Thermoforming machine

Kiefel KMD 52 BFS

Condition: reconditioned (used), Max. forming area: 960 x 660 mm Min. forming area: 210 x 170 mm Max. sheet size: 1000 x 700 mm Min. sheet size: 310 x 210 mm Max. sheet thickness (manual feeding): 12 mm Max. sheet thickness (automatic feeding): 10 mm Max. tool height: 490 mm Iisdpfswf Dvaox Aa Ejd Max. draw depth: 300 mm (positive/negative) Total power consumption: approx. 64.0 kW / 115 A Technical features: - Siemens Simatic S7-300 control, OP 37 panel - Air-conditioned control cabinet - Top heater with 5 temperature control circuits via pilot emitters - Bottom heater with 5 temperature control circuits via pilot emitters - Individually switchable top heating elements - Individually switchable bottom heating elements - Parallel clamping frame - Pneumatic motor locking for the upper reduction frame - Cylinder locking for the lower reduction frame - 4 cooling fans - Adjustable vacuum for the lower table via cascade control - Pre-blow and demolding adjustable via cascade control - Large front opening for tool change - Film sag control by photocell with support air - Automatic tool change system Lower table: 1. Tool clamping via vacuum 2. Tool change via pneumatically operated ball rollers Upper punch: 1. Motorized remote adjustment for stroke limitation 2. Pneumatic quick-change system for tools Sheet feeding: - Automatic motorized lifting of the film transport chain - With pneumatic quick-clamping system for vacuum plates - Motorized centering of plastic sheets - Separate vacuum pump for grained material Optional preheating retrofit: - Pneumatically moved top heater, complete zone control, each emitter individually switchable via toggle switch - Pneumatically moved bottom heater, complete zone control, each emitter individually switchable via toggle switch - Temperature control of top and bottom heating via separate heating controllers in the BE control cabinet (temperature setting not via UA control panel) Optional retrofit for roll processing: - Cross cutter and feeding rollers in feed area - RO 800 roll stand

Condition: good (used), Year of construction: 1990, operating hours: 45,350 h, machine/vehicle number: 1537, Hybrid machine for sheet or coil thermoforming. Equipped with a BE-type plate feeder without preheating. Equipped with a PR-type coil unwinder. Equipped with an upper and lower table. Ijdetv Ivzopfx Aa Ejid Managed by a Schleicher PDPF order manager. Quick clamping of reduction frames and tooling maximum width 700 mm maximum plate size 1000x700 maximum sheet thickness 10 mm We take care of dismantling and loading onto your truck, which is available for collection.

Condition: excellent (used), Complete line direct from Bankrupt company which was filling capsules and tablets into small tubs. Bottlea are loaded into the line from lazy susan, product is counted and doses into the tub or bottle which is then foil sealed before the screw lid is applied. All machines were bought new in 2015 and appear to be in excellent condition. The counter is a Vitacount 12-1 Iedpfxow Hz T Eo Aa Eeid

Condition: as good as new (ex-display), Year of construction: 2022, functionality: fully functional, machine/vehicle number: AM00222090802-01-03, - Function: Heat sealing of blister boxes - Main material of the machine: Stainless steel 304, aluminum alloy - Dimension: 1000mm x 715mm x 450mm - Weight: About 150 kg (excluding mould) - Power supply: 220 V 50 / 60 Hz single phase 3,5 KW - Compressed air supply: Pressure 5 bar - 8 bar, approx. 18 L / min - Seal size: 300mm x 400mm - Packing depth: Deepest 100mm - Production speed: Up to 12 cycles per minute depending on operator skill - Heat seal pressure: 300-1500kg adjustable Autovak is an international company with research, development and manufacturing facilities in Suzhou, China, and sales and service offices in the United States, Germany and Malaysia. The company has over 20 years of experience in the packaging of medical devices. Isdpfjpfcy Esx Aa Eeid From doing OEM for European packaging machine manufacturers to produce self-designed machinery and equipment with independent intellectual property rights and own brands, Autovak has accumulated a lot of know-how in the field of medical device packaging and online printing.

Condition: as good as new (ex-display), operating hours: 50 h, Uhlmann thermoform packaging system UPS 4 ETX for processing PVC forming film and aluminum lidding film Basic machine in modular technology and balcony construction, with 12 modules: - Molding film holder with 2 pneumatic clamping shafts for core diameter 76 mm, max. roll diameter 800 mm - Cutting and gluing table for shaped film - Shaped film unwinding, clocked - 3-zone contact heating: - 6 heating circuits, individually adjustable - Simultaneous heating of min. 3 feeds - Heating plates during machine stop automatic opening - Forming station with 4-column lifting table guide - Filling section, length 1,360 mm - Safety flap on the filling section Cover film unwinding on operating side with pneumatic expansion shaft for core diameter 76 mm, max. roll diameter 300 mm - Plate sealing station with 4 columns lifting table guide: - Integrated overload protection - Automatic lifting of the upper sealing sealing tool when the machine stops - Free module for the installation of an additional station - Clamping gripper feed - Punching station with blister lowering - Waste cutter with integrated motorized transport of the punching grid - Smoothing device - ET/DT perforating station - Monitoring of the compressed air supply with machine stop when the minimum the minimum value - Visio Scan - Electrically interlocked safety doors - Quick format change due to - plug-in format parts - Plug-in connections for cooling water supply - Main drive with frequency-controlled three-phase motor geared motor - Switch cabinet at the rear of the machine, swivel-mounted Paccontrol operating control - 10.4" TFT color display with 640x480 pixel resolution - Processor 68C030 - OS9 2.9 operating system - 2 MB SRAM, 2 MB Flash, 16 MB DRAM - SRAM card reader - IBM standard membrane keyboard - Centronics interface for external printer - PS2 interface for external keyboard - VGA interface for external monitor - Serial interface for diagnostic purposes - Arcnet interface - 8 serial interfaces for connecting devices Integrated shift register ISR Isdpstndpzjfx Aa Eoid Rejection of individual blister rows, e.g. overheated film in the heating station, products in the sealing station, etc. Machine control: Memory-programmable sequence control in modular design: - B&R - PLC control - Bus system with modules for CPU, inputs, outputs, temperature controller, cam controller, etc. - External program memory Technical data UPS 4 ETX: - Number of cycles: - ET range: min./max. : 15/ 50 T/min. depending on film quality, feed and format design - Format range: min./max. feed in filling area : 64/226 mm min./max. film width : 100/300 mm min./max. punching width : 28/284 mm max. drawing depth : 12 mm - Compressed air: - Inlet pressure: approx. 6 - 8 bar 4 Simtap feeders

Year of construction: 2006, condition: good (used), Illig SK 74-C from a workshop for the disabled Year of construction 2006 serial no.426-0172 +2 pallets with approx. 38 rolls of film Iodpfx Aajr Nv E Ne Ejid Dimensions in mm approx. 2200x1600x1600

Condition: like new (used), Year of construction: 2016, operating hours: 390 h, functionality: fully functional, type of input current: three-phase, overall weight: 827 kg, Carrier water chiller Model: 30RBS-140B0181-ME, year 2016, R410A. 135 kW (116,100 frigories), cooling only, maximum consumption: 61 kW. Dimensions: 2258x2050x1330 mm, plate heat exchanger, weight: 827 kg. Machines fully tested in our warehouse with gas, inspection possible. Reference: 1137. Iiedpfx Aajyfwuzj Eod

Condition: good (used), machine/vehicle number: 897, Jaw width: 160 mm Jaw height: 50 mm Span: 280 mm Iodpfeb Dimvex Aa Esid Overall height: 130 mm

Year of construction: 2012, condition: excellent (used), Category: Twin-screw extruder Number: DE27691 Iedpfx Aaevk Sgfs Esid Manufacturer: Feddem Type: DEC 72 MTS Year of manufacture: 2012 Capacity: 400 – 700 kg/h Screw diameter: 2 x Ø 72.0 mm L/D: 32D, including housing extension to 42D Drive: 168 kW Material: PE, PP, PS, ABS // Additional details: Co-rotating extruder, degassing – 2 side feeders, 6 Schenk gravimetric dosing units, ECON EUP 600 underwater pelletizer, Trendelkamp classifying screen, degassing, vacuum pump, BSG control system Very nice complete system with only approximately 3,500 operating hours. The offer doesn't meet your requirements? Please visit our website: "Plama Engineering" or send us your detailed inquiry, we have the right product for almost every budget.

Condition: good (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 589-0263, Make Illig Model VHW 60/2 Year 2001 Condition Good Number of Heating Rolls Two Max material width 610 mm Ijdeuzi I Ejpfx Aa Eoid Max material thickness 1.8 mm Max temperature of heating rolls 140 °C Material wrap around 563 Grad Total connected load 36.0 kW Dimensions 2300 x 1400 x 2400mm L x W x H (300kg) All details are subject to change and/or errors. All equipment is subject to availability and/or prior sale