Band saws horizontal - manual - cutting range round 221-299mm

MEP Shark 281 CCS

Condition: new, saw band dimensions 2950x27x0,9 mm 2 speeds 36/72 m/min vice opening 285 mm cutting range at 90 degrees: round 250 mm cutting range at 90 degrees: square 230 mm Cutting range at 90 degrees: flat 280x200 mm Cutting range at 45 degrees: around 190 mm Cutting range at 45 degrees: square 180 mm Cutting range at 45 degrees: flat 180x180 mm Cutting range at 60 degrees: around 120 mm Cutting range at 60 degrees: square 110 mm Cutting range at 60 degrees: flat 110x110 mm Total power requirement 1,5/1,8 kW Njdpsh Dmh Hjfx Ahvowc weight 375 kg Dimensions 1700x1000x1650 mm Equipment: - with semi-automatic lowering - The CUT CONTROL SYSTEM allows semi-automatic lowering of the saw bow by the by the weight of the saw head. - The lowering speed is infinitely variable. Single cuts can thus be be carried out with uniform feed

Condition: new, Year of construction: 2024, load capacity: 300 kg, Protec KT 300 H welding turntable, 170/400 special version Horizontal load 300 kg, tilted 150 kg Power consumption 220 V, 50 Hz Table diameter 450mm Hollow shaft diameter 170mm Table height 500mm Nodpfjrypmgjx Ahvswc Welding current transmission 400 A Quick-action chuck diameter 300mm, surcharge 550.-€ Quick-action chuck diameter 400mm, surcharge 750.-€ Crank gear motor 0 - 90° stepless adjustment Infinitely variable speed 0.01 to approx. 5 rpm. incl. foot remote control Digital display with welding time limiter (if required)

Condition: new, cutting diameter 250 mm Nwodpfxoxaa H Ie Ahvoc capacity 90 degrees: flat 280 x 200 mm capacity 90 degrees: square 230 x 230 mm capacity 45 degrees: round 190 mm capacity 45 degrees: flat 180 x 180 mm capacity 45 degrees: square 180 x 180 mm capacity 60 degrees: flat 110 x 110 mm capacity 60 degrees: square 110 x 110 mm capacity 60 degrees: round 120 mm vice 285 mm turning speed range: 36 / 72 m/min saw band length 2.950 x 27 x 0,9 mm total power requirement 1,5/1,8 kW weight of the machine ca. 370 kg. dimensions of the machine ca. 1620 x 1360 mtr. Equipment: - robust electro-hydraulic band saw (INDUSTRY) - one-sided miter cut up to 60° - automatic saw bow lowering * with continuously adjustable feed * limit switch at the end of the cut - manual cutting function selectable - 2x saw band speeds - saw band guide made of hard metal plates - 1x saw band - 1x angle stop - moving chip removal brush - control panel - front right - hydraulic pressure box for saw band tension * with analogue pressure display (manometer) - machine base - operating instructions in German SPECIAL ACCESSORIES INCLUDED: - MEP LubeCut micro dosing device

Condition: new, cutting diameter 250 mm saw band length 2950 mm cutting width 280 mm dimensions of saw-band 2950 x 27 x 0,9 mm capacity 90 degrees: flat 280 x 200 mm capacity 90 degrees: square 230 mm capacity 45 degrees: round 190 mm capacity 45 degrees: flat 180 x 180 mm capacity 45 degrees: square 180 mm capacity 60 degrees: round 120 mm capacity 60 degrees: flat 110 x 110 mm capacity 60 degrees: square 110 mm total power requirement 1,5 / 1,8 kW weight of the machine ca. 0,4 t Powerful miter band saw for cuts from 0 ° to 60 ° left Nsdjxz Hhzepfx Ahvswc -CCS (CutControlSystem) for automatic cutting. (Stepless regulation of the Feed and switch-off at the end of the cut) Description: -Manual cutting cycle -AUTOMATIC CUT: (via selector switch) with stepless settings of the Lowering speed and adjustment of the cutting pressure via compensating spring -Stable, torsion-resistant and low-vibration saw frame made of cast steel -Vice with quick release - Carbide band guides for maximum cutting precision -Large dimensioned deflection discs, adjustable made of cast steel -Hydraulic unit for the saw band tension and monitoring with display on Manometer (belt tension = 900 kg) -Clearly arranged control panel with all controls -Electric coolant pump for cooling and lubricating the saw band -Schipping brush for cleaning the saw band

Condition: excellent (used), IMM 72780 Double-sided polishing machine Mint condition, the machine has hardly been used. TECHNICAL DATA Nwsdpfx Asu Hanyjhvsc Polishing wheel: 100 - 500 mm shafts: 35 mm Spindle speed: 1500 rpm Voltage: 400 V, 50 Hz Weight of basic machine: Approx. 400 kg No responsibility is taken for the correctness, completeness and up-to-dateness of the information.

Condition: new, MEP SHARK 281 CCS metal band saw with semi-automatic lowering. Item number: SH281CCS motor power 1,5/1,8 kW band opening 285 mm band dimensions 2950x27x0,9 mm weight 375Kg Speed 36/72 m/min. cutting surface 0° 250 / 230x230/ 280x200 cutting area 45° right 190 / 180x180/180x180 Cutting surface 45° left Cutting surface 60° right Cutting surface 60° left Description: -Saw band arch, vise unit and base made of resistant cast iron. -Precision degree marking on the cast iron structure -Electrical system (with fully identifiable electrical wiring and low voltage 24 V system) -Switching handle IP 55 for manual cycles (if present) -Rotating scraper brush for the saw band -Closing unit with vice for fast approaching -Accurate stops with adjustment for miter cuts at 0°, 45°, 60° on the left side -bi-metal saw band 2950 x 27 x 0,9 mm -Wrench, instructions for use and instructions for ordering spare parts in the user's language -SHARK 281 with manual operation and SHARK 281 CCS with manual operation and cut with automatic head feed by own weight. -CCS (Cut Control System) with (A switch for manual and automatic cutting - B) regulation of cutting speed - C) hydraulic brake with tank - D) end stop for stopping the belt) also available as an option for machines already in production. -Vice with quick adjustment -Hydraulic transducer for belt tension indication -Electric coolant pump for cooling and lubrication of the saw band and manageable coolant tank above the base frame -For the versions with pneumatic vice (MA), the opening and closing of the vice is done with a manual valve (available as an option with pedal control) MEP SHARK 281 SXI evo [Semi-automatic] Part number SH281SXI motor power 1,5/1,8 kW belt opening 285 mm belt dimensions 2950x27x0,9 mm weight 435 kg Speed 36/72 m/min. cutting surface 0° 250 / 230x230 / 280x200 cutting area 45° right 190 / 180x180 / 180x180 Cutting surface 45° left Cutting surface 60° right Cutting area 60° left Description Semi-automatic function: Vise closes and motor starts, saw head lowers for cut, motor shuts off, saw head raises, vise opens. Some features: - New centralized control panel on articulated arm. Nodpfecgbp Iox Ahvswc - Latest generation hydraulic control unit, highly efficient and with low energy consumption. - Base with extractable coolant tank. The machine complies with CE regulations in all areas! For further technical data, please refer to the attached PDF document.

Condition: new, cutting diameter 250 mm saw band length 2950 x 27 x 0,9 mm table height ca. 800 mm band speed 36/72 m/min total power requirement 1,5/1,8 kW weight of the machine ca. 0,37 t dimensions of the machine ca. m MEP sawing machine: Saw band bow, vice unit and base made of durable cast iron Precision grade marking on the cast iron structure Electrical system (with fully identifiable electrical wiring and Low voltage system 24 V) Nwedpofg E H Ijfx Ahvjc Switch handle IP 55 for manual cycles (if available) Rotating scraper brush for the saw band Clamping unit with vice for quick approach Accurate stops with adjustment for miter cuts at 0°, 45°, 60° left Bi-metal saw band 2950 x 27 x 0.9 mm Keys, instructions for use and instructions for ordering spare parts in the User language SHARK 281 with manual operation and SHARK 281 CCS with manual operation and cutting with automatic head feed by its own weight. CCS (Cut Control System) with (A switch for manual and automatic Cutting – B) Cutting speed regulation – C) Hydraulic brake with tank – D) End stop for stopping the belt) also optional for already produced machines available. Vice with quick adjustment Hydraulic converter for belt tension display Electric coolant pump for cooling and lubricating the saw band and manageable coolant tray above the base frame In the versions with a pneumatic vice (MA), the opening takes place and Closing the vise with a manual valve (with pedal control as option available)

Year of construction: 2007, condition: ready for operation (used), An Amada CNC turret punching machine for medium format sheets including an MP300 M loading unit, Wilson X-Sharp grinding machine and numerous standard and special punching tools are available. 1) CNC turret punching machine Amada, year of manufacture: 2007, punching force: 300kN, max. sheet dimensions X/Y: 3000mm/1500mm, max. sheet thickness: 6.35mm, stroke rate: 600 strokes/min, simultaneous positioning speed: 128m/min, repeat accuracy: +/-0.1mm, machine dimensions X/Y/Z: approx. 5100mm/3200mm/2300mm, weight: approx. 18000kg. 2) Automatic sheet loading and unloading system Amada MP 300 M, max. sheet dimensions X/Y: 3000mm/1500mm, min. sheet dimensions X/Y: 1000mm/300mm, sheet thickness range: 0.8mm-6mm, max. load capacity per pallet: 3000kg, max. stacking height: 400mm, max. sheet weight: 170kg, max. pallets: 9, pallet change time: 25s, sheet loading time: 18s, weight: approx. 4900kg. 3) Wilson X-Sharp tool grinding machine. Documentation available. On-site inspection is possible. Nsdpjwhp N Djfx Ahvswc

Condition: as good as new (ex-display), functionality: fully functional, type of cooling: water, FRONIUS TPS 5000 ✅ Scope of delivery: ➤Fronius TPS 5000 power source (500A TRANS PULS SYNERGIC) ➤Fronius FK 4000 ➤Fronius VR 4000 wire feeder unit ➤Fronius standard intermediate hose package from 1.5m ➤Fronius trolley ➤Fronius hose package ➤Ground cable 3-4m ➤Pressure regulator This device can weld almost all materials, including aluminum, steel, and V2A. It features touch wire programs and is also suitable for MIG brazing (Cusi), which is frequently used in the sheet metal industry. Additional options and applications: This TPS series can be easily connected to a robot. All you need is an interface and the appropriate hose package. We also offer the optional RCU 5000i control panel, which allows you to create and import characteristic curves to further expand the functions of the TPS device. ---- IMMEDIATELY AVAILABLE PROPER INVOICE A viewing is possible in Austria in Vienna, 1230! ✔ Insured shipping on a pallet is no problem! ✔ ✅Questions✅Questions✅Questions: ✅Questions✅Questions✅ Questions✅ ►►►What is the condition of the device? To explain, we buy like-new used devices, disassemble them, check everything, replace wear parts if necessary, and only then, after successful test welding, is the device released for sale. "All" devices are clean and have neither burn holes in the displays nor countless burn holes or dents scattered throughout the device! You are buying an item from us that is also worth seeing and doesn't look completely finished! ►►►Do we receive an invoice when we purchase from you? Yes, we provide a proper invoice. If you have a valid VAT ID, we can issue a net invoice if the requirements for intra-community delivery within the EU are met. ►►►What payment options are available? Advance payment or cash upon personal pickup ►►►Is insured shipping possible? Yes, we will be happy to send you the purchased set well packaged and insured on a Euro pallet. ►►►Is there a warranty? We sell the machines at one-third the original price and unfortunately do not have the flexibility to offer a warranty. You are welcome to test the devices on site and pay in cash. Nwsdpfx Ajwbh Ifshvec ►►►Why buy from us? We are experts in this Fronius welding machine series and always have 60-80 devices in stock – exclusively Fronius, no other manufacturers! We are experts in these devices and don't sell anything we don't know about.

Condition: used, CNC flame cutting machine BACH type ACW 2500 Flame cutting machine with CNC control NBS 400 Machine. No. 14 561-06 Year of construction 2006 Cutting area 2500 x 6500 mm track length 8000 mm Track width 3345 mm Njdpfx Ahsf Ncadevswc Track height 650 mm 2x machine cutting torch with cutting table