1 pair of wheel recesses recessed in the low-bed area after the gooseneck, sloped for entry. Length at the bottom approx. 1840 mm, depth of wheel recesses approx. 200 mm. 2nd pair of wheel recesses on the rear slope. Depth approx. 200 mm. Note: Frame in the main beam area is 200 mm higher than the wheel recess. A detailed technical review is still required in case of an order. Wheel recess cover retractable from the low-bed with hardwood inserts, on the rear slope with hardwood inserts. Electric winch, 24 Volt, pulling force 5500 kg, mounted in the slope of the gooseneck, does not reach into the loading area, operation with wireless remote control, rope length 35 m x approx. 10 mm, with roller rope guide and detachable guide roller on the rear slope. Axles + Suspension SAF or BPW drum brake axles at our discretion. Air suspension with lift and lower valve + auto-reset function. Wheels and Tires 205 / 65 R 17.5 tires with 129/127K (132/132G) marking for 8 tons tire load capacity at max. 90 km/h. At the manufacturer's choice. Steel rims in twin arrangement, factory silver. Braking System 2-line pneumatic braking system. Spring-loaded parking brake. 2 non-interchangeable coupling heads at the front, without connecting line. EBS manufacturer Haldex, electronic braking system with EBS socket at the front, without connecting cable (brake calculation sent to the customer for approval. 07/15/2021). Attention: The trailer may only be pulled by towing vehicles which ensure the effectiveness of the ABS! Axle load detection via EBS-CAN bus signal, for display on the display in the driver's cab, truck must be prepared accordingly, no truck installed (no calibrated scale). Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides. 2 white position lights at the front. 2 white/red marker lights at the rear. 2 x 7-pole and 1 x 15-pole non-interchangeable sockets at the front, without connecting cable. Floor Gooseneck with steel / checkered plate covering. 30 mm sieve floor, in the low-bed between the longitudinal beams in the middle. In the wheel track area covered with toothed grating, in the wheel recesses with steel / checkered plate covering. Ramps Pair of aluminum ramps 3,200 mm long, load capacity per pair 12,000 kg. Pair of steel ramps for entry into the low-bed. Pair of steel ramps for driving onto the gooseneck. Side boards Approval / Signs Country of registration: Germany With DEKRA approval and certificate (according to §13 EC - FGV). Prepared for single-row license plate holder. Contour marking with reflective strips according to ECE R 048, yellow on the

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 3,135 kg, maximum load weight: 8,665 kg, overall weight: 11,800 kg, axle configuration: 2 axles, loading space length: 6,200 mm, loading space width: 2,480 mm, total length: 8,350 mm, total width: 2,550 mm, suspension: steel, tire size: 235/75 R17,5", tire condition: 100 %, Customized transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Fine-grained steel welded construction Outer frame slightly inclined with "Load-Lock profile" for attaching lashing straps Gearbox support at the front Foldable rear support 2 wedge blocks with holder Underrun protection, steel, galvanized Splash guards at the rear, covering the entire width Partial wheel arches according to EC standards with anti-spray splash guards according to EC standards 1 plastic toolbox, w=600 / h=425 / d=460 mm, lockable Storage compartment for inserting bars, open, below the loading area 4 lashing/rail strips inserted crosswise in the floor, across the entire width up to the outer frame (max. usable internal width between the outer rail supports approx. 2170 mm), approx. 100 mm high. With 20 mm round steel strips at the top and bottom, spacing from top to bottom approx. 60 mm (of the round steel). At the bottom with an angle plate as a finish, open halfway down. For lashing and inserting 80 x 80 mm rails. 4 pairs of rail pockets inserted in the outer frame, internal dimension 83 x 83 mm 4 rail pockets inserted centrally in the floor, with reinforcements to the main frame, internal dimension 83 x 83 mm 6 pairs of insertion rails B=80/ D=80/ L=2000 mm, hot-dip galvanized Bsdpfx Amei Ri H Derswu Note: Rail pockets/insertion bars are not designed for the sole securing of long materials, pipes, etc. without wrapping. Side impact protection, aluminum Coupling device for tandem trailer Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 4 x 500 mm from 1800 - 3800 mm, drawbar length set to 1800 mm Axles + Suspension Axles according to the manufacturer's choice, with tapered roller bearings and S-cam brakes "Axle/chassis laser-aligned" Reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (lever compensation) Wheels and tires 235 / 75 R 17.5", according to the manufacturer's choice Steel rims, factory silver Braking system 2-line compressed air brake system Spring-loaded parking brake Integral air tank 2 fail-safe coupling heads at the front, with connecting lines to the towing vehicle, ABS and ALB, with ABS plug at the front, with connection cable Note: The trailer may only be pulled by towing vehicles which guarantee the effectiveness of the ABS! Electrical system 24 Volt, multi-chamber lights in LED, yellow LED lighting on the sides, license plate lighting in LED (Note! with certain towing vehicles, false diagnoses may occur, even if the function is given) 2 white position lights at the front in LED 2 white/red marker lights at the rear in LED 2 x 7-pole fail-safe plugs at the front, with connection cable Floor Sieve print plates approx. 30 mm thick, for high point load capacity Note: Floor deformation due to weather influences possible! Platform length approx. 6,200 mm Operating instructions Special permit required if the overall train length exceeds 18,750 mm. Observe country-specific registration regulations. Approval / Signs Registration country: Germany with DEKRA inspection and certificate Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame hot-dip galvanized incl. passivation "15-year warranty against rust-through" Customized transport solution

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,900 kg, maximum load weight: 34,100 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,300 mm, loading space width: 2,420 mm, loading space height: 2,150 mm, loading space volume: 49 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 4,040 mm, suspension: air, tire size: 385/65 r22.5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer needs. Further Information Chassis Fine-grain steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end, patented 24-ton, 2-speed landing gear, single-sided operation, with straight lower part, without push-pull compensation Wedge supports + holder Under-run protection, foldable Semi-shell fenders Integrated fender holder, surface repels stones Towing hook at the rear Axles + Suspension SAF disc brake axles Axle/suspension laser-aligned, reduces tire wear and fuel consumption Air suspension 1st axle: automatic lift axle, including forced lowering and starting assist, activated by 3x braking (starting assist functional up to an axle load exceeding 30% and a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line pneumatic braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 non-interchangeable coupling heads at the front, without connecting line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be pulled by tractor units that ensure the effectiveness of the ABS! With lifting and lowering valve Vehicle - Driving Stability System Wheels & Tires 385/65R22.5, manufacturer's choice Polished aluminum rim, manufacturer's choice Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pin socket at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw-on fitting, fixed part, NW 48 mm Actuation hydraulically via truck auxiliary drive Tippers Aluminum box tipper, sloping front wall, 5 mm thick, with external side walls made of 30 mm hollow profile, cleanly welded, with upper edge profile that prevents spillage of bulk goods. Interior with access ladder on the front wall Shovel and broom holder on the outside of the front wall Greenline - conical and aerodynamic tipper body shape Bwjdpfx Aoi Ri Idomrsu Membrane - rear wall Rear wall as a swing-open flap with double-joint hinge, externally mounted with 2-fold hook locking. Rear wall with rubber seal Note! Heat-resistant up to max. 170°C! Floor continuously 5 mm thick, Brinell 110 Note! Only for the transport of sand, gravel and rolled gravel with a maximum grain size of up to 20 mm! All other transported goods are excluded from the warranty! Standing platform with access ladder, connecting plate for air/electricity and brake with large space for the best possible operation. Roll tarp, single-sided for storing on the right-hand side (when facing forward), with central locking on the left-hand side (when facing forward) Operating instructions For the transport of salt, lime, etc., we recommend a tipping cylinder with a hard-chromed piston rod to protect against rust The specified total weight is technically possible, but depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor driving and handling behavior possible due to incorrect load distribution) Country of registration / Signs Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline pre

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 5,600 kg, maximum load weight: 33,400 kg, overall weight: 39,000 kg, axle configuration: 3 axles, loading space length: 9,200 mm, loading space width: 2,420 mm, loading space height: 2,150 mm, loading space volume: 50 m³, total length: 10,300 mm, total width: 2,550 mm, total height: 4,040 mm, suspension: air, tire size: 385/65 R 22,5, tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Further Information Chassis, Semi-Trailer, Tipper Bsdpfxei Ri Ihj Amrewu Fine-grained steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front end, patented 24 tons, 2-speed landing gear, single-sided operation, with straight lower part, without stroke compensation 2 support wedges with holder Underrun protection, foldable Half-shell fenders Integrated fender holder, surface designed to repel stones With anti-splash flaps, only on the last axle 1 tarpaulin rod with bracket 2 towing hooks at the rear Axles + Suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser-aligned to reduce tire wear and fuel consumption Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking System 2-line compressed air braking system, color-coded lines for easy servicing Spring brake parking brake 2 tamper-proof coupling heads at the front, without connection line EBS, Electronic Braking System with EBS socket at the front, without connection cable Note: The trailer may only be pulled by tractor units that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle – Driving Stability System Wheels and Tires 385/65 R22.5, manufacturer’s choice Steel rims, factory silver "TPMS" Tire Pressure Monitoring System according to ECE R 141, display via the tractor unit’s display, via EBS, without installation in the truck (this must be available in the truck. Only on base tires). Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides Yellow LED lighting on the sides linked to the turn signal "flashing side lights" 2 white position lights at the front 2 white/red outline lights at the rear 2 x 7-pin tamper-proof sockets at the front, without connection cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chromed, with HDK screw sleeve, fixed part, NW 48 mm (without hose connection) Operated hydraulically via truck auxiliary drive Tipping Body Aluminum box tipper body made of high-quality, abrasion-resistant material, front wall 5 mm thick, with outer wall made of 30 mm hollow chamber profiles, neatly welded, with top edge profile that prevents material from spilling out. Inside with access ladder on the front wall (not in connection with Cramaro). Shovel and broom holder on the outside of the front wall. Greenline – tapered and aerodynamic tipper body design Membrane – rear wall Rear wall with double-joint hinge, mounted to allow movement, with 2-part door division 1/2 to 1/2, at the top with a pivoting gantry, with one grain slide per door. Rear wall with rubber seal. Note! Heat resistant up to max. 170°C! Floor consistently 6 mm thick Standing platform with access ladder, connection plate for air/electrical and brake with large clearance for best possible operation. Roller cover, single-sided for depositing on the right-hand side, with central locking on the left-hand side Approval Country/Signage Germany Type approval according to EC 2007/46 24/7 service hotline Prepared for single-row license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red at the rear Painting Frame DB 7350 Novagra

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,750 kg, maximum load weight: 30,250 kg, overall weight: 35,000 kg, axle configuration: 2 axles, loading space length: 7,200 mm, loading space width: 2,350 mm, loading space height: 1,450 mm, loading space volume: 25 m³, total length: 8,600 mm, total width: 2,550 mm, total height: 3,000 mm, suspension: air, tire size: 385/65 R 22.5, tire condition: 100 %, Custom-made transport solution Configure your Fliegl vehicle according to your requirements. The vehicle shown is an example. Production and equipment are tailored to individual customer requirements. More information Chassis, semi-trailer, tipper Fine-grained steel welded construction, in basic lightweight design, turntable with interchangeable 2 kingpin Curved front end, patented 24 tons, 2-speed landing gear, single-side operation, with straight lower part, without thrust compensation Underrun protection, foldable Half-shell mudguards Towing hook at the rear Axles + suspension SAF disc brake axles with 430 mm disc diameter Axle/suspension laser-aligned to reduce tire wear and fuel consumption Bwedoi Ri Nfepfx Amrju Axles in off-road design Air suspension 1st axle, automatic lift axle, including forced lowering and starting aid Hot-dip galvanized lift axle mechanism, 10-year warranty against rust-through Braking system 2-line compressed air braking system, color-coded lines for easy servicing Spring-loaded parking brake 2 fail-safe coupling heads at the front, without connection line EBS, electronic braking system with EBS socket at the front, without connection cable Note: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! With lifting and lowering valve Vehicle - driving stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver "TPMS" tire pressure monitoring system according to ECE R 141, display via the display in the towing vehicle, via EBS, without truck installation (this must be available in the truck. Only for basic tires). Electrical system 24 volts, multi-chamber lights, yellow LED lighting on the side Yellow LED lighting on the side coupled with the turn signal "Flashing side lights" 2 white position lights at the front 2 white/red marker lights at the rear 2 x 7-pole fail-safe sockets at the front, without connection cable Hydraulics Low-pressure cylinder, max. 170 bar, smallest stage hard-chromed, with HDK screw connection, fixed part, NW 48 mm (without hose connection) Operation hydraulically via truck auxiliary drive Body Steel round body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with externally mounted hydraulic cylinder with ladder on the front wall. Greenline - conical and aerodynamic body shape Shovel and broom holder on the outside of the front wall. Membrane - rear wall Rear wall as a swing gate with double hinge, externally mounted with double hook locking. 2 clamping screws with lever locks on the side below. Side walls continuous, 4 mm thick, floor 4/5 mm thick, wear-resistant and weight-optimized construction Standing platform with ladder, connection plate for air/electricity and brake with large space for best possible operation. Roll cover on one side for stowing on the right, with central locking on the left Country of registration/signs Germany With Dekra approval and certificate (according to §13 EG - FGV) Superstructure strength according to EN 12642 24/7 service hotline Prepared for license plate holder, single row Contour marking with reflective tape according to ECE R 048, white on the side and red at the rear Paint finish Frame DB 7350 Novagrau 10-year warranty against rust-through Support feet, black coated Body RAL, single color Roll cover RAL, single color Available in thermally insulated design!

Condition: used, machine/vehicle number: WFDFLT21301005260, empty load weight: 2,500 kg, maximum load weight: 10,900 kg, overall weight: 13,400 kg, axle configuration: 2 axles, first registration: 11/2015, tire size: 285/70 R19,5", Additional information: Chassis: Fine-grain steel welded construction, telescopic support legs, chock blocks with holder, underrun protection made of steel, half-shell fenders. Towing system, tandem trailer: Drawbar with tested 50 mm towing eye, lower coupling, drawbar mechanically adjustable in length. Axles: BPW disc brake axles, air suspension with raise and lower valve, electronic dolly steering system. Braking system: 2-line pneumatic braking system, spring-loaded parking brake, Duomatik coupling head at the front, with connecting lines to the tractor unit, non-interchangeable coupling heads for the semi-trailer, EBS, electronic braking system with EBS plug at the front, with connecting cable. Electrical system: 24 volts, yellow side lighting, 2 white position lights at the front, 2 white/red marker lights at the rear, 1 x 15-pin plug at the front, with connecting cable to the truck, 1 x 15-pin plug with connecting cable to the semi-trailer. Bwodpfx Asi Ri Rremrsu Approval: Outline marking with reflective strips according to ECE R 048, warning sign according to ECE - 70, truck. Saddle height approx.: 950 mm.

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 5,070 kg, maximum load weight: 33,300 kg, overall weight: 38,000 kg, axle configuration: 3 axles, loading space height: 990 mm, total length: 13,990 mm, total width: 2,550 mm, suspension: air, tire size: 385/55R22,5", tire condition: 100 %, Customized Transport Solution Configure your Fliegl vehicle to meet your specific requirements. The vehicle shown is an example. Production and equipment are customized according to customer specifications. Semi-Trailer Container Chassis Fine-grained steel welded construction, semi-trailer plate with 2 interchangeable kingpins and 2 kingpin positions Container Mounts: Rear extension retracted: 1 x 20-foot or 1 x 30-foot, flush with rear Center telescopic stage 1, rear extension extended to stage 1: 2 x 20-foot or 1 x 40-foot, with or without gooseneck tunnel Center telescopic section, 2nd stage; rear extension extended, 2nd stage: 1 x 45-foot container with gooseneck tunnel and rear overhang Center telescopic section, 2nd stage; front extension extended, 1st stage Rear extension extended, 2nd stage 1 x 45-foot container with long gooseneck tunnel and beveled corners Center telescopic system as a telescoping central tube frame with bolt locking mechanism with rear height adjustment and foldable center supports for containers without tunnels Container guide at the front, plug-in and removable Plug-in adapter for front locking, to secure containers without tunnels from below, with mounting bracket when not in use Front extension mounted on rollers, manually extendable (for 45-foot containers with long tunnels) Rear extension mounted on rollers, with hand crank 24-metric-ton, 2-speed support jack, single-sided operation Extendable underrun protection for 45-foot containers Rear bumper Axles + Suspension Bjdpji Ri R Sefx Amrewu SAF disc brake axles with 430 mm disc diameter Laser-measured axles/chassis to reduce tire wear and fuel consumption Offset wheelbase mm (combined transport) up to 44to gross train weight Air suspension 1st axle: automatic lift axle, including forced lowering and start-up assist; operated by 3 brakes (start-up assist functions up to a 30% axle load exceedance and at speeds up to 25 km/h) Brake System 2-line compressed air brake system; color-coded lines for easy servicing. Spring-loaded parking brake Tele Control Axle relief for easy telescoping 2 non-reversible coupling heads at the front, without connecting line EBS, Electronic Brake System with EBS socket at the front, without connecting cable Caution: The trailer may only be towed by towing vehicles that ensure the effectiveness of the ABS! With lift & lower valve Vehicle stability control system Axle load detection via EBS CAN bus signal, for display in the cab; truck must be equipped accordingly; no truck installation required (no calibrated scale) Wheels and Tires 385/55 R22.5, manufacturer’s choice Steel rims, factory silver Electrical System 24 volts, multi-chamber lights, LED taillights and brake lights, yellow LED side lighting (Note: With certain towing vehicles, false diagnostic errors may occur even though the system is functioning properly) 2 white front position lights 2 white/red lane-departure warning lights at the rear 2 x 7-pin reverse-proof sockets at the front, without connecting cables Operating Instructions When transporting 45-foot containers with a short tunnel, with or without a front extension, the permissible system length from the kingpin to the rear edge of the vehicle and the total train length of 16,500 mm will be exceeded! The underrun protection must be extended manually! A special permit pursuant to § 70 StVZo is required! Type Approval pursuant to EC Directive 2007/46

Condition: new, functionality: fully functional, machine/vehicle number: Produktpalette, empty load weight: 4,860 kg, maximum load weight: 23,140 kg, overall weight: 28,000 kg, axle configuration: 2 axles, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 800 mm, total length: 13,800 mm, total width: 2,550 mm, total height: 2,538 mm, suspension: air, tire size: 235/75 R17,5", tire condition: 100 %, # Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications. --- ## Chassis – 2-Axle Jumbo Platform Semi-Trailer * High-tensile fine-grain steel welded chassis construction * Fifth wheel plate with replaceable 2" king pin * New slightly inclined outer frame with integrated Load-Lock profile for securing lashing straps * 24-tonne two-speed landing gear, single-side operation, straight foot design, without thrust compensation * Free landing leg corner dimension / rear swing clearance approx. 1,920 mm * 2 wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Quarter mudguards in front of and behind each axle * Spare wheel carrier for one spare wheel, including wheel mounting kit * Lockable plastic toolbox with shelf insert, dimensions: 620 × 360 × 440 mm (W × H × D), padlock not included --- ## Axles & Suspension * Drum brake axles (manufacturer's choice) * Laser-aligned axles and running gear for reduced tyre wear and improved fuel efficiency * Air suspension --- ## Braking System * Dual-line compressed air braking system * Colour-coded air lines for simplified maintenance * Spring-loaded parking brake * Front Duomatic coupling without connecting hoses * EBS (Electronic Braking System) with front EBS socket, without connecting cable * Integrated raise-and-lower valve * Vehicle Stability Control System Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. --- ## Wheels & Tyres * 235/75 R17.5 tyres (manufacturer's choice) * Steel rims, factory silver finish --- ## Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights * 2 white front position lights * 2 white/red rear outline marker lights * 1 × 15-pin front socket without connecting cable --- Bwodpfskv Uvzsx Amrju ## Platform * Approx. 30 mm phenolic-coated plywood floor * High point-load capacity, suitable for forklift axle loads up to 5,600 kg --- ## Front Wall * Front wall made of 25 mm aluminium hollow profiles, approx. 1,350 mm high * Heavy-duty steel corner posts in volume specification --- ## Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included (according to §13 EC-FGV) * 24/7 service hotline * Prepared for single-line licence plate holder * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) --- ## Finish * Chassis: hot-dip galvanised or painted according to customer requirements * Aluminium front wall --- # Customized Transport Solution Configure your Fliegl vehicle according to your individual requirements. The vehicle shown is an example configuration. Production and equipment are tailored to customer specifications.

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT33902017848, empty load weight: 6,537 kg, maximum load weight: 28,463 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 10/2015, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,790 mm, total length: 13,850 mm, total width: 2,550 mm, total height: 4,000 mm, suspension: air, tire size: 385/65 R22.5", color: silver, The images are archive images! The vehicle may be in use! Bwedpfxokyrmis Amrju Fine-grained steel welded construction in lightweight design, kingpin plate with 2 replaceable kingpins, outer frame slightly angled with load-lock profile for attaching lashing straps. Note: to attach the straps in conjunction with the side walls, the side walls must be opened. 24-ton, 2-speed landing gear, single-side operation, with straight lower section, without lateral thrust compensation, door latch on the side, support wedges with holder, pallet box for 32 Euro pallets (long version), ground clearance approx. 300 mm. Note: Free support foot distance or free rear swivel radius approx. 1930 mm, quarter-shell fenders in front of and behind the axle unit, with anti-splash flaps only on the last axle, rear impact protection, pallet stop on both sides approx. 20 - 25 mm high, in bolted design, loading height is reduced by approx. 20 - 25 mm. BPW disc brake axles with 430 mm disc diameter, air suspension, 1st axle automatic lift axle, including forced lowering and starting assist, actuation 3x brakes (with starting assist up to max. 25 km/h). Floor: Sieve-printed plates approx. 30 mm thick, crossbeams with omega insert, on longitudinal girders for high point load capacity for forklift axle load up to max. 7100 kg. Front wall/corner posts at the front: 2,480 mm high, corner posts made of steel in a full-volume design, release mechanism for side tarpaulin on the front wall, at the bottom inside at a height of approx. 140 mm with steel impact protection. Roof: Sliding tarpaulin, end lift at the rear that can be folded up, with tarpaulin that can be slid from back to front, L-shaped roof beam for the automotive industry, internal width between the roof beams approx. 2,490 mm, tarpaulin color: white, hydraulic lifting roof with hand pump at each corner post, can be raised by 400 mm. Can be driven with the raised roof, adjustable by 4 x 50 mm upwards. Note the total height! Includes tarpaulin extension of 200 mm, only in conjunction with the tarpaulin.

Condition: new, machine/vehicle number: Produktpalette, empty load weight: 4,600 kg, Additional information Frame Steel welded construction made of fine-grain steel, hot-dip galvanized, flat platform without edge rim, slope of the loading area towards the rear axle by approx. 8° downwards. Longitudinal beams made of steel profiles, steel frame hot-dip galvanized, with NIRO sheet metal at the bend as a rope guide - flush with the floor. For trucks with wheelbase: 2nd axle 1,795 mm / 2nd to 3rd axle 4,105 mm and 3rd to 4th axle 1,350 mm Tow hitch Tow hitch ball head D24.8: (height from floor to top edge approx. 480 mm), towing capacity 2,800 kg, including mounting and electrical system with 7-pole socket Accessories/Modifications 2 holders for wheel chocks, aluminum side underrun protection, foldable - These are taken over from the truck! Steel underrun protection, quarter-shell fenders with mud flaps - These are taken over from the truck! Storage box Plastic toolbox, with drawer and insert, w=650 / h=520 / d=670 mm, can be locked with a padlock 1 holder for 3 pieces of gasoline canisters 1 stainless steel storage box, w=600/h=400/d=500 mm, with polished door, including locking mechanism, contains control valve and electro-hydraulic pump unit. Control box with all-round door seal and sealing sleeves on the back Electrical system Adjustment of the existing tail lights, 2 additional LED work lights, recessed in the front wall switched via parking lights with switch on the front wall outside on the driver's side, 1 LED work light, at the rear, with integrated reversing camera including color flat-screen monitor, screen with suction cup holder and power supply via 24 volts, voltage divider 24/12V, 1 7-pole 12V socket = adapter Floor Mega Grip made of interlocking galvanized grating, steel grating 50/4 including with a mesh size of 50 mm. Top side with anti-slip interlocking, continuously laid over the entire main frame platform Tie-down eyes 12 pairs of tie-down eyes in the outer frame, freely pivotable - each 10 tons. 1 at the very front and the last one at the very rear. 1 tie-down eye at the very rear in the middle for attaching the winch cable 12 tie-down eyes recessed in the center of the floor, each 5 tons. Front wall Front wall made of steel sheet, height 1,500 mm. Fixed with corner pillars at the front wall height. Each 2 x 12 mounting brackets for lashing chains mounted on the left and right on the front wall Winch Electric winch, 24 volts, pulling force approx. 6,350 kg, mounted in the center on the front wall (recessed with loading bridge), operated with a wireless remote control, rope length min. 35 m x 9.5 mm, with rope window, with rope pressure plate, including overload protection, rope free-running clutch, hand switch with approx. 5 m control lever, acceptance of the winch, civil engineer's test report, test book, operating manual Ramps Length 3,500 mm - 2-piece (2,000 mm + 1,500 mm), width 850 mm, load capacity 20,000 kg / pair (also when loading with ramps), electro-hydraulically foldable and laterally adjustable - including electro-hydraulic pump unit. Ramp angle approx. 8° with lowered rear axle Ramp surface made of steel grating, hot-dip galvanized, with anti-slip interlocking. Ramps can be slid together to approx. 170 mm, ramp extension hydraulically. Ramp prepared for operation on a loading ramp with full load capacity. Ramp locking with 2 tension straps. Ramp tip offset for resting on loading ramps. Bwodpfx Aek Unitemrou Labeling of the ramp operation. Lowering brake valve for lowering the ramp Support Adjustable support le

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT22701003408, empty load weight: 4,800 kg, maximum load weight: 22,200 kg, overall weight: 27,000 kg, axle configuration: 2 axles, first registration: 01/2015, next inspection (TÜV): 02/2027, loading space length: 13,650 mm, loading space width: 2,480 mm, total length: 13,850 mm, total width: 2,550 mm, suspension: air, tire size: 385/55 R19,5", color: red, Please note: The images shown are archive photos. The vehicle may still be in operation at the time of inquiry. # 2-Axle Fliegl Mega Platform Semi-Trailer ## Weights & Dimensions * Gross Vehicle Weight (GVW): 27,000 kg * Payload (approx.): 22,200 kg * Axle load: 16,000 kg * Kingpin load: 11,000 kg * Unladen weight (approx.): 4,800 kg (± manufacturing tolerance) * Overall length: approx. 13,850 mm * Overall width: max. 2,550 mm Bwodpfxsy Sk U Ao Amrsu * Overall height: approx. 2,245 mm * Platform length: approx. 13,650 mm * Platform width: approx. 2,480 mm * Fifth wheel height: approx. 950 mm * Kingpin setting: approx. 1,680 mm * Front corner radius: approx. 2,040 mm --- ## Chassis – Mega Platform Semi-Trailer * High-tensile fine-grain steel welded chassis construction * Fifth wheel plate with replaceable 2" king pin * 13 pairs of recessed lashing rings integrated into the outer frame, each rated at 2.5 tonnes * Outer frame with integrated Load-Lock profile for quick attachment of lashing straps * 24-tonne two-speed landing gear, single-side operation, straight foot design, without thrust compensation * Wheel chocks with holders * Aluminium side underrun protection * Steel rear underrun protection * Quarter mudguards --- ## Axles & Suspension * 1st axle: SAF drum brake axle * 2nd axle: BPW drum brake axle * Air suspension --- ## Braking System * Dual-line compressed air braking system * Spring-loaded parking brake * Two non-interchangeable coupling heads at the front (without connecting hoses) * EBS (Electronic Braking System) with front EBS socket, without connecting cable * Integrated raise-and-lower valve * Vehicle Stability Control System Note: The trailer may only be operated with towing vehicles that ensure proper ABS functionality. --- ## Wheels & Tyres * 385/55 R19.5 tyres (manufacturer's choice) * Steel rims, factory silver finish --- ## Electrical System * 24 V electrical system * Multi-chamber rear lights * Yellow LED side marker lights, recessed as far as possible for maximum protection * 2 white front position lights * 2 white/red rear outline marker lights * 2 × 7-pin front sockets, without connecting cables --- ## Platform * Approx. 30 mm phenolic-coated plywood floor * Omega-reinforced cross joints * Longitudinal subframe supports for high point-load capacity * Suitable for forklift axle loads up to 7,100 kg Note: Minor floor distortion due to weather conditions is possible. --- ## Front Wall * Front wall, approx. 1,200 mm high * Heavy-duty steel corner posts in volume specification * Integrated inspection windows --- ## Registration & Compliance * Registration country: Germany * DEKRA inspection and certification included * 24/7 service hotline * Prepared for single-line licence plate holder * Rear warning plate according to ECE R70 * Reflective contour markings according to ECE R048 (white on the sides, red at the rear) --- ## Paint Finish * Chassis: RAL 3002 Carmine Red * Landing gear: black coated * Front wall: RAL 3002 Carmine Red --- Please note: The images shown are archive photos. The vehicle may still be in operation at the time of inquiry.

Condition: used, functionality: fully functional, machine/vehicle number: WFDFLT21001013325, empty load weight: 2,500 kg, maximum load weight: 8,000 kg, overall weight: 10,500 kg, axle configuration: 2 axles, first registration: 11/2023, loading space length: 5,500 mm, loading space width: 2,050 mm, loading space height: 630 mm, total length: 7,280 mm, total width: 2,550 mm, total height: 2,900 mm, suspension: steel, tire size: 235/75 R17,5", color: blue, The images shown are archive images. The vehicle may still be in use. Chassis: Central axle trailer, low-bed Fine-grained steel welded construction Gearbox support leg at the front Telescopic rear support Chocks with holder Mudguards made of steel sheet over both wheels Side impact protection, aluminum Coupling device for central axle trailer Drawbar with tested 40 mm drawbar eye Drawbar height-adjustable via spindle, max. adjustment range 250 mm Axles + Suspension Euro axles of our choice, with tapered roller bearing and S-cam brake "Axle/chassis laser-aligned" - reduces tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearing and mechanical axle load compensation (rocker arm compensation) Wheels and Tires 235 / 75 R 17.5" according to manufacturer's choice Steel rims, factory silver Braking System 2-line compressed air braking system Spring brake parking brake 2 non-interchangeable coupling heads at the front, with connecting lines to the tractor unit ABS and ALB, with ABS connector at the front, with connecting cable Note: The trailer may only be towed by tractor units that ensure the effectiveness of the ABS! Electrical System 24 Volt, multi-chamber lights, yellow LED lighting on the sides 2 white position lights at the front 2 white/red side marker lights at the rear 1 x 15-pin connector at the front, with connecting cable Bridge TTS Low-lying steel pan, bridge floor made of steel/non-slip steel plate, steel walls solidly welded to the floor Bridge length 5500 mm Pan at the front and side with "Load-Lock profile" for attaching lashing straps (8 pieces at the front, 16 pieces on each side) Note: Slight undulation of the floor may occur due to welding distortion! Pair of lashing eyes, 1 x at the front in the corners of the steel pan and 1 x at the rear in the floor, each 5 tons Additional pair of lashing eyes in the floor, each 5 tons Ramps Steel ramps, 2,300 mm long, 510 mm wide, laterally adjustable with handrail on the ramps covered with wood (tip area with steel/non-slip steel plate) with gas spring for single-person operation Operating instructions The specified total weight is technically possible, depending on the cargo, the total weight may not be reached while complying with the permissible axle/support and saddle loads. (Poor handling and tracking behavior possible due to incorrect load distribution) Country of Registration/Signage Country of Registration: Germany with DEKRA inspection and certificate (according to §13 EG - FGV) Bwsdpfx Amozadb Derju 24/7 service hotline prepared for single-line license plate holder Contour marking with reflective tape according to ECE R 048, white on the sides and red at the rear Painting Frame: RAL 5002 Ultramarine Blue Ramps: Hot-dip galvanized The images shown are archive images. The vehicle may still be in use.

Condition: new, functionality: fully functional, power: 440 kW (598.23 HP), fuel type: hybrid, color: other, Year of construction: 2026, Equipment: ABS, cabin, onboard computer, CONSTMACH V-90 mobile vertical shaft impact crusher is a compact mobile crushing and screening plant that offers high efficiency and superior quality. Also known as a mobile sand making machine, this system is an ideal solution for producing material in the 0–5 mm range, in a cubic form and with a fine grain size. Thanks to its engineering marvel design, robust construction, and long-lasting components, the V-90 delivers maximum performance even in challenging field conditions. This model can process materials obtained after primary and secondary crushing operations, as well as natural stones up to 45 mm in size directly. It delivers superior crushing performance on stones of varying hardness, such as limestone, basalt, granite, dolomite, and gabbro. Production capacity ranges from 200 to 250 tons per hour, depending on material hardness. In addition to sand, simultaneous production of three different final fractions is possible. The V-90 consists of advanced components such as a vibrating feed bunker, VSI 900 CR vertical shaft impact crusher, vibrating screen, feedback and stock belts, hydraulic-legged mobile chassis, and PLC-controlled automation system. Thanks to its user-friendly design, installation time is very short, and it can be commissioned without requiring external equipment. Siemens–Schneider brand electronic components and remote control capability allow the system to be managed from a single tablet. V-90 Mobile Vertical Shaft Impact Crusher Technical Specifications Production Capacity: 200–250 tph Maximum Feed Size: 45 mm Feed Height: 4.5 meters Main Configuration: VSI Crusher + Vibrating Screen Total Motor Power: 440 kW Electric Generator Requirement: 850 kVA Plant Weight: 45 tons Plant Dimensions: 20.8 (L) x 3.85 (W) x 4.5 (H) meters Chassis Type: Hydraulic-mounted, wheeled single chassis Why Choose the V-90 Mobile Vertical Shaft Impact Crusher? At CONSTMACH, we combine high-quality engineering with solutions that make a difference in the field. Our V-90 model offers maximum efficiency in rock crushing and sand production while providing a high return on your investment with low operating costs. Its design suitable for international transport, easy installation, and durable construction allow you to quickly bring your projects to life. With its long-lasting components, our technical support, and spare parts guarantee, the V-90 will be the key to uninterrupted performance in your production line. What Do We Do at Constmach? Constmach is a leading machine manufacturer serving the construction and mining industries with a wide range of products tailored to their needs. Our product portfolio includes concrete block making machines, stationary and mobile concrete plants, stone crushing machines, stone crushing and screening plants, sand washing machines, sand making machines, asphalt plants, conveyor belt systems, jaw crushers, and mobile crushing plants. With its high quality standards, innovative production approach, and customer-focused solutions, Constmach stands out as a reliable brand in both national and international markets. Our products continue to be the preferred choice of industry professionals due to their durability, efficiency, and long-lasting performance. Bedoxqgcwspfx Amrewu