Horizontal Machining Centre

HELLER PT 16

Condition: new, AVAILABLE EX STOCK ! Subject to prior sale. OD tube deburring machines clean and remove sharp edges on tubes and profiles caused by sawing. Nledpfsd Ixbzsx Afrsi Enables simultaneous outside and inside burrs removal without rotating the tube. Deburrs round, square, rectangular and many different tube and profile shapes deburring in few seconds.

Condition: new, Year of construction: 2024, New machine Year of construction: 2024 Equipment and technical data: Right-hand version Technical data: Overall dimensions: 1,900 x 1,410 mm Hopper opening: 1,044 x 1,044 mm Hopper height: 1,010 mm Hopper capacity: 1.1 m³ Drive power: 5.5 kW Briquette diameter: 50 mm Hydraulic oil: 160 l Throughput: up to 50 kg/h (depending on material) Paint finish: Weima Standard Connected load: 400 V +/- 5 % / 50 Hz including: Press mechanism with filling cylinder, main cylinder, gripper cylinder Nlodpfx Aot Hagnjfrei Connecting part for transport line Chrome-plated tongs Hydraulic tank 160 l with pump motor + valve control Safety switch for oil temperature Base plate 1,040 x 1,040 mm with agitator + motor and screw channel Screw channel Discharge screw + motor Side walls standard height 1,010 mm Base frame with rubber feet Switch cabinet on hopper and electrical control system Briquette length monitoring Automatic end position of all cylinders Manual control Automatic "On/Off" with level switch Material: Wood shavings, sawdust from solid wood, loose, clean and free of foreign matter*/ Dimensions: max. 12 mm Throughput capacity: approx. 50 m³/year/ * Specification foreign matter: Everything except wood, pieces of wood larger than 12 mm. The throughput capacity is highly dependent on the material. Average values are given. Depending on mixing ratio, moisture and material properties! Application not or not fully known/specified. Machine is sold appropriately and sold by the specialist dealer in accordance with the solution. In the event of heat build-up, the running time can be drastically reduced in accordance with the heating. Availability: short term Storage location: Solingen

Condition: used, Year of construction: 1999, control Siemens 840D Nedpfx Ajqn A Rvjfrjli Number of axles 4 St. 2 toll turrets 160 tool taper HSK 63 spindle turning speed range 24.000 U/min filter unit Ja chip conveyor Ja kW

Condition: reconditioned (used), Year of construction: 1989, Dear Sir or Madam, for sale is a partially overhauled Deckel FP1 with 3-axis TNC113 active control, which is particularly distinguished by its ease of operation. This newer version from year of manufacture 1989 has among other things a central lubrication, an electric coolant pump and a machine lamp. The machine has been extensively overhauled in our workshop and is therefore in excellent condition. You can convince yourself of this on site. In the course of the partial overhaul, among other things, the following work was performed: - Spindle bearing of the milling head renewed - Repainting - Various standard parts such as handles, oil sight glasses, keys etc. renewed - Wear parts like drive belts etc. renewed - Bellows partly renewed - V-guides adjusted - and much more... Delivery time: immediately year of manufacture: 1989 Machine No. 2102-xxxx Table: rigid angle table travels: X300mm/Y160mm/Z340mm quill stroke: 60mm Connected power: 1,9KW number of spindle speed: 16 Speed range: 40-2000 rpm Njdpfxspy Eldo Afrsli Dlp00n tool holder: SK40 feed rate: stepless 5-500 mm/min rapid traverse: 1200mm/min Equipment and accessories: coolant system, central lubrication, manual, machine feet Our service promise to you: - We are a certified master company in the field of mechanical engineering - All machines are thoroughly checked - All lubricants and possibly worn parts are exchanged in advance - On request, we overhaul the selected machine completely or in part - If desired, they can order additional accessories such as tools, etc. directly with - On request we can mount further accessories like safety devices etc. for you - Gladly we take care of the dispatch and/or the bringing in

Condition: excellent (used), Year of construction: 2018, Index G220 CNC Mill Turn Mfd. 2018 (Demonstration Machine)  Recommissioning 2021 Nodpfx Asw Tfanefrsli Control: Siemens 840D Solution Line, few production hours Main spindle D90 Counter spindle D90 Clamping pressure device 8 to 80 bar Upper tool carrier with motor milling spindle HSK-T63 Axes X, Z, Y and B Tool carrier 2 with X, Y, Z-axis and turret head with 12 stations VDI30 Tool changer with chain magazine double-row HSK holder 2 x 50 HSK 63 Tool management type "Milling machine" with relative D-number Cooling unit Automatic work door Light barrier for drill breakage control 5-axis simultaneous machining for motor milling spindle Motor current-based tool monitoring system Management of tools with setup dialog (max. 250 tools) Workpiece measuring on main or counter spindle Measuring cycles Follow-up center for cross slide 2 Tailstock function in the counter spindle Electronic shaft Grinding cycles Chip conveyor Filter Coolant system ECO-Fluid 3 pumps 3, 8, 20-80 bar UNIMAG4 Portal removal device Transport belt No clamping devices, no tool holders, ex location

Condition: good (used), Year of construction: 2001, Good, used condition. Few operating hours (1675 hrs). Motor: 11 kW. Throughput up to a maximum of 220 kg/h. Briquettes: 150x60 mm. Press dimensions: approx. 2200x3000x1920 mm (LxWxH). Nsdpfx Aowcc D Rsfreli Control cabinet dimensions: 500x1250x2120 mm (LxWxH). Weight approx. 3000 kg.

Condition: good (used), Technical specifications: Briquetting press in good condition Year of manufacture: 2007 Nodpfx Afewtdk Toreli Technically inspected in 06 / 2025 Cylindrical briquette: 80 mm Throughput up to max. 150 kg/h *only approx. 3,949 operating hours - Hydraulic press: briquetting press with discharge chute - Hydraulic unit: 4 kW - Pressure: max. 300 bar - Transport dimensions: 1585/2140/H1940 mm - Weight: 1,370 kg Functional guarantee upon handover We are happy to arrange a free test run!

Condition: as good as new (ex-display), Year of construction: 2022, functionality: fully functional, controller manufacturer: Beckhoff, Spindle Speed: 60,000 rpm Spindle power: 0.625 kW Torque: 10 Nm Tool holder: HSK-EZ15 Nljdpfevyp Ewex Afroi Number of tools: 60 Working area Travel X: 78 mm Travel Y: 56 mm Travel Z: 50 mm B-axis: -110° to +110° C-axis: 400 rpm Chip-to-chip time: 3.5 sec Rapid traverse: X/Y/Z 30/30/30 m/min Workpiece changing device Technology: Zero-point clamping system Workpiece changing time: 10 sec Max. table load: 10 kg Accessories Chip management: Chip trolley Coolant management: Coolant system Workpiece measurement: Renishaw measuring probe – RMP24-micro Tool measurement: tool length measurement / breakage Other: Automation Feed 5

Condition: new, Year of construction: 2025, functionality: fully functional, General Control: Siemens 828 D Turning diameter: 400 mm Turning length: 560 mm Swing diameter: 690 mm Bar capacity: 81 mm Rapid traverse speed: 30 / 10 / 30 m/min Main spindle Bar capacity: 81 mm Chuck size: 250 mm Speed: 3,500 rpm Spindle power: 25.5 kW Spindle torque: 424 Nm Counter spindle Speed: 5,000 rpm Spindle power: 10.5 kW Spindle torque: 90 Nm Tool turret Technology: 12 stations Nsdpfx Aswlf U Dofreli Tool drive: 5,000 rpm Power: 5.6 kW Torque: 53.4 Nm Tool holder: BMT-65 / BH X travel: 240 mm Z travel: 120 mm Y travel: 60 mm Equipment Chip disposal: Chip conveyor Coolant supply: Extended 140 liters Tool measurement: Measuring arm in the work area Parts management: Pneumatic part pusher Parts removal: Part catcher Bar magazine: Prepared

Condition: new, Step By Step Wet Painting Systems Elboy Industrial Solutions designs and manufactures full range of paint shops for your product. Nlsdpfx Asdy Dw Aefrei With ELBOY, you can navigate through your facility with virtual reality in the design phase, enabling you to make the desired changes in the design phase and not to encounter the surprise results. It provides designing and manufacturing services for your application by paying special attention to environmental pollution and work safety issues for the processes of Sandblasting, Putty, Washing, Undercoat and Finishing Coat for all sizes of products. Step by Step are systems with overhead conveyor or floor conveyors which can be designed for all sizes of product. Booths of Sandblasting, Chemical Washing, Pre-coat, Drying, Putty , Top Coat and Baking can be integrated into the system. In order to respectively carry out the processes determined by the system step by step, the automatic doors are opened at the end of the time period and the product automatically proceeds to the next process line. These fully automated systems are controlled via a 15” touch screen and provide various reporting methods such as main computer monitoring, product reporting and score reporting upon the demand and provide remote control. These are the paint shops where your product is designed and manufactured by our engineers in line with your capacity, use area and other demands. Maximum efficiency is aimed to be provided with minimum staff and the least space usage at electrostatic powder coating or wet paint, sandblasting, varnishing, coating, washing and similar system requirements.