Hydraulic guillotine shears

LVD MG-31/16-20

Year of construction: 2002, condition: reconditioned (used), Beam cutting, drilling and marking line DISC SAW Brand: KALTENBACH Model: HDM 1431 / T13 / SP-CNC Year 2002 Serial number: 122.400 Weight without accessories: 10,980kh - Disc saw with downward cut. - Geared saw unit, drive system and saw blade on wear-resistant swivel bearing. - Heavy saw gear with pinions in oil bath, with inclined teeth, hardened and sharp. - Hydraulic advancement of the saw blade, adjustable according to the table, very fast recoil. - Hydraulic horizontal clamping device. Rear clamping jaw with long-stroke clamping cylinder and automatic recoil limitation. - Vertical clamping block with self-adjusting push plate. - Oblique cutting device to adjust the angle from 45° to the left to 35° to the right. - Material sensor to automatically switch from rapid advance to work advance. - Hydraulically elevating feed roller for optimum material transport on the saw table. - Economical lubrication by means of a micro-dosing installation, especially suitable for sawing profiles. - Chip collector installed on the machine bench. Specs: - Cutting disc housing: 100x4x30x250mm - Cutting disc diameter: 1,430mm - Cutting width: 9.5mm - Cutting speed: 10 to 20m/min. - Saw advance speed: 0-400mm/min. - Fast reverse speed: 2000mm/min. - Total power: 25KW - Working height: 640mm Cutting capacities: 90º cut - Angle steel: 250mm - Steel in U: 400mm - Double T-beam: 600mm - Wide flanged beam: 1008x302mm - Special wing beams: 1000x450mm Cut to degrees: IPBv beam - 75º: 1008x302mm - 60º: 910x302mm Cgjdpfx Ajhzbipoa Eep - 45º: 716x304mm - 40º: 716x304mm - 35º: 478X307mm IPBs beam - 75º: 1008x402mm - 45º: 524x357mm IPE beam - 45º: 600x220mm DRILLING UNIT Brand: Kaltenbach Model: KDX1215 Serial number: 122.401 Work capabilities: - Angular steel (minimum - maximum): 80x65x10mm - 250x250x28mm - Steel in U (minimum - maximum): 80x45mm - 400x110mm - Double T beam (minimum - maximum): 80x46mm - 600x220mm - Wide flanged beam (minimum - maximum): 100x100mm - 1,008x302mm - Extra wide wings beam: 1,200x500mm Drilling units: 3 - Vertical (Y axis) 1 pc. - Horizontal (Z and W axes) 2ud. Drilling diameters: 8 - 40mm RPM: 150 - 1100 Fast forward - Fast reverse: 3,850mm/min. - 8,000mm/min. Drilling spindle feed rate: 0-500mm/min. Fast spindle positioning tool: 15,000mm/min. Automatic tool changer: 5 u. in each drilling unit. 3x5 u. = 15 total Total power: 45KW MARKING UNIT FEEDING: 26 METERS OF ENTRY WITH BEAM FEEDER + 6 SIDE ARMS FOR BEAM ENTRY IN PARALLEL TO THE ROLLER TRACKS 30 METERS OF ROLLER TRACKS WITH OUTPUT + 6 SIDE ARMS 4 SIDE ARM FOR SMALL PIECES THE GREAT MAJORITY OF ROLLERS ARE MOTORIZED It occupies approximately 60 linear meters between input and output power. *Request machine installation plans.

Condition: good (used), Year of construction: 2010, X Y Z: 1270 x 508 x 508mm, table 1324 x 457mm, 12000 rpm, BT 40, HAAS Control, 24 Station ATC, 40HP, chip auger, coolant, Haas TR210 5 axis trunnion table Codexpw Rvjpfx Aa Esgp

Condition: used, Combined profile steel shear and hole punch GEKA type HYD 80 / Hydracrop 80/A Machine. No. 9566 Year of construction approx. 2000 Cgodjrz Tutepfx Aa Eop Punching force 80 ton. throat 300 mm Punching up to Ø 40 mm in 14 mm sheet metal Flat material shears 450 x 15 mm Angle steel shears 130 x 130 x 13 mm Square shears 45 x 45 mm Round material shears Ø 45 mm Rectangular notcher up to 12 mm Motor power 5.5 kW Mains connection 400 Volt, 50 Hz - Fence with el. stroke release 500 mm - Work table with stop for punching device 550 x 380 mm - Working height of the punching device 1100 mm - Work table with stop for the rectangular notcher 550 x 400 mm - Working height of rectangular notcher 930 mm - approx. 21 different punching tools - operating instructions - Original paint finish, not repainted Space requirement L x W x H 1800 x 1150 x 1950 mm Weight 1.7 tons. very good condition

Condition: new, Year of construction: 2025, ZGR-3140/1,0 Our products are best quality and have certificate CE. Plate Bending Machine ZGR-3140\1,0 + additional equipment Codpfx Ascntnkja Ejgp Technical data: - Maximum working width: 3140 mm - Sheet gauge up to: 1,0 mm (Steel) - Titan-Zinc-Plate 1,0 mm, Aluminium Plate 1,8 mm Cooper plate 1,5 mm - Max. bending angle: 145 degrees - Rotary shears cut to full working length - Thickness of bending bar: 20 mm - Protractor - Weight: 600 kg - Rotary shears (max. plate gauge 0,8 mm / Steel) + 350 Euro - The machine have certificate CE and 12 months warranty.

Condition: good (used), Offer freezer for freezer production. Various spare parts available. Motors only replaced two years ago. Fully functional. Collection only in 93437 Furth im Wald Sale without guarantee, warranty and return Codpfxst I Eyco Aa Eogp

Condition: used, CNC Press Brake AMADA Type HFBO 50 x 2000 Serial No. HFBO 50 20 S60906 Year of manufacture: 1996 Press brake with 8 axes - CNC control Operator II Pressing force: 50 tons Working length: 2090 mm Stroke: 200 mm Frame depth: 420 mm Distance between side frames: 1660 mm Max. tool installation height: 460 mm Table width: 60 mm Table height above floor: 910 mm Motor power: 4.5 kW Mains connection: 400 Volt, 50 Hz, 20 Amp. - 8-axis CNC control Operator II (Y1-Y2 / X1-X2 / Z1-Z2 / R1-R2) - 2 freely programmable backgauge fingers, movable laterally and in height (Z1+Z2+R1+R2) - Press beam with servo valves and measuring system Y1 and Y2 - Operation via electric foot switch and/or two-hand control panel - Mechanical lever-style tool clamping for the upper tool (5 AMADA Expert, 5 UKB 50.667 H=120 mm) - Tool holder for lower tool, 60 mm wide - 11-piece upper tool set, 30°, total length 1675 mm - consisting of: 1x 835 / 1x 300 / 1x 165 / 1x 50 / 1x 45 / 1x 35 / 1x 20 / 1x 15 / 1x 10 / 2x 100 mm (end pieces) in length Cedpfxew Iq Ugs Aa Ejgp - 2-piece lower tool, 88° - V8, total length 1250 mm - consisting of: 1x 835 / 1x 415 mm in length - Indicated operating hours: 30,537 h - Operating manual, electrical diagram, spare parts book included Weight: 4,700 kg Good condition

Year of construction: 1993, condition: ready for operation (used), Includes aggregate weigher, cement weigher, water weigher, additive weigher, special material weigher, Schlossermixer and Biotronik control system, documentation available, on-site inspection is possible. Cedpfx Aajq Ttz To Ejgp

Condition: used, Miter cold circular saw KALTENBACH type KKS 400 NA Machine. No. 101701 Year of construction 1983 saw blade diameter 400 mm cutting range at 90° round Ø 130 mm sawing range at 90° square 120 x 120 mm sawing range at 90° rectangle 305 x 20 mm Cutting range at 45° round Ø 130 mm Sawing area at 45° square 110 x 110 mm Cutting range at 45° rectangle 245 x 30 mm Cgsdpjd N H A Nofx Aa Eop Clamping range of collet feed 30 to 140 mm Working height 1000 mm miter cut 0 - 180 feed path 600 mm Saw blade speed 10 + 20 m/min. 2 steps motor power 1,7 and 2,6 kW hydraulic motor 1,5 kW Mains connection 380 Volt, 50 Hz - Hydraulic material clamp feed with infeed roller conveyor left 1500 mm - Feed path via double feed up to 1200 mm (2x feed, then sawing) - Hydraulic material clamping with vertical clamping cylinder - miter cut - saw angle with manual adjustment - hydraulic feed control, cutting speed manually adjustable - 2 motor speeds for the saw blade speed - saw blade stroke steplessly adjustable - coolant unit with electric pump in the machine base - Hydraulic unit fixed to the basic machine - Parts counter with zero cut-off space requirement of the saw 2600 x 1200 x 1900 mm weight of the saw approx. 1400 kg good condition

Condition: ready for operation (used), Year of construction: 2012, This is a side seam wicket bag machine Lemo Intermat 850 STN-CP Knoter, production type: wicket bags for bread, chicken, diapers, toilet paper, hygiene products and other types of wicket bags, number of lanes: single lane / lane wicket, processable materials: LDPE, HDPE, PP and recycled extracts, sealing width (bag length): 120-450mm, draw length (bag width): 200-850mm, gripper arm length: 600mm, max. linear speed: 65m/min, output capacity: 140 knot bags/min, max. number of bags per stack: 250, drive system: PLC-controlled, operator interface (terminal), print mark control, servo motor drive, nip feed rollers, sealing bars. Attachments and accessories: bottom gusset (only bottom gusset included), handle unit, longitudinal sealer, pre-sealer, angle sealer, cross sealer, handle punch, photo cell for printed film, automatic one-step conveyor (index conveyor), handle hole punch, G-gusset unit, V-gusset station, web guiding system 1800mm, anti-static bars, automatic labeling system. Machine is in good condition. Cgjdpfx Ajw U T T Eoa Eep

Condition: excellent (used), Year of construction: 2008, For sale complete PVC carpentry production line, brand URBAN, composed of: *1. Welding machine at 2 ends; URBAN brand, model: AKS 5305-FF, serial number: 53372, year of manufacture: 2007, perfect working condition; *2. Channel milling machine; URBAN brand, model: WS 103, serial number: 790, year of manufacture 2007, perfect working condition; *3. 2-headed saw: brand RAPID, model DGS 100, serial number: 004606128, year of manufacture 2010, sold together with vacuum cleaner with bags, perfect working condition; *4. MACC rebar cutting saw, model NEW 275, serial number: 88266, year of manufacture 2008, perfect working condition; *5. Pantograph brand URBAN, model MLA A23 – 100466321S, serial number: 528-0, year of manufacture: 2008, perfect working condition; 6. Upright milling machine: URBAN brand, model M7CRH-100149891, serial number 559, year of manufacture 2008, perfect working condition; *7. De burring machine with 2 groups of cutters; brand URBAN, model SV 280, serial number: 29342, year of manufacture 2008, perfect working condition; *8. Saw for cutting sticks: brand URBAN, model GLS 102; serial number: 102015; year of manufacture 2010, perfect working condition; The production capacity of the line is 30-50 units/8h (depending on the number of people serving the line). The line was used very little from 2010 to 2014, and not at maximum capacity. We can also sell individual machines on request from the line. Net price complete line 33.500 Euro + VAT, negotiable, FCA Oradea. Csdpfx Aaoucl Dcj Eogp