Used Corner Connection Press for sale (24,003)

Condition: reconditioned (used), Year of construction: 2005, operating hours: 30,408 h, functionality: fully functional, pressing force: 50 t, filling opening width: 1,100 mm, filling opening length: 1,250 mm, bale width: 1,100 mm, bale height: 720 mm, bale weight: 550 kg, overall weight: 16,000 kg, oil tank capacity: 600 l, year of last overhaul: 2024, Technical data baler: Manufacturer Presona AB Type LP 50 EH1 Year of construction 2005 Operating hours 30,408 hours, as of April Number of pressed bales 198,059 as of April Pressing force main press 50 tonnes Specific pressing force 63 N/cm² Theoretical throughput capacity 530 m³/hour Throughput capacity under operating conditions 260 m³/hour Dimensions of feed chute 1,250 x 1,100 mm Bale chamber volume 2.2 m³ Blodpfju Thhrjx Ak Eeg Bale dimensions 1,100 x 720 mm, variable length Drive power 22 kW Tying 5-fold vertical, fully automatic Throughput rates with a bulk density of 30 kg/cbm 6 up to 7 tonnes/hour Bulk weight of 50 kg/cbm 7 up to 9 tonnes/hour Bulk weight of 100 kg/cbm 11 up to 14 tonnes/hour Bale density (paper/newspapers) 400 to 550 kg/m³ Hydraulic oil tank capacity 600 litres PLC control Telemecanique TSX Micro Schneider Magelis control panel Effective transport dimensions excl. baler 8,125 x 2,300 x 3,000 mm (L x W x H) Transport weight press approx. 16 tonnes Condition of the baler: The machine was partial overhauled in our workshop and general maintenance work was carried out. After completion of the overhaul work, the press was tested during operation and is available for sale at short notice. The following overhaul work was carried out: General work: Machine cleaned, derusted, primed, partially painted Wire entry marks in the press channel feed-throughs welded shut and smoothed Hydraulic unit: Hydraulic oil tank emptied, tank cleaned, new oil filled Oil filter and air filter replaced Leaky oil sight glass on hydraulic oil tank replaced All hydraulic hoses replaced Electrics: English language installed in the programme menu Two key switches in the control panel replaced Control cabinet replaced Signal lamp on the control cabinet replaced Flaps end switch replaced Electrical system of the turbulator replaced, connected and tested Press ram: All four rollers removed from the press ram and replaced Main hydraulic cylinder dismantled, disassembled and partially overhauled, cylinder tube honed, complete seal set replaced, leak test performed All plastic wear pads on the press ram replaced Pre-press: Both bearings on the pre-press shaft replaced. Both hydraulic cylinders dismantled, disassembled and partially overhauled, both cylinder tubes honed, complete seal sets replaced, leak test performed. Scraper flap on the pre-press replaced. Binding system: Two complete needles with wire deflection rollers replaced Needles adjusted and set All wire deflection rollers in the needle heads replaced Drill fingers replaced Two drill shafts replaced All 8 wear plates on the Drillomat, under the drill fingers, replaced Scope of delivery: Only the baler will be sold. The documentation (Manual, CE-declaration, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors.

Condition: reconditioned (used), Year of construction: 2009, operating hours: 22,029 h, functionality: fully functional, pressing force: 80 t, filling opening width: 1,000 mm, filling opening length: 1,400 mm, bale width: 1,100 mm, bale height: 750 mm, bale weight: 600 kg, overall weight: 16,000 kg, power: 45 kW (61.18 HP), year of last overhaul: 2025, Technical data baler: Manufacturer Avermann Maschinenfabrik GmbH & Co. KG, Germany Type AVOS 1410-45/80 Year of construction 2009 Operation hours 22,029 hours, as of December 2025 Press power main press 80kN Specific press force 103,9 N/cm² Feed channel 1,400 x 1,000 mm Theoretic cycle time 12 sec Blsdpfox A U Ncjx Ak Eog Theoretic throughput capacity 300 m³/h Bale size 1,100 x 750 (w x h), the length is variable Drive power 45 kW Connected load 75 kW Tying system 4-fold, vertical, fully automatic Throughput capacity at a bulk weight of 30 kg/cbm approx. 6,0 t/h bulk weight of 50 kg/cbm approx. 10,5 t/h bulk weight of 100 kg/cbm approx. 17,5 t/h Bale weight with a bale length of approx. 1.2 m up to 600 kg, depends on material SPS controller Siemens S7-300 Operating panel pulsotronic Baler dimensions built up 8,610 x 2,400 x 3,835 mm (l x w x h) Transport weight baler approx. 16 t Special equipment: Wear-resistant floor made of HARDOX steel Special press ram for pressing ‘difficult’ materials and loose bulk materials with small grain sizes Control cabinet air conditioning Machine foot elevation 200 mm Remark: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Dismantling of the press ram, disassembly into individual parts, reconditioning of the mechanics, replacement of the following plastic wear plates and rails: o Plastic wear rails left/right under the press ram o Plastic wear rails left/right above the press ram o Plastic main wear plate (support plate) in the centre under the press ram • Steel guide rails on the left/right in the frame • Replacement of the entire base plate, four-piece, made of wear-resistant HARDOX steel • Wire inlet rails in the press floor newly welded and smoothed • Replacement of the counter blade, two-piece, in the frame • Adjustment of the blade gap to approx. 2.5 mm • Dismantling of the binding and twisting unit, disassembly into individual parts, loosening of the mechanics, replacement of all deep groove ball bearings and axial ball bearings on the twisting shafts, wire blades cleaned and readjusted, chains greased and tensioned • Support roller in front of the twisting shafts replaced • All hydraulic hoses replaced • Oil filter and air filter replaced • Main hydraulic cylinder checked for leaks • The hydraulic oil is only one year old, has been chemically analyzed, is still in good condition, and has therefore not been changed but can continue to be used. • General maintenance work carried out Finally, the press was subjected to a machine test in manual and automatic mode; see video for the machine function test.

Condition: ready for operation (used), functionality: fully functional, -----Konica Minolta Press C 1060 with 1.3 million prints----- Tested and ready to operate! Equipment: - fiery ic308 + faci bundle - RU 509 - PF 707 VACUUM PAPER FEEDER OPTION - DF - FS 532 Bjdowx Ey Tepfx Ak Eelg - Video of the machine in operation available upon request As an experienced reseller of used copiers, we have developed real expertise in packaging and pallet shipping, ensuring that our customers receive machines in perfect condition. We ship copiers sourced from and serviced by Konica Minolta France. If you have any questions, please don't hesitate to ask. Our company offers the widest range of Konica Minolta production copiers and arranges worldwide deliveries upon request. Feel free to contact us for further information.

Condition: good (used), Bending tool, die, upper knife, upper tool, straight tool Blsdpfjd S D Dnsx Ak Eog -Tool for: press brake -Dimensions: 20 x 70 mm -Length: 3020 mm -Weight: 22 kg

Condition: excellent (used), Year of construction: 2005, operating hours: 60,000 h, functionality: fully functional, machine/vehicle number: 31765 B, color channels: 5, paper weight (min.): 50 g/m², paper weight (max.): 400 g/m², paper width (max.): 744 mm, paper height (max.): 592 mm, counter reading (color): 25,000,000, Key Technical Features & Benefits Maximum Production Speed: Runs up to 18,000 sheets per hour, ensuring you hit even the tightest deadlines. Substrate Flexibility: Effortlessly handles different gsm materials It’s a true "all-rounder" for paper and thick cardboard. Large Transferters: Double-diameter transfer cylinders and impression cylinders ensure "mark-free" printing and a smoother sheet travel path. Quick Start-Up: Features advanced automation for plate loading and wash-ups, significantly reducing make-ready times and substrate waste. Pecom Control System: Integrated console for precise remote ink and register control, ensuring color consistency across long runs. Ergonomic Design: Low-profile construction for easier access and maintenance compared to taller competitors. Automation: PPL (Power Plate Loading) / Automatic Wash-upInking Bljdpfx Aey Ipmvek Ejg Units: 16-roller high-performance inking system All units are UV Prepared 1 UNIT UV INTERDECK PLUS END OF PRESS UV Also has an IR DRYER

Condition: new, Instead of €14,874 gross RRP, now only €9,499 net (€11,304 gross incl. 19% VAT). You save -24% compared to the RRP! TIGERMETAL WH150 – Hydraulic Workshop Press 150 Tons | Electric + Manual Pump The TIGERMETAL WH150 workshop press is a powerful industrial press designed for the most demanding applications in workshops, production, and maintenance. With a pressing force of 150 tons, the machine is ideal for heavy-duty straightening, pressing, and bending operations in professional environments. Thanks to the combination of electric drive and manual hand pump, the press allows both fast operation and highly sensitive, precise pressure control – especially for delicate workpieces. 🔧 Technical Data: Model: WH150 Manufacturer: TIGERMETAL Pressing force: 150 tons Drive: Electric motor + manual pump Motor power: approx. 4 kW Connection: 400V – 16A – 50 Hz Max. working pressure: approx. 310 bar Stroke: approx. 400 mm Working width: approx. 1200 mm Max. working height: approx. 1000 mm Weight: approx. 1080 kg Advantages: ✔ Combined operation (electric + manual) ✔ Extremely high pressing force for heavy-duty applications ✔ Precisely controllable pressure ✔ Laterally movable cylinder ✔ Height-adjustable crossbeam ✔ Heavy-duty, durable steel construction ✔ Integrated pressure gauge (manometer) ✔ Safety valve for overload protection ✔ Optionally expandable with accessories The WH150 is the ideal solution for anyone looking to combine maximum pressing power with the highest level of precision, flexibility, and industrial reliability. The laterally movable cylinder and height-adjustable working table ensure maximum flexibility and optimal adaptation to a wide variety of workpieces. The massive steel construction guarantees maximum stability, safety, and a long service life – even under intensive industrial use. Some images may show a slightly different version than the one offered here. The version shown in some pictures may include an additional automatic function. A wide range of additional workshop presses in various designs, sizes, and with optional equipment is available! Available versions: 30 tons 60 tons 100 tons 150 tons 200 tons 200 tons: on request Custom machines: on request New machine! We are also happy to manufacture a custom-built press tailored to your requirements. A demonstration machine can be tested on-site under power. Bsdpfxof Sqcks Ak Ejlg ----- Please feel free to contact us – we will be happy to advise you without obligation. ----- The stated price is net plus 19% VAT. All information without guarantee! Delivery available throughout Europe! The European Commission provides a platform for online dispute resolution (OS platform). This offer serves solely as an online presentation of our products. Contract negotiations are conducted via telecommunication (email, fax, phone, messaging platforms). You will first receive a non-binding offer including our general terms and conditions as well as information on your right of withdrawal before any purchase/contract is concluded.

Condition: new, TIGERMETAL WH100 – Hydraulic Workshop Press 100 Tons | Electric + Manual Pump Instead of €10,489 gross RRP, now only €6,699 net (€7,972 gross incl. 19% VAT). You save -24% compared to the RRP! The TIGERMETAL WH100 workshop press is a high-performance and robust industrial press designed for demanding applications in workshops, production, and maintenance. With a pressing force of 100 tons, the machine is ideal for heavy-duty straightening, pressing, and bending operations. Thanks to the combination of electric drive and manual hand pump, the press offers maximum flexibility: fast operation in automatic mode and precise fine control for sensitive applications. 🔧 Technical Data: Model: WH100 Manufacturer: TIGERMETAL Pressing force: 100 tons Drive: Electric motor + manual pump Motor power: approx. 3 kW Connection: 400V – 16A – 50 Hz Max. working pressure: approx. 320 bar Stroke: approx. 400 mm Working width: approx. 1000 mm Max. working height: approx. 1000 mm Weight: approx. 820 kg Advantages: ✔ Combined operation (electric + manual) ✔ Extremely high pressing force for heavy-duty applications ✔ Precisely controllable pressure ✔ Laterally movable cylinder for flexible positioning ✔ Height-adjustable crossbeam ✔ Heavy-duty, durable steel construction ✔ Integrated pressure gauge (manometer) ✔ Safety valve for overload protection ✔ Optionally expandable with accessories The laterally movable cylinder and the height-adjustable working table allow optimal adaptation to a wide variety of workpieces and applications. The massive steel construction ensures maximum stability and a long service life—even under intensive industrial use. The WH100 is the perfect choice for anyone looking to combine maximum pressing power with precise control and industrial reliability. A wide range of additional workshop presses in various designs, sizes, and optional equipment is available! Some images may show a slightly different version than the one offered here. The version shown in some pictures may include an additional automatic function. Available versions: Bjdpfx Ajf Sqcyjk Ejlg 30 tons 60 tons 100 tons 150 tons 200 tons 200 tons: on request Custom machines: on request New machine! We are also happy to manufacture a custom-built press tailored to your requirements. The press can be tested on-site under power. ----- We are happy to provide individual consultation and prepare a tailored offer. Simply send a non-binding inquiry! ----- The stated price is net plus 19% VAT. All information without guarantee! Delivery available throughout Europe! The European Commission provides a platform for online dispute resolution (OS platform). This offer serves solely as an online presentation of our products. Contract negotiations are conducted via telecommunication (email, fax, phone, messaging platforms). You will first receive a non-binding offer including our general terms and conditions as well as information on your right of withdrawal before any purchase/contract is concluded.

Condition: good (used), Karl Krause Large Bookbinding Press with Tapping Block The machine is fully operational and ready for operation. Manufactured by Karl Krause, Germany. The press has a tapping block that increases the pressing force. Bodpfxsy Hglyj Ak Eelg Pressure: 5 tons Plate dimensions: 550 x 490 mm

Condition: used, Total height 6500 mm Floor space 2000 x 2000 mm Outdoor installation Compact filter series Model PKFP – 1 element – 1.92 x 1.92 Shaking filter Overpressure operation Filter hose length 2500 m long – 180 mm diameter - then 105 m2 filter area 2 raw air fans – 2 pipes (diameter 300 mm) 1 x fan KT 300, 15 kW power 6361 m³/h built in 1999 1 x fan S 25 / 300, 7.5 kW power 7400 m³/h, built in 1993 1 x transport fan 6.1 kW, power 57 m³/min, built in 1996 Total approx. 14,000 m3/h volume flow Briquette press Höcker Polytechnik type BrikStar C 3 - 12. 1225 Motor 3.0 kW, briquette diameter 65 mm, output approx. 40-45 kg/h depending on the specific weight of the material. Storage location: Nattheim Bodpovviytsfx Ak Eolg

Condition: used, Year of construction: 2003, Working height: 2300 mm, Working width: 3500 mm, Motor: 1.5 kW, 3 pressure cylinders from above, 2 from the side, Pressure per cylinder: 3000 kg, Cylinder stroke: up to 200 mm, Hydraulics: 10-150 bar, Space required: 3950 x 900 x 2550 mm, Weight: 670 kg Bjdpfevvkmbox Ak Eelg Storage location: Nattheim

Condition: used, Year of construction: 1992, Dimensions: 5700 x 1300 x 2400 mm Storage location: Nattheim Bsdovvkl Depfx Ak Eolg

Condition: ready for operation (used), Year of construction: 1985, Bobst SP 102 CER - Perfect condition available immediately Year 1985 Bodewathhepfx Ak Eolg Max.Size: 1020x720 mm Min.Size: 400x350 mm Max.Speed: 8000 Sh/h Max. Cutting force: 250T Paper: min. 80 gr/qm Cardboard: max. 2000 gr/qm Centerline Feeder Non-Stop Autom. Non-Stop with Sheet inserter Side guide Quick Lock system

Condition: ready for operation (used), Fully Automatic Flatbed Die-Cutter, Non-Stop Feeder, Automatic Vacuum Plate, Double Sheet Cleaning Station, Turn Die Cutting Frame, (Batch Delivery) Non-Stop Delivery With Belt, Cutting Force 300 TON, Up to 4.500 Speed/H, Working With Corrugated Cardboard Of Thickness Max. 9mm, Min. 0,9mm, Format: Max. 1055x1575mm, Min. 400x600mm, Bedpfxowly D He Ak Eslg Standard Accessories Bobst SPO 1575 EG 1980, fully rebuilted 2015, chain changed 2024.

Condition: excellent (used), Year of construction: 1992, Arpeco Impressionist 420mm web width unwind with roll lift and pneumatic 3” mandrel splice table web guide Sherman corona treater 7 x print units 7 x double UV dryers 7 x chill rolls all UV lamps are BRAND NEW ! 1 x 9.5kW chiller IR dryer Hot Air end of press double size chill roll 2 x rewind mandrels pneumatic 3” Bodpfsrrvzrex Ak Eolg many print cylinders and anilox rollers

Condition: excellent (used), Year of construction: 2004, Gallus EMS 410, 2004 Unwind unit E L electronic web guide Arcotec Corona Treatment unit 7 servo-driven flexo print stations 7 IST UV dryers 7 servo-driven water-cooled chill rolls rail system delam/relam rotary die station with K&B Gapmaster Matrix rewind Magnetic die crane und hoist BST video control Sensotec automatic register control Exit die with nip Blodpfov E Rizex Ak Eeg Rewind touch screen control panel 21 anilox rollers 9 magnetic cylinders 84 print sleeves Tooling: 12x7 Printing cylinders: 89; 96; 102; 104; 106; 108; 116; 117; 121; 168; 9x Magnetic Cylinders: 89; 96; 102; 104; 108; 112; 116; 117; 120. 1x rubber roller for varnishing. 21x Anilox rollers Good working condition In production, can be inspected at any time

Condition: ready for operation (used), Year of construction: 1984, Heidelberg SM 102 Z Straight machine Powder sprayer Year: 1984 Max format: 72 x 102 cm Conventional dampening Bjdpfxoxqv Ayj Ak Eslg Under Power Available immediately

Condition: ready for operation (used), Year of construction: 1999, operating hours: 45 h, Man-Roland 204 E OB age 1999 Only 45 Mio RCI 2 - remote controlled inking Rolandmatic continuous dampening Easy plate Blanket washing device - automatic Stream feeder, Powder sprayer Bljdewarb Hepfx Ak Eog Antistatic feeder Technical Data: Maximum sheet size: 52 x 74 cm (20.5 x 29.1 inches) Minimum sheet size: 26 x 40 cm (10.2 x 15.7 inches) Maximum printing area: 51 x 72 cm (20.1 x 28.3 inches) Maximum printing speed: Up to 13,000 sheets per hour Plate size: 605 x 745 mm (23.8 x 29.3 inches) Substrate compatibility: Paper, cardboard, light packaging materials Number of colors: Available in two-color configuration Power requirements: 400V, 50Hz, 42 kW Machine weight: Approximately 13,000 kg (28,660 lbs)

Condition: new, TIGERMETAL WH60 – Hydraulic Workshop Press 60 Tons | Electric + Manual Pump Instead of €9,237 gross RRP, now only €5,899 net (€7,020 gross incl. 19% VAT). You save -24% compared to the RRP! The TIGERMETAL WH60 workshop press is a powerful and robust solution for demanding pressing operations in workshops and industrial environments. With a pressing force of 60 tons, the machine is ideal for straightening, pressing, and bending a wide variety of workpieces. Thanks to the combination of electric drive and manual hand pump, the press offers maximum flexibility: fast operation in automatic mode and precise fine adjustment for sensitive applications. The solid steel construction and the laterally adjustable cylinder allow versatile applications while ensuring high stability and safety. 🔧 Technical Data: Model: WH60 Manufacturer: TIGERMETAL Pressing force: 60 tons Drive: Electric motor + manual pump Motor power: approx. 2.2 kW Connection: 400V – 16A – 50 Hz Max. working pressure: approx. 265 bar Stroke: approx. 400 mm Working width: approx. 1000 mm Max. working height: approx. 1000 mm Weight: approx. 670 kg Advantages: ✔ Combined operation (electric + manual) ✔ High pressing force for industrial applications ✔ Precisely controllable pressure ✔ Laterally movable cylinder ✔ Durable, heavy-duty steel construction ✔ Integrated pressure gauge (manometer) ✔ Safety valve for overload protection ✔ Expandable with accessories (e.g. prisms, support plates) A wide range of additional workshop presses in various designs, sizes, and optional equipment is available! Some images may show a slightly different version than the one offered here. The version shown in some pictures may include an additional automatic function. Bjdof Sqcrjpfx Ak Eelg Available versions: 30 tons 60 tons 100 tons 150 tons 200 tons 200 tons: on request Custom machines: on request New machine! We are also happy to manufacture a custom-built press tailored to your requirements. The pressure cylinder is mounted on a sliding carriage, allowing it to be moved sideways. This ensures optimal use of the maximum frame opening width. A demonstration machine can be tested on-site under power. ----- Please feel free to contact us – we will be happy to advise you without obligation. ----- The stated price is net plus 19% VAT. All information without guarantee! Worldwide delivery available! The European Commission provides a platform for online dispute resolution (OS platform). This offer serves solely as an online presentation of our products. Contract negotiations are conducted via telecommunication (email, fax, phone, messaging platforms). You will first receive a non-binding offer including our general terms and conditions as well as information on your right of withdrawal before any purchase/contract is concluded.

Condition: like new (used), Year of construction: 2021, Pellet production Line for sale ! Manufacturer - GENERAL DIES Capacity - 2,5-3,0 T/h Blsdjy Hfy Nepfx Ak Esg Year - 2021 , with Press General Dies never used 2026

Condition: excellent (used), Year of construction: 1995, functionality: fully functional, STC-Ref:G-182-3197 STAGO-PB-2015 ,Year: 1995 equipped with: - paper drilling machine 2 spindles Bjdpfx Aey It E Ask Ejlg - model: Stago PB-2015 - Drill spindle spacing: 60–120 mm

Year of construction: 2022, condition: new, immediately available CNC press brake YAWEI PBH160/3100-4C - Pressing force: 1600KN - max. bending length: 3100mm - Year of construction 2022 - CNC controlled hydraulic crowning - Cybelec Modeva 19T controller - WILA upper tool clamp - 60mm table with 13.5mm x 22mm slot for insert dies - 2 front support arms sliding on linear guide - CE Fiessler Akas IIF light barrier Bljdpfxjiwfp Te Ak Ejg - 24 months warranty - Commissioning, training

Condition: new, Year of construction: 2023, Immediately available, highly upgraded CNC press brake YAWEI PBH220/4100-7C - Pressing force: 2200KN - max. bending length: 4100mm - Year of construction 2023 - CNC controlled hydraulic crowning - Cybelec VISITOUCH 19T control - 7 CNC controlled axes - Y1/Y2, X, R, Z1 + Z2, X1 (Delta X) - Mechanical quick clamping upper tools type Amada - 60mm table with 13.5mm x 22mm groove for insertion dies - 2 front support arms can be moved on linear guides Bljdpfx Aeqgcq Hsk Ejg - CE with Fiessler AKAS IIF (automatic height adjustment) - 24 month guarantee - Commissioning, training

Condition: new, Year of construction: 2024, functionality: fully functional, working width: 3,100 mm, distance between stands: 2,600 mm, warranty duration: 24 months, control type: CNC control, degree of automation: automatic, number of support arms: 2, type of crowning: CNC-controlled, Equipment: CE marking, documentation/manual, emergency stop, european tool clamping system, finger protection, foot remote control, safety light barrier, Immediately available, highly upgraded CNC press brake YAWEI PBH160/3100-4C - Pressing force: 1600KN - max. bending length: 3100mm - Year of construction 2024 - CNC controlled hydraulic crowning - DELEM DA66S - 4 CNC controlled axes - Y1/Y2, X, R - Mechanical quick clamping upper tools type Amada - 60mm table with 13.5mm x 22mm groove for insertion dies - 2 front support arms can be moved on linear guides - CE with Fiessler AKAS IIF (automatic height adjustment) Bedpfx Asyvzhnjk Eelg - 24 month guarantee - Commissioning, training

Condition: good (used), Year of construction: 2012, functionality: fully functional, power: 18.5 kW (25.15 HP), input voltage: 400 V, input current: 37 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 265 mm, operating speed: 10 mm/s, reverse speed: 100 mm/s, table width: 104 mm, table length: 3,700 mm, table height: 900 mm, throat depth: 410 mm, clearance between the columns: 3,100 mm, oil tank capacity: 250 l, total length: 5,300 mm, total width: 2,700 mm, total height: 2,750 mm, overall weight: 13,100 kg, Equipment: CE marking, safety light barrier, 2012 Durma AD-R 37175 CNC Press Brake – 175 Ton x 3700mm | CNC Advantage Control | Tooling Included Used 2012 Durma AD-R 37175 CNC press brake for sale. 175 ton, 3700mm, CNC Advantage control, tooling included. Manufacturer: Durma Model: AD-R 37175 CNC Pressbrake Control: Durma CNC Advantage Control Year: 2012 Capacity: 3.7m x 175T Condition: Good Description 2012 Durma AD-R 37175 CNC Press Brake – a high-performance, precision hydraulic press brake designed for efficient and accurate sheet metal bending. This machine offers excellent value for workshops looking for a reliable 175 Ton CNC press brake with strong capabilities and proven Durma build quality. Manufactured by Durmazlar (Durma), a globally recognised leader in sheet metal machinery, the AD-R series is known for robust construction, ease of use, and excellent performance-to-price ratio. 🔧 Key Features 175 Ton Bending Capacity 3700mm Bending Length Durma CNC Advantage Control (2D Graphic Programming) 3 Axis Machine (Y1, Y2, X – Powered) Manual R-Axis via Backgauge Fingers Motorised Backgauge with Linear Guides & Ball Screw System European Style Clamping System Full Set of Top & Bottom Tooling Included Top Tool Hangers Included (Supplied, not shown in photos ⚙️ Technical Specifications Bending Force: 175 Ton Bending Length: 3700 mm Distance Between Columns: 3100 mm Stroke: 265 mm Daylight: 530 mm Throat Depth: 410 mm Table Width: 104 mm Table Height: 900 mm Speeds Y Rapid Feed: 120 mm/sec Working Speed: 10 mm/sec Return Speed: 100 mm/sec Bledey Ir D Dopfx Ak Ejg Backgauge X Axis Travel: 650 mm X Axis Speed: 500 mm/sec Backgauge Fingers: 2 (height adjustable) General Motor Power: 18.5 kW Oil Tank Capacity: 250 Litres Dimensions (L x W x H): 5300 x 2700 x 2750 mm Weight: 13,100 kg 💡 Machine Overview The Durma AD-R series is engineered for precision bending, low maintenance costs, and long-term reliability, making it an ideal solution for fabrication shops and industrial production environments. With a large daylight opening, generous stroke, and rigid frame construction, this machine is well suited for handling a wide range of sheet metal applications, from light fabrication to heavy-duty bending work. The CNC Advantage Control system provides: 2D graphical programming Automatic bend sequencing Easy part calculation USB program storage and backup User-friendly interface for fast setup and operation 🏭 Why Buy This Machine? Excellent price-to-performance CNC press brake Strong European build quality Ideal for steel fabrication, sheet metal workshops, engineering firms Complete with tooling – ready to go to work Reliable and simple CNC control – easy for operators 📦 Included with Machine Full Top & Bottom Tooling Set Top Tool Hangers (supplied) Sliding Support Arms Backgauge System Notes: *Specifications are given in good faith but not guaranteed*

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei Bledpfx Aowiqq Sjk Eog 70300 € 1328.67 € 100 to 4.5 mm 700 mm 1000 mm 210 mm 1 - 132 mm 58 1/min 6 90 mm 60 mm 300 mm 445 mm 7.5 kW 1650 mm 1545 mm 3011 mm 7000 kg Welded steel construction body frame Crankshaft made of AISI 4140 (42CrMo4) alloy steel, CNC grinded for max. precision SnBz-12 quality bronze to bearings, grinded for min surface resistance Ram supported from 6 sides Pneumatic counter-balancing of the ram 7" touchscreen Gears in oil bath Pneumatic clutch-brake combination PLC control for safety Photocell light barriers Motorized slide adjustable Mechanical overload fuse Two hand and foot pedal control Adjustable stroke (inverter) automatic centrallubrication Machine and equipment in conformity with CE-regulations OPTIONS: vibration pads € 192,00 bolster plate € 2.580,00