Lathe - cycle-controlled

Helmerding Leit- und Zugspindeldrehmaschine

Condition: like new (used), functionality: fully functional, Weiler center lathe model Condor B lead and feed spindle lathe with 3-axis digital readout from K&C NEW Geometrically overhauled with acceptance certificate for tolerances of new machines !!! Technical data: >> Machine no. 90-1495 >> Center height 165 mm >> Center width 750 mm >> Spindle speed : from 22 to 2800 rpm >> Spindle clearance 40 mm >> Short taper spindle head DIN 55027 size 5 with bayonet lock >> Tailstock MK 3 >> Feed rates from 0.015 to 0.46 mm /rev >> Possible threads metric, inch, module and diametral pitch >> Metric thread pitches from 0.18 to 28 mm >> Weight approx. 1100 kg >> Spindle brake can be activated >> Length 1.83 m, height 1.29 m, depth 0.88 m Accessories and equipment: >> 3-axis digital readout from K&C New , 12 months manufacturer's warranty with operating instructions Functions : Switching mm/inch , Coordinate selection ABS/INC , Halving of the display value , Reference mark , Tool programming 200 pcs. , Cone calculation , Radius / diameter , Quick zeros , Switching the counting direction , >> Collet chuck device, collets NEW from 3 to 26 mm 1 mm increasing >> Three-jaw chuck 160 mm with 2 sets of jaws NEW >> Mulifix new size A with 2 steel holders new >> Bed stop >> elec. Chuck guard NEW >> Machine lamp LED New >> Rear panel >> Operating instructions >> Coolant device >> Machine feet Lhodevambcopfx Ad Nsb To the machine : We are offering a Weiler Condor B lead and feed spindle lathe in a geometrically overhauled condition, absolutely as good as new. The guides are newly ground and scraped. With acceptance according to test protocol. A very nice machine with electronic spindle protection. The accessories collets, chuck, Multifix are new. Spindles, spindle nuts, bearings, belts, wipers have been renewed. Take the opportunity to inspect this machine on site under power and see the condition for yourself.

Condition: used, turning diameter / mm turning length / mm swing diameter over bed slide / mm Technical data - Model 230 DIMENSIONS Centre height on the bed: 230 mm Spacing between centres: 1000-1500 mm 2000-2500 mm 3000 mm Bed width: 360 mm Largest turning Ø: on the bed: 465 mm on the carriage: 278 mm on fixed steady rest: 200 mm on travelling steady rest: 160 mm CROWNING Ljdpfxewz Rywe Ad Njhb Width of the crank: 300 mm Distance between face plate edge and offset: 150 mm Largest turning Ø on the offset: 690 mm SPINDLE Ø of front bearing (inside): 110 mm Ø of rear bearing (inside): 95 mm Ø of hole: 77 mm Mounting Type - Cam Lock: 6" Internal spindle taper - taper: 1 : 20 Spindle taper - C. M. - N.: 5 Speed ranges: Slow feed - rev. 1': 15÷1000 Normal feed - rev. 1': 22÷1500 Fast feed - rev. 1': 30÷2000 FEEDS (without gear change)-N.: 108 Longitudinal feed range at revs. : 0.04÷4 mm Transverse feed range at revolution: 0.02÷2 mm Lead screw - Ø: 40 mm Lead screw pitch: 12 mm THREAD (without gear change) Metric - N. 54 to: 0.5÷28 mm Module - N. 54 to Module: 0.25÷14 Whitworth - N. 54 to Wt. x 1": 56÷1 Diametral Pitch - N. 54 to D.P.: 112÷2 Inch - N. 54 to Inch: 1/32 ÷ 13 3/4" SPINDLE PIT Quill Ø: 75 mm Quill barrel: 220 mm Quill taper - vices N. 5 POWER Main motor - HP: 10 Pump motor - HP: 0.25 WEIGHT approx. - kg 2000-2220 2530-2720 2920 ON REQUEST Main motor - HP

Condition: good (used), Centre height: 195 mm Distance between centres: 1250 mm Max. swing diameter over bed/cross slide: 400/265 mm Spindle mount/bore: Camlock D1-6"/54 mm Tailstock quill taper: MT 5 Spindle speeds steplessly adjustable in 3 ranges: 0 - 2500 rpm Longitudinal feeds: 0.018 - 1.2 mm/rev Cross feeds: 1/2 of longitudinal feeds 51 metric thread pitches: 0.2 - 14 mm 56 imperial (inch) threads: 2 - 56 TPI Lsdpexlg Dwofx Ad Nehb 20 module threads: 0.2 - 3.5 module 20 diametral pitch threads: 8 - 56 DP Electrical connection: 400 V, 7.5 kW Weight: 1500 kg Space requirement: 2500 x 1300 x 1300 mm

Condition: ready for operation (used), functionality: fully functional, spindle bore: 42 mm, center height: 165 mm, center width: 635 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 30 rpm, overall weight: 900 kg, Ladies and Gentlemen, Lhjdpfx Aeu St S Ajd Nsb We are selling a Colchester Master 2500 lathe with Heidenhain digital readout. The machine is fully functional and can be tested on site. Availability: immediately Center width: 635 mm Center height above bed: 165 mm Center height above support: 105 mm Spindle bore: 42 mm Spindle speed: 30 - 2500 rpm. 16 steps Inner tailstock taper: MK 3 Drive power: 3.7 kW Space requirement: (LxWxH) 1700 x 880 x 1200 mm Weight: approx. 850 kg

Condition: used, Year of construction: 2003, machine/vehicle number: 1527, Used lead and feed screw lathe COLCHESTER Triumph VS 2500 Ljdpex Hrumsfx Ad Nehb Centre height: 195mm Distance between centers: 650mm Spindle bore: 54mm Infinitely variable speed: 14–2500 rpm Tailstock quill: MT5, coolant system, quick thread cutting device Digital readout: FAGOR NUP 300 TS-RS 1 x RÖHM 3-jaw chuck, 5-position stop drum, spindle stop, machine lamp, 1 x PARAT 4-way turret, 4 x PARAT tool holders, live centre and quick-action drill chuck. The machine is located at our premises in 71334 Waiblingen-Beinstein and is available immediately. Inspection of the machine is possible by appointment.

Year of construction: 1980, condition: ready for operation (used), Center height: 210mm, distance between centers: 1500mm, swing over bed: 420mm, spindle bore: 57mm, speed range: 38–2000/min, main drive: 7.5kW, weight: 2t. Equipment: 3-jaw chuck, tailstock, steady rest, quick-change tool holder, coolant system, lighting, year of manufacture: approx. 1980–1985. No data sheet, fully functional, well maintained, ready for immediate use. Only slight oil moisture in the lower area due to age, without relevant oil loss. An on-site inspection is possible. Lhsdpfjxtprasx Ad Njb

Condition: good (used), functionality: fully functional, turning diameter: 400 mm, turning diameter over top slide: 240 mm, center height: 200 mm, turning length: 1,100 mm, total length: 2,500 mm, total width: 1,100 mm, total height: 1,900 mm, spindle speed (max.): 2,500 rpm, overall weight: 1,500 kg, three-jaw chuck diameter: 240 mm, TECHNICAL SPECIFICATIONS & EQUIPMENT: Operating voltage: 380 V Frequency: 50 Hz Rated current: 21 A Spindle speed: 75–2500 rpm Spindle bore: approx. 52 mm Ljdpfx Adow U Tn Ne Njhb Centre distance: 1100 mm Centre height over bed: approx. 200 mm Swing over bed: 400 mm Centre height over cross slide: 120 mm Swing over cross slide: approx. 240 mm The machine is equipped with a tailstock, a Multifix tool holder, and a 3-jaw chuck Diameter: 240 mm Including two-axis digital readout by manufacturer FAGOR REFERENCE NUMBER: 14 DIMENSIONS & WEIGHT: 2500 x 1100 x 1900 mm 1500 kg PICK-UP INFORMATION: The item will be available from September 2025. A collection date must still be arranged on a specific day from 01.09.2025 onwards FCA: 73235 Weilheim an der Teck (DE), loaded onto truck

Year of construction: 2015, operating hours: 5,000 h, condition: ready for operation (used), General Data Machine weight 1800kg Main Drive Spindle speed range 2500 This Colchester Triumph VS 2500 was manufactured in 2015. It features a conventional pull and lead screw, infinitely variable speed adjustment, and a digital display. Key specifications include a turning diameter of 400mm, center height of 195mm, and a bed width of 1270mm. It also comes equipped with a MultiFix quick-change tool holder, maximum spindle speed of 2500rpm, and a motor power of 7.5kW. Weight is 1,800kg. Contact us for more information about this machine. Application Types Lhsdjx D Nwdepfx Ad Neb Turning

Condition: good (used), machine/vehicle number: 86388, Weiler Condor 81 Lead and Feed Screw Lathe Turning length: 750 mm Centre height: 165 mm Spindle bore: 40 mm Speed: 45–2,800 rpm Ljdpfex Sd Hfsx Ad Njhb Dimensions (LxWxH): 1,832 x 880 x 1,290 mm With Heidenhain digital readout and extensive accessories!

Condition: good (used), 1 x lead and feed screw lathe Matra MDR 210 Lsdpfex Rum Tox Ad Nohb Nice machine from a small toolmaking shop. Additional data and photos will follow. The machine can be inspected under power from 13.01 onwards.