Used Crankshaft for sale (83)

Year of construction: 2005, condition: used, functionality: unexamined, machine/vehicle number: 46787, 46787 Machining center for centric turning operations on crankshafts or shaft-like components with 2 independent machining spindles. Control: Siemens 840D Tool holder: Heller turning broaching wheel 45 tool positions around the circumference Tool diameter: Ø700 in nominal dimensions – tools are not included, but can be acquired or newly manufactured for an additional charge. NC-controlled steady rest supports – without steady rests Retractable 3-jaw chuck on both sides, manufactured by Blessing Automatic loading door from above with a loading interface Dedicated chip conveyor with high discharge The machine can currently be inspected while powered on. Setup of components is possible after consultation and for an additional charge, including documentation of replacement parts and tools. Safeguarding of the control system and drives is included – delivery free to site. This is the machine base of a 1250mm machine; however, the usable length is limited to approximately 680mm between centers due to the main drive shaft. With a new main drive shaft, a length of over 1050mm would be possible. Year of production: 2005 Machine for centric turning operations of crankshafts or shaft-typical parts with 2 individual machining spindles Machine control: Siemens 840D Tool adapter: Heller turning broaching wheel 45 tool positions around the circumference Tool diameter Ø700 nominal – tools are not included and may be subject to a separate purchase or new procurement from the supplier. Nedpfx Aezdpvgof Sjlg NC-controlled roller support – no workrest included Retractable 3-jaw chuck on both sides from Company Blessing Automatic gantry door for overhead loading and corresponding interface Individual chip conveyor with high drop Machine can be inspected while powered on upon request Setup of individual parts possible for a separate cost, including documentation of change-over parts and tooling Safeguarding of control and drives included – free location Machine base is DRZ1250 – effectively, on current driveshaft, limited to 680mm length; with a new driveshaft, it could be extended up to 1050mm.

Condition: used, Year of construction: 2019, operating hours: 15,551 h, functionality: fully functional, controller manufacturer: Siemens, controller model: SINUMERIK 840D sl, General Year of manufacture: 2019 Operating hours: 15,551 Control: SINUMERIK 840D sl Maximum workpiece dimensions Workpiece length up to 600 mm Maximum cutting circle mm 200 Stroke over center mm 100 Maximum clamping diameter mm 110 Tip diameter mm 30 – 60 Working area Longitudinal stroke Z-axis mm 705 Longitudinal stroke Z-/W-axis mm 705 / 705 Cross stroke X-axis mm 180 Cross stroke X-/U-axis mm 180 / 180 Nlodpfjwgm Hkex Af Seg Steady Z3-axis depends on the chuck Workpiece C21-/C22-axis degrees 360 Tool Outer diameter mm 700 Tool holder Short cone according to DIN 55026: Size: 8 Theoretical diameter of cone mm: 139,735 Tool drum bearing diameter in the front bearing: 160 mm Chuck mount: 180 mm Chuck diameter up to 260 mm Workpiece spindle bearing diameter in the front bearing: 170 mm Guidance system for machining units: Rolling guides with rollers, size 55 Spindle Maximum power at 100% load: 24 kW Spindle speed: 0-2000

Condition: used, Year of construction: 1952, workpiece length 5000 mm swing dia. 1100 mm Nlodpfx Afjyt Rxve Ssg clamping length 6000 mm grinding diameter 1100 mm grinding wheel diameter 1300 mm workpiece weight 2500 kg main drive motor 22 kW crankshaft bearing diameter 275 mm steady 100-250 mm speeds of tool 400/500 U/min workpiece turning speeds 20-40 U/min weight of the machine ca. 30 t 13 Grinding Steady Rests Mandrels Mounting Flanges Clamping Devices The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: used, Year of construction: 1981, workpiece length 1500 mm stroke 0 mm swing dia. 500 mm total power requirement 30 kW Nodot Hwpmopfx Af Solg weight of the machine ca. 8 t dimensions of the machine ca. m

Condition: used, Year of construction: 2005, Distance between centers 3050 mm Center height 280 mm Travel paths: Z-axis 2800 mm X-axis 400 mm U-axis 160 mm W-axis 160 mm Max. workpiece weight 1000 kg Grinding wheel: Outer diameter (new) 1050 mm Max. width 120 mm Bore 304.8 mm Grinding wheel peripheral speed 6-50 RPM Njdpfx Aswz Rg Dsf Sjlg Accessories: - Measuring system - Tailstock - Coolant system - Documentation

Condition: used, total width: 800 mm, total length: 2,300 mm, Meuser conventional lathe with a 3-jaw chuck, tool holder, and fixed tailstock. Robust German lathe for the workshop. Technical specifications: - Chuck: 3-jaw - Bed dimensions: approx. 160 x 74 cm - Machine dimensions: approx. 230 x 80 cm Nsdpfxozzpbwo Af Sslg - Accessories: tool holder, fixed tailstock The machine is sold in its current condition (used, from a bankruptcy sale, Apeldoorn, Netherlands). Dismantling, loading, and transport are the responsibility of the buyer; the buyer must provide their own tools, lifting/loading equipment, and packaging. Inspection is possible by appointment.

Year of construction: 1980, condition: used, The Sledum RG-270 is a high-precision, industrial-grade crankshaft grinding machine developed for the precision grinding of crankshafts in internal combustion engines and the journal surfaces of similar rotating components. The machine is built on a massive cast-iron machine bed, offering high stability and vibration damping. The design enables uniform, high-precision machining of large crankshafts. Key Technical Features: Distance between centers: 2000 mm Maximum swing radius: 270–275 mm Machinable parts: crankshafts, shafts, eccentric rotating components Nlodpezbiblsfx Af Seg Grinding spindle with high-rigidity bearings Fine-feed cross and longitudinal slide system Machine bed with precision guide rails Adjustable steady rest system for stable support of long workpieces High-power grinding motor for continuous industrial operation Manually controlled feed and positioning system Stable, vibration-damped industrial machine frame Coolant system with preparation/conditioning unit Heavy-duty industrial construction, designed for long service life Accessories and Equipment: Complete headstock and tailstock (counter-spindle) system Grinding spindle unit with grinding wheel mount Adjustable steady rests for long shafts Workpiece clamping system Precision alignment and centering components Grinding wheel mounting flanges Workpiece rotation mechanism Manually controlled operator panel Complete slide system with fine feed Coolant connection points Machine body and industrial machine bed Adjustable workpiece support units

Condition: good (used), Year of construction: 2011, LANDIS LT-2 TWIN WHEEL CNC ORBITAL CRANK GRINDER Equipped with: Landis 6400 CNC Control Siemens TOUCH HMI Arobetech Steady Rest Marposs P7 Gage System Lateral Locator Twin CBN Grinding Wheels Rotary Dresser Headstock Tailstock Nedpfx Afjrtrxxo Solg Rittal AC Units Specifications: Maximum Center Distance: 680 mm

Condition: used, Year of construction: 1980, workpiece length 2700 mm swing dia. 630 mm clamping length 2700 mm stroke position adjustment 40-130 mm grinding wheel diameter 1000 mm weight of the machine ca. 18,5 t dimensions of the machine ca. 9x4 m cyclic control CNC / Simatic S7-300 steady rest Nodpfxsyukdzs Af Selg hydraulic pre-positioning manual fine tuning (Vertical u. Horizontal) grinding wheel flanges rough turning fixture Radial- and side turning fixtures manual Radius turning fixture filtering system Polo inclined bed filter SB-A0.4 manufactured in 2012 grinding wheels storage system for 8 grinding wheels diverse machine tools steady rest jaws diverse irrigation nozzle (workpiece cooling) washer cover with edge lavage Indexierledges for quick workpiece slide position lifting device for grinding wheels manipulation diverse spare parts sliding cover left and right diving plate and clampinserts The tech. Data are manufacturer or operator information and therefore non- binding. We reserve the right to prior sale; Our terms and conditions of sale apply exclusively. About us More than 400 of our own machines in stock Over 15,000 m² of storage space, 70 t crane capacity More than 10,000 items and accessories for your workshop If you are interested in selling machines, production lines, or your business, please contact us. You can find further offers on our website. Tours are possible by appointment. We look forward to your visit. Your Markus Hirsch Team

Condition: excellent (used), Year of construction: 2003, functionality: fully functional, Equipment: documentation/manual, type plate available, Taylor Hobson Talyrond 265 roundness measuring instrument. Extremely accurate; it can measure the roundness of lenses, optics, pistons, turbine components, tubes, shafts, and also eccentricity, e.g., of cams on a camshaft or journals of a crankshaft. It is certainly of interest for motorsport and tuning companies. Nodpfozcqy Ejx Af Solg The first photo is a "representative image" from a Taylor Hobson catalog, showing how it is constructed, except for the computer, which is a newer, more modern HP model with a small form factor. Max. diameter 350 mm Max. test piece height 500 mm (higher values are possible by measuring in two parts, up to a maximum of 1000 mm...) Self-centering of the workpiece +/- 5 mm Max. weight of test piece 40 kg The system has been used very little and has had only two owners. The first owner, from whom I bought it, was an implant company in Hamburg; it was used in a "medically clean environment" and is extremely clean. It was never located in a dirty machine hall. The year of manufacture is estimated to be between 2003 and 2005. The Taylor-Hobson measurement software is, of course, included and runs on the supplied HP computer (without a password...). It is also on the USB stick, perhaps for installation on another machine at your location. Accessories are included: the original Taylor-Hobson desk, computer, monitor, seven (7!) measuring probes, each of which is very expensive to purchase. A sample/sample lens (hemisphere) is included for calibration! The very detailed operating manual is on the USB stick, and all circuit diagrams and functional diagrams are also included! The system will be shipped on two Euro pallets via a freight carrier. It is already well secured on them. The Talyrond 265 and the desk will be wrapped with bubble wrap, etc., and secured with stretch film to provide extreme protection during transport. The system itself is fixed with "transport safety screws." Shipping is at the buyer's expense and will be on two Euro pallets. The measuring system should definitely be assembled and put into operation by a Taylor Hobson service technician, who can then also recalibrate the system on-site. This is now recommended after a few years. Errors can be made during assembly and commissioning. For example, some locking screws are installed for transport, and if you forget them, the system could be damaged when starting up. A truly well-maintained, very accurate system that will continue to provide excellent service for many years to come!

Condition: used, Year of construction: 2013, feed x/z 20/40 m/min rapid traverse (x/z) 18.000 /30.000 mm/min number of tool places 12 Pos. tool taper VDI 50 In our opinion, the machine is in good used condition and can be inspected Njdpfx Afox Ik Tdj Selg under power by appointment. There are 2 machines available. Accessories, tools, and clamping devices shown are only included in the scope of delivery if noted in the additional information. Subject to changes and errors in the technical data and information, as well as subject to prior sale!

Condition: good (used), Weipert crankshaft grinding machine Weipert Grinding bench Nodoihfryopfx Af Sslg Centering point: Röhm 110 H MK5 machine length: 4300 mm Financing through our bank is also possible. komplett-konzept.leasingo.de More grinding machines in other sizes - new and used - you will find in our store! International shipping costs on request!

Year of construction: 2003, condition: good (used), Schatz Advanced Screwdriving Unit  Schatz screw machine Length: 5450 mm Height: 3000 mm Unwinding stand Length 5020 mm Njdpfx Asihiiief Selg 2 x Demag crane 1 x Liftket electric chain hoist  1 x Schatz 907500 Installation without Advantech TPC-1260 TE Touch Panel PC Financing through our bank is also possible. komplett-konzept.leasingo.de More screwdriving machines in other sizes - new and used - can be found here.

Condition: used, Year of construction: 1998, Control Siemens 840 D swing diameter over slide rest 650 mm max. turning speeds 3800 min/-1 spindle diameter in front bearing 150 mm spindle bore 92 mm spindle head A8 DIN55026 number of tool places 2x 12 Pos. tool taper VDI 40 Nodsx I Simspfx Af Solg weight of the machine ca. 7,0 t In our opinion, the machines are in good used condition Condition and can be viewed under power by appointment. Technical features: - Nominal length: 1500 mm Accesories: - chip conveyor - Felsomat loading system - lathe chuck - milling body There are 2 identical machines available. Accessories, tools and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Changes and errors in the technical data and information as well Subject to prior sale!

Condition: used, functionality: fully functional, Year of construction: 2001, operating hours: 6,500 h, machine/vehicle number: S40-5934, load capacity: 227 kg, lifting height: 15,700 mm, fuel type: diesel, Equipment: all wheel drive, Genie S45 Telescopic Boom Lift Top maintained – extensive repairs – ready for immediate use For sale is a Genie S45 telescopic boom lift in very good technical condition. The boom lift has undergone extensive refurbishment and regular maintenance in the last two years. All invoices are available and can be viewed during inspection. Technical data • Manufacturer: Genie • Model: S45 • Year of manufacture: 2001 • Operating hours: approx. 6,500 h • Working height: 15.7 m • Platform height: 13.7 m • Lateral reach: 9.65 m • Load capacity: 227 kg • Drive: Diesel • Four-wheel drive • Serial number: S40-5934 Extensive investments: In 2023, the engine underwent extensive overhaul (invoice for €9,013 gross): • Engine completely serviced • Connecting rod and crankshaft bearings replaced • Piston rings replaced • Cylinder head gasket replaced • Starter replaced • Oil, air, and diesel filters replaced • V-belt replaced • Numerous other wear parts replaced In 2024, further extensive maintenance and hydraulic work was carried out (invoice for €5,254 gross): • Swing drive motor replaced • Hydraulic pump sealed • Hydraulic hoses replaced • Hydraulic oil replaced • Engine oil and all filters replaced • Machine completely lubricated • Functional test performed • Safety inspection performed Condition • Technically fully functional • Ready for immediate use • Normal age-related signs of wear • No known defects • Inspection and test operation possible at any time by appointment. In 2023 and 2024, over €14,000 was invested in the machine. As a result, the boom lift is in significantly better technical condition than many comparable machines of this year of manufacture. Nedpfjzrgmrsx Af Solg Price: €13,900 net negotiable (16,680 € gross) Location: Laakirchen (Upper Austria)

Condition: used, Year of construction: 2017, turning length: 500 mm, spindle motor power: 30,000 W, General Year of manufacture: 2017 Control: SINUMERIK 840D sl Maximum workpiece dimensions Workpiece length up to 500 mm Maximum cutting radius mm 200 Stroke over center mm 25 Maximum clamping diameter mm 100 Tip diameter mm 30 – 60 Working area Longitudinal stroke Z-axis mm 602 Longitudinal stroke Z-/W-axis mm 602 / 602 Cross stroke X-axis mm 140 Cross stroke X-/U-axis mm 140 Steady Z3-axis depends on the chuck Workpiece C21-/C22-axis degrees 360 Tool Outer diameter mm 230 Nledpfewgndkjx Af Sog Tool holder Quick-change system Bearing diameter of tool drum in the front bearing mm 660 * 790 Chuck holder Cylindrical mm 180 Chuck diameter up to mm 260 Workpiece spindle bearing diameter in the front bearing mm 170 Guidance system for machining units Rolling guides with rollers, size 45 Feed drives Cross slide adjustment W-axis, Z-axis 100% duty cycle Nm 18 / 18 Tool feed U-axis, X-axis 100% duty cycle Nm 18 / 18 Steady Z3-axis 100% duty cycle Nm 10.5 Vise right Z4-axis 100% duty cycle Nm 10.5 Circular feed workpiece C21- axis, C22-axis 100% duty cycle Nm 18 / 18 Axis speed Feed/rapid traverse speed longitudinal W-, Z-, and Z3-axes m/min 0 - 40 Feed/rapid traverse speed transverse U-axis, X-axis m/min 0 - 20 Feed/rapid traverse speed Z3-axis (steady rest) m/min 0 - 40 Circular feed of workpiece C21-axis, C22-axis rpm 0 - 60 Cutter drive Power per unit (nominal / maximum) kW 15 / 30 Cutting speed m/min 120 - 255 Tool torque Nm 1500

Condition: used, Year of construction: 2006, Milling spindle unit SEMA SE 100, e.g. for the production of crankshafts Spindle mounting: flange Speed with this gearbox: 97 rpm Spindle designed for up to 3000 rpm Drive power, currently: 22 kW The milling spindle is designed for up to 25 kW Bearing diameter: 110 mm Disc cutter SANDVIK Ø 700 x 25 mm Plunge depth of the disc cutter: 235 mm Accessories / Special features: - Disc cutter SANDVIK Ø 700 x 25 mm - Lubricated-for-life spindle bearings - Robust construction with hardened and ground spindle - High precision - 2-fold bearing of the spindle with 5 spindle bearings - WZ clamping via flange Nodpfxeddzi Aj Af Selg Original new price at the time: approx. €34,500.00 net Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: reconditioned (used), functionality: fully functional, overall weight: 2,000 kg, shaft diameter: 175 mm, length (extended): 4,418 mm, motor model: J624GS-F, Crankshaft J624, overhauled and ready for installation. Features connecting rod journals at a nominal size of 175 mm and main bearing journals machined to 194.5 mm (compared to the standard 195 mm) to ensure uniform fits. Hard chrome plating has been applied to journals N4 and N5 to restore dimensions and ensure surface smoothness. The component has undergone thorough inspections to guarantee proper functionality during installation. Technical Specifications Type: KURBEL Engine: J624GS-F Nsdpfoxu Ataox Af Sjlg Length: 4,418 mm Main bearing diameter: machined to 194.5 mm (standard 195 mm) Connecting rod journal diameter: 175 mm

Condition: used, Year of construction: 2020, operating hours: 555 h, functionality: fully functional, machine/vehicle number: 62006148, operating pressure: 1,000 bar, total length: 1,160 mm, high-pressure hose length: 1,000 mm, total height: 1,300 mm, total width: 800 mm, pressure: 1,000 bar, input voltage: 400 V, fuel: electricity, overall weight: 560 kg, water tank capacity: 20 l, power: 30 kW (40.79 HP), input current: 63 A, noise level: 104 dB, pressure (max.): 500 bar, input frequency: 50 Hz, Equipment: chassis, crane, Used DYNAJET 1000me 400V/50Hz/63A – 1000 Bar High-Pressure Water Jetting System – Only 555 Operating Hours This well-maintained DYNAJET 1000me high-pressure water jetting unit is available for immediate sale. With only 555 operating hours, the machine remains in excellent condition and is ready for demanding industrial cleaning and surface preparation applications. Delivering up to 1000 bar (14,500 PSI) and a flow rate of 17 l/min, the DYNAJET 1000me is designed for professional users who require maximum pressure performance combined with reliable day-to-day operation. The robust four-wheel trolley design ensures easy transportation and flexibility on site, while the industrial-grade construction provides outstanding durability even in harsh working environments. The machine is equipped with a powerful 30 kW electric motor, industrial crankshaft pump, stainless-steel water filtration system, operating-hours meter, automatic motor protection, and DYNAJET's innovative dry-stop pistol technology for improved operator safety and ease of use. Included with the machine: *1 x 1000 bar high-pressure gun *Nozzle holder *Rotating nozzle *High-pressure nozzle *10 m high-pressure hose *Original DYNAJET machine *Only 555 operating hours The DYNAJET 1000me is particularly suitable for: Industrial cleaning Surface preparation Coating and paint removal Concrete renovation work Ship and offshore maintenance Tank and container cleaning Heavy-duty maintenance applications Technical specifications: *Working pressure: 1000 bar (14,500 PSI) *Flow rate: 17 l/min *Electric motor: 30 kW *Voltage: 400V / 50Hz / 63A *Pump type: Triplex plunger pump *Water tank: 20 L *Motor protection: IP54 *Dimensions (L × W × H): 116 × 80 × 130 cm *Weight: approx. 560 kg *Operating hours: 351 h *Key features and advantages: *Only 351 operating hours *1000 bar ultra-high pressure performance *Robust industrial trolley construction *High reliability and long service life *Electric drive with low operating costs *Included 1000 bar gun, nozzle holder, nozzle, and 10 m hose *Immediate availability Nljdpfsz Dgt Tox Af Sog *Fully functional and ready for operation Please contact us for additional information, photos, pricing, or inspection arrangements.

Condition: used, Year of construction: 2005, 1 used, very well-maintained crankshaft milling attachment for mounting, e.g., on a lathe for milling crankshafts or other milling operations. Manufacturer: SEMA, Origin: Austria Model: SE 100 Year of Manufacture: 2005 Technical Data: Spindle mounting: ISO 50, Runout / Test mandrel L=300 mm = 0.01 mm Speed range, continuously variable: Currently set to 2,000 rpm Spindle is designed for: Up to 3,000 rpm Drive power: Currently 15 kW The milling spindle is designed for: Up to 25 kW Bearing diameter: 110 mm The 2 bolted adapter plates under the milling spindle are each bolted on. These plates can be used for your lathe, modified, or may need to be newly manufactured. Mounting surface of the milling spindle: L x W: 490 x 250 mm Accessories / Special Features: Milling spindle: • The milling spindle is mounted on the flat support of your lathe • Continuously variable speed adjustment, frequency inverter manufacturer LENZE, designed for up to 30 kW • Right / Left rotation • Lifetime-lubricated spindle bearings • Stable construction with hardened and ground spindle • High precision • 2-fold supported spindle with 5 spindle bearings • Workpiece clamping via a threaded spindle • Mobile carriage with control panel Nljdpfxeddziyj Af Seg • Emergency stop • Lockable main switch Indexing gear for the main spindle: • A long drive rod is mounted in the spindle bore and connected to the gear • Continuously variable speed adjustment, frequency inverter manufacturer LENZE • Right / Left rotation • Jog operation, fast / slow The pictures show this unit mounted on a universal lathe SARO SPA 10 x 3000 for milling crankshafts. This lathe is not included in the scope of supply! Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 D - 44143 Dortmund - Wambel

Condition: used, Year of construction: 1970, diameter / mm Cutting (quantity) / weight / kg This tailstock comes from the Froriep D1.050x10.000 crankshaft lathe. Nsdpfx Afotnmmbj Selg This is sold individually and can be used for various purposes Can be used, for example as a counter spindle or for other purposes. Center height: 500 mm

Condition: good (used), Zippel crankshaft cleaning system Zippel Crankshaft cleaning machine L x W x H = 3520 x 520 x 700 mm Further cleaning machines in other sizes - new and used - you will find in our store! Njdsihfn Ijpfx Af Selg International shipping costs on request!

Condition: used, type S2-900 / 190 DKGM In our opinion, the machine is in good used condition and can be inspected under power by appointment. There are 2 machines available. Nledpfjx Ik Tksx Af Ssg Accessories, tools, and clamping devices shown are only included in the scope of delivery if noted in the additional information. Subject to changes and errors in the technical data and information, as well as subject to prior sale!

Condition: ready for operation (used), Year of construction: 2013, operating hours: 2,780 h, functionality: fully functional, workpiece weight (max.): 150 kg, grinding wheel diameter: 660 mm, center height: 270 mm, center width: 1,700 mm, grinding diameter: 300 mm, spindle speed (max.): 1,000 rpm, No minimum price – guaranteed sale to the highest bidder! TECHNICAL DETAILS Workpiece Grinding diameter in rotary grinding, max.: 220 mm Grinding diameter in cylinder grinding, max.: 300 mm Rotary diameter over table, max.: 300 mm Passage in the steady rest, min. / max.: 20 / 90 mm Workpiece weight between centers, max.: 150 kg Nledpfxszarx Do Af Ssg Center height above table: 270 mm Distance between centers: 1,700 mm Grinding length with fixed tailstock: 1,500 mm Grinding length with special equipment: 1,300 mm Diameter of the chuck: 180 mm Tailstock quill travel: 50 mm Grinding wheel Grinding wheel diameter, max.: 660 mm Grinding wheel width, min. / max.: 20 / 80 mm Peripheral speed, max.: 35 / 63 m/s Grinding wheel for concave cam profiles Diameter with electro spindle, min.: 100 mm Grinding wheel width, min. / max.: 20 / 50 mm Peripheral speed, max.: 35 / 50 m/s Grinding spindle head X-axis Travel: 490 mm Measuring resolution: 0.0001 mm Workpiece head C-axis Speed range of workpiece spindle: 1 - 1,000 rpm Speed range of contour grinding spindle: 1 - 400 rpm Torque on the spindle: 80 Nm Resolution: 0.0001 ° Table Z-axis Measuring resolution: 0.0001 mm MACHINE DETAILS Drive power of the motors Grinding spindle motor: 7.5 / 15 kW Workpiece motor, C-axis: 12 W Dimensions & Weight Dimensions (L x W x H): 5,500 x 2,600 x 2,000 mm Total weight: 9,850 kg EQUIPMENT Automatic balancing device, programmable Grinding spindle head X-axis with linear motor Optical scale on the X-axis Workpiece head C-axis with encoder Table Z-axis with linear motor Optical scale on the Z-axis Workpiece motor, direct drive type, C-axis Grinding spindle motor, direct drive type Fixed tailstock Tailstock quill Note: The machine can be powered up for inspection for an additional cost of approximately €12,000.

Condition: used, mileage: 280,000 km, power: 115 kW (156.36 HP), first registration: 08/2019, fuel type: diesel, overall weight: 3,500 kg, next inspection (TÜV): 09/2027, color: white, gearing type: automatic, emission class: euro6, number of seats: 3, total length: 5,963 mm, total width: 2,010 mm, total height: 2,660 mm, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, In accordance with our "General Terms and Conditions," without any guarantee or warranty, we can offer you the following vehicle on a non-binding basis until the conclusion of the sale, subject to errors, typos, and prior sale: Nlsdpfjz Ew Iwjx Af Sog Iveco 35S16 SV Box Van (Vehicle 11) Registration Date: 15.08.2019 280,000 km Engine: 2,287 ccm 115 kW / 160 hp Euro 6 Permissible Gross Vehicle Weight (GVW): 3,500 kg MOT valid until: 09/2027 Unladen weight: 2,397 kg Payload: 1,103 kg Overall length: 5,963 mm x Overall width: 2,010 mm x Overall height: 2,660 mm Auxiliary headlights Tires: 225/55R16, approx. 60% tread remaining on the front, approx. 30/40% on the rear Trailer hitch with ball coupling Double doors, 1/2 and 1/2, at the rear Side sliding door on the passenger side is damaged 6 pairs of lashing eyes in the cargo area Side walls lined with PVC up to a certain height Wooden floor Partition Central locking with remote control 1+2 seats 2 x electric windows, mirrors, heated mirrors Multi-function steering wheel Fully automatic transmission Air conditioning Radio/CD Rearview camera with monitor Cruise control Storage compartment above Last repairs: Service on 06.06.2025: Maintenance service, water cooler GR, new coolant hose, new exhaust turbocharger Service on 23.09.2025: Maintenance service, fuel line, A/C recharge, filter cover, turbocharger solenoid valve, stabilizer link + connecting rod rear axle, front brake calipers reconditioned and front brake pads replaced Service on 24.02.2026: Maintenance service, particle filter regenerated, all injectors new, crankshaft pulley new, valve cover new Price: €6,000.00 (net) All information is provided without any guarantee or warranty. Our "General Terms and Conditions" apply. The place of jurisdiction for both parties for disputes up to a value of €10,000 is the district court of Ludwigslust; for disputes exceeding this value, it is the regional court of Schwerin. Subject to errors, typos, and prior sale.