Used Delem for sale (217)

Condition: new, pressure 80.0 t chamfer lenght 2600 mm distance between columns 2200 mm column arm 250 mm ram stroke speed 90.0 mm/sec work speed 7.5 mm/min return speed 60.0 mm/sec work stroke 160 mm dayligth 380 mm Iodpfxexaafwo Affotr table height 900 mm oil volume 150 ltr. voltage 400 Volt weight 5227 kg range L-W-H 3750 x 1950 x 2400 mm Furnishing: - DELEM - CNC control model DA-58T - controlled axes: Y1 - Y2 and X - AKAS laser in front of the machine - manual crowning - Upper tool, deer foot - Lower tool, die block with 4Vs - SICK light barrier behind the machine - 2 front support arms - SIEMENS - electrical system - BOSCH / HOERBIGER hydraulic system - CE mark / declaration of conformity - Operating manual: machine and control - Safety manual: press brakes

Condition: good (used), Year of construction: 1997, machine/vehicle number: 887043, Offer 24557 Technical data: - max. working length 4060 mm - column clearance 3680 mm - max. pressing force 1700 kN - max. distance table / ram 385 mm - column projection 410 mm - ram stroke 215 mm - stroke speeds - downward speed idle max. 200 mm/sec - upward speed 135 mm/sec - downward pressing speed 1 to. 11 mm/sec - Total drive power 30 kW - Space requirement approx. W 5600 x H 3000 x D 2400 mm - Weight approx. 18000 kg - with: - with 6-axis CNC control DELEM - Two-hand control panel with foot switch - Crowning device - Controlled back stop with height adjustment 5 - 860 mm - Hydraulic upper + lower tool clamping - Die table displacement pneumatically supported Iedsu T Nknjpfx Affetr

Condition: used, Year of construction: 2004, machine/vehicle number: P020504, control type: CNC control, degree of automation: semi-automatic, actuation type: hydraulic, controller manufacturer: Delem, controller model: DA-66W, bending force (max.): 130 t, working width: 3,150 mm, stroke length: 350 mm, throat depth: 500 mm, distance between stands: 2,600 mm, installation height: 550 mm, operating speed: 10 mm/s, reverse speed: 115 mm/s, number of axes: 6, table height: 950 mm, type of crowning: CNC-controlled, oil tank capacity: 160 l, travel distance X-axis: 500 mm, back gauge adjustment: CNC-controlled, back gauge speed R-axis: 100 mm/s, back gauge travel distance R-axis: 160 mm, overall weight: 13,500 kg, total length: 2,300 mm, total width: 4,000 mm, total height: 3,100 mm, power: 15 kW (20.39 HP), input voltage: 400 V, input current: 35 A, input frequency: 50 Hz, Equipment: CE marking, documentation/manual, emergency stop, european tool clamping system, lower tooling, safety light barrier, upper tooling, Offered Machine: Used CNC Hydraulic Press Brake Manufacturer: CR Electronic Model: GOLD 130/31 Year of manufacture: 2004 Control: Delem DA-66W (8-axis capable) Condition: used, fully functional (Z-axes currently out of service, see below) Technical Specifications: - Press force: 1,300 kN (130 t) - Bending length: 3,100 mm - Distance between uprights: 2,600 mm - CNC-controlled axes: Y1, Y2, X, R, Z1, Z2 (Note: Z1 and Z2 are currently electronically out of service – new servo drives required. Manual movement possible.) - Stroke: 350 mm - Installation height: 550 mm - Throat depth: 500 mm - Backgauge (X): 600 mm - Table height: 950 mm - Working speed: 10 mm/s - Return speed: 115 mm/s - Motor power: 11 kW - Operating pressure: 275 bar - Weight: approx. 13,500 kg Equipment & Features: - CNC-controlled hydraulic crowning - System tool holders top & bottom - Manual quick clamping of upper tools - Laser optical finger guard (safety light curtain) - PLC-supported diagnostic system - 2 support arms with quick adjustment - Operating manuals available - CE compliant Itsdpfx Ajw A Rggeffsr Including accessories: - Fully equipped tool cabinet - Upper tool 88°, full machine length - Upper tool 35°, full machine length - Round bending upper tool - V8 T-die, full machine length - V12 T-die, full machine length - Flattening die, approx. 2,000 mm length Condition / Remarks: - Machine is in well-maintained condition, currently connected - Inspection and test run under power possible on site - Z1/Z2 currently not operational – new servo drives required - Machine is being replaced due to a planned modernization involving the acquisition of a new press brake. Price: €26,500 net (plus VAT) Negotiable for quick and straightforward purchase.

Condition: excellent (used), functionality: fully functional, Year of construction: 1995, Fasti CNC pressbrake Model 904 - 50/20 Year : 1995 Capacity : 2050 mm. x 50 tons CNC control : Delem DA 23 e - 6 axis 2 hand control and footpedal Front arms Angle punch : 2000 mm. in segment Gooseneck punch : 2000 mm. in segment Itedpfx Afexdahgofjr Gooseneck punch : 1000 mm. V die : 10 - 15 - 22 mm. in 2000 mm. V die : 30 - 40 mm. in 1000 mm.

Condition: excellent (used), Year of construction: 1984, Machine in good and neat condition. Easy to operate Delem back gauge control. Cutting gap manually adjustable. Back gauge spindles/nuts overhauled. Itjdpfx Afjiivxfefsr Specifications: Cutting length 1250mm Cutting capacity 4mm steel Delem backgauge controller Strokes/hour counter Year of manufacture 1984

Condition: not inspected (used), Press brake Darley Type EHP 260.43/37 Iedpfx Asuhf Tzoffotr year of construction 1992 converted to Delem control DA-56s Without light barriers, does not comply with current UVV regulations CNC back gauge Pressing force 2600KN Motor power 18.5 KW Working width max. 4300mm throat 300mm Weight approx. 23,000kg The offer is aimed exclusively at traders within the meaning of §14 BGB No sale to private individuals!

Condition: new, pressure 400 t chamfer lenght 4100 mm distance between columns 3550 mm column arm 510 mm Iodpfx Afexaadtsfetr ram stroke speed 110 mm/sec work speed 8.4 mm/sec return speed 130 mm/sec work stroke 375 mm dayligth 650 mm table height 1000 mm table width 240 mm back stop - adjustable max. 800 mm oil volume 400 ltr. voltage 400 Volt total power requirement 30.0 kW weight 26409 kg range L-W-H 5450 x 2650 x 3470 mm ----- HIGH-SPEED hydraulic press brake with increased installation height increased cylinder stroke enlarged projection ----- Furnishing: - DELEM CNC control model DA 66T - swiveling touchscreen control unit - 7 controlled axes: Y1 - Y2 - X - R - Z1 and Z2, as well as CNC crowning - electr. controlled backgauge X-axis = 800 mm / R-axis = 250 mm - on ball screws - controlled electr. Stop fingers Z1 + Z2 - split upper deer foot tool Roleri 135.85.R08, "System A" - with additional crowning of the upper wedge - Universal die block - LEUZE light barrier behind d. machine - BOSCH / HOERBIGER hydr. Components - SIEMENS - electrical system - FIESSLER AKAS laser protection device in front of the machine (including FPSC) - 2 front support arms with SLIDING system (plain bearings) - Double foot operation - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes Special equipment including: - electrical central lubrication

Condition: used, functionality: fully functional, Year of construction: 2001, Press force 85 t, Bending length 2050 mm, Distance between uprights 1750 mm, Control DELEM, Stroke 215 mm, Throat depth 410 mm, Total power 13 kW, Weight 8,750 kg, Machine dimensions 3190 x 2100 x 2375 mm Itjdpfx Afew Imq Rofjr

Condition: excellent (used), functionality: fully functional, Year of construction: 2021, pressing force: 40 t, BAYKAL CNC press brake Mod.: APHS-C 125040 Unused SN: 28542 YEAR OF MANUFACTURE: 09/2021 in the following version: - DELEM control system DA-58T 2D-graphics with touch screen - CNC controlled backgauge with ball screws, X-axis 750 mm + 250 mm, R-axis = 130 mm - Manual table crowning - AKAS laser safety device - Safety cover on the side and rear - 2 pcs. Front support arms on linear guides - Top system tool holder - System tool holder at the bottom - Technical documentation - CE version - Colors: * RAL 7015 - slate gray * RAL 7035 - Light gray * RAL 3003 - Ruby red Technical data: - Pressing pressure: 40 t - Working length: 1,250 mm - Motor connected load: 4 kW - Oil tank volume: 80 lt. - Departure speed: 160 mm/sec. - Working speed: 10 mm/sec. - Retraction speed: 130 mm/sec. - Folding length: 1,250 mm - Stand passage: 1,070 mm - Stand depth: 1,470 mm - Table height: 800 mm - Machine height: 2,250 mm - Installation height: 455 mm - Stroke: 215 mm - Table width: 60 mm - Projection: 410 mm Iodpfx Astz Azdoffjtr - Weight: 3,300 kg Subject to errors and prior sale!

Condition: used, CNC press brake FASTI type 904-125/30 serial no. 95-904-5775 year of construction 1995 Pressure capacity 125 ton. Working length 3050 mm Stroke approx. 335 mm Stand projection 300 mm Clearance between the side uprights 2550 mm Tool installation height max. 465 mm (opening width between the tool holders) Table width 90 mm (the clamping system is mounted on the table) Iedpfx Ajhmmfkjffotr Table height above floor 875 mm (910 mm with clamping system) Backgauge X-axis 500 mm Backgauge R-axis 115 mm Backgauge Z-axis approx. 1950 mm Lowering speed Y rapid traverse 90 mm/s Lowering speed Y-operation 8.9 mm/s Return stroke speed Y-retraction 75 mm/s Oil filling approx. 160 liters Motor power 18.5 kW Mains connection 400 Volt, 50 Hz, 20 Amp. - 7-axis CNC control DELEM type DA 58 with LCD screen - 1 axis for back gauge - stop depth (X-axis) - 2 axes for back gauge - fence height (finger R1 + finger R2) - 2 axes for back gauge - stop finger, laterally movable (finger Z1 + finger Z2) - 2 axes for press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and 2-hand control panel or 2-hand control panel only - Hydraulic tool clamping for the TRUMPF upper tool system, with 20 mm clamping groove - Hydraulic tool clamping for the lower tool with 13 mm table groove, depth 21 mm (tool pin 13 x 20 mm) - FIESSLER safety light barrier, type AKAS - 2 material support arms at the front, manually movable to the side and height-adjustable - Electrical diagram, hydraulic diagram, user manual for control available - Control cabinet on the machine - without tools Space requirement L x W x H 5000 x 2500 x 3050 mm Transport dimensions L x W x H 5200 x 1900 x 2950 mm Weight 8.5 tons. Good condition

Condition: excellent (used), Year of construction: 1999, Technical Data: Working length: 3050 mm Distance between uprights: 2690 mm Pressing force: 130 t CNC control: DELEM Adjustable backgauge Controlled axes: Z1 / Z2; X; R Itjdsw Tcncepfx Affjr CNC-controlled crowning Installation height: 535 mm Stroke: 365 mm Throat depth: 410 mm Hydraulic tool clamping top and bottom Ram position measuring system with spring-back compensation via glass scales Program-controlled lower tool shifting (I-axis) for 2 positions Motor power: 12.5 kW Number of backgauge fingers: 2 CE mark Dimensions (L x W x H): approx. 3800 x 2350 x 3150 mm Weight: approx. 14 tonnes Condition: Good condition The seller is not liable for typing or data transmission errors. The machine's appearance, technical condition and wear correspond to its age; used machines are sold without any warranty.

Condition: used, functionality: fully functional, Year of construction: 2004, control type: CNC control, degree of automation: automatic, actuation type: hydraulic, controller manufacturer: DELEM, controller model: DA 66W, bending force (max.): 250 t, working width: 5,100 mm, stroke length: 250 mm, distance between stands: 4,555 mm, number of axes: 6, back gauge adjustment: CNC-controlled, overall weight: 25,500 kg, total length: 6,500 mm, total width: 2,300 mm, total height: 3,200 mm, Equipment: CE marking, emergency stop, european tool clamping system, finger protection, foot remote control, FEATURES: Axes: R – X – Y1 – Y2, Z1, Z2 Bending length: 5,100 mm Distance between uprights: 4,555 mm Force: 250 t Throat depth: 465 mm Ram stroke: 250 mm Distance table–ram: 450 mm Control unit: Delem Weight: 25,500 kg Overall dimensions: 6500 x 2300 x 3200 mm Year of manufacture: 2004 Year of rebuild: 2021 Itedjw S Hfcjpfx Affor STANDARD EQUIPMENT: CE compliant PROMECAN pneumatic clamping Self-centring lower table with pneumatic clamping Motorised backgauge 1,000 mm (“X” axis) Height adjustment on “R” axis 250 mm CNC DELEM DA 66W 4 motorised, adjustable fingers Z1, Z2 Bending penetration (“Y1, Y2” axes) Low-voltage electric foot pedal operation Emergency stops Hydrodynamic anti-deflection table with hydraulic crowning Side guards Class IV safety laser.

Condition: used, Year of construction: 2003, pressure 45.0 t chamfer lenght 2050 mm distance between columns 1600 mm column arm 300 mm stroke 150 mm dayligth 395 mm ajustment speed 100 mm/sec working feed 1-10 mm/sec return speed 70,0 mm/sec table width 60,0 mm table height 905 mm oil volume 150 l operating pressure 340 bar voltage 400 V total power requirement 5,5 KW weight of the machine ca. 3500 kg range L-W-H 2900 x 2100 x 2420 mm good / well-maintained condition (!!) Isdsw U U Spopfx Affstr - in checked condition - machine video - ?v=f0lMBgZD1VU Furnishing: - DELEM CNC control model DA 65 * Swivel control panel, front right * 2D graphical programming & product display * Tool & program library * including new screen (installed 11/2023 .. 1.200 euros) - CNC controlled axes: Y1 + Y2 / X / R axis - CNC controlled back gauge (X axis) - CNC controlled height adjustment from the back gauge (R axis) - manual adjustment of the 2x stop fingers (Z axis) - AMADA-SYSTEM A upper tool clamping, including upper wedge crowning - AMADA SYSTEM A lower tool clamping - FIESSLER motor-adjustable laser protection device at the front (AKAS 160 S) - 1x freely movable foot switch - 2x front support arms - 1x set of AMADA-SYSTEM A bending tools - Rear safety device (lockable door) - Safety device on the side (pivoting doors) - Control instructions (PDF) + machine circuit diagram * Machine link: ?machineno=1008-9308356

Year of construction: 2023, condition: new, Standard version: - Y1, Y2, X, R (4-axis) X=650 mm X,R - Control system - CNC CYBELEC ModEva 19T - CNC controlled motorised crowning - European clamping system - throat - Sliding front support arms with T-slot and tilt stop - Rear stop: Siemens DC servo with linear guide & ball screw - Protective covers Special accessories: (Available depending on bending length and pressing force): Bending aid: - Bending aid -motor. Height adjustment - max. load 125 kg - Bending aid -motor. Height adjustment - max. load 250 kg Backgauge axes: - X=650 mm X,R,Z1,Z2 (AL) - X=650 mm X,R,Z1,Z2,Delta X +/- 125mm CNC controlled - X=650 X1,X2,R - X=650 X1,X2,R,Z1,Z2 - X=750 X1,X2,R1,R2,Z1,Z2 - X=1000 mm X,R (AL ) - X=1000 mm X,R,Z1,Z2 (AL) Control: - DELEM DA 69T - DELEM DA 66T Safety system: - CE with manual F.AKAS II M -FPSC-B-C (SAFETY PLC) - CE with FIESSLER AKAS-3P motorised + FPSC (SAFETY PLC) - CE for tandem machines FIESSLER AKAS light barrier - tandem - - preparation + safety cover with switch - AKAS 3P tools: - Various tool clamping systems as well as tools to choose from. Further options: - DAM (Durma Laser Angle Measuring System) - Air conditioning for control cabinet - additional support arms movable - Central lubrication manual - Central lubrication motorised - Control panel on the other side - additional stop fingers - oil cooler - Parking area for bending aid (1 metre) - second foot pedal Itedpfx Afen Tnn Esfer - die rail (groove 12.7 mm width, 15.8 mm height) - special painting - Tandem preparation - oil heating - laser bending line - lateral sliding doors Are you interested in exactly this machine model or do you have specific questions? Please use the contact field to send us a message. We will answer you immediately!

Condition: excellent (used), functionality: fully functional, Year of construction: 2001, Pressure: 85 t Bending length: 2050 mm Frame gap: 1750 mm Control: DELEM Stroke: 215 mm Iodpfx Aow D Abreffotr Throat depth: 410 mm Total power: 13 kW Weight: 8,750 kg Machine dimensions: 3190 x 2100 x 2375 mm

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2000, machine/vehicle number: 885669, bending force (max.): 130 t, working width: 3,050 mm, stroke length: 365 mm, throat depth: 410 mm, clearance between the columns: 2,800 mm, TECHNICAL DETAILS Pressing force: 130.0 t Working area Working width: max. 3,050 mm Max. stroke: 365 mm Throat depth: 410 mm Distance between columns: 2,800 mm Number of axes: 6 Control Control: CNC Control type: Delem DA65 Controlled axes: Y1-Y2 + X-R-Z1-Z2 + I + crowning MACHINE DETAILS Dimensions and Weight Overall length: 3,500 mm Overall width: 2,200 mm Itodpew Dqckjfx Affjr Overall height: 2,400 mm Weight: 11,000 kg EQUIPMENT WILA hydraulic clamping Angle measurement system Documentation CE marking

Condition: ready for operation (used), Year of construction: 1997, Press force: 1700kN, bending length: 4000mm, stroke: 215mm, installation height: 365mm, passage width: 3680mm, throat depth: 410mm, feed speed: 200mm/s, bending speed: 1-10mm/s, retraction rate: 135mm/s, working height: 1050mm, control: Delem. Including spare parts and accessories. Documentation available. Itedpfxstqfqio Affjr

Condition: used, Year of construction: 2019, pressure 100 t chamfer lenght 3050 mm distance between columns 3250 mm Control Delem DA 66T stroke y-axis 300 mm dayligth 590 mm ajustment speed 75 mm/sec Bending Speed 20 mm/sec. backward speed 75 mm/s total power requirement 11 kW weight of the machine ca. 6,5 t dimensions of the machine ca. 4,3x2,0x2,9 m Demonstration machine Y1 / Y2 servo electronic Hydraulic stamp clamping (WILA Premium) Hydraulic die clamping (WILA Premium) including motorized crowning Back gauge system "DENER" X-; R-; Z1-; Z2- axis FIESSLER AKAS LC II M Typ 4 (manual adjustment)with box bending Rolleri quick-change tools segmented: Itedjv R Hvnopfx Affer Punch TPR200.28.R1, die TMR100.12.30 total 3.050 mm length

Condition: new, pressure 220 t chamfer lenght 3760 mm distance between columns 3250 mm column arm 410 mm Ijdpfx Ajw U U Rreffjtr ram stroke speed 180 mm/sec work speed 10.0 mm/sec return speed 160 mm/sec work stroke 275 mm dayligth 550 mm table height 900 mm table width 160 mm oil volume 300 ltr. voltage 400 Volt total power requirement 18.5 kW weight 12906 kg range L-W-H 5100 x 2250 x 2900 mm ----- Press brake with special equipment * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - Universal die block - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: like new (used), functionality: fully functional, Year of construction: 2023, machine/vehicle number: P 648, control type: CNC control, oil tank capacity: 290 l, overall weight: 9,500 kg, power: 11 kW (14.96 HP), Built for a globally leading cooperation partner. Last machine from the pool. Machine is as good as new. The High Quality Press Brake (HQPB) is the top model among Placke press brakes. The entire manufacturing process, from the hydraulic cylinder to electrical cabinet construction, is carried out in-house. By combining state-of-the-art technology with decades of experience in forming technology, the HQPB series allows you to perform bending at the highest level. The standard configuration already provides a fully functional press brake. With this package of safety, reliability, and efficiency—paired with user-friendly operation—we are able to meet the highest demands and precision requirements in the bending process. Machine Frame: - Base machine constructed from steel S 355 N - Side frames welded with 2 pressure pipes and top-mounted oil tank - Above-floor design - Coating (2-component textured paint), light grey (RAL 7035) and signal grey (RAL 7004) Upper Beam: - Press beam stress-relieved annealed - Depth penetration measurement, reader head guided by ball roller guide - Separate Y1 and Y2 control, electrical angular misalignment monitoring Hydraulic System: - Hydraulic proportional control valve system with electronically monitored cylinder parallelism - Solid steel cylinder with inductively hardened piston rod - Low-noise internal gear pump Punch Clamping: - Upper tool holder system WILA, hydraulic clamping system, type NSCL-II-HC, fully hardened, max load: head bearing = 250 t/m, shoulder bearing = 300 t/m Lower Beam: - Narrow table incl. manual clamping bar, dimensions: 95 mm high, 95 mm wide - Centrally adjustable crowning system, WILA system, CNC controlled, NSCR-I-MC. Two mechanically adjustable wedge bars compensate for deflection - Single-V die holder (13x20) - Working height: 1050 mm (with 55 mm tool height) Front Side of the Machine: 2 aluminum support arms in the front, approx. 600 mm long, incl. 2 tilting stops, measuring tape, and plastic wear strip. The support arms are movable on a linear ball guide and can be height adjusted for 55 mm to 100 mm high dies using a slotted hole. The linear ball guide is milled into the lower beam. Control and Regulation Technology: - Operating voltage 400V / 3Ph / 50Hz - Switching and safety components by Telemecanique - Backgauge with AC servo technology - Pilz safety PLC Backgauge "2-axis controlled": - X- and R-axes CNC controlled - Z-axis manual Delem DA 66 Touch control on swivel arm incl. Profile S-Lite offline programming software. Safety equipment according to CE standards Technical Data and Working Range: Press force: 1250 kN Working length: 3100 mm Clearance between uprights: 2600 mm Installation height: 450 mm Throat depth: 305 mm Ram stroke: 265 mm Ram Speeds: Itjdpfxjw Nhhgs Affjr Rapid traverse max: 220 mm/s Pressing speed max: 9.8 mm/s Return speed max: 160 mm/s Ram positioning accuracy: ± 0.01 mm Ram tilt: ± 10 mm Electrically limited to ± 5 mm Lower beam height above floor: 900 mm Motor power: 11 kW Main Dimensions: Pit depth: 0 mm Side frame pit depth: 0 mm Machine weight: approx. 9.5 t Tank capacity (hydraulic oil): 290 l (Technical changes reserved) Lighting behind the machine: Workspace illumination using LED light strip between the uprights.

Year of construction: 1998, condition: good (used), Built in: 1998 Size: 320 x 400 mm Speed: 12.000 c/h Equipment: • main product feeder • product acceleration • suction opening unit • 3 supplement feeder • endelement with rejection Itsdpfx Afsdym Tqsfsr • control panel • stream delivery

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1999, bending force (max.): 110 t, working width: 3,100 mm, TECHNICAL DETAILS Press force: 110 t Ijdpfx Afjww E Rijfstr Bending length: 3,100 mm MACHINE DETAILS Machine weight: 10,000 kg EQUIPMENT - CNC Delem control - Side safety doors - Two-hand foot pedal - 2 support arms - Upper and lower tools - Hydraulic tool clamping - Crowning system

Condition: new, pressure 40.0 t chamfer lenght 1270 mm distance between columns 1050 mm column arm 350 mm dayligth 387 mm work stroke 170 mm table height 850 mm back stop - adjustable 800 mm adjustment speed 230 mm/min ajustment speed 140 mm/sec working feed 10.0 mm/sec return speed 170 mm/sec total power requirement 5.5 kW weight of the machine ca. 3220 kg dimensions of the machine ca. 2150 x 1650 x 2300 mm ----- Press brake with special equipment Itedsw U U Rlspfx Affor * increased installation height * increased cylinder stroke * as well as increased bending beam speeds ----- Furnishing: - DELEM CNC control model DA 58T (TouchScreen) - Motorized backgauge with R-axis, on recirculating ball spindles - X = 800 mm R = 250 mm with 2 stop fingers - controlled axes Y1 - Y2 - X - R - C (crowning) - electr. Crowning controlled by CNC - Upper deer foot tool with PS 135.85-R08, system "A" with quick-change clamp - Additional crowning device in the tool holder of the upper tool - 4V universal die block M 460 R with die shoe 60 mm holder - BOSCH / HOERBIGER hydr. Components - SIEMENS electrical system - LEUZE light barrier behind the machine - FIESSLER AKAS laser with FPSC protective device v.d. machine - Swiveling control panel, mounted on the left - 2x front support arms "sliding system", with T-slot and tilting cam - 1x double foot control - CE mark / declaration of conformity - User manual: machine and control in German - Safety manual: press brakes

Condition: new, Year of construction: 2025, The EQPB BabyPress is a hydraulically operated table model with CNC control. It is a robust and low-noise machine that has been specially developed for the production of small parts. The entire production, from the hydraulic cylinder to the control cabinet construction, takes place in-house. The advantages: - Basic C-frame design - Compact table model - Ideal for prototypes and small series - Very short set-up time - Functionally simple - Wide range of applications Standard basic design: - Upper cheek guide with high-precision roller guide - Mechanical tool clamping system Promecam - Narrow table with single V-tool holder (13x20) - CNC control Delem DA-41T - Y-axis CNC-controlled for programmed plunge depth calculation - X-axis CNC-controlled 170 mm traverse path - R-axis manual - low noise level - low power consumption - easy operation technical data: - pressing force 62 kN - working length 285 mm - clearance between the uprights 230 mm - Installation height 215 mm - throat 70 mm - ram stroke 100 mm Ram speeds: - Press stroke max. 9.8 mm/s Itjdpfxjglkfps Affer - retraction max. 50 mm/s - Motor power 0,7 kW - main dimensions (WxHxD): 900 x 1.300 x 550 mm - Machine weight approx. 0,25 t - Tank capacity (hydraulic oil) 10 l Optionally, we offer this machine without CNC control and / or a press force of 12 t, just contact us.

Condition: ready for operation (used), Size main product max 320 x 400 mm min 148 x 210 mm Size supplement min 320 x 400 mm Itjded Ir Ipepfx Affjr min 105 x 148 mm Speed max 14.000 c/h Working height feeder 1.100 mm Equipment • main product feeder • opening station with sucker and sword • 3 insert feeders • endelement with reject unit • belt delivery