HUNDEGGER K2 4 assi

HUNDEGGER K2 4 assi

Condition: good (used), Year of construction: 2011, Fully automatic wood infeed with feed roller conveyor Extension of transverse feed conveyor and feed roller conveyor for timber lengths up to 13 m Transverse loading and feed conveyor Lsdpfjwuppwjx Anceaa Under-table swing cross-cut saw Universal 4-axis milling unit (UF4) Combination support for vertically operating tools Drilling unit 2.2 kW Combination support for horizontally operating tools Drilling unit 2.2 kW Longitudinal and transverse grooving mill Marking device at the rear (stop side) Fully automatic beam turning station – hydraulic Transport and positioning device "two-hand system" Electronic control with EKP software Roller conveyor for wood outfeed incl. extension (without drive) Component ejector 5-arm wood rack Safety devices and protective guards

Year of construction: 2011, condition: used, functionality: fully functional, Finger jointing line for cross sections up to 200 cm² (80/240 mm or 100/200 mm), with the following. components: 1. HOWIAL tilt unstacking - SH/4t - 1,75x1,75x6,00m - 4t - short. Length 2,50 m, semi-automatic separation of the package. Lodji Ezx Dopfx Anceaa For tilting the wood pile up to 45°. Electric motor drive. stack dim. max. 1,75 x 1,75 x 6,00 m max. stacking load 4 t shortest wood length 2,5 m 2. HOWIAL - VE 1 lamella separator for crosscut saw. With pneum. controlled tongues, on which the material is marked for defects, deposited on the roller conveyor below. 3. HOWIAL - evaluation roller conveyor RO-1 digital wood moisture measuring, control and recording system for autom. recording and control of wood moisture in cycle measuring method according to electric resistance principle. 4. gann DMT-8 dig. Wood moisture measuring, control and recording system for automatic detection and control of wood moisture in the cycle measuring method according to the electrical resistance principle. Plant in large switchboard complete with ink jet printer. 5. HOWIAL - crosscut saw AS-30 B pneum. Under table crosscut, with 2 autom. feed units, autom. crosscut. Special photocell control for detection of fluorescent line markings. Automatic waste disposal possible. Saw motor power 7,5 kW saw blade diameter 700 mm feed drive approx. 2 x 1,5 kW Air pressure 8 bar feed speed max. approx. 60 m/min. 6. HOWIAL - conveyor belt cut off waste, with studded belt and guide plates belt width 350 mm belt 2000 mm long belt speed 0,4 m/sec. 7. HOWIAL - double roller conveyor RO-2 6,00 m long incl. transversal transport, drive by round belt, all rollers driven. Cross transport chain conveyor. Ejection ± moisture right Transport speed adjustable 100 m/min. length approx. 6,00 m Width of rollers approx. 400 mm Diameter 112 mm 8. compact finger jointing machine Cook Bolinder The technical data are original from Cook Bolinder: wood width from 75 to 245 mm Timber thickness from 20 to 105 mm Input lengths from 1m to 6 m Cross sections from 30 cm² to 200 cm² Pressing force 5 - 22 to Spindle diameter 50 mm tine profile 15/15 spindle speed approx. 6000 upm Total electrical connected load approx. 62 kW Machine weight approx. 9 to. Gluing OEST comb system for PU Modern Telemechanique SPS control. 9. HOWIAL - Roller conveyor with destacking system Driven roller conveyor with autom. ejector and hydr. driven destacking arms. Technical data: H: 920 mm L: approx. 12.000 mm 10. safety fences incl. circuit breaker 11. finger joint testing machine BSPLT-100 Testing machine for finger joint bending test according to DIN 1052-1/A1 and EN 385 Support distances freely adjustable, attached dimension scale, autom. calculation of support distances in the software. Fully automatic test procedure by mouse click on PC (not included). Alternatively, the test procedure can be started by key operation on the front panel. Connection of any commercially available PC or laptop (Win 2000/XP) via the supplied RS232 serial cable. Fully automatic measured value logging as well as automatic logging in MS-Excel with graphical display. Representation max. wood width: 300 mm max. wood thickness: 140 mm max. compression force: < 100 kN max. support length: 2100 mm Measuring accuracy WITHOUT DISMANTLING

Condition: good (used), Year of construction: 1995, functionality: fully functional, WORKING DIMENSIONS: 400x250 mm Ljdpfx Aox S E Haencjaa 4 SIDES + EDGE BEVELERS

Condition: used, Year of construction: 2003, functionality: fully functional, machine/vehicle number: 11441, At the moment we are working with the following version: 9.23.12.102733-12 The equipment of the K2: a 4-axis universal milling machine 2 drilling rigs a finger cutter below a slotter Laedpfxjwvih Aj Ancsa Hydraulic beam turning station Machine is fully working, can be visiited upon agreed time. avaible from 01/05/2026 Disassembly from our company and loading to truck, and is included in the price. Sale is as a used machine with exclusion of any warranty.

Condition: excellent (used), Year of construction: 2003, machine/vehicle number: 11470, functionality: fully functional, workpiece width (max.): 450 mm, Hundegger K2 in very good condition, overhauled, rebuilt, and commissioned by Hundegger. Since then, it has only run for about 20 hours and was professionally dismantled and stored in a heated hall. Laedpfx Aewhpavencsa

Condition: used, Used machine Year of manufacture: 1991 Fully automatic vertical machine, Cutting area 5,300 x 2,200 mm (cutting width x cutting height), Saw blade diameter 300 mm, Control for vertical and horizontal cuts, with ALU folding stops and ALU center support, with SUPER-CUT scoring unit Motor 3 kW - 400 V Lsdpfx Aex Rr D Aencoaa Availability: short-term Location: Röllbach

Condition: excellent (used), Year of construction: 2018, The line consists of: - WEINMANN OPTIMAT WTZ 120/12 L assembly table - WEINMANN WMS 150 - WEINMANN OPTIMAT WTW 110/12 N/L loading/unloading table - Schmalz Jumbo Ergo 140 flexible hose vacuum lifter The WMS150 multifunction bridge is a CNC machine for the automated processing of timber structural elements (walls, roofs, and floors). Machine dimensions: - Length (X-axis): approx. 3,000 mm - Width (Y-axis): approx. 6,200 mm - Height (Z-axis): approx. 3,000 mm - Workpiece width: approx. 3,200 mm - Main spindle: 18.5 kW with automatic tool changer - FLEX5 indexing system Tool set for WMS tool changer consisting of: - 3-flute universal roughing cutter - Drilling unit - Saw unit - Marker with ballpoint pen technology HSK - Saw unit NL 55 mm HSK63F - Saw unit NL 105 mm HSK63F Gluing system - Holder for PUR gluing unit - PUR one-component adhesive unit (1K) with 6 application nozzles Fastening and assembly unit - Automatic height adjustment for fastening device - Holder for ADUNOX screwdriving unit - ADUNOX-TRS screwdriving unit Bridge extension Tool holder beam with integrated Y-axis Sliding guide with U-profile for the bridge Increased X-axis drive dynamics Energy supply system via cable drag chain Lsdpfxeytyuao Ancoaa End position monitoring for handling systems Wheel and sliding block lock, right side of portal Homatic powerControl V2.0 control system Remote control for WMS150 with potentiometer Mobile extraction unit 3.0 kW Electrical cabinet cooling unit Less than 1,000 operating hours

Condition: ready for operation (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 1779, The K1 was rebuilt in 2020 and equipped with the latest safety features. It is currently dismantled, stored covered outdoors, and can be loaded immediately. Lasdpfx Anex Ehmaocea

Condition: used, machine/vehicle number: 005289, X axis working area: 7400 mm Y axis working area: 1550 mm Working Table: Flat table Main Electrospindle power: 11 KW Number of controlled axes: 4 axes Lodswcyacepfx Ancsaa Total number of drilling spindles: 10 Total number of tool changer positions: 14

Condition: excellent (used), Year of construction: 2018, functionality: fully functional, Double table machining center Working range X 2,590 mm Laedsuqw E Nopfx Ancea Working range Y 2,260 mm Working range Z 400 mm Number of milling spindles 2 Liquid-cooled spindle Main motor 19.2 kW Max rotational speed 24,000 rpm Aggregate heads 4 C-axis Tool clamping system HSK-F63 Tool change positions central magazine 24 Tool change on each head from 12 positions Boring heads vert. 20 (for each head) Horizontal boring heads X 8 Horizontal boring heads Y 8 Blade for grooves in X, in Y 2 Platens Number 4 360 m³/h vacuum pumps T Jet system for chip blowing Nesting Manual labeling Bar code reader Tool length measurement Software BIESSE BIESSEWORKS ADVANCED, BIESSE B_NEST Weight 17,900 kg