Balers

Maschinenfabrik Bermatingen GmbH &CO.KG, Dixi 60SLD

Condition: used, SINGLE SHAFT SHREDDER WEIMA MODEL WLK15 MAIN MOTOR 90KW ROTOR KNIVES SIZE 50X50 (NEW KNIVES) ROTOR LENGTH 1500MM ROTOR DIAMETER 370MM THE MACHINE IS 100% FUNCTIONAL Kdodpfx Anotqd Ndexjl READY TO WORK

Condition: excellent (used), Manufacturer: Strautmann Model: PP 1207 Plus Bale size (LxWxH): 1200 x 1100 x 730 mm Bale weight: approx. 400 - 500 kg Kdsdjv Aiymjpfx Anxol External dimensions (LxWxH): 1850 x 1047 x 3079 mm Transport height: 2500 mm Filling opening: 1190 x 600 mm Pressing force: 59 tons / 580 kN Throughput: 1 - 2 bales/hour Number of ties: 4 Press weight: 2300 kg Power supply: 400 V / 50 Hz Power consumption: 4 kW Installation location: covered indoor/outdoor Noise level: less than 80 dB(A) Year of manufacture: 2003-2005 I also have Strautmann PP 1207 balers from 2009-2011, price 5,500 EUR Also available: Strautmann PP 1208 balers from 2014-2015 Strautmann AutoLoadBaler year 2018, price 7,500 EUR

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 500 h, functionality: fully functional, machine/vehicle number: 25-029, total width: 800 mm, total length: 4,700 mm, total height: 1,900 mm, type of input current: three-phase, energy consumption: 2 kWh, Very good metal separator (inductive sorter) for separation of all kinds of metal (incl. stainless steel). Can be used before ECS, behind or stand alone. Ejecting of all metals larger 0.5 / 1 mm possible. Reasonable using for material up to 60 % metal content. Unique flap technology, no pressured air necessary. Machine is ready for using, can be visited or tested. If wished can be equipped with camera. Kdodpoqabm Ejfx Anxel If the machine is too small we can build also bigger. It is our demonstration machine. Throughput / capacity depending on material and purpose. Price on negotiation!

Condition: not inspected (used), Year of construction: 1985, functionality: fully functional, pressing force: 50 t, bale length: 1,000 mm, bale width: 750 mm, bale height: 750,750,750 mm, bale weight: 500 kg, input voltage: 400 V, overall weight: 7,500 kg, oil tank capacity: 500 l, power: 30 kW (40.79 HP), empty load weight: 7,500 kg, input frequency: 50 Hz, Manufacturer: Paal Typ: Pacomat V Year of construction: 1985 Press power main press: 50 t Specific press capacity: 5 kg/cm² Feed channel: 1.000 x 720mm (l x w) Theoretic throughput rate: 200 cbm/h Bale size: 700 x 1.000 mm (w x h) length adjustable Ksdpfx Ansic Rl Doxodl Driving motor: 30 kW Bale weight: approx. 500 kg Machine weight: approx. 8000kg The hydraulic unit is functional, the drive motor is in the removed state.

Year of construction: 1999, condition: used, System: Used decanter / centrifuge Manufacturer: Baker & Hughes Model: full coat screw centrifuge Type: CP 3054 Year of construction: 1999 Hoechstzul. Speed: 3132 I/min Inner diameter drum: 552 mm Drum wall thickness: 14.5 mm Engine: 2 electric motors, new Auger motor Control Panel: no Frequency converter: Yes Kjdpfscbukrox Anxodl Documentation: Yes Maintenance: regularly twice a year In operation: By early 2015 Buying and renting possible.

Condition: good (used), Year of construction: 2002, Beringer BPx4 ergo Useful volume 6cbm tested, serviced, fully functional Can be painted in the desired RAL color. Kdsdpfxotp Hnwe Anxsl Noes3koku We would be happy to make you an offer including delivery.

Condition: new, Klanke Supercut roll splitter for efficient shredding of reject rolls. Features: -Automatic safety lock -Emergency stop rip cord -Siemens SPS Technical data: Blade length: 3000mm Cutting channel opening: 1200mm Kdedpfxsn I Rgpj Anxel Motor power: 15kW Cutting force: 50to Order goods Price and further information on request. We will be happy to make you a non-binding offer.

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 1,400 kg, overall weight: 36,000 kg, oil tank capacity: 1,300 l, For sale is a overhauled baler, with 100 tonnes pressing force, large format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Kedpfx Asvf E Avenxjdl Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press was tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: used, No. 10028 Cable granulation plant FRS BK 60 Used According to our customer, the machine is fully functional and can be inspected and tested on site Cable granulating system for up to approx. 1000 kg of cable per hour (according to our customer) Motor and blades were renewed in 2025 Rotor dimensions 610 x 500 mm Kodpfxoxwdndj Anxsdl 14 blades Motor power 45 kW Incl. magnetic conveyor belt Cylinder size 400 x 120 mm Motor power 1.5 kW Incl. sieve with two outlets Motor power 0.35 kW Installation dimensions approx. 7000 x 6000 mm LW Transport dimensions approx. 6000 x 2400 x 2600 mm LWH Weight approx. 6000 kg Sale on behalf of customer, ex location near 69123 Heidelberg, without dismantling, without transport and assembly Dismantling, transport and loading by us optionally possible Errors in the description and price reserved To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Pictures and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipment Terms of delivery: ex location

Year of construction: 2017, condition: ready for operation (used), Material throughput: LDPE: 110kg/h, PA6.0/LDPE/EVOH: 150kg/h, PP/PA6.0/LDPE/EVOH: 135kg/h, PA6.0/LDPE: 120kg/h, EVA/LDPE: 150kg/h. Nominal output: 77kW, PCU output: 30kW, extruder output: 18.5kW, motor output: 10.7kW, heating zones: 1, heating output: 12kW. Documentation available. On-site inspection is possible. Kodpowty Hkjfx Anxjdl