Band saw

MEP Shark

Condition: reconditioned (used), Used semi-automatic bandsaw MEP Shark 281 sxi evo Three operating modes: semi-automatic, manual, and manual dynamic (gravity) Blade dimensions: 2950 x 27 x 0.9 mm Two blade speeds: 36/72 m/min Max vice opening: 285 mm Cutting capacity: at 0° round 250 mm, rectangle 280x200 mm at 45° round 190 mm, rectangle 180x180 mm at 60° round 120 mm, rectangle 110x110 mm Year: 2006 Weight: 435 kg Fjdpfx Asyyn Suocwjga Fully serviced.

Condition: used, Year of construction: 1997, dimensions of saw-band 3150 x 25,4 x 0,9 mm 20/40 m/min capacity 90 degrees: round 260 mm capacity 90 degrees: square 250 mm capacity 90 degrees: flat 320 x 200 mm Fedjyyc A Iopfx Acwoga capacity 45 degrees: round 230 mm capacity 45 degrees: square 210 mm capacity 45 degrees: flat 240 x 200 mm

Condition: good (used), cutting height (max.): 330 mm, cutting range round steel at 45°: 250 mm, cutting range round steel at 90°: 280 mm, Saw capacity: 280 mm round 330 mm square Saw capacity 45º: 250 mm round 250 mm square Fodpfx Ajtt Nd Rjcwsga Saw speed: 40/80 mtr.min. Sawbelt: 3.320 x 27 x 0,9 mm Saw angle: 0 - 60º Featured with: - Coolingunit Country of origin: Italy Motor power: 1,8 kW Machine weight: 700 kg Machine LxWxH: 190 x 120 x 135 cm

Condition: like new (used), Year of construction: 2017, Used automatic bandsaw MEP Shark 332 nc 5.0 Blade dimensions: 3320x27x0.9 mm Cutting angle range: -45° to +60° Blade speed: 15 - 100 m/min Cutting capacity at 0°: - round 300 mm - square 260 mm - rectangular 330x260 mm Four operating modes: manual, semi-automatic dynamic, semi-automatic, and automatic Year of manufacture: 2017 Machine weight: 1150 kg Additional equipment: Fjdpsxz Ulbefx Acwega - special vise to reduce remnants - KIT IoT Industry 4.0 Ready The machine is like new. It has only 515 operating hours.

Condition: new, Length: 1500 mm 6 rollers made of tubular steel, width: 185 mm Diameter: 20mm Height continuously adjustable: 650 - 1030 mm Fgsdpsfxu Tkofx Acwoa Space requirement: 1500 x 250 x 650/1030 mm

Condition: new, cutting diameter 250 mm saw band length 2950x27x0,9 mm band speed 36/72 m/min total power requirement 1,8 kW weight of the machine ca. 440 kg Basic equipment: Vice with quick adjustment and adjustable guide bars Hydraulic band tensioning device with tensioning pressure display Base frame with removable coolant tray Chip clearing brush Precision stops set for cuts of: 0°, 45° and 60° left and 45° right Turntable for double miter cuts Fgedpfxjfg E H No Acwsa Electric coolant device 48 V (A micro spray device can be installed)

Condition: new, dimensions of saw-band 3650 x 27 x 0,9 mm speed 15 - 100 m/min vice 335 mm capacity 90 degrees: round 300 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 330 x 260 mm capacity 45 degrees: round 260 / 200 mm capacity 45 degrees: square 250 / 180 mm capacity 45 degrees: flat 270 x 200 / 200 x 160 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm capacity 60 degrees: flat 170 x 170 mm total power requirement 2,2 kW weight 1.105 kg dimensions 2700 x 2300 x 1800 mm Fully automatic electro-hydraulic band saw with multi-micro processors and additionally semi-automatic, semi-automatic-dynamic and manual Function. - Automatic cycle (cuts from 0 ° to 60 ° link). CNC machine with two Fgedpfxjyv Nylo Acwsa controlled axes that allow for the same material thickness 1000 various editing programs, each with a different cutting length and quantity, too program. - Semi-automatic, semi-automatic-dynamic and manual cycle (cuts from 45 ° right to 60 ° left) - Semiautomatic dynamic system (manual lowering of the saw band bow up to the desired position and cycle start via the push button.) - Manual or semi-automatic-dynamic cycle to cut directly without Programming. Some features: - New fieldbus communication system (Modbus protocol) - Display with 20 characters x 4 lines to display the technical parameters such as: - Saw blade speed - Number of programmed and executed cuts - saw blade thickness - feed length - cutting time - ammeter - belt tension - Display of (about 100) diagnostic messages and warnings, everything in the respective user language. - Display and entry of the alarm and error messages with the possibility of display incidents that have occurred. - automatic parameter setting via control, if a new driver or Inverter is mounted. - Electronic inverter for continuous regulation of the belt speed of 15 up to 100 m / min. - New hydraulic control unit of the latest generation, highly efficient and with low energy consumption. - New material supply of 600 mm with stepper motor and ball screw mounted on opposite ball bearings. - Hublauf the saw blade directly from the control panel programmable, for Adaptation to the cutting material. - Electronic band tension control. - Automatic monitoring of the cutting load by a direct on the Cylinder mounted servo valve. - The coolant sump (equipped with 2 electric pumps for lubrication and Cooling of the saw blade) is installed in the base. - Swarf drawer (can be replaced by a chip conveyor - see Optional) - Preparation for the installation of the minimum lubrication set of the saw blade (Optional), in addition to conventional standard lubrication with emulsion oil. Chip removal brush. - Machine is intended for lifting truck transport. - Bi-metal saw band for solid and profile material.

Condition: new, capacity 90 degrees: round 300 mm capacity 90 degrees: square 250 mm capacity 90 degrees: flat 380x250 mm 260 mm 250 mm Fsdoyv Ntrjpfx Acwega 300x200 mm 180 mm 170 mm 200x170 mm 240 mm 210 mm 280x160 mm dimensions of saw-band 3770x27x0,9 mm 385 mm speed 40/80 m/min total power requirement 1,5/1,8 kW weight 695 kg

Condition: new, dimensions of saw-band 2950x27x0,9 mm 2 speeds 36/72 m/min Vice opening 285 mm capacity 90 degrees: round 250 mm capacity 90 degrees: square 220 mm capacity 90 degrees: flat 280x220 mm capacity 45 degrees: round 230/200 mm capacity 45 degrees: square 200/170 mm capacity 45 degrees: flat 220x200/200x140 mm capacity 60 degrees: round 120 mm capacity 60 degrees: square 80 mm capacity 60 degrees: flat 140x100 mm output 1,5 / 1,8 kW Weight 440 kg dimensions 1700x1000x1650 mm - with semi-automatic lowering - The CUT CONTROL SYSTEM allows semi-automatic lowering of the Saw bow by the weight of the saw head - The lowering speed is infinitely regulated. Single cuts can do so be carried out with uniform feed - The SHARK 282 CCS has a turntable for double-sided miter. The cut always takes place in the same groove Fodpsyv Nptsfx Acwega

Condition: new, 36/72 m/min capacity 90 degrees: round 300 mm capacity 90 degrees: square 260 mm capacity 90 degrees: flat 330x260 mm capacity 60 degrees: round 180 mm capacity 60 degrees: square 170 mm capacity 60 degrees: flat 170x170 mm capacity 45 degrees: round 260/200 mm capacity 45 degrees: square 250/180 mm capacity 45 degrees: flat 270x200/200x160 mm dimensions of saw-band 3650x27x0,9 mm total power requirement 1,5/1,8 kW Overall size 2130x1400x1950 mm Fgjdpeyv Nmlefx Acwea Weight 670 kg Semi-automatic function: - Vice closes and engine starts - Saw head lowers for the cut - Engine shuts off - Saw head lifts, vice opens Semiautomatic dynamic system: Manual lowering of the saw blade to the desired position and cycle start over the hand switch. Upper position is saved automatically.