Used Broach for sale (209)

Condition: good (used), overall weight: 10,364 kg, Year of construction: 2019, 2019 GENERAL BROACH 10-30 GBTU VERTICAL TABLE UP BROACH Equipped with: Retriever Shuttle Table Chip Conveyor Auto Load Grayco Lube AB Panelview Coolant Tank & Pump Specifications: Capacity: 10 Ton Stroke: 30" Table Up 1″ Puller / Retriever Hydraulic Power Unit Chip Conveyor Machine Dimensions (approx.): 165″ x 48″ x 60″ Machine Weight Total (approx.): 22,800 lbs. Machine Column (approx.) : 13,000 lbs. Ibedpfx Aortrzaehyoc Base w/ Chip Conveyor (approx.): 4,700 lbs. Electrical Panel (approx.): 600 lbs. Hydraulic Power Unit (approx.): 4,500 lbs.

Condition: ready for operation (used), functionality: fully functional, "Urpe M-300 G mortising machine with an inclinable head, featuring a 0-300mm stroke, with a stroke rate of 30-35-40 strokes per minute. The distance from the tool to the column is 500mm, and the adjustable distance from the table to the ram is 425-585mm. The maximum distance between the tool and the body is 450mm. The table surface is 800x325mm, with a longitudinal travel of 550mm and a transverse travel of 265mm. The motor has a power of 5.5 hp, and the estimated weight is 1850 kg. It includes a manual indexing head and is in good condition." Ibjdpez Tc Iasfx Ahyec

Condition: good (used), functionality: fully functional, Year of construction: 1970, overall weight: 2,500 kg, broaching length: 300 mm, total length: 2,000 mm, total width: 2,000 mm, GSP M743 mortising machine Travel: 0 to 300 Stroke: 3 to 52 Ijdpfx Asz Ingvjhyebc Weight: 2.5 tons Rapid traverses on both axes Rapid traverse on table rotation, diameter 700 In very good condition

Condition: used, Year of construction: 1987, Rated current: 14A, rated power: 5.4kW, weight: 920kg, with documentation. An on-site inspection is possible. Ibsdpez S Iv Hefx Ahyjc

Condition: ready for operation (used), functionality: fully functional, Year of construction: 1972, operating hours: 24 h, machine/vehicle number: 2025, overall weight: 5,200 kg, power: 10 kW (13.60 HP), input voltage: 380 V, input frequency: 50 Hz, broaching length: 320 mm, workpiece diameter (max.): 630 mm, total length: 2,650 mm, total width: 1,810 mm, total height: 2,890 mm, Slotting Machine STANKO 7M430 The STANKO model 7M430 is a heavy-duty vertical slotting machine, designed for machining internal keyways, slots, internal splines, and profiled surfaces in large and heavy workpieces. Manufactured in 1972, this machine is intended for industrial applications requiring robust construction, high rigidity, and reliable operation. The machine is equipped with a rotary worktable with a diameter of 630 mm, allowing flexible positioning of workpieces. The maximum stroke length of the ram is 320 mm (minimum stroke 120 mm), providing a wide working range for various slotting operations. The slotting head can be swivelled ±10°, enabling angular machining and increased versatility. Feeds along the X- and Y-axes are adjustable in the range of 0.2 to 2.4 mm per double stroke, while the rotary feed of the table can be set from 0.1 to 1.4°, ensuring precise control of cutting parameters. The maximum permissible table load is 3000 kg, making the machine suitable for large and heavy components. The distance from the table surface to the chisel guides is 500 mm, and the machine offers generous table travels: 650 mm longitudinal, 500 mm transverse, with 360° table rotation. The drive motor has a power rating of 10 kW, providing sufficient cutting force for demanding machining tasks. With overall dimensions of approximately 2650 × 1810 × 2890 mm and a total weight of about 5200 kg, the STANKO 7M430 features a rigid cast-iron construction that ensures excellent vibration damping and long-term stability. Condition: *Used machine *Ready for operation *Fully functional *Operating hours: approx. 24 h Scope of delivery: *Complete set of change gears *Technical passport (Russian) *Operating manual (Russian) Typical applications: *Slotting of internal keyways *Machining of internal splines *Profile machining of internal surfaces *Machining of large and heavy components Iedpfxjx U Tr Ae Ahyjbc *General mechanical engineering and repair work

Condition: refurbished (used), functionality: fully functional, Year of construction: 1988, machine/vehicle number: 3615/673, input voltage: 400 V, input frequency: 50 Hz, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, reverse speed: 3 mm/s, total length: 750 mm, total width: 800 mm, total height: 2,250 mm, -WR 177- Manufacturer: Rausch Model: RS3 /1000 Machine No.: 3615/673 Year of Manufacture: 1988 Weight: 350kg Overhaul: 04/2025 by Wiemers AG General / Technical Data: Unused, partially overhauled, mechanical vertical broaching machine Rausch RS 3 without CE marking Pulling force: 3,000kg Broaching speeds: 3m/min Return speed: 3m/min Maximum stroke: 1000mm Maximum tool length: 1200mm Ibsdpfx Ajz Hl U Iohyjc Table size / work area: 430mm x 320mm / 340mm x 220mm Table through-hole: Ø 90mm for standard broaching mandrels "System Rausch" Workpiece diameter: any (with the cabin removed) Broaching capacity / keyway width: up to 18mm in steel (from 16mm keyway width only with offset tool shank) Dimensions (h x w x d): 2,250mm x 800mm x 750mm (h = including 3-sided protective cabin) Motor: 3.0kw / Power supply: 400V / 50 Hz Equipment: - Protective door with safety monitoring (emergency stop circuit) - Chip chute - Externally adjustable tool length adjustment system (System Rausch) - Protective cover for stroke adjustment and electrical switching units - Electrical sensing of the clamping jaws (System Rausch) (Tool removal control to prevent unintentional retraction of the drawbar, providing additional safety for the operator & tool) - Integrated coolant system - 4-sided enclosed splash guard hood with protective door - Extra reinforced chip basket and chip sieve with magnet insert - Control panel external - 2 grease points for the trapezoidal spindle drive with manual grease gun directly on the spindle nut Note: The machine has been partially overhauled by Rausch. The following wear parts have been replaced and renewed. - New trapezoidal spindles and spindle nuts made of cast, wear-resistant bronze - All bearings and seals are new - New electrical system - 4-sided enclosed splash guard hood with protective door at the front - New protective door instead of the light barrier in the machine room - New clamping jaws - All sheet metal parts, such as covers, chip chute, basket, sieve and spindle protection, are new. - External control panel General The double spindle drive ensures a smooth and central pulling point as well as a constant broaching speed. The machine is primarily designed for the production of keyways up to 18mm. (from 16mm keyway tools only with offset tool shanks) Due to its design, the machine can be quickly and easily set up for broaching with flat broaching tools for keyways. Due to the structurally universal design of the drawbar and the machine table, broaching with profile and flat broaching tools is possible without the use of additional draw heads.

Condition: ready for operation (used), functionality: fully functional, Cable pulling machine / RAUSCH RS 6 /1300 with pulling extension & accessories Ibedpfx Aoz I Dbvjhyjc -Ram stroke / stroke length - Standard 1300 mm (+ pulling extension) -Pulling force 6000 kg -Various cable pulling tools -Various accessories -Workbench Dimensions (disassembled) L x W x H 1.6 x 1.7 x 2.3 meters / Weight 3500 kg Errors and omissions excepted.

Condition: used, functionality: fully functional, Year of construction: 2019, machine/vehicle number: 53, overall weight: 38,500 kg, input voltage: 400 V, input current: 355 A, input frequency: 50 Hz, broaching speed: 12 m/min, workpiece diameter (max.): 225 mm, total length: 7,100 mm, total width: 11,560 mm, total height: 6,000 mm, Forst RISH 60 x 2125 x 630 – Vertical internal broaching machine Used Forst broaching machine for internal broaching of ring gear workpieces. The machine features a lifting table and a servo-electric broaching drive; the broach pitch is set via the NC program. Machining is performed individually or in pairs, depending on the workpiece. Identification Manufacturer: Forst Technologie GmbH & Co. KG Type: RISH 60 x 2125 x 630 Factory number: 53 Ibsdpfx Ahez Hq Akjysc Forst order number: M233202 Reference / Inventory number: 351024 Year of manufacture: 2019 (according to machine data sheet) Technical data according to machine documentation - Maximum tensile force: 600 kN - Maximum stroke: 2,125 mm - Maximum cutting speed: 12 m/min - Return stroke speed: 20 m/min - Maximum workpiece diameter: 225 mm - Maximum workpiece height: 50 mm - Maximum tool diameter: 200 mm - Tool shank diameter: 80 mm - Tool tip diameter: 75 mm - Overall dimensions (L x W x H): approx. 7,100 x 11,560 x 6,000 mm - Total weight of the machine: approx. 38,500 kg - Weight of the base machine: approx. 34,500 kg - Electrical connection: 400 V, 3 phases, 50 Hz - Rated current according to nameplate: 355 A Documented features - Siemens SINUMERIK 840D sl / S7-300 - Operator panel OP012 and hand-held operating unit HT8 - SKF roller screw drive and linear guides - Hydraulic workpiece clamping - Coolant system with high/low pressure supply and 1,800-liter tank - Chip conveyor and chip centrifuge - Oil mist separator and central lubrication system Operating manual and technical documentation are available. The data and features listed describe the documented machine condition. The actual scope of supply should be agreed upon before finalization. The suitability for other workpieces requires a technical assessment and, if necessary, adapted tools and fixtures. Used machine, operated without malfunctions until disassembly. Price on request.

Condition: ready for operation (used), functionality: fully functional, overall weight: 2,200 kg, total length: 2,500 mm, total width: 500 mm, total height: 1,200 mm, Spline broaching machine (internal broaching machine) VEB Maschinenfabrik "John Schehr", Meuselwitz, year of manufacture approx. 1955, with extensive accessories Condition: functional Year of manufacture: approx. 1955 Location: West Saxony Price: €3,000 (negotiable) Technical data: Ibodpfxozyl E Ne Ahyec Manufacturer: VEB Maschinenfabrik "John Schehr", Meuselwitz, Leipzig district Manufacturing number: 6171 Total weight: approx. 2.2 t Broaching length: approx. 1,000 mm Type of current: three-phase, 50 Hz Operating voltage: 220 V Accessories: Extensive stock of broaching tools (various spline shapes/sizes) available Description: For sale is a historical spline broaching machine (horizontal internal broaching machine) from VEB Maschinenfabrik "John Schehr", Meuselwitz – a well-established, internationally recognized East German machine tool manufacturer. The machine is used to broach splines (e.g. keyways) in bores using broaching tools and has a broaching length of approximately 1,000 mm. The scope of delivery includes an extensive stock of broaching tools in various designs – a significant added value, as corresponding tools are hardly available on the market anymore. The machine is functional. Inspection and functional testing at the location in West Saxony are possible by arrangement. Price: €3,000 (negotiable) Other machines available from site liquidation Site takeover negotiable

Condition: good (used), Year of construction: 1970, pulling force - max. 2 t max. ram stroke 400 mm max. workpiece diameter 1000 mm workpiece weight 10 t Ibsdpjz Ic A Esfx Ahysc clamping table 900 x 680 mm total power requirement 5,5 kW weight of the machine ca. 1,7 t dimensions of the machine ca. 1,3 x 1,2 x 1,5 m

Condition: like new (used), functionality: fully functional, Year of construction: 2025, overall weight: 370 kg, power: 3.5 kW (4.76 HP), input voltage: 400 V, input frequency: 50 Hz, broaching length: 800 mm, broaching speed: 3 m/min, total length: 920 mm, total width: 800 mm, total height: 1,950 mm, Manufacturer: Rausch (Haan/ Rhld) Model: RS 3 G/800 Machine No.: 2968/424 Year of manufacture: 1970 Weight: 370kg Overhaul: 8/2025 by Wiemers AG Our Ref. / Machine No.: WAG 787 General / Technical Data: Ibsdpfx Ahoytvyxjyjc Unused, overhauled mechanical vertical broaching machine by Rausch Pulling force: 3,000kg (30kN) Broaching speeds: 3m/min and 6m/min Return speed: 3m/min Maximum stroke: 800mm Maximum tool length: 1,000mm Table size / working surface: 340mm x 220mm / 430mm x 310mm Table opening: Ø 90mm for standard broaching mandrels Workpiece diameter: unlimited (without spray guard cabin) Dimensions (h x w x d): 1,950mm x 820mm x 900mm (h = table height from floor without attachments) Motor: 3.5kW Power supply: 400 Volt / 50 Hz Accessories / Special Features: - Modified drive system with geared motor and toothed belt drive - 2 broaching speeds: 3m/min & 6m/min - External stroke adjustment, cross-machine reproducible tool length adjustment system - Integrated coolant unit with check valve and drain cock, including selector switch for automatic operation (does not automatically switch in swivel mode) - Patented coolant/lubricant swivel system - Three-sided enclosed, front-open spray guard cabin (no external operator panel) - Machine enclosure below the safety door with chip guard and tool storage area - Electrical cabling within steel protective conduits - Electrical jaw monitoring (tool removal control to prevent unintended retraction of the pull bridge) - Safety door with integrated emergency stop function - Control panel made from stainless steel sheet with permanent marking - 4 central lubrication points for the trapezoidal spindle drive - Machine documentation Remarks: The machine is fully overhauled, with the frame completely refurbished. The following wear parts have been replaced: - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals replaced - Central drive shaft is new - Coolant system (pump, check valve and drain cock), including coolant/lubricant swivel system, is new - Jaws are new (pull bridge additionally reinforced) - A switchable jaw monitoring system has been installed (additional safety for operators and to prevent tool breakage) - A safety door with interlock has been installed instead of the rubber reach-in protection - Tool length adjustment system relocated outside the machine compartment - Additional limit switches installed - Complete electrical system (control cabinet) with Siemens components is new - Control panel made of stainless steel with durable labeling - New geared drive motor (SEW) with toothed belt drive - Machine has been repainted with 2-component structural paint The machine is stored at our warehouse and can be inspected under power.

Condition: like new (used), functionality: fully functional, Year of construction: 2020, operating hours: 50 h, overall weight: 640 kg, input voltage: 400 V, input frequency: 50 Hz, workpiece diameter (max.): 400 mm, de machine is in nieuwstaat. neem contact op voor meer info. Ibodozugnhspfx Ahysc

Condition: good (used), Year of construction: 2004, machine/vehicle number: 3234, (Please tell us your offer price) Sale only within Europe, incl. Turkey Price without packaging; delivery condition: FCA (machine location) ===== Technical data see handout. All warranty rights are excluded. For the correctness of the technical data and year of construction, for the completeness of accessories and tool equipment, and for compliance with all safety and environmental protection requirements specified in the accident prevention regulations. No sale to private individuals. Sales only within Europe, incl. Turkey Price without packaging; Delivery condition: FCA (machine location) ===== Technical data please see handout in attachment. German text leading language. Without any guaranty and warranty, including completeness of tools & accessories as well as environmental and safety regulations. No private sales. Ibedpfx Aszluyaohyjc

Condition: used, total length: 2,000 mm, total width: 1,600 mm, total height: 2,350 mm, Colour: White Empty weight: 3.000 kg - Drive system: Conventional - Model: vertical - Number of axes [pcs]: 3 - Power [kW]: 5.5 - Max. stroke [mm]: 250 - Max. reach [mm]: 365 - Table diameter [mm]: 500 - Table length [mm]: 500 - Table width [mm]: 500 - Table depth [mm]: 500 - X-axis travel [mm]: 560 - Y-axis travel [mm]: 450 - Z-axis travel [mm]: 250 - Min. stroke speed [rpm]: 22 - Max. stroke speed [rpm]: 112 - Transport dimensions: 2000mm x 1600mm x 2350mm (l x w x h) - Transport weight [kg]: 3000kg - Transport packages [pcs.]: 1 Ibsdpfoz R Dr Ujx Ahyoc Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Lukas van Rossum

Condition: used, Year of construction: 2008, functionality: fully functional, machine/vehicle number: serie nr 3149, overall weight: 11,800 kg, total width: 6,615 mm, total length: 8,890 mm, total height: 2,050 mm, spindle diameter: 50 mm, type of input current: three-phase, space requirement length: 16,000 mm, space requirement width: 8,000 mm, milling spindle length: 650 mm, compressed air connection: 8 bar, spindle speed (min.): 3,500 rpm, spindle speed (max.): 3,500 rpm, length stop: 3,450 mm, input voltage: 125 V, power: 65 kW (88.38 HP), main saw diameter: 450 mm, corner unit for window and door frames, including tools. controlled from the office (Groeneveld). interpolation (angled pins). barcode laser. return transport. documentation available. complete sets of spare blades/saws, including router bits, linked to Groeneveld. automatic counter-piece. maximum workpiece length 6000. sticker printer for barcode. automatic waxelite pump. automatic central lubrication. connections for pin holes and counter-molds. automatic length stop and rotation for workpieces. including extraction pipes with automatic valve. thicknesses from 38 to 150 mm. pin bank: 1x saw blade 40mm. 2x pin shaft 50x650. 2x edge breaker 30x40. router: 1x rounding router 30x40. 3x router bits 50x600. machine can be picked up here; in conjunction with Bos Machines (dismantling and transport not included in the price). price excludes VAT. Ijdpfx Ahjztptqoyjbc

Condition: refurbished (used), functionality: fully functional, Year of construction: 2024, broaching length: 1,000 mm, number of broaching positions: 1, broaching speed: 3 m/min, Manufacturer: Rausch (Haan/Rhld) Model: RS 6/1000 Machine No.: 51261 Year of Manufacture: 1978 Weight: 680 kg Overhauled: 11/2024 by Wiemers AG General Information / Technical Data: Overhauled mechanical vertical broaching machine Rausch RS 6 G Pulling force: 60 kN Broaching speeds: 3 m/min and 6 m/min Return speed: 6 m/min Maximum stroke: 1000 mm Maximum tool length: 1200 mm Table dimensions / Working area: 610 x 470 mm / 520 x 320 mm Table aperture: Ø90 mm for standard broaching mandrels Workpiece diameter: unlimited Dimensions (H x W x D): 2,250 mm x 850 mm x 1,200 mm (H = table height from floor, without attachments) Motor: 4.4 kW / 5.5 kW Power supply: 400 Volt / 50 Hz Additional modifications/upgrades to the original machine performed: - External stroke adjustment - New, machine-independent, reproducible tool length adjustment system - Additional limit switches for end position monitoring - Safety door with monitoring (integrated in the emergency circuit) - Machine enclosure below safety door with chip protection and tool storage area - Electrical sensing of clamping jaws (tool removal monitoring to prevent unintended retraction of the broaching bridge) - Coolant swing system with solenoid valve operated during swing motion (for switching on coolant before broaching stroke – optical flow control ensures lubrication, no dry cutting!) - Routing of electrical cables in protective steel conduits - Heavy-duty control cabinet mounting for machine components - Additional oil-proof drip tray on the control cabinet - Three-sided closed splash guard cabin (W = 960 x D = 450 x H = 590 mm) Ibjdsw Ighijpfx Ahyjc - Reinforced chip screen with magnetic separator - Control panel made of stainless steel with durable labeling - 4 central lubrication points for trapezoidal spindle drive Remarks: The machine has been completely overhauled, the machine body fully refurbished. All wear parts have been replaced. - New trapezoidal spindles and spindle nuts made from cast wear-resistant bronze - All bearings and seals renewed - The coolant system (pump, solenoid valve, and drain tap), including the coolant/lubrication swing system, is new - The clamping jaws are new - Complete electrical system (control cabinet) is new - All sheet metal and enclosures are new - The following components have been overhauled and re-used: - Machine base - Machine column - Machine table with table insert - Broaching bridge (clamping jaws new) - Gear wheels - Electric motor (new brake, new bearings) The machine is stored in our warehouse and can be inspected under power. The attached images are original photos of the machine. The machine is CE marked. The CE marking corresponds to the status as of 1998 (first overhaul).

Condition: good (used), Year of construction: 1993, Equipped with: 9" Cutter Head Power Stocks Crowning Auto Loader Heidenhein Scales Variable Feed/Speed Cutter Head RS232 Serial Port Trabon Lube Coolant W/Magnetic Chip Separator AC Servo Motors Full Splash Guards Iedperuahwjfx Ahyobc Stack Light Manuals Specifications: Work Gear Pitch Diameter 9" & 12" Cutter Head: 1-12", 1-8" Work Gear Max. O.D. 9" & 12" Cutter Head: 12 1/2", 8 1/2" Diameter Pitch Range: 4-20 Distance Between Centers: 23" Cutter RPM 9" & 12" Cutter Head" 50-500, 50-400 Max. Table Travel Conventional, Tangential, Diagonal: 5", 2" 5"-2" Diagonal Traverse Angle Straight Shaving: 0 Deg. - 90 Deg. Traverse Angle Crown Shaving: 45 Deg. Max. Approx. Max. Table Angle Crowning: 5 Deg. Max. Table Angle Taper: 1 Deg 30' Max. Cutter Head Crossed Axes Angle Left & Right: 25 Deg. Table Cross Feed Inches Per Minute: .5-35 Table Up-Down Feed Inches Per Minute: .004-12.5 Table Up-Down Travel: 8 1/8" Approx. Weight: 9600 lbs

Condition: excellent (used), functionality: fully functional, total length: 2,285 mm, total width: 1,525 mm, total height: 2,135 mm, Butler Slotting Machine Model:8" Precision Table Area:508mm (Rotary) Throat:500mm Max Under Ram:400mm Ibsdpfxez S Nphs Ahyjc Stroke:203mm Dimensions: 2285 x 1525 x 2135mm

Condition: not inspected (used), Year of construction: 1988, Clamping plate: 595 x 445 mm Stroke length: 400 mm Stroke: 400 mm Machine weight approx.: 1,600 t Space requirement approx.: 1,400 x 1,200 x 1,500 mm Ibjdpfx Ahoznbrheyec Smallest/Largest cutting speed: 0 - 20 m/min Smallest/Largest return speed: 40 m/min Largest workpiece diameter according to DIN 6885 (boring): 230 mm

Year of construction: 1978, condition: good (used), U.S. MODEL 50TX120 VERTICAL PULL DOWN BROACH Equipped with: Retriever Puller Hydraulic System Coolant System Chiller Chip Conveyor Manuals Specifications: Normal Broaching Capacity: 100,000 Lbs at 922 PSI Peak Force Capacity: 133,600 Lbs at 1350 PSI Main Slide Stroke (Bump Inches): 106 Ibodpfx Aortrzlohysc Maximum Cutting Speed: 20 Ft/Min. Maximum Return Speed: 40 Ft/Min. Main Pump Motor: 75 HP at 900 RPM Hydraulic Reservoir: 365 Gallons Handling Pump Motor: 10 HP at 1200 RPM Coolant Pump Motor: 1.5 HP at 1800 RPM Coolant Pump Capacity: 100 Gallons / Min at 23 Head Ft. Coolant Reservoir Capacity: 600 Gallons Approx. Floor Space ( Width x Depth x Height): 65" x 96" x 243" Net Weight, Approximate: 79,000 #

Condition: refurbished (used), functionality: fully functional, Year of construction: 1987, machine/vehicle number: 60213/674, input voltage: 380 V, input current: 15 A, input frequency: 50 Hz, broaching length: 1,000 mm, number of broaching positions: 1, -WAG 893- For sale is a Rausch RS6/1000 internal demolition machine. Manufacturer: Rausch Type: RS6/1000 Year of manufacture: 10/1987 Ibjdpfx Ahszvwlyoyjc Machine no.: 60213/674 Weight: approx. 800 kg Tractive force: 60 kN Further information will be added shortly...

Condition: used, Drawing machine / stretching machine KARL KLINK RSI 2.5 EH -Pulling force 2500 kg -Stretching speed 1 mm to 9 mm/min (infinitely variable) -Stroke length 800 mm -Max. workpiece diameter approx. 250 mm -Motor power approx. 3 kW -Coolant system -Pulling force indicator Isdpfx Aezwdrvshyebc -Pulling force limitation -Various guide bushings (see pictures) -Machine feet Dimensions: L x W x H 1.1 x 0.7 x 2 meters / Weight 1600 kg Errors and omissions excepted.

Condition: good (used), Year of construction: 1980, machine/vehicle number: 20007, Offer 23326 Technical specifications: - Broaching tool width up to 10 mm - Broaching tool length up to 1000 mm Iedpfx Asyfgc Iehyjbc - Pulling force: 1.5 t - Working speed: 4 m/min - Working / operating height: 1000 mm - Drive: 400 V / 1.5 kW - Required space: approx. W 1500 x H 1000 x D 400 mm - Weight: approx. 200 kg

Condition: ready for operation (used), Year of construction: 2008, A vertical internal broaching machine Frömag is available. Broaching tools: 3, stroke: 800mm, pulling force: 60kN, connected load: 15kW. Machine dimensions X/Y/Z: approx. 1050mm/900mm/3800mm, control: Frömag Commander PP-10. An on-site inspection is possible. Iodpexph Sdofx Ahysbc

Condition: good (used), Year of construction: 2004, - Traction force: max. 160 kN - Broaching stroke: max. 1000 mm - Workpiece feeder stroke: max. 630 mm - Table width: 630 mm - Broaching speed: 10 m/min - Return speed: 23 m/min - Installed power: max. 88 kW - Machine weight: 12,410 kg Transport and loading can be organized throughout Europe at an additional cost, upon request. Prices plus VAT Iodpfx Ahezvfpgeyebc Inspection is possible by appointment. Please contact us, our team looks forward to assisting you. Machine purchase / sale PURCHASE / SALE OF PRODUCTION & METALWORKING MACHINES, MACHINE TOOLS, AND MORE. Are you looking for a high-quality, yet affordable machine for your production? Or do you wish to sell yours? For further information or contact options, reach us via the contact form.