Work center

HOMAG

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, workpiece height (max.): 40 mm, edge thickness (max.): 3 mm, feed rate X-axis: 35 m/min, rotational speed (max.): 12,000 rpm, number of slots in tool magazine: 48, TECHNICAL DETAILS Panel height min.: 10 mm Panel height max.: 40 mm Edge thickness min.: 0.4 mm Edge thickness max.: 3 mm Feed speed max.: 35 m/min PROCESSING UNITS Pre-milling unit Automatic engagement 48 tool positions End trimming unit 2 motors Fine trimming unit 1 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Fine trimming unit 2 Lodpsyqybuofx Ahvshd 2 motors Motor power: 0.55 kW Speed: 12,000 rpm Edge scraping unit Glue scraping unit Polishing unit 2 motors Spraying device MACHINE DETAILS Control system: PC 22 EQUIPMENT Pressure applied with rubber belt Panel guides with NC positioning Glue pot for EVA hot-melt adhesive Pre-melter for EVA hot-melt adhesive Laser system (Model: LaserTec) Roller set for edge pressing with 5 pressure rollers Units mounted on safety guards CE marking The machine is sold and delivered in its actual and legal condition (“as seen and approved”), based on photo documentation and technical/commercial descriptive documentation. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, securing, and use of the machine at the destination. External reference: 5321

Condition: used, Number of boring spindles 10 St. Working width 230 mm Ljdjw H Iv Tspfx Ahvshd Working height 160 mm Feed motor 5,5 kW Feed speed 6-36 m/min.

Condition: not inspected (used), Year of construction: 2007, functionality: unexamined, working width: 1,935 mm, number of spindles: 40, plate height: 350 mm, working length: 6,200 mm, number of axes: 4, TECHNICAL DETAILS Working area X-axis: 6,200 mm Working area Y-axis: 1,935 mm Maximum panel thickness: 350 mm Number of edge tape magazines: 3 Number of tool positions in tool magazine: 22 (located at the rear of the machine) Drilling spindles Spindles for vertical drilling: 28 Spindles for horizontal drilling in X direction: 4 Spindles for horizontal drilling in Y direction: 8 Total number of vertical + horizontal spindles: 40 Milling spindles Number of controlled axes: 4 Motor power: 10.5 kW Automatic tool changer Lhjdpfx Aheyqx U Heved MACHINE DETAILS Total connected load: 31 kW EQUIPMENT Suction cups for securing the workpiece Safety mats at the front Vacuum pump Waste chip conveyor Fixed groove unit for slotting in X direction The machine is sold and delivered in its actual and legal condition (“as seen and approved”) on the basis of photographic documentation and descriptive technical/commercial documents. The buyer has the right to inspect the item prior to collection and assumes responsibility for installation, securing, and operation of the machine at the place of destination. External reference: 8105

Condition: not inspected (used), Year of construction: 2005, functionality: unexamined, power: 19 kW (25.83 HP), travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,730 mm, number of spindles: 20, number of tool stations in tool turret 1: 18, TECHNICAL DETAILS Working area X-axis: 4,175 mm Working area Y-axis: 1,730 mm Number of suction traverses: 8 Tool magazine positions: 18 Spindles Number of spindles for vertical drilling: 17 Number of spindles for horizontal drilling (X-direction): 2 Number of spindles for horizontal drilling (Y-direction): 1 Total number of spindles: 20 Ljdpfxoyttf Sj Ahvjhd Milling unit Number of controlled axes: 4 Motor power: 18.5 kW Automatic tool changer Liquid-cooled MACHINE DETAILS Total installed power: 19 kW Control model: PC85 EQUIPMENT CE marking Front safety cover Note: Cones, milling cutters, and aggregates are not included in the scope of delivery. Safety fences are supplied based on availability (left side only). The machine is sold and delivered in its actual and legal condition (‘as seen and approved’), based on photographic documentation and technical/commercial documents of a descriptive nature. The buyer is entitled to inspect the goods prior to collection, and assumes responsibility for installation, safety, and use of the machine at the destination. External reference: 6906

Condition: reconditioned (used), For Sale: EOS P100 – Ready for Immediate Use KNOW WHAT YOU BUY! Fully revised and with warranty! This EOS P100 has been fully inspected and revised, making it ready for immediate use in your production environment. Included in the package: Ledsrm Tdwopfx Ahvshd • 2 build frames • Set of hoppers Specifications: • Technology: SLS (Selective Laser Sintering) • Material class: Polymers • Compatible materials: PA2200, PA3200, PA2201, Inframotion PA12, TPU, and more. • Build volume: 200 x 250 x 330 mm • Laser type: Synrad 48-3, 30W CO2 laser • Minimum wall thickness: 0.4 mm Consumables Highlight We offer a wide range of plug-and-play materials, fully tested and optimized for use with EOS machines. Our Inframotion PA12 delivers top performance and provides significant cost savings compared to OEM powders, without compromising on quality. Choose our exclusive materials to drastically reduce your operational costs. Included Services: • Transport & Installation: Safe delivery in original EOS packaging and professional installation included. • Warranty & Maintenance Plans: Flexible options tailored to your specific needs. About Inframotion 3D (IM3D) At Inframotion 3D B.V., we specialize in high-quality refurbished EOS SLS machines with comprehensive support. As the only provider offering a complete solution for used EOS equipment, we distinguish ourselves through extensive expertise and unique services. What we offer: • Expert maintenance: Installation, servicing, repairs, and upgrades performed by experienced ex-EOS technicians. • Exclusive materials: Cost-effective, high-quality consumables such as our plug-and-play PA12, specifically designed for EOS machines. • Complete support: From transport to maintenance plans, we handle it all. Trust IM3D for reliable machines, superior materials, and the expertise to optimize your SLS production. Feel free to contact us for more information or inquiries!

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, travel distance X-axis: 4,175 mm, travel distance Y-axis: 1,550 mm, workpiece height (max.): 40 mm, number of spindles: 30, travel speed (max.): 80,000 mm/min, TECHNICAL DETAILS Lsdpfx Aoyttcwshvehd Travel range X-axis: 4,175 mm Travel range Y-axis: 1,550 mm Travel speed X-axis: 80 m/min Travel speed Y-axis: 80 m/min Travel speed Z-axis: 30 m/min Maximum workpiece height: 40 mm Number of suction traverse beams: 8 Spindles Number of spindles for vertical drilling: 20 Number of spindles for horizontal drilling in X-direction: 10 Total number of spindles: 30 Milling unit Number of controlled axes: 4 + Flex5 Motor power: 15 kW Automatic tool changer Liquid-cooled Saw unit Tool magazine 1 Number of slots: 18 Tool magazine 2 Number of slots: 10 EQUIPMENT NC positioning of suction units Vacuum pump PowerControl P85 control system WoodWop 5.0 machine programming software Note: Cones and milling cutters are not included in the scope of delivery. The machine is sold and delivered in its actual and legal condition ("as seen and approved") on the basis of photographic documentation and technical/commercial documents of a descriptive nature. The buyer has the right to inspect the goods before collection and is responsible for installation, securing, and usage of the machine at the destination. External reference: 7350

Condition: not inspected (used), Year of construction: 2008, functionality: unexamined, edge thickness (max.): 3 mm, feed rate X-axis: 25 m/min, rotational speed (max.): 12,000 rpm, TECHNICAL DETAILS Minimum edge thickness: 0.3 mm Maximum edge thickness: 3 mm Maximum feed speed: 25 m/min MACHINE DETAILS Edge Processing Unit 1 Unit: End Trimming Model: WK13 Number of motors: 2 Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 2 Unit: Top Milling Number of motors: 2 Motor power: 0.55 kW Max. speed: 12,000 rpm Edge Processing Unit 3 Unit: Multifunction Model: FK13 Number of motors: 2 automatic tool changer with NC positioning Motor power: 0.4 kW Max. speed: 12,000 rpm Edge Processing Unit 4 Unit: Top Mill Model: UF11 Number of motors: 1 Motor power: 4 kW Max. speed: 9,000 rpm Edge Processing Unit 5 Unit: Edge Scraper Model: MN21 with NC positioning Edge Processing Unit 6 Unit: Glue Scraper Model: FA11 Edge Processing Unit 7 Unit: Brush Number of motors: 2 Motor power: 0.25 kW Edge Processing Unit 8 Unit: Brush Number of motors: 2 Ledpfx Aheytr Hbjvehd Motor power: 0.25 kW Total installed power: 35 kW EQUIPMENT Spray unit PowerControl PC22 machine programming software CE marking The machine is sold and delivered in its actual and legal condition ("as seen and approved") based on photographic documentation and descriptive technical/commercial data. The buyer has the right to inspect the goods prior to collection and assumes responsibility for installation, safeguarding, and use of the machine at the destination. External reference: 6216

Condition: used, Year of construction: 2012, operating hours: 10,000 h, functionality: fully functional, cutting width (max.): 800 mm, insertion depth: 800 mm, insertion height: 150 mm, cutting length (max.): 800 mm, overall weight: 500 kg, type of input current: three-phase, total width: 160 mm, total length: 200 mm, input voltage: 400 V, Equipment: documentation/manual, safety light barrier, The MOHR 80 cutter is engineered for single-shift operation and features a precise, gentle swing cut actuated hydraulically, allowing the dwell time of the knife at the lower dead point to be tailored to the material. The ultra-smooth stainless-steel table, fitted with air jets, makes material handling effortless. Clamping pressure is infinitely adjustable via a scaled rotary knob to accommodate a wide range of cutting materials. High-visibility LEDs clearly indicate the cutting line for the operator. Operation is carried out through an ergonomically positioned 18.5’’ touch-screen display. The machine can store up to 1,998 cutting programs for rapid recall and flexible adaptation of recurring sequences. Integrated into a digital workflow, cutting data can be received directly from pre-press into Compucut® in ppf- or jdf-format, which then automatically generates the appropriate cutting program. A barcode reader enables automatic program retrieval and execution, effectively reducing set-up times to nearly zero. Process visualization graphically displays material handling, significantly minimizing error risk. To further optimize cutting quality, the pre-clamping time can be adjusted based on the material being processed. Key features: - Barcode reader for automatic creation and loading of assigned cutting programs via Compucut® - Process visualization for graphical representation of material handling, minimizing error risk Ljdpfx Ajxwnxgshvehd - Rigid machine frame engineered for optimal stability, maximizing absorption of cutting forces and ensuring superior cutting accuracy - Minimal maintenance requirements thanks to the use of advanced materials Technical specifications: - Cutting width: 800 mm (31.49 in) - Feeding depth: 800 mm (31.49 in) - Maximum feeding height: 100 mm (3.93 in) - Clamping pressure: minimum 180 daN (397 lbs), maximum 2,700 daN (5,953 lbs) - Backgauge speed (return): up to 130 mm/sec (5.12 in/sec) - Minimum automatic cut without false plate: 15 mm (0.60 in) - Minimum automatic cut with false plate: 50 mm (1.96 in) - Dimensions (W × D × H): 1,430 × 1,970 × 1,500 mm (56.29 × 77.55 × 59.05 in)

Condition: used, machine/vehicle number: 008395, X axis working area: 3050 mm Y axis working area: 1250 mm Lhjdpfsygtcqjx Ahved Main Electrospindle power: 10 KW Number of controlled axes: 3 axes Total number of drilling spindles: 27 Total number of tool changer positions: 8

Condition: used, machine/vehicle number: 007985, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt Premilling Unit: yes Corner Rounding Unit: yes Ledpfx Ahjx A Th Dovjhd Operating Units: 7 nr

Condition: used, Year of construction: 2014, CNC Machining Center Biesse skill 12 24 G FT Year of construction 2014 Lodpfewnhansx Ahvehd Machine no. 60961 Recording HSK F63 10x vertical drilling 12 switch positions Software: BiesseWorks X axis 2465 mm Y-axis 1260 mm Z axis 324 mm Disassembled for transport on normal trailer; 4500x2200x2400mm; Own weight 2000kg - Year: 2014 - Documentation available: Yes - CE certificate present: No - Tool clamping system: HSK-F63 - Drilling unit present: Yes - └ Vertical drilling spindles [pcs.]: 10 - Tool changer positions [pcs.]: 12 - Working range X [mm]: 2465 - Working range Y [mm]: 1260 - Z-axis working range [mm]: 324 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: used, machine/vehicle number: 008323, Type of edging: Thin edge, Thick edge, Solid wood Gluing System: EVA Hotmelt, PUR Premilling Unit: yes Corner Rounding Unit: yes Max feed speed: 20 m/min Ledpfx Asx Hpkxjhvehd Maximum panel thickness: 60 mm Operating Units: 7 nr

Condition: used, machine/vehicle number: 005980, Squaring: First and Second Pass Max Panel Thickness: 120 mm Lhedpfxsxcf S Ie Ahvsd Max feed speed: 20 m/min Distance between dogs: 1000 mm

Year of construction: 2015, condition: new, We have a MATICA Espresso card printer available. This printer is bought by us in 2015 and has been standing in the showroom. Price new ist € 1.599,-, price now is € 999,- We have come to the conlcusion that this type of machinery is not the type of machinery we are able to offer as a distributor in a correct manner. Therefore this printer is new and has just printed max 10 cards in its life. Single or double side edge-to-edge Ledefnldqspfx Ahvjhd Optional Magstripe and Smart Card encoder Ethernet and optional WiFi Prints up to 850 cards per hour 100-card feeder The Matica Espresso II is a compact and powerful desktop ID card printer, that is a brainchild of Italian design & engineering and reflects German reliability in consistent performance. The Espresso II offers great value and versatility with extraordinary printing speed and outstanding print quality. With its robust and durable construction, the Espresso II looks and works great in any office or card production environment. The Espresso II is a single side desktop ID card printer for projects needing printing only on one side. The Espresso can be field-upgraded to easily double the printing capacity with the duplex printing feature. Any Espresso II printer can evolve to duplex anytime, anywhere without the need to install additional hardware components. Contact and contactless smart card encoding are also field-upgradable features. LED status indicators on the front of the printer allows you to monitor the card production process at a distance, and the blue LED light on the card hopper door keeps you aware of your card input availability in real time. You can also use optional single card manual insertion for individual card printing as needed. Each printer comes with a rear output hopper to catch full card runs as needed, which can improve the throughput speed in higher volume scenarios. In standard setup, having front-side input and output trays is also convenient for situations where space is limited, in a desktop environment, a cabinet or under a counter. Each Espresso II printer also has the option for inline magnetic stripe, contact chip or contactless smart card encoders, to maximize its functionality for a broader set of application uses, such as access control, time & attendance, payment services, and many more. The entire line offers Ethernet connectivity and optional WiFi making printing and encoding convenient and trouble-free. You can easily define your printer and choose the one that perfectly matches your current needs, as Espresso II offers a vast range of options. Whether or not your requirements evolve in the future, you have still the possibility of making an upgrade by adding functionalities to your existing configuration. The new printer line works perfectly for a wide variety of applications such as Employee and Membership ID Badges, Service and Benefits Cards, Gift and Loyalty Cards, Access Control Cards, Student IDs, and Transit Cards, just to name a few. The Espresso II is available with different specifications ​— modules, encoding, color, etc..

Condition: used, machine/vehicle number: 008324, Max. panel width: 1000 mm Lhjdpfx Ahsx Hpkrsvsd Max. panel length: 2500 mm Length of conveyor: 7000 mm Panel return for edgebander: Right