Used Force for sale (8,559)

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Ledpsxyl U Rsfx Affjak

Condition: ready for operation (used), Year of construction: 2017, Additional Equipment Hydraulic unit with pump, oil tank, and valves for operating the pressure and auxiliary cylinders Hydraulic control unit located at the upper part of the press for maintenance ease Control panel with buttons, selector switches, and a pressure control gauge This CMB PFR-CCL was manufactured in 2017. It features a motorized loading table and an automatic cold press with a maximum pressing force of 160 tons. The press operates with a hydraulic unit and a control panel for precise operation. Ideal for handling large panel sizes up to 5,500 x 1,600 mm. If you are looking to get high quality pressing capabilities consider the CMB PFR-CCL machine we have for sale. Contact us for more information. Ledox Nkm Hepfx Affeak Application Types Pressing / Laminating

Condition: excellent (used), Year of construction: 2003, operating hours: 21,200 h, functionality: fully functional, machine/vehicle number: 190332, Equipment: documentation/manual, Injection molding machine 3 colors (horizontal /vertical/ and 3. in L-position with protective housing) The machine can be used as a 2 colour/2K machine and the 3rd can be deactivate immediately available from our warehouse in Hannover Make: Arburg Type: 420C 1000-150/150/60 year of construction 2003 Control: Selogica Hours: 20092 h without turntable +++++clamping unit +++++ Clamping force: 1000 kN / 1000 to. tie bar distance: 420 x 420 mm platen size: 795 x795 mm tool height 300 mm distance platens max. 950 mm ejector 225 mm /66 kN ++++Injection unit 1 (150 unit) ++++ Screw size: 15 mm (high shut-off fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2750 bar ++++Injection unit 2 (150cc unit) ++++ Screw size: 15 mm (highly screwed fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2750 bar ++++Injection unit 3 (60cc unit) ++++ Screw size: 15 mm (highly screwed fixed) Injection volume: 17 ccm Injection weight: 15 gr. Injection pressure: 2080 bar Extras 2x core pull 1 ALLROUNDER 420 C 1000 - 150 / 150 / 60 fully hydraulic screw injection molding machine mold clamping force 1000 kN voltage 400 V / 50 Hz 1 Vertical injection unit instead of clamping tie bars mounted on carriers for 2nd injection unit, manually operated, working position adjustable between 70 and 250 mm VE-404/02 1 Open nozzle 15 mm low-wear, without heating tape (1.SPE 150) VE-902/00 1 Technology level 2 - servo-controlled Hydraulic system -two control pumps for controlled machine movements, path-dependent, controlled target ramps. The build-up of the tool clamping force programmable + controlled. Clamping force is servo-controlled via second pump. The nozzle contact force programmable. The contact force can be set manually, the value is maintained in a controlled manner. This technology level is a prerequisite for simultaneous movements of the nozzle, ejector and optional core pullers. Including equipment package for "extended travel movements". VE-132/03 1 Technology level 3 Hydraulic system with 3 control pumps for simultaneous movements of the main axes and for faster movements of the secondary axes. For the 2-K machines as hydraulic system for the 2nd injection unit (prerequisite is technology level 2, VE 132/03) VE-130/40 1 heating tape for open nozzle VE-320/00 1 Injection unit 150 for vertical injection into mold partition for 2-component processing VE-136/02 1 position controlled screw with control valve at the injection unit, incl. controlled back pressure, nozzle contact force manually adjustable VE-561/20 1 position-controlled screw with control valve for multi-component machines, incl. controlled back pressure, nozzle contact force manually adjustable - for injection unit 2 VE-561/30 1 injection unit 60 for horizontal injection into mold partition as 3rd injection unit for multi-component processing (L-position) VE-906/00 1 for VE 906/00 injection unit 60 in L-position: unit lowered by 70 mm, incl. special parting line full protection VE-907/00 1 Plasticizing barrel set 15 mm (without nozzle), with advanced feed and pressure reducing valve, in highly wear resistant design 1 Open nozzle 15 mm wear-resistant, without heating band (L-position) VE-909/00 Laodpfx Afogrzh Ejfsk 1 Nozzle tip with radius 15 (L-position) VE-910/00 1 Heating tape for open nozzle (L-position) VE-911/00 1 Position-controlled screw for the third injection

Condition: good (used), Year of construction: 2019, operating hours: 8,173 h, functionality: fully functional, turning length: 12,025 mm, turning diameter: 480 mm, spindle speed (max.): 3,250 rpm, travel distance X-axis: 308 mm, travel distance Y-axis: 120 mm, travel distance Z-axis: 1,240 mm, bar passage: 102 mm, overall weight: 7,200 kg, controller model: DMG MORI SLIMline Multi-Touch Control, control type: CNC control, CLX 550 V6 2-axis universal lathe with driven tools incl. C-axis, Y-axis, and counter spindle Standard equipment: 1. Ergonomic DMG MORI SLIMline operating panel 2. Main spindle A2-8 with AC motor, drive power 22 / 33 kW (100/40% DC), 3,250 rpm 3. Counter spindle A2-6 with ISM 52 synchro, drive power 13 / 14 kW, torque 171.5/192 Nm (100/40% DC), 5,000 rpm 4. 12-position servo turret, VDI 40 mounting with Trifix® precision interface and 12 driven tool stations per DIN 5480 5. Y-axis ± 60 mm 6. Chip tray 7. Hollow clamping device, max. bar capacity D 80 mm 8. Electronic handwheel Drive power (100%/40% DC) 22/33 kW Hydraulic clamping device with bar capacity diameter 102 mm, surcharge Differential pressure clamping for main spindle Bar package & interface option includes: - Workpiece unloader for parts up to D 80 x 200 mm long (D 100 x 200 mm with option C-B7000G) Max. workpiece weight 4 kg - Interface for bar loader or bar feed unit (DMG MORI standard interface) - Hinged belt chip conveyor instead of chip tray - 4-color signal tower Recommended additional option: Double cartridge filter for coolant, especially for production environments with very high chip volumes. Automatic workpiece ejector for counter spindle with internal coolant supply for clamping device flushing. Note: Option recommended for machines with workpiece unloader option. External flushing for counter spindle, option recommended for machines with automation Differential pressure clamping for counter spindle Tailstock function for counter spindle, mechatronic force control programmable in the software (force 250-600 daN), including foot switch (only for CLX 550 V6) Direct measuring system for X- and Y-axis (option only available for V4 and V6 versions) Ljdpfx Afexx Tcmefeak Manual tool measuring device in the working area, brand Marposs Documentation according to 'Technical Documentation Delivery List' – included in the machine price. Software option: DXF import for converting DXF files into NC programs (SIEMENS control) Tool monitoring system: Easy Tool Monitor 1.0, monitors each cutting operation against a set limit. Simple learning function for determining the monitoring limit per tool and cutting operation; manual adjustment/correction possible. Technology cycle: Alternating speed (turning) for vibration-sensitive applications Note: We offer flexible financing solutions for all machines as well as a professional relocation service. Dismantling, transport, and professional installation – everything from a single source. Billing based on individual terms and duration. Contact us for your personal offer.

Condition: ready for operation (used), Year of construction: 1998, pressure 120 t Laodpfxox Ni Ebj Affok chamfer lenght 3050 mm distance between columns 2550 mm stroke of upper beam 155 mm throat 350 mm ajustment speed 100 mm/sec working feed 9.0 mm/sec return speed 77.0 mm/sec Control "P 40" work height max. 878 mm table width 104 mm oil volume 150 l total power requirement 11.0 kW weight 7550 kg range L-W-H 3550 x 2150 x 2600 mm Equipment: - NC electro-hydraulic press brakes - with NEW ELGO NC control unit "P40" * New price approx. 4.000 Euro * Control / movement of the backgauge - X axis (target/actual input) * Control / movement of the depth setting - Y axes (target/actual input) * Inching mode for X axis Y axes also possible - Swivel operation, front left - NC controlled axes : Y1 Y2 X - NC electro-motorized backgauge (X axis) * with 2x manually adjustable stop fingers * including lateral and height adjustment (Z R axis) - 1x branded set of upper tools (split) - 1x branded Multi-V bottom die block - Lateral safety guard (hinged doors) - Rear safety guard (hinged door) - 1x free-moving 2-hand/foot control - Operating instructions (PDF)

Condition: new, empty load weight: 4,580 kg, maximum load weight: 14,420 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, loading space height: 1,800 mm, loading space volume: 24 m³, suspension: other, tire size: 435/50 R 19,5, color: other, gearing type: other, front tire size: 435/50 R 19,5, rear tire size: 435/50 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-way tipper, loading area approx. 5700 mm x 2420 mm, side walls 600 mm + 2 x 600 mm add-on side walls, complete side wall height approx. 1800 mm, side walls hot-dip galvanized, loading height approx. 1080 mm, 12 x lashing eyes in the floor, reinforced geared support winch with load and fast gear at the front, 2 x folding supports at the rear, 435/50 R 19.5, , chassis and tipper body hot-dip galvanized, , surcharge for:, aluminum ramps, price: 1600 euros, , --  Subject to printing errors, errors and changes, sample images --, more data at: !, more details: ! Lasdpfxjx Nidwo Affek

Condition: good (used), Year of construction: 1969, Hydraulic press, single-column press, C-column press, oil-hydraulic press, hydraulic single-column press, press machine, hydraulic punch for Schüco tools, hydraulic press, multifunctional punch, punch, universal punch, punching machine -Handover: in the current condition as viewed -Condition: Cylinder slightly leaky Lasdpfx Aew A Rzdoffek -Hydraulic press: Hydraulic single-column press -Pressing force: 160 tons -Stroke: 600 mm -Insertion height: 800 mm -Table size: 660 x 800 mm -Table hole: Ø 250 mm -Projection: 330 mm -Operation: hand lever -Dimensions: 1780/1090/H2920 mm -Weight: 8000 kg

Condition: new, Year of construction: 2025, operating hours: 8 h, Very robust machine with high pressing force - is also suitable for producing a salable briquette quality * depending on the material. The large press cylinder and the 80 mm briquette make this possible. Our best-selling briquetting press series + Tried and tested, simple technology, for extremely low susceptibility to errors + 25 years of experience, further development and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Surcharge for cooling unit + € 4.995 net, (can also be retrofitted later) * cools the pressing tongs (important from 3.5 hours) and the hydraulic oil * Cooling device recommended for regular use of more than 3.5 hours at a time. Briquette diameter: 80 mm Front bush: 125 mm Briquette stroke max .: 100 mm Briquette lift opt ​​.: 80 mm Output (depending on material): up to 200 kg / h * * depending on the bulk weight * based on a bulk weight of 200 kg per cubic meter Motor power: 9.2 kW 400 volts / 50 Hz / 3 phases Length: 2095 mm Width: 1300 mm Height: 1700 mm Weight: 1250 kg Oil volume: 220 liters Silo diameter: 1200 mm Silo content: approx. 1 qbm Pump: 75 liters Hydraulic pre-compressor Cooling pressing tongs option: yes, with special accessory coolable pressing tongs Hydraulic oil cooling option: yes Cooling of the pressing tongs and the hydraulic oil with cooling device (special accessory) Level monitoring option: yes Laodpfexfwdex Affjk Strand briquette option; yes (depending on material) Option of enlarged filling slide: yes, with special accessory enlarged filling slide CE compliant . Requirements for the raw material: - The moisture content (atro) must be between a minimum of 6 and a maximum of 18% - Chip length maximum 20 mm - Installation temperature: temperature-controlled room at at least + 5 ° C - The loading must be free of metals and mineral impurities such as sand, stones, etc. This can result in damage to the pressing tools and / or increased wear

Condition: excellent (used), Year of construction: 2012, Arburg 820S 4000-2100/400 / Production line with the robot Sepro Industrial Robot SR S5-35 S3 Trans / Operating hours: 42,014 h in automatic mode Year of manufacture: 09.2012 Injection unit: Screw diameter: 60 mm Injection weight: 723 g Injection pressure: 2500 bar Dosing volume: 792 cc Clamping unit: Laodpjx Nhqiefx Affjk Clamping force: 400 t Bar spacing: 820x820 mm Size of the clamping plates: 1171x1171 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - touchscreen Additional equipment: 2K injection molding machine with rotary table and robot Very good technical condition Operating hours: 42,014 h in Automatic operation Euromap 67 Robot interface Air valve x 6 Hydraulic, needle core pull, controlled by a proportional valve x 4 pairs Control with hot runners x 24 Reinforced injection units - bimetal Proportional valve on the vertical injection unit - precise injection Machine with six cylinders / batteries with compressed nitrogen (additional charge for fast work) Parallel movements Automatic tool height adjustment Screw diameter in the vertical injection unit: ⌀40 mm - 184 g/PS The built-in system for controlling the print quality from the Sensor Kistler brand - measuring the tool pressure Original Weber rotary table: very precise, electrically driven by a servo motor controlled by an inverter Rotary table diameter: 1200 mm Purchase of the rotary table at an additional cost Robot Sepro Industrial Robot SR S5-35 S3 Trans Year of manufacture: 2012 3-axis robot: 3 axes are driven by servo motors (electric): X, Y, Z (telescopic) Travel paths in axes approx.: X-5000, Y-1400, Z-2000 Automatic axis lubrication Touch control panel The robot safety package Robot with adapter and protective housing Purchase of the robot for an additional charge Dimensions: Weight: 21000 kg Length/width/height: 8.00x2.32x4.21 m All machines offered are started by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to take part in live technical tests in our company in Łódź. Price: On request

Condition: new, empty load weight: 4,650 kg, maximum load weight: 14,350 kg, overall weight: 19,000 kg, axle configuration: 2 axles, suspension: other, tire size: 435/50 R 19,5, color: other, gearing type: other, front tire size: 435/50 R 19,5, rear tire size: 435/50 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, , with hydraulic tailgate, three-way tipper, side walls 600 mm high, galvanized, loading height approx. 1,080 mm, 4 x lashing eyes, each 5 t, set into the floor, 8 x lashing eyes, each 3 t, set into the floor, reinforced geared support winch with load and fast gear at the front, 435/50 R 19.5, , chassis hot-dip galvanized and tipper bridge hot-dip galvanized or painted, , surcharge for:, aluminum ramps (approx. 3,500 long) and 2 folding supports at the rear, price: 1,700 euros, , , , --  Subject to printing errors, errors and changes, sample images --, more details at: !, more details: ! Lajdpfx Aex Nifboffsk

Condition: new, Year of construction: 2025, Good, used demonstration machine Availability upon request Very robust machine with high pressing force - also suitable for producing briquettes of saleable quality *depending on the material. The large pressing cylinder and the 70 mm briquette make this possible. Our best-selling briquetting press series + Proven, simple technology for extremely low susceptibility to errors + 25 years of experience, continuous development, and know-how + Several thousand machines in use with satisfied customers + Top price-performance ratio Supplement for demonstration cooling unit + €4,980 net, (can also be retrofitted later) * Cools the pressing tongs (important for use after 4 hours) and the hydraulic oil * Cooling unit recommended for regular use of more than 4 hours at a time. Tariff number: 84793010, Briquette diameter: 70 mm, Front bushing: 125 mm, Max. briquette stroke: 100 mm, Optional briquette stroke: 80 mm, Capacity (depending on material): up to 150 kg/h* *depending on bulk density, *based on a bulk density of 200 kg per cubic meter. . Motor power: 9.2 kW, 400 volts / 50 Hz / 3-phase, Lsdpfx Afjd Nm Siofjak Length: 2095 mm, Width: 1300 mm, * with large chamber 1600 mm Height: 1700 mm, Weight: 1250 kg, Oil capacity: 220 liters, Silo diameter: 1200 mm Silo capacity: approx. 1 cubic meter Pump: 75 liters Hydraulic pre-compressor Cooling option for pressing tongs: yes, with optional coolable pressing tongs Cooling option for hydraulic oil: yes Cooling of the pressing tongs and hydraulic oil with a cooling unit (optional accessory) Level monitoring option: yes Extruded briquette option; Yes (depending on material) Optional enlarged feed slide: Yes, with special accessory enlarged feed slide CE compliant Raw material requirements: - The moisture content (dry) must be between a minimum of 6% and a maximum of 18% - Maximum chip length: 20 mm - Installation temperature: Temperature-controlled room at a minimum of +5°C - The feed must be free of metals and mineral contaminants such as sand, stones, etc. This may result in damage to the press tools and/or increased wear.

Condition: excellent (used), Year of construction: 2011, Arburg 1500T 3200-1300 e² / hybrid machine with one rotary table Year of manufacture: 2011 Injection unit: Screw diameter: 60 mm injection weight: 607 g Injection pressure: 2000 bar Metering volume: 664 ccm Clamping unit: clamping force: 320 t tie bar distance: 0x0 mm size of clamping platens: 1510 mm ejector: hydraulic clamping unit: hydraulic Control system: SELOGICA - touch screen Additional equipment: Hybrid machine: high-speed, energy-saving and very quiet Operating hours: approx. 30.000 in automatic mode Euromap 67 Lajdpfx Aex Nhp Soffsk Robot interface Control with air valve Hydraulic core pull x 3 Control with hot runners x 13 Injection unit hardened - bimetal Main machine motor - servo motor driven by inverter Very precise rotary table driven by servo motor controlled by inverter Rotary table diameter: 1500 mm Horizontal injection unit with automatic injection height adjustment Self-closing nozzle Primus sensor - mold pressure control It is possible to convert the injection unit so that it works vertically Dimensions: Weight: 16080 kg Length/width/height: 4.91x2.12x4.62 m All offered machines are started by our service technicians before sale. It is possible to get a video of technical tests of the selected machine or participate in live technical tests in our company in Łódź. Price: Upon request

Condition: new, empty load weight: 4,580 kg, maximum load weight: 14,420 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, loading space height: 1,100 mm, loading space volume: 15 m³, suspension: other, tire size: 435/50 R 19,5, color: other, gearing type: other, front tire size: 435/50 R 19,5, rear tire size: 435/50 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-way tipper, loading area approx. 5,700 mm x 2,420 mm, 600 mm drop sides + 500 mm extension drop sides, hot-dip galvanized drop sides, loading height approx. 1.080 mm, 12 x lashing eyes in the floor, reinforced gear support winch with load and fast gear at the front, 2 times folding supports at the rear, 435/50 R 19.5, , Chassis and tipper body hot-dip galvanized, , Surcharge for:, Aluminium ramps , Price: 1,600 Euro, , -- Misprints, errors and omissions excepted, Sample pictures --, More data under: !, More Details: ! Lasdpfex Nidqjx Affok

Condition: excellent (used), Year of construction: 2008, Arburg 630S 2500-1300 ECO / Production Line with Sepro Industrial Robot SDR 22S Year of manufacture: 2008 Injection Unit: Screw diameter: 55 mm Shot weight: 521 g Injection pressure: 2380 bar Dosage volume: 570 ccm Clamping Unit: Clamping force: 250 t Tie bar distance: 630x630 mm Platen size: 900x900 mm Ejector: hydraulic Clamping unit: hydraulic Control: SELOGICA - touchscreen Additional equipment: Euromap 67 Robot interface Air valves x 4 Laedpfx Afjx Nhp Esfek Hydraulic core pulls x 2 Controller with 15 hot runner zones Injection assembly hardened - bimetallic Machine with cylinder / battery with compressed nitrogen (additional charge for fast operation) ECO – machine equipped with a system to adjust the minimal mould height Robot - Sepro Industrial Robot SDR 22S Year of manufacture: 2016 4-axis robot: 3 axes driven by servomotors (electric); C-axis - pneumatic Axis strokes: X-1500, Y-2200, Z-800 Vacuum x 2 Gripper x 2 Touch control panel Robot with adapter, conveyor belt and protective housing Acquisition of the robot and the conveyor belt available at extra cost Dimensions: Weight: 12,510 kg Length/Width/Height: 6.57x1.76x2.46 m All offered machines are commissioned by our service technicians before sale. It is possible to receive a video of the technical tests for the selected machine or to participate in live technical tests at our company in Łódź. Price: On request

Condition: new, empty load weight: 3,960 kg, maximum load weight: 10,440 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, suspension: steel, tire size: 385/55 R 19,5, color: other, gearing type: other, front tire size: 385/55 R 19,5, rear tire size: 385/55 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-sided tipper, loading area length approx. 5,700 mm, side walls 600 mm high, galvanized, + lattice attachment 1,000 mm high, loading height approx. 990 mm, 4 x lashing eyes in the floor 5 t each, 8 x lashing eyes in the floor 3 t each, reinforced geared support winch with load and fast gear at the front, ?Wide tyres: 385/55 R 19.5, Chassis: Hot-dip galvanized, , Surcharge for:, Aluminium ramps (approx. 3,520 x 400 mm) load capacity 10 t per pair and 2 folding supports at the rear, Price: 1,500 Euro , , , -- Misprints, errors and omissions excepted, Sample pictures --, More data under: !, More Details: ! Laodpfx Afex Niddjfok

Condition: excellent (used), Year of construction: 2016, Arburg 570S 2200-290/100/100 / Production line with the Wittmann W823 robot / Operating hours: 20,499 h in automatic mode Year of construction: 2016 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Injection pressure: 2000 bar Metering volume: 144 ccm Clamping unit: Clamping force: 220 t Distance between tie bars: 570x570 mm Size of the clamping platens: 795x795 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA touchscreen Additional equipment: 3-component injection molding machine, high speed Very good technical condition Operating hours: 20,499 h in automatic mode Euromap 67 Robot interface Air valve x 6 Hydraulic, needle core pull, controlled by a proportional valve x 4 Control unit with hot runners Hardened injection unit - bimetal Proportional valve on the injection unit - precise injection Machine with two cylinders / battery with compressed nitrogen (additional charge for fast work) The machine is designed for operation with an electric turntable. The machine has an inverter to control the servomotor in the rotary table and an interface for connecting the rotary table Parallel movements Screw diameter in the vertical injection unit: ⌀25 mm - 45 g/hp Screw diameter in the lateral injection unit: ⌀25 mm - 45 g/hp Wittmann W823 robot Lodpfx Afox Nhprofjak Year of construction: 2015 5-axis robot: 3 axes are driven by servomotors (electric); axis C and movement A Travel in axes: X-550, Y-1400 (telescopic), Z-3500 Touch control panel The safety package for robots Robot with adapter, conveyor belt and protective housing Purchase of the robot and conveyor belt for an additional charge Dimensions Weight: 10830 kg Length/width/height: 5.53x1.77x3.29 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: new, empty load weight: 3,740 kg, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, suspension: steel, tire size: 385/55 R 19,5, color: other, gearing type: other, front tire size: 385/55 R 19,5, rear tire size: 385/55 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-sided tipper, loading area length approx. 5,700 mm, side walls 600 mm high, galvanized, loading height approx. 990 mm, 4 x lashing eyes in the floor 5 t each, 8 x lashing eyes in the floor 3 t each, reinforced geared support winch with load and fast gear at the front, ?Wide tyres: 385/55 R 19.5, Chassis: Hot-dip galvanized, , Surcharge for:, Aluminium ramps (approx. 3,520 x 400 mm) load capacity 10 t per pair and 2 folding supports at the rear, Price: 1,500 Euro , , , -- Misprints, errors and omissions excepted, Sample pictures --, More data under: !, More Details: ! Laedpfx Afjx Nic Tofek

Condition: excellent (used), Year of construction: 2011, Arburg 570H 2000-800 e² / Hybrid Machine / Production Line with Arburg Multilift Select Robot Year of Manufacture: 2011 Injection Unit: Screw diameter: 50 mm Shot weight: 359 g Injection pressure: 2000 bar Dosing volume: 392 cc Clamping Unit: Clamping force: 200 t Tie bar spacing: 570x570 mm Platen size: 795x795 mm Ejector: electric Clamping unit: toggle lever Control System: SELOGICA - Touchscreen Additional Equipment: Hybrid machine: high-speed, energy-saving, and very quiet Euromap 67 Robot interface Air valves x 4 Hydraulic core pull x 2 Controller with 12 hot runner zones Injection unit hardened - bimetallic Main motor of the machine: servo motor driven by inverter – energy saving Injection unit driven by a servo motor, controlled by an inverter Machine with cylinder / battery with compressed nitrogen (additional charge for fast operation) Central lubrication system Parallel motions Arburg Multilift Select robot, 6 kg transverse Year of manufacture: 03.2011 4-axis robot: 3 axes driven electrically by servo motors; C-axis pneumatic Travel distance in axes: X-400, Y-800, Z-1400 Robot with adapter, conveyor belt, and safety enclosure The purchase of the robot and conveyor belt is available for an additional charge Dimensions: Weight: 8700 kg Lajdpfx Aex Nhploffok Length/Width/Height: 5.58x1.71x2.21 m All machines offered are started up and tested by our service technicians before sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our facility in Łódź. Price: On request

Condition: new, empty load weight: 3,740 kg, maximum load weight: 10,660 kg, overall weight: 14,400 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, suspension: steel, tire size: 385/55 R 19,5, color: other, gearing type: other, front tire size: 385/55 R 19,5, rear tire size: 385/55 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-sided tipper, loading area length approx. 5,700 mm, side walls 600 mm high, galvanized, loading height approx. 990 mm, 4 x lashing eyes in the floor 5 t each, 8 x lashing eyes in the floor 3 t each, reinforced geared support winch with load and fast gear at the front, ?Wide tyres: 385/55 R 19.5, Chassis: Hot-dip galvanized, , Surcharge for:, Aluminium ramps (approx. 3,520 x 400 mm) load capacity 10 t per pair and 2 folding supports at the rear, Price: 1,500 Euro , , , -- Misprints, errors and omissions excepted, Sample pictures --, More data under: !, More Details: ! Lsdpfxjx Nidke Affoak

Condition: excellent (used), Year of construction: 2003, Arburg 570C 2000-350/150 / Production Line with Side-mounted Arburg Multilift Robot / 2K Machine Year of Manufacture: 2003 Injection Unit: Screw diameter: 40 mm Shot weight: 153 g Injection pressure: 2,120 bar Dosage volume: 182 ccm Clamping Unit: Clamping force: 200 t Tie bar spacing: 570x570 mm Platen size: 795x795 mm Ejector: hydraulic Lajdpfxjx Nhn Ue Affok Clamping unit: hydraulic Control system: SELOGICA Additional equipment: Production line with side-mounted Arburg Multilift robot 2K (two-component) machine Air valve x 1 Hydraulic core pull x 5 Control system with hot runner integration Reinforced injection units – bimetallic Proportional valves on injection units – precision injection Vertical injection unit – screw diameter: ⌀25 mm – 49 g/PS All machines offered are started up by our service technicians prior to sale. It is possible to obtain a video of the technical tests of the selected machine or to participate in live technical tests at our facility in Łódź. Price: On request

Condition: new, empty load weight: 4,580 kg, maximum load weight: 14,420 kg, overall weight: 19,000 kg, axle configuration: 2 axles, loading space length: 5,700 mm, loading space width: 2,420 mm, loading space height: 1,600 mm, loading space volume: 22 m³, suspension: other, tire size: 435/50 R 19,5, color: other, gearing type: other, front tire size: 435/50 R 19,5, rear tire size: 435/50 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-way tipper, loading area approx. 5,700 mm x 2,420 mm, side walls 600 mm, 1,000 mm lattice extension, hot-dip galvanized body, loading height approx. 1.080 mm, 12 x lashing eyes in the floor, reinforced gear support winch with load and fast gear at the front, 2 times folding supports at the rear, 435/50 R 19.5, , Chassis and tipper body hot-dip galvanized, , Surcharge for:, Aluminium ramps , Price: 1,600 Euro, , -- Misprints, errors and omissions excepted, Sample pictures --, More data under: !, More Details: ! Lajdpex Nid Defx Affsk

Condition: excellent (used), Year of construction: 2012, Arburg 520S 1600-400/170 e² / Production Line with Geiger Robot Year of manufacture: 10.2012 Injection Unit: Screw diameter: 35 mm Shot weight: 141 g Injection pressure: 2500 bar Dosage volume: 154 cc Clamping Unit: Clamping force: 160 t Tie bar spacing: 520x520 mm Platen size: 695x695 mm Ejector: hydraulic Clamping unit: hydraulic Lasdpfxex Nhnus Affok Control system: SELOGICA – Touchscreen Additional equipment: 2K injection molding machine with rotary table and Geiger robot Very good technical condition Hybrid machine: energy-efficient and very quiet Euromap 67 Robot interface Air valve x 4 Hydraulic core pull x 5 Hot runner control x 12 Reinforced injection units – bimetallic Machine with two cylinders / compressed nitrogen accumulators (additional charge for fast operation) Parallel movements Screw diameter in vertical injection unit: ⌀30 mm - 77 g/PS Integrated Arburg conveyor belt and sorting flap Original Weber rotary table, highly precise – electrically driven Purchase of the rotary table and robot for a surcharge Dimensions: Weight: 8140 kg Length/Width/Height: 4.81x1.84x3.45 m All machines offered are started up by our service technicians prior to sale. It is possible to receive a video of the technical tests of the selected machine or to participate in live technical tests at our facility in Łódź. Price: On request

Condition: new, empty load weight: 4,460 kg, maximum load weight: 14,540 kg, overall weight: 19,000 kg, axle configuration: 2 axles, suspension: other, tire size: 435/50 R 19,5, color: other, gearing type: other, front tire size: 435/50 R 19,5, rear tire size: 435/50 R 19,5, driver cabin: other, emission class: none, fuel: biodiesel, Equipment: ABS, compressed air brake, Three-sided tipper, side walls 600 mm high, galvanized, loading height approx. 1,080 mm, 4 x lashing eyes each 5 t embedded in the floor, 8 x lashing eyes each 3 t embedded in the floor, reinforced gear support winch with load and fast gear at the front, 435/50 R 19.5, , chassis and tipper body hot-dip galvanized, , surcharge for:, aluminium ramps (approx. 3.500 long) and 2 rear folding supports, Price: 1.700 Euro , , , , -- Misprints, errors and omissions excepted, sample pictures --, More data under: !, More Details: ! Laedpfx Ajx Nid Roffek

Condition: excellent (used), Year of construction: 2011, Arburg 520S 1600-290/100 / Production line with Wittmann W823 robot / Operating hours: 20,181 h in automatic mode Year of construction: 09.2011 Injection unit: Screw diameter: 35 mm Injection weight: 132 g Injection pressure: 2000 bar Metering volume: 144 ccm Clamping unit: Clamping force: 160 t Distance between tie bars: 520x520 mm Size of the clamping plates: 695x695 mm Ljdpfx Aox Nhnbjffoak Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA touchscreen Additional equipment: 2K injection molding machine with rotary table and robot Very good technical condition Operating hours: 20,181 h in automatic mode Total number of operating hours: 28,473 h Euromap 67 Robot interface Air valve x 3 Hydraulic, needle core pull, controlled by a proportional valve x 2 Reinforced injection units - bimetal Proportional valves on injection units - precise spraying Machine with two cylinders / batteries with compressed nitrogen (additional charge for fast work) Parallel movements Screw diameter in the vertical spraying unit: ⌀25 mm - 45 g/hp Original turntable Purchase of the turntable for an additional charge Robot Wittmann W823 Year of construction: 2015 5-axis robot: 3 axes are driven by servo motors (electric); axis C and movement A Travel in axes: X-550, Y-1400 (telescopic), Z-3500 Touch control panel The safety package for robots Robot with adapter, protective housing Purchase of the robot for an additional charge Dimensions Weight: 6720 kg Length/width/height: 4.41x1.84x3.20 m All offered machines are started by our service technicians before sale. It is possible to obtain a video of the technical tests of the selected machine or participate in live technical tests at our company in Łódź. Price: On request

Condition: excellent (used), Year of construction: 2009, Arburg 470C 1500-400 Year of manufacture: July 2009 Injection unit: Screw diameter: 45 mm Injection weight: 232 g Injection pressure: 1580 bar Dosing volume: 254 cc Clamping unit: Clamping force: 150 t Type distance: 470 x 470 mm Clamping platen size: 650 x 650 mm Ejector: hydraulic Clamping unit: hydraulic Control system: SELOGICA - touchscreen Additional equipment: Core pull control Injection unit hardened - bimetal Screw diameter can be changed Lodpjx Nhm Defx Affeak Dimensions: Weight: 4790 kg Length/Width/Height: 4.44 x 1.63 x 2.09 m Drive: Pumps/Motor: 18.5 kW Heating power: 9.4 kW Total power: 27.9 kW All offered machines are started by our service technicians before sale. You can receive a video of the technical tests of the selected machine or participate in live technical tests at our facility in Łódź. Price: Upon request