Used Fliegl Asw 268 for sale (199)

Condition: new, machine/vehicle number: ede0610378cbe39cc4883251d, empty load weight: 24,000 kg, maximum load weight: 7,550 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction 1st pair of wheel recesses after steel platform recessed in the tramline area, inclined towards the entrance, length at the bottom approx. 1400 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. If machines are to be driven where the overall height is to be checked, we request a technical data sheet for the machine types with exact details (if overall height is exceeded -> customer risk, approval required), (depending on the ground clearance under the machines, inserts in the wheel recesses may be required by the customer). Turntable with strong ball bearing slewing ring, storage box embedded in turntable front end Folding rear support 2 wheel chocks with holder Aluminum side bumper Rear spray flaps across the entire width Widenings can be extended to 3,000 mm (not in the rear slope) (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Storage compartment for wooden planks in the middle of the cargo bed Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 110 3 pairs of lashing points, 10 tons each, integrated in the floor at the front Incl. 6 pairs of lashing mushrooms at the top and sides, each 10 tons, embedded in the outer frame 1 x to neck area remaining distributed in between Distance not greater than 1200 mm 1 x rear slope 5 pairs of stake pockets embedded in the outer frame, inside 70 x 40 mm, (can be converted to 5 to. ring lashing eyes, not included) Towing equipment Trailer turntable Ijdpfxsi Ri Rye Ah Njht Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable, Attention: The trailer may only be towed by towing vehicles which guarantee the effectiveness of the ABS! Wheels and tires 235 / 75 R 17,5 at the choice of the manufacturer Twin steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front area steel floor, incl. Afterwards with 70 mm softwood floor, steel/checker plate covering in the wheel housing area Rear slope with 70 mm softwood floor Low loading area incl. rear slope 8 200 mm Drive-on ramps Steel ramps 2,800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. cannot be achieved. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany Incl. with

Condition: used, empty load weight: 3,850 kg, maximum load weight: 14,150 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 08/2011, next inspection (TÜV): 12/2025, loading space length: 6,900 mm, loading space width: 2,480 mm, loading space height: 1,000 mm, suspension: air, tire size: 235/75R17.5, color: grey, mileage: 1,001 km, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, 2 axles, BPW axles, turntable, air suspension, ABS (anti-lock braking system), underrun protection, side aluminium guard, twin tyres, toolbox. Iedpfxsxpxr Is Ah Neht Body: Platform with 4 removable stakes, loading height 1000mm, 2x 9t BPW axles, drum brakes! Technical inspection valid until 06/2026, good condition! Accessory information is provided without guarantee; changes, interim sale and errors excepted!

Condition: used, empty load weight: 3,140 kg, maximum load weight: 14,860 kg, first registration: 07/2022, next inspection (TÜV): 12/2023, total width: 25,500 mm, suspension: air, tire size: 385 / 55 R 22.5 / 14mm, front tire size: 385 / 55 R 22.5 / 14mm, operation weight: 18,000 kg,

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 50 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69803 Fliegl, SDS01 * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air connection couplings (red and yellow) Ihsdpfsw A Hmcsx Ah Not * 15-pin connector plug * Lifting and lowering mechanism * Suspension: Air * Total weight: 38,000 kg * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible total weight: 38,000 kg * Axle manufacturer: SAF * Tyre condition 1st axle: 70% – 70% – Tyre size: 385/55 R22.5 * Tyre condition 2nd axle: 30% – 30% – Tyre size: 385/55 R22.5 * Tyre condition 3rd axle: 50% – 50% – Tyre size: 385/55 R22.5 * Tyre sizes: 385/55 R22.5 * Fliegl container chassis * 40" container platform for timber and metal, manufacturer: S Grabmeier * Unladen weight: 4,600 kg, front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm, wooden superstructure with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Special features: Lift axle / timber transport / SAF axle Disclaimer: Subject to change, prior sale and errors excepted. More photos and videos can be found on our website. Our comprehensive services include for example: * Purchase / sale / rental of commercial vehicles * Fast, easy financing options * Processing of all (export) documents * Ordering of export plates / customs plates * Vehicle preparation: new tarpaulins, signage, painting, etc. * Professional loading / cargo securing * TÜV inspections, registration services * Transfer of commercial vehicles Ask our trained staff, we are happy to advise you.

Condition: used, empty load weight: 7,950 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 03/2013, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,850 mm, loading space volume: 95 m³, tire size: 385/55 R22,5, wheelbase: 1,310 mm, color: black, Equipment: ABS, Disc brake EBS Payload 27,050 kg Ihjdpfeuiytlex Ah Net Air-lift suspension Roll-up tarpaulin Platform SAF axles Alcoa aluminum rims Lifting and lowering device Lashing rings Errors excepted

Condition: used, maximum load weight: 27,290 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 05/2020, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,853 mm, Equipment: ABS, SDS390 101m³ X-TRA Long moving floor lift axle SAF* Deutscher Anhänger / German Semitrailer * 101m³ X-TRA Long model * SAF axles * Lift axle * Disc brakes / Discbrakes * Floor Sliding floor with rear wear plate made of V2A sheet metal, aluminum floor boards, 8 mm floor profile, ribbed design, aluminum end caps* Tires: 385/55 R 22.5 1st axle 9/9 mm, 2nd axle 12/10 mm, 3rd axle 11/9 mm * Empty weight: 7,710 kg * Permissible total weight: 35,000 kg * Payload / Working load: 27,290 kg * Air suspension * All data without guarantee * Further information and criteria on request. Ijdpferwvl Tox Ah Neht * Additional service Leistungen / Additional service * Umlackierungen, Nachrüstungen möglich / repainting, retrofitting possible * Kurzzeitkennzeichen / Zollkennzeichen / License plate * Überführung und Verschiffung möglich / Transfer and shipment possible * Hilfe bei Zoll und Export Dokumenten / Help with customs and export documents * Besorgung von COC und EUR Dokumenten / Procurement of COC and EUR documents * Seit 1991 auf dem Markt / Since 1991 on the market * Leasing and financing possible. We have been working with various leasing companies for many years and can therefore find the optimum financing for every customer. We can also often support customers with poor credit ratings and put them in touch with good leasing partners. * Own workshop / own workshop * Mówimy po polsku. * We speak english. * Goworim po russki * The repainting in your desired color is possible in our company at a reasonable price and in good quality. The repainting in your desired color is possible in our house at a reasonable price and in good quality. * Are you further away and have no opportunity or time to inspect and test a truck at our premises? No problem, you are welcome to appoint an independent expert of your choice to inspect the truck technically and visually. If, contrary to expectations, a defect should occur, we can rectify the defect quickly and effectively in our workshop. We can also deliver your new used truck anywhere in Europe for an additional charge. You are further away and have no possibility or time to visit and check a truck with us? No problem, you are welcome to order an independent expert of your confidence and have the truck checked technically and visually. If, contrary to expectations, a deficiency should occur, we can fix it quickly and effectively in our workshop. Furthermore, we can deliver your new used cars for a surcharge Europe-wide.

Condition: new, machine/vehicle number: 8b1f4087611d72661dc0b3869, empty load weight: 4,500 kg, maximum load weight: 27,500 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, in basic lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder Underride guard, folding Half-shell mudguards Tarpaulin pole with bracket Tow hook at the rear Axles+suspension SAF disc brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides Ihedpfx Asi Ri Nfeh Net 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Round steel body in Stone Master design made of highly wear-resistant HB 400/450 steel. Sloping front wall with external hydraulic en with access to front wall. Greenline - conical and aerodynamic body shape Bucket and brush holder on the outside of the front wall. Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. 2 clamping screws with toggle fasteners at the bottom side. Side walls 4 mm thick throughout, base 4/5 mm thick, wear and weight-optimized design, Standing platform with step, connection plate for air/electric and brake with large clearance for optimum operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 Body strength according to EN 12642 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear Paint finish Frame DB 7350 nova gray10-year warranty against rusting through Support legs coated black Body RAL 7035 light gray Fliegl StoneMaster advertising on the sides and rear Roll-up tarpaulin RAL on request, single color Available thermally insulated version: Cover BA

Condition: new, empty load weight: 6,060 kg, maximum load weight: 17,940 kg, overall weight: 24,000 kg, axle configuration: 3 axles, color: silver, gearing type: other, driver cabin: other, Equipment: ABS, Vehicle location: Bovenden, beacon, 3 axles, SAF axles, turntable, leaf suspension, ABS (anti-lock braking system), extendable to 3m, lashing rings, 2-part loading ramps, mechanical ramps, extendable drawbar, side aluminium underrun protection, twin tyres, EBS. Body: Loading length approx. 8.5m, extendable to 3.05m. Demonstration vehicle! Isdpfx Ajxbttqjh Nsht Parabolic suspension with axle compensation at the rear, 3x 10t SAF axles, permissible gross weight up to 30t, drawbar adjustable in length. ACCESSORY DETAILS WITHOUT GUARANTEE, subject to change, prior sale, and errors excepted!

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 60 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69805 Fliegl, SDS01 Ihedpfx Ahowzg Iws Nst * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air line coupling head (red + yellow) * 15-pin connector plug * Raise and lower device * Suspension: Air * Gross weight: 38,000 kg * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible gross weight: 38,000 kg * Axle manufacturer: SAF * Tire condition, 1st axle: 70% -- 70% - Tire size: 385/55 R22.5 * Tire condition, 2nd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire condition, 3rd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire sizes: 385/55 R22.5 * Fliegl container chassis * 40" container platform for timber & metal, manufacturer: S Grabmeier * Unladen weight: 4,600 kg, front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm, timber body with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Highlight: Lift axle / timber transport / SAF axles Disclaimer: Subject to change, prior sale, and errors excepted. You can find further photos and videos on our website. Our comprehensive service portfolio includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, straightforward financing solutions * Application for all (export) documentation * Ordering of export/temporary customs license plates * Vehicle preparation: new tarpaulins, lettering, repainting, etc. * Professional loading and load securing * TÜV inspections, registration service * Transfer of commercial vehicles Please contact our trained specialist staff—we will be happy to advise you.

Condition: used, empty load weight: 7,950 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 01/2013, loading space length: 13,500 mm, loading space width: 2,470 mm, loading space height: 2,850 mm, loading space volume: 95 m³, tire size: 385/55 R22,5, wheelbase: 1,310 mm, color: black, Equipment: ABS, Disc brake EBS Payload 27,050 kg Air-lift suspension Roll-up tarpaulin Platform SAF axles Ihodpfxsuiyvys Ah Not Alcoa aluminum rims Lifting and lowering device Lashing rings Errors excepted

Condition: used, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 05/2013, Equipment: ABS, Fliegl walking floor * EZ 22.05.2013 * 3 axles * 92 cubic meters * 1st axle lift axle * 1 vehicle owner / 1 owner * German trailer / German walking floor * Empty weight: 7,525 kg * Permissible total weight: 35,000 kg * SDS 350 * Tires: * 1st axle 385/55 R 22.5 v.l. 5 mm & v.r. 8 mm * 2nd axle 385/55 R 22.5 v.m.l. 10 mm & v.m.r. 9 mm * 3rd axle 385/55 R 22.5 h.l. 5 mm & h.r. 8 mm * All information without guarantee * The HU/SP will be renewed before the sale / We renew HU/SP ("TÜV") before Sale Iodpfoqk Tf Tjx Ah Neht * Further information and criteria on additional services * Repainting, retrofitting possible * Short-term license plate / Customs license plate * Transfer and shipment possible * Help with customs and export documents * Procurement of COC and EUR documents * On the market since 1991 * Leasing and financing possible * Own workshop * Mówimy po polsku. * We speak English. * Goworim po russki * The repainting in your desired color is possible in our house at a reasonable price and in good quality. * You are further away and have no possibility or time to visit and check a truck with us? No problem, you are welcome to order an independent expert of your confidence and have the truck checked technically and visually. If, contrary to expectations, a deficiency should occur, we can fix it quickly and effectively in our workshop. Furthermore, we can deliver your new used cars for a surcharge Europe-wide.

Condition: new, machine/vehicle number: dd98a7658922be8f2e25bcadb, empty load weight: 2 kg, maximum load weight: 8 kg, overall weight: 10 kg, axle configuration: 2 axles, tire size: 235/75 r 17,5, Further information Chassis central axle trailer low bed Fine-grained steel welded construction Telescopic front support leg Telescopic rear support 2 wheel chocks with holder Mudguards made of sheet steel over both wheels Towing device central axle trailer Tow bar with tested 40 mm towing eye Ijdpfxoi Ri Ebe Ah Noht Height-adjustable drawbar via spindle, max. adjustment range 250 mm Axles + suspension Euro axles of our choice, with angular roller bearings and S-cam brake Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings and mechanical axle load compensation (rocker compensation) Wheels and tires 235 / 75 R 17,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-applied parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, TTS bridge Low-lying steel trough, bridge floor made of steel/checker plate covering, steel walls solidly welded to floor Bridge length 4500 mmTub at the front and sides with Load-Lock profile for attaching tensioning straps (8 straps at the front, 12 straps on each side) Note: Slight floor undulation possible due to welding distortion! 2 pairs of lashing eyes, 1 x at the front in the corners of the steel tray and 1 x at the rear in the floor, 5 tons each. 2 additional pairs of lashing eyes in the floor, 5 tons each Drive-on ramps Steel ramps 2 300 mm long, 510 mm wide, can be moved sideways with grab handle on the ramps covered with wood With gas pressure jack for one-man operation Operating instructions The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Country of registration: Germany with Dekra approval and expert opinion (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paint finish Frame RAL 3002 carmine red Hot-dip galvanized drive-on ramps Attention: Archive pictures!

Condition: used, empty load weight: 5,100 kg, maximum load weight: 32,900 kg, overall weight: 38,000 kg, axle configuration: > 3 axles, first registration: 08/2018, suspension: air, tire size: 385/55 22,5, tire condition: 60 %, color: other, Year of construction: 2018, front tire size: 385/55 22,5, rear tire size: 385/55 22,5, driver cabin: day cab, emission class: none, Equipment: ABS, truck registration, Reference number for inquiries: 69804 Fliegl, SDS01 * Year of manufacture: 2018 * ABS, Anti-lock Braking System * EBS, Electronic Braking System * Air suspension * Lift axle * Air connection coupling head (red + yellow) * 15-pin connector plug * Lifting and lowering device * Suspension: Air * Gross weight: 38,000 kg * Unladen weight: 5,100 kg * Payload: 32,900 kg * Permissible total weight: 38,000 kg * Axle manufacturer: SAF Iedpfx Ahowzg Iqo Nsht * Tire condition, 1st axle: 70% -- 70% - Tire size: 385/55 R22.5 * Tire condition, 2nd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire condition, 3rd axle: 50% -- 50% - Tire size: 385/55 R22.5 * Tire sizes: 385/55 R22.5 * Fliegl container chassis * 40" container platform for wood & metal * Manufacturer: S Grabmeier * Unladen weight: 4,600 kg * Front wall height: 2,040 mm * 6 pairs of lashing rings for rail transport * Frame height: 500 mm * Timber body with 8 pairs of Ecco Steel stanchions on container chassis * Stanchion height: 1,980 mm * Highlights: Lift axle / Timber transport / SAF axle Disclaimer: Subject to change, prior sale, and errors excepted. You can find more photos and videos on our website. Our comprehensive service includes, for example: * Purchase / sale / rental of commercial vehicles * Fast, straightforward financing * Processing of all (export) documents * Ordering of export license plates / customs plates * Vehicle preparation: new tarpaulins, lettering, painting, etc. * Professional loading / load securing * TÜV inspections, registration service * Vehicle transfer of commercial vehicles Please contact our trained staff – we will be happy to advise you.

Condition: new, machine/vehicle number: 92df8e9d6c187f34b20298f39, empty load weight: 4,900 kg, overall weight: 35,000 kg, axle configuration: 3 axles, tire size: 385/65 r22,5², Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented Telescopic support in the middle, unhitching with load not possible, when unhitched the vehicle must be at an angle to the rear. 2 wheel chocks with holder Folding underride guard Half-shell mudguards Integrated mudguard holder Stone-repellent surface with anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system Ihedpfei Riz Rox Ah Njt 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 years

Condition: new, machine/vehicle number: c3dd8c834afed73501f8074af, empty load weight: 3 kg, maximum load weight: 20 kg, overall weight: 24 kg, axle configuration: 3 axles, tire size: 385/55 r22,5, Further information Chassis Changing turntable Ihsdpfoi Riylex Ah Nst Fine-grained steel welded construction Front stop, longitudinally adjustable and foldable 2 pairs of removable guide rollers, front and rear 4 container locks with sturdy outriggers on 20-basefor swap bodies 7.15 and 7.45 Turntable with strong ball bearing slewing ring 2 wheel chocks with holder Aluminum side bumper Steel underride guard Front half-shell mudguards and rear half-shell mudguards 2 stainless steel storage box, w=600/h=400/t=500 mm, with polished door, lockable 1 pair of warning signs, double LED illuminated, extendable to 3,000 mm at the rear, rear only 1 preparation plug for retrofitting warning signs at the front for customers Towing equipment Trailer turntable Drawbar with tested 40 mm towing eye Drawbar mechanically adjustable in length by 6 x 100 mm and lockable (drawbar length approx. 1,900 - 2,500 mm) Drawbar height adjustment via spring Axles + suspension BPW disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension with lift & lower valve Wheels and tires 385/55 R22,5 manufacturer's choice Factory silver steel rims Brake system 2-line compressed air brake system Spring-loaded parking brake 2 interchangeable clutch heads at the front, with connecting cables to the motor vehicle, EBS, electronic brake system with EBS plug at the front, with connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear Removable rotating beacon 1 additional LED work light(s) at the rear, switched via reversing light 2 LED work lights on both sides (1x left, 1x right) (switched via reversing light) 1 x 15-pin plug at the front, with connecting cable, Country of registration / plates Country of registration: Germany with Dekra approval and certificate (according to §13 EG - FGV) 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips in accordance with ECE R 048, white at the sides and red at the rear Paintwork Hot-dip galvanized frame incl. passivation 15-year warranty against rusting through Drawbar KTL black

Condition: new, machine/vehicle number: 068983c41e44eb5660fa9100c, empty load weight: 6 kg, maximum load weight: 28 kg, overall weight: 35 kg, axle configuration: 3 axles, tire size: 435/50 r19,5, Further information Chassis saddle forwarding Fine-grained steel welded construction, with preload slight pre-tensioning in the neck area, saddle plate with replaceable 2 kingpins Ihedpoi Riwujfx Ah Not X-tra Long, with 15030 mm internal length Outer frame slightly inclined new design with Load-Lock profile for tensioning strap attachment 24 to. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation Note: Free support leg corner dimension or free swing-through radius to the rear approx. 1930 mm Extension ladder at the rear Door retainer at the side 2 wheel chocks with holder Aluminium side bumper Galvanized steel underride guard Quarter-shell mudguards in front of 1st axle and behind each axle Impact protection at the rear Axles + suspension SAF disc brake axles Axle/chassis laser-measured Reduction of tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Colored line routing for easy service. Spring-loaded parking brake 2 interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system AAC Basic, automatic relief axle acting on last axle, as maneuvering aid, up to 20 km/h, can be switched off manually Axle load detection via EBS-Canbus signal, for indication via display in driver's cab, truck must be prepared accordingly, no truck installation (no calibrated scales) Wheels and tires 435/50 R19.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side Side amber LED lighting coupled with the blinker Flashing side lights Side lights 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Floor Screen printing plates approx. 30 mm thick, on longitudinal beams for high point load capacity for forklift axle load up to max. 7100 kg Front wall / front corner stanchions 2,580 mm high, steel corner stanchions in volume design, release device for side tarpaulin on bulkhead, crash blocker, bottom inside at approx. 140 mm height with steel impact protection Center stanchions 3 pairs of sliding stanchions can be moved along the entire length, with 4-fold pockets and with long pocket at the bottom. 3 pairs of stanchion positions Insertion slats 5 rows of wooden slats Rear wall / rear corner stanchions Rear corner stanchions steel up to lower edge of roof, attachment for tarpaulin with round tube and tarpaulin tensioning ratchet Rear portal doors, 2-leaf with 2 internal espagnolette locks each Tarpaulin Tarpaulin, with welded-in horizontal and vertical straps Stainless steel tension locks Roof Sliding roof, rear end lift can be folded up, with roof can be pushed from rear to front, L-shaped roof rail for automotive industry, internal width between the roof rails approx. 2,490 mm, tarpaulin color: white Roof non-elastic, hardly any deflection of the roof rail when loading and unloading EcoLift - lifting roof can be raised by approx. 380 mm, on both sides, with gas pressure damper support, 3 driving positions at the front: Front interior height approx. 2900 mm / 2950 mm / 3000 mm, adjusted to approx. 3000 mm Optimum rain strip at the rear, at the top of the end bows,

Condition: used, machine/vehicle number: 28be789c7675b811b702c6cb3, empty load weight: 6,000 kg, maximum load weight: 20,000 kg, overall weight: 26,000 kg, axle configuration: 2 axles, first registration: 04/2018, tire size: 205 / 65 r 17,5, Further information Welded fine-grained steel construction, saddle plate with replaceable 2 king pins Reinforcer mounting point for gallows mounting and with sturdy grinding plates drum profile made of flat steel underneath the outer frame. Outer frame slightly inclined with Load-Lock profile for attaching tension beltsNote! To attach the belts in conjunction with drop sides, the drop sides must be opened! 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Wheel chocks with holder, aluminum side bumpers, offset inwards as far as technically possible, steel underride guard, as much ground clearance as possible, quarter-shell mudguards in front of and behind each axle, suspension strip for aluminum ramps at the rear, plastic toolbox, with shelf, w=620/h=360/t=440 mm, lockable with a padlock. (lock not included in scope of delivery) SAF drum brake axles, with axle stopsAxle distance 1600 mm, air suspension with lifting & lowering valve 205 / 65 R 17.5, twin steel rims, factory silver 2-line compressed air brake system, spring-loaded parking brake, 2 interchangeable front coupling heads, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! 24 volt, multi-chamber lights, amber LED lighting integrated in outer frame profile at the side, offset inwards by approx. 25 mm, 10 lights per side 2 white position lights at the front, protected, 2 white/red lane departure lights at the rear, additional LED work light(s) at the rear, switched via reversing light Iedpfx Aemp Ug Doh Noht 2 x 7-pin and 1 x 15-pin swap-proof sockets at the front, without connecting cable Screen printing plates approx. 30 mm thick, for high point load capacity for forklift axle load up to max. 5,600 kg Special floor installation: test of new profiles, without bolting Steel/checker plate covering in the wheel arch area, front wall/front stanchions, 25 mm aluminum hollow profile, approx. 800 mm high, steel corner stanchions in volume design, with viewing windows on both sides. Approval country: Germany, with Dekra approval and certificate (according to §13 EG - FGV), 24/7 service hotline, prepared for single-line license plate holder, contour marking with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: new, machine/vehicle number: 195f80ad09517628522e33a91, empty load weight: 7,300 kg, maximum load weight: 16,700 kg, overall weight: 24,000 kg, axle configuration: 3 axles, tire size: 235 / 75 r 17,5, Further information Chassis low loader trailer Welded steel construction Turntable with powerful ball bearing slewing ring Folding rear support 2 wheel chocks with holder Aluminum side bumpers Rear splash guards across the entire width Quarter-shell mudguards in front of 1st axle 1st pair of wheel recesses after cranking, recessed in the low bed in the tramline area, slanted towards the entrance, bottom length approx. 1600 mm, approx. 400 mm deep. Note! Frame in main beam area 400 mm higher than wheel recess. 2nd pair of wheel recesses recessed between the axles in the low bed in the tramline area, sloping towards the entrance, bottom length approx. 600, approx. 300 mm deep. Note! Frame in main beam area 300 mm higher than wheel recess. Widenings extendable to 3,000 mm (not in rear bevel) Iodpsi Ri Rvefx Ah Neht (However, the track width of the construction machinery or vehicles to be transported must not exceed outer frame width 2,550 mm) Widenings extendable to 3,000 mm, also in the wheel recesses below, foldable on the wheel recess extensions, (widening not in rear sloping) (However, the track width of the construction machinery or vehicles to be transported must not exceed the outer frame width of 2,550 mm) Wooden planks 70 mm for widening to 3000 mm Low loader lashing eyes 1 pair of lashing cut-outs in the front side member, recessed on offset, 10 tons each 4 pairs of lashing holes in the outer frame, 5 tons each (lashing strap attachment) 7 pairs of lashing points at the top and sides of the outer frame, 10 tons each 1 x front on offset 6 x in the drop deck First lashing eye 250 mm from the front and last max. 250 mm from the rear, distance between lashing eyes not greater than 1100 mm Trailer drawbar Turntable Drawbar with tested 40 mm drawbar eye Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption Parabolic suspension with maintenance-free steel-rubber bearings Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, ABS and ALB, with ABS plug at the front, with connecting cable. Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Electrical system 24 volt, multi-chamber lights, amber LED lighting at the side 2 white position lights at the front 2 white/red lane departure lights at the rear 2 x 7-pin interchangeable plugs at the front, with connecting cable, 1 LED rotating beacon with holder, switched via parking light (removable light) 2 pairs of warning signs, double LED illuminated and extendable to 3,000 mm Floor Front offset with steel/ checker plate covering Storage box recessed in the drive-over slope to the offset then with 70 mm softwood floor, steel/ checker plate covering in the wheel arch area Rear slope with 70 mm softwood floor Deep loading area incl. rear slope 6500 mm Drive-on ramps Steel ramps 2 800 mm long, 750 mm wide, can be moved sideways covered with wood with spring lift support Operating instructions With an axle load of 10,000 kg, a special permit is required, only indivisible loads possible!!! The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to

Condition: new, machine/vehicle number: 83732a53562459145277be051, empty load weight: 4,200 kg, maximum load weight: 27,800 kg, overall weight: 32,000 kg, axle configuration: 2 axles, tire size: 385/65 r22.5, Further information Chassis tipper semi-trailer Fine-grained steel welded construction, lightweight design, fifth wheel plate with interchangeable 2 kingpins Curved front end Patented 24 t. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation 2 wheel chocks with holder Underride guard, folding Half-shell mudguards Integrated mudguard holder Stone-repellent surface With anti-spray flaps on last axle only 1 tarpaulin pole with bracket 2 towing hooks at the rear Axles+suspension SAF disc brake axles with 430 mm disc diameter Axle/chassis laser-measured Reduction in tire wear and fuel consumption Axles in off-road version, Air suspension 1st axle automatic lift axle, including forced lowering and starting aid, actuation of 3x brakes (starting aid is functional up to an axle load excess of 30% and up to a speed of max. 25 km/h) Hot-dip galvanized lift axle mechanism 10-year warranty against rusting through Brake system 2-line compressed air brake systemColor-coded cable routing for easy servicing. Spring-loaded parking brake 2 interchangeable front clutch heads, without connecting line EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve Vehicle stability system Automatic tilt lowering with shut-off valve Wheels and tires 385/65 R22.5 tires of the manufacturer's choice Steel rims, factory silver Electrical system 24 volt, multi-chamber lights, amber LED lighting at the sides 2 white position lights at the front Ijdsi Ri Nbjpfx Ah Njht 2 white/red rear lane departure lights 2 x 7-pin interchangeable sockets at the front, without connecting cable Hydraulics Low-pressure cylinder max. 170 bar, smallest stage hard-chlorinated, with HDK screw socket, fixed part, NW 48 mm (without hose connection). Hydraulic actuation via truck power take-off Troughs Aluminum box body made of high-quality, abrasion-resistant 5 mm thick front wall, with external walls made of 30 mm hollow chamber profiles, cleanly welded, with bulk material-repellent top rail profile. Inside with access to front wall (not in conjunction with Cramaro). Shovel and brush holder on the outside of the front wall. Greenline - conical and aerodynamic trough shape Membrane rear wall Rear wall as swing flap with double-jointed hinge, resting on the outside with double hook lock. Rear panel with rubber sealNote! Heat-resistant up to max. 170°C! Floor 6 mm thick throughout Standing platform with access, connection plate for air/electric and brake with large clearance for best possible operability. Roller tarpaulin on one side for depositing in FR-right, with central locking in FR-left Operating instructions For salt, lime, etc. We recommend a tipping cylinder with a hard chrome-plated piston rod so that it is not attacked by the material and rusts. The specified total weight is technically possible; depending on the load, the total weight may not be reached if the permissible axle/support and fifth-wheel loads are observed. (Poor driving and trailing behavior possible due to incorrect load distribution) Country of registration / plates Germany Test approval according to EC 2007/46 24/7 service hotline Prepared for single-line license plate holder Contour marking with reflective strips according to ECE R 048, white on the sides and red on the rear Paint finish Frame DB 7350 nova gray 10 J

Condition: new, machine/vehicle number: f80f2330e1318ef03bc20755e, empty load weight: 3,200 kg, maximum load weight: 35,800 kg, overall weight: 39,000 kg, axle configuration: 3 axles, tire size: 385/65 r22.5, Further information Fine-grained steel welded construction in lightweight design, saddle plate with replaceable 2 kingpins, only 2 longitudinal beams as double T-beams for retrofitting connecting gallows at the front in new/current design, outer frame slightly slanted with load-lock profile for attaching tension beltsNote! to attach the belts in conjunction with drop sides, the drop sides must be opened! 24 t. 2-speed support winch, single-sided operation, with straight lower section, without thrust compensation, wheel chocks with holder, aluminium side bumper, foldable, galvanized steel underride guard, extendable, half-shell mudguards!!! enclosed loose, not mounted!!!, with anti-spray flaps behind each axle, 1 plastic water barrel, capacity approx. 30l, in FR left BPW disc brake axles with 430 mm disc diameter, axle/chassis laser-measured Reduction of tire wear and fuel consumption, air suspension, 1st axle automatic lift axle, can also be lowered manually, can be operated with a hand button on the vehicle 2-line compressed air brake system, with 1 air reservoir central standard, spring-loaded parking brake, 2 interchangeable coupling heads at the front, without connecting cable, EBS, electronic brake system with EBS socket at the front, without connecting cable, EBS 2S/2M, test connection for brake cylinder pressure on the EBS module laid to the outside, Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS! with lifting & lowering valve, control unit + brake integrated in frame as with tipper semi-trailer, mounted in front of the axles Brake pad wear indicator for disc brakes via ABS/EBS lamp Truck 385/65 R22.5 Continental tires, steel rims, factory silver 24 volt, multi-chamber lights, amber LED lighting at the side as for tipper semi-trailer, dimension 3000 mm must be observed, 2 white LED position lights at the front, loose, 2 white/red lane departure lights at the rear, 2 x 7-pin interchangeable sockets at the front, without connecting cable Germany, test approval according to EC 2007/46 for complete vehicle, 24/7 service hotline, prepared for double license plate holder single-line1 x plastic and 1 x stainless steel interchangeable holder Ihjdpfx Aei Riwqjh Nst Warning sign according to ECE - 70, aluminum, loose, EBS, safe parking, without contour marking / reflective strips according to ECE R 048, Frame: DB 7350 nova gray, support legs: black coated Available immediately!

Condition: new, machine/vehicle number: e7fbe178b85a202cade7e95af, empty load weight: 5 kg, maximum load weight: 22 kg, overall weight: 29 kg, axle configuration: 2 axles, tire size: 235 / 75 r 17,5, Further information Chassis saddle forwarding Welded fine-grained steel construction, saddle plate with replaceable 2 king pins, with 2 king pin positions Slightly angled outer frame with load-lock profile for attaching lashing strapsNote! To attach the straps in conjunction with drop sides, the drop sides must be opened! 2 pairs of lashing eyes embedded in the outer frame on gooseneck, 5 tons each 8 pairs of lashing eyes embedded in the outer frame in the low bed, 5 tons each 24 to. 2-speed support winch, single-side operation, with straight lower section, without thrust compensation Ihedpfx Aoi Ri Hveh Nst 2 wheel chocks with holder Aluminum side bumper Steel underride guard Quarter-shell mudguards in front of and behind axle unit 2 Stainless steel stowage box, w=600/h=400/t=500 mm, with polished door, lockable 2 pairs of stake pockets recessed in the outer frame on gooseneck, 70 x 40 mm internal dimensions 6 pairs of stanchion pockets in the outer frame recessed in the deep bed, 70 x 40 mm Internal dimension!!! Internal width between the stanchions 2420 mm!!! 3 lashing/stanchion rails in the drop-down bed, embedded transversely in the floor across the entire width up to the outer frame (max. usable internal width between the outer stanchions approx. 2170 mm), approx. 100 mm high. With 20 mm round steel slats, top and bottom, distance from top to bottom approx. 60 mm (of the round steel). For lashing and inserting stanchions 80 x 80 mm. Piece of stanchions W=80/ D=50/ L=1200 mm, hot-dip galvanized Piece of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Note: Stanchion pockets / stanchions are not designed for securing long material, pipes etc. on their own without wrapping around them. Mechanical rear extension with hand crank, can be extended by approx. 1,500 mm, can be locked every 500 mm, with support beam, can be loaded with 2000 kg over the entire width at the load center of gravity at approx. 500 mm, can be loaded with 1000 kg over the entire width at 1000 mm and can be loaded with 500 kg over the entire width at 1500 mm, incl. extendable underride guard with lighting, 2 pairs of stanchions W=80/ D=80/ L=1200 mm, hot-dip galvanized Open storage compartment for stanchions, on the front wall or underneath the loading area (for 10 stanchions 80 x 50 x 1200 mm and 4 stanchions 80 x 80 x 1200 mm) Axles + suspension SAF drum brake axles Axle/chassis laser-measured Reduction in tire wear and fuel consumption last axle self-steering, with automatic reversing lock via reversing light, and additional locking function on the vehicle via hand button. Air suspension with lift & lower valve Wheels and tires 235 / 75 R 17,5 at the manufacturer's choice Twin steel rims, factory silver Brake system 2-line compressed air brake system Spring-applied parking brake 2 non-interchangeable clutch heads at the front, without connecting cable EBS, electronic braking system with EBS socket at the front, without connecting cable Attention: The trailer may only be towed by towing vehicles that guarantee the effectiveness of the ABS! Axle load detection via EBS-Canbus signal, for indication via display in the cab, truck must be prepared accordingly, no truck installation (no calibrated scales). Electrical system 24 volt, multi-chamber lights, amber LED lighting on the side 2 white position lights at the front 2 white/red rear lane departure lights 2 x 7-pin sockets at the front, without connecting cable 2 additional LED work lights, at the rear, switched via reversing light 1

Condition: new, machine/vehicle number: a0a72d14f9b44bce47bc25ffb, axle configuration: 1 axle, tire size: 11,5/80-15,3 alliance, Further information 40 mm towing eye Support leg with roller Tires: 11.5/80-15.3 Alliance without suspension Ihodpfx Aei Ri D Toh Njt Drawbar eye to center of saddle plate: 3200 mm Tire load capacity 5800kg at 30km/h + 5,150kg at 40km/h Without road approval, for internal use only!

Condition: used, machine/vehicle number: 9a9c8ebe1f7e791f4fc6f94e6, empty load weight: 2,620 kg, maximum load weight: 15,380 kg, overall weight: 18,000 kg, axle configuration: 2 axles, first registration: 04/2019, tire size: 385/65 r22,5, Year of construction: 2019, Further information Welded fine-grained steel construction, front stop, longitudinally adjustable and foldable, pair of removable guide rollers, front and rear, pair of removable guide rollers, additional 4 container locks with sturdy outriggers on 20-base for swap bodies 7.15 and 7.45, turntable with strong ball bearing slewing ring, wheel chocks with holder Aluminum side bumpers, steel underride guard, quarter-shell mudguards at the front and half-shell mudguards at the rear 1 spare wheel holder for 1 e-wheel, with wheel fastening set in basket design Drawbar with tested 40 mm drawbar eye, drawbar height adjustment via spring BPW disc brake axles, axle/chassis laser-measured Reduction in tire wear and fuel consumption, air suspension Ijdpfsi Riz Hsx Ah Nsht 2-line compressed air brake systemColor-coded line routing for easy servicing. Air supply 208 liters Spring-loaded parking brake, 2 swap-proof coupling heads at the front, with connecting lines to the motor vehicle, EBS made by Wabco, electronic brake system with EBS plug at the front, with connecting cable, (Attention: The trailer vehicle may only be towed by towing vehicles that guarantee the effectiveness of the ABS!) with lifting & lowering valve, holding function in the lowering / lifting position in each case 24 volt, 4 x 3 chamber lights + 1 round reversing light + 1 round rear fog light, amber LED lighting at the side, 2 white position lights at the front, 2 white/red lane departure lights at the rear, 1 x 15-pin plug at the front, with connecting cable, 1 additional LED work light(s) at the rear, switched via reversing light, 1 LED work light at the front in the middle between the beams, radiating to the rear, switched via reversing light Country of registration: Germany, with Dekra approval and certificate (according to §13 EG - FGV), prepared for single-line license plate holder, contour markings with reflective strips according to ECE R 048, white at the sides and red at the rear

Condition: like new (used), functionality: fully functional, machine/vehicle number: WFDFLT33901014232, empty load weight: 5,900 kg, maximum load weight: 29,100 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 07/2025, next inspection (TÜV): 07/2026, loading space length: 13,800 mm, loading space width: 2,550 mm, loading space height: 2,638 mm, suspension: air, tire size: 235/75 R17,5, color: other, Year of construction: 2025, Chassis Saddle (Spedition configuration) Fine-grain steel welded construction, fifth wheel plate with replaceable 2" kingpin. Drivable and loadable with construction/agricultural machinery up to a maximum gross weight of 24,000 kg and for construction machine widths up to 2,480 mm (however, the track width of the machinery or vehicles to be transported must not exceed 2,200 mm). Rear-mounted hook-on bracket for aluminium ramps (wider construction/agricultural machinery may not be loaded). Outer frame, slightly angled, new version featuring "Load-Lock profile" for attaching tie-down straps. 14 pairs of recessed lashing rings in the outer frame, each rated to 2.5 t. 6 pairs of recessed lashing rings in the outer frame, each rated to 5 t. 24 t, 2-speed landing gear, single-side operation, with straight lower section, without compensation for push. Free landing gear corner dimension or free rear swing radius: approx. 1,920 mm. Foldable rear support. 2 wheel chocks with holders. Aluminium side underrun protection. Steel rear underrun protection. Quarter-shell mudguards in front of and behind each axle. With anti-spray mud flaps behind each axle. 1 spare wheel holder for 1 spare wheel including mounting set. 1 spare wheel, identical brand to primary tires, steel rim. Axles & suspension: SAF drum brake axles. "Axles/chassis laser measured" to reduce tyre wear and fuel consumption. Air suspension. 1st axle with automatic lift axle, additionally electrically operated from the truck, including forced lowering and starting aid, no truck installation required (starting aid operates up to 30% axle overload and max. speed of 25 km/h). Brake system: 2-line compressed-air braking system. Color-coded wiring for easier maintenance. Spring-actuated parking brake. 2 non-interchangeable coupling heads at front (without connecting lines). 24 Volt EBS (Electronic Braking System) with EBS socket at front, no connection cable. Note: The trailer may only be towed by towing vehicles that guarantee the functionality of the ABS! Including lifting & lowering valve. Vehicle driving stability system. "TPMS" Tire Pressure Monitoring System according to ECE R 141, display through the towing vehicle via EBS, without truck installation (requirement must be present in the truck; only on standard tires). Wheels and tires: 12x 235/75 R17.5 twin tires. Isdjxb D Swjpfx Ah Noht 12x steel rims, factory silver. Electrics: 24 Volt, multi-chamber lights, yellow LED side lighting. Yellow LED side lighting linked to indicator—flashing side marker lights. 2 white LED position lights at the front. 2 white/red lane marker lights at the rear. 2 x 7-pin non-interchangeable sockets at the front, without connection cable. Floor: Phenolic resin-coated plywood panels, approx. 30 mm thick, designed for high point load, suitable for forklift axle loads up to max. 5,600 kg. Front bulkhead / corner stanchions: 25 mm aluminium hollow profile, 1,350 mm high, corner stanchions in high-volume steel version. Bulkhead additionally fitted with 1,250 mm high phenolic resin-coated plywood panel on the inside.

Condition: like new (used), functionality: fully functional, machine/vehicle number: WFDFLT33902036561, empty load weight: 5,820 kg, maximum load weight: 29,180 kg, overall weight: 35,000 kg, axle configuration: 3 axles, first registration: 04/2025, next inspection (TÜV): 04/2026, loading space length: 13,650 mm, loading space width: 2,480 mm, loading space height: 2,740 mm, suspension: air, tire size: 385/65 R22.5", color: red, Year of construction: 2025, Chassis Semi Trailer Transport Company Fine-grain steel welded construction in lightweight design, fifth wheel plate with replaceable 2" king pin Outer frame slightly slanted, new version with "Load-Lock profile" for lashing strap attachment 3 pairs of additional lashing rings embedded in the outer frame, each rated at 2.5 t 14 pairs of additional lashing rings embedded in the outer frame, each rated at 2.5 t 24 t two-speed landing gear, single-sided operation, with straight base and travel compensation SAF brand Note: Free landing leg corner dimension or rear swing clearance approx. 1930 mm Pull-out ladder at the rear Door retainer on the side 2 wheel chocks with holders Aluminum side underrun protection Painted in RAL 3002 carmine red No liability/paint warranty for overpainted coated attachments. Steel rear underrun protection, galvanized Painted in RAL 9010 pure white, including rear underrun holders No liability/paint warranty for overpainted coated attachments. Quarter shell mudguards in front of and behind the axle assembly With anti-spray mud flaps per EU regulations Rear impact protection 1 aluminum ladder approx. 2,550 mm, with holder on the side, behind the side underrun protection Insert rail on the outer frame for direct tarpaulin tensioner attachment, bolted version approx. 15–20 mm above the loading surface, upper part with perforated profile for lashing strap attachment, Load Lock outer frame must be usable (no lashing rings). Can be used together with aluminum insert slat at bottom as stop! (not in combination with drop sides) 2 plastic toolboxes, w=800/h=450/d=450 mm 1 each on the left and right of the front frame, behind the 3rd axle Axles & Suspension BPW disc brake axles with 430 mm disc diameter Wheel hubs painted in RAL 3002 carmine red "Axles/chassis laser-aligned" for reduced tire wear and fuel consumption Air suspension Brake system 2-line compressed air brake system Color-coded lines for easy service Spring-loaded parking brake 2 mix-proof coupling heads at the front, without connecting line 24 Volt EBS by Wabco, electronic braking system with EBS socket at the front, without connecting cable Note: The trailer may only be towed by tractors that ensure the effectiveness of the ABS! With raising & lowering valve + auto-reset function Vehicle stability control system Telematics Idem, incl. LIN battery, coupling sensor and tracking (without contract; customer must arrange agreement). Wheels and Tyres 385/65 R22.5" make according to manufacturer’s choice Polished Alcoa Dura-Bright aluminum rims Electrics 24 Volt, multi-chamber lights, side amber LED lighting Ihsdpfx Aoxbzkksh Net Lamp carrier painted in RAL 9010 pure white No liability/paint warranty for overpainted coated attachments. 2 white marker lights at the front 2 white/red lane departure lights at the rear Two 7-pin and one 15-pin mix-proof sockets at the front, without connecting cables LED work lights on both sides operated via reverse gear Positioned at level of first crossmember behind landing legs 2 additional LED work lights at the rear, operated via reverse gear Tarpaulin Tarpaulin with welded horizontal and vertical straps Customer lettering on rear portal, vehicle currently without tarpaulin