Top Sanders

HOMAG SANDTEQ W-700

Condition: excellent (used), Year of construction: 2019, functionality: fully functional, Working height: 900 mm Working width: 1,350 mm Belt changing side: left Workpiece thickness: 3 - 160 mm Frequency-controlled feed speed: 4 - 20 m/min Abrasive belt dimensions: 2,620 x 1,350–1,380 mm Adjustable sanding belt blowing device with 5 settings WRD WORKPIECE CLEANING ROTOR Workpiece cleaning system with 16 rotating nozzles MOBILE OPERATING TERMINAL powerControl with powerTouch Isdpfx Aqeyw Ndmeuoic SST SOFT STARTER Inrush currents are limited to prevent voltage drops GWRD BELT CLEANING PROGRAM Upon activation, the machine automatically sets to a 10 mm workpiece thickness and activates the blowing rotors. After the feed belt is fully cleaned, the machine returns to its initial setting. AAT EXTRACTION DAMPER CONTROL Control of extraction dampers via the terminal (24 Volt DC, without extraction dampers included) UPS EMERGENCY POWER SUPPLY FOR BELT CONTROL 1-3 PCS Uninterruptible power supply for sanding belt oscillation in case of power failure System consists of: SANDTEQ W-700, PROFI SWB735/RRE – sanding from below Wide belt sanding machine with three sanding units for processing wood or wood-like workpiece surfaces Prepared to accept up to two auxiliary units, such as a cleaning brush, satinizing or structuring brush, and rotating cleaning nozzles. Units: I. R UNIT Sanding unit with automatically adjusting contact roller Profiled steel roller, 240 mm diameter With grain compensation Drive motor: 37 kW Abrasive belt speed: 25 m/s - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking - Pneumatic abrasive belt tensioning with integrated belt edge compensation II. R UNIT Sanding unit with automatically adjusting contact roller Rubber-coated roller, 240 mm diameter Rubber hardness: 85° Shore With grain compensation Drive motor: 30 kW Abrasive belt speed: 18 m/s III. E UNIT Sanding unit for installing a pressure beam - Automatic locking of the sanding unit for fast belt changes and increased process safety - Abrasive belt drives with electronic, wear-free brake - Optical, touchless abrasive belt tracking - Pneumatic abrasive belt tensioning with integrated belt edge compensation - Protected storage area on the machine for additional sanding inserts Drive motor: 22 kW Abrasive belt speed: 2 – 18 m/s Torque-dependent standby operation to reduce energy consumption. ACP PNEUMATICALLY SUPPORTED PRESSURE BEAM - Adjustable sanding pressure via pressure regulator - Workpiece-controlled engagement and disengagement at the leading and trailing edges - Various sanding inserts, 80 mm wide, with different felt hardnesses Machine dimensions (L x W x H): 3,900 x 2,100 x 2,000 mm Machine weight: approx. 7,500 kg SANDTEQ B-700, PROFI SWT735/RRE – sanding from above Wide belt sander with three sanding units for machining wood or wood-based workpiece surfaces Units as above, additionally: FBM FINISHING BRUSH Brush unit with finishing brush Bristles: horsehair Diameter: 130 mm Drive motor: 0.75 kW Machine dimensions (L x W x H): 2,995 x 2,100 x 2,255 – 2,415 mm Machine weight: approx. 6,500 kg

Condition: good (used), Year of construction: 2012, Automatic panel saw for chip-free and dimensionally precise cutting of coated and uncoated wood-based panels and materials that can be processed like wood-based panels. Control panel on the right. Iiodpfx Asy N R Scequoc Scoring saw Cutting length: 4300 mm Cutting width (program pusher travel): 3100 mm Roller tables: 4 pcs Two-finger clamping grippers Required space approx. 6520 x 6550 mm Data taken from the documentation. All details without guarantee. Availability: Expected December 2026

Condition: new, Year of construction: 2026, Efficient, quiet, and powerful mechanical machine Technical specifications: Working length: 4040 mm Total length: 5352 mm Depth: 2232 mm Working height: 950 mm Total height: 1924 mm Weight: 5,000 kg Maximum bending thicknesses: Steel: 1.5 mm Aluminum: 2.00 mm Stainless steel: 1.00 mm Copper: 2.00 mm Galvanized sheet: 3.00 mm Standard equipment: • 1 bending rail, 20° with sharp nose, radius 1 mm, offset, 66/24 mm for the clamping beam • 1 insertable rail, 10/100 mm and 24/100 mm for the bending beam • Foot switch (MAF 400/CNC model delivered with a second foot switch) • Soft start for the bending beam • Electrically driven back gauge, 8-1000 mm • 5 m power cable with 32 A mains plug (EU version) • Supply voltage: 3 x 400 V, 50 Hz (EU version) CNC S-Touch control: From profile concept to bending precision in record time Standard features at no extra charge: • Graphical display of the bending sequence for the selected program • Graphical representation of sheet position before every bend • Operator guidance – each work step visually explained via the graphic control system • Programming without submenus • Profile correction by direct touch in the desired section of the profile • Programmable angle correction Ijdpfx Aqex Hyhbsueic • Set repeat cycles for special radius arcs • Cutting program for RSL rotary shears • Easy mode for: single bends, back gauge, bending angle, lifting height, closing edges • Profile search possible by name, sketch selection, and profile drawing on the touchscreen • 21.5-inch LCD touchscreen with best-in-class graphics • USB port for program backup and transfer • Non-volatile memory for over 3,000 programs • Freely assignable program names (profile names) • Registration of produced quantities and machine operating time • 16 languages • Remote support (Team Viewer) • Soft start for bending beam • Back gauge with drive, 6-1000 mm • Foot switch For EU market: • 16 A plug with 5 m power cable • For MAF and MAZ models, 32 A plug with 5 m power cable

Condition: new, Type SK-1000-P6 Working width 1000 mm Min.working length 500 mm Working thickness 2-150mm Polishing roller speed - Frequency control Feeding speed 3-12,5 m/min Total motor power 13.87 kW Disc motor 1.5 kW*1 Iodedmi Nijpfx Aqusic Cross motor 1.5 kW *1 Screw roller motor 2.2 kW *2 Feeding power 2.2 kW Up and down motor 0.37kW*4 Swing motor 0.37kW *2 Working table up and down 0.55 kW Transport dimensions 3650x1850x2100mm Weight 4200 kg

Condition: used, machine/vehicle number: 008027, Max. machining width: 1350 mm Min. machining thickness: 200 mm Working Table: Fixed pass height Iiodpfjwvq E Aox Aqusc Vacuum feed belt: yes No. Operating units: 4 Nr

Condition: used, Year of construction: 2008, machine/vehicle number: 0-411-49-1873, Technical data: - Manufacturer: Bütfering - Type: Optimat SGO 211/RC - Number of grinding units: 2 - Year of manufacture: 2008 - Working width: 1.100 mm - Grinding belt width: 1.120 mm - Grinding belt length: 1.900 mm - Workpiece thickness: 3-160 mm - Feed speed: 2,5-13 m/min. - Table height adjustment Standard equipment: - Automatic workpiece thickness adjustment - Stepless feed speed via requency converter. - 125 grinding programs can be stored - Wear-free braking system 1. Grinding unit (R) - Calibration roller - Profiled steel contact roller - Diameter 160 mm - Drive motor: 15 kW 2nd grinding unit (C) - Combination unit with roller and grinding shoe - Rubberized contact roller 65 Shore - Contact roller diameter 160 mm - Electronic link pressure bar with segment width 35 mm. - Belt speed: 12 and 21 m/s - Tolerance compensation up to 1 mm - Suitable for veneered surfaces and solid wood. - Drive motor: 11 kW - Total connected load: approx. 28 kW - Operating voltage: 400 V / 50 Hz. - Compressed air consumption at 6 bar, 20 L/min. - Belt blow-off device per pressure surge 440 L/min. - Extraction volume: approx. 2,880 m3/h/ at 20 m/s - Extraction connection: Iedpfx Aoyh Hwuequsic Dedusting: 1 x Ø 160 mm (grinding unit, roller) 1 x Ø 160 mm (grinding unit, shoe) Dimensions: - Length: 1,700 mm - Width: 1,850 mm - Height: 2,100 mm - Location: not in stock - Available from April 2026

Condition: excellent (used), Year of construction: 2006, Technical data: - working width 1350mm - pneumatic oscillation - vacuum table Iiedpfx Aovdtxiequsc - Stand alone machine ( Table raise/fall ) 1 Combi unit: - motor power 18,5kW - steel calibrating roller - stepless adjustment of the belt speed - sectional pad (52 sections of 26mm each) 2 Combi unit: - sectional pad (52 sections of 26mm each) - motor power 7,5kW - stepless adjustment of band speed - brush on the exit of the material - stepless regulation of feed speed - pneumatic cleaning of belts

Condition: like new (used), Year of construction: 2018, Single Head Cutting Machine with Ascending Blade Ø 600 mm Single head cutting machine with ascending blade Ø 600 mm, designed for precise and versatile cuts. - Worktop rotation: manual, up to ±20°, both to the right and to the left. - Preselected angles: quick positioning on 90° and 45°. - Intermediate angular positioning: manual with pneumatic locking for any cutting angle. - DIGIT: equipped with digital display for precise positioning of the cutting angle. - MQL: minimal quantity lubrication system for efficient tool management. - Cutting unit rotation: up to ±20°. Technical Specifications - Blade diameter: 600 mm - Blade hole: 50 mm - Blade rotation speed: 2800 rpm - Motor power: 4 kW - Dimensions (L x W x H): 920/1520 x 1320 x 1525/1800 mm Iisdpfx Aov I N Eysquoc - Weight: approx. 470 kg

Condition: reconditioned (used), Year of construction: 2010, Voltage 400V 3~ 50Hz 7.22kW Control panel with LCD display and keypad Jointing unit with 2 counter-rotating diamond cutters Corner rounding unit for edge faces Manual unit adjustment Iodpfeyf I T Usx Aqueic Edge thickness 0.4-5.0 mm (optionally 8 mm) Workpiece height 8-60mm Feed speed 11 m/min 3 free slots for finishing units Edge feed for coil and strip material Scraper knife

Year of construction: 2012, condition: excellent (used), Window production line WEINIG Isdpfeh H Iyxjx Aqujic consists of: Unirex 3000 machining center Univar 15 Unitex 15