Component

Heidenhain ST 3007 Messtaster .: 375135-01 !

Condition: used, Wig welding machine L-TEC, Inverter TIG 200 DC type WIG welding machine for direct current DC Serial no. 184548, year of manufacture approx. 1994 Power: 200 Amps = 60% duty cycle 155 Amps = 100% duty cycle Adjustment range: stepless Current type: DC (direct current) Mains connection: 400 Volts, 50 Hz, 32 Amps plug - 4 meter hose set with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator Ledpfxodzqb Eo Abzehl - DC only - HF ignition Space requirement L x W x H: 850 x 480 x 740 mm Weight: approx. 150 kg The welding test yields very good results when welding stainless steel with direct current. Otherwise in good condition.

Year of construction: 1972, condition: ready for operation (used), Spindle-to-table distance min./max.: 81mm/481mm, counter support spindle center distance: 195mm, spindle head swivel: 360°, milling spindle diameter: 70mm, spindle adjustment: 100mm, headstock adjustment: 300mm, table dimensions X/Y: 480mm/820mm, travel X/Y/Z: 500mm/200mm/400mm, max. workpiece length: 400mm, spindle speed: 1600rpm, feed X/Y: 500mm/min, feed Z: 250mm/min, spindle head swivel: +/-30°, machine dimensions X/Y/Z: approx. 1600mm/2550mm/1700mm, weight: approx. 2300kg. The machine was electrically tested at the end of 2025 and a defect of the emergency stop switch was discovered. Documentation available. On-site inspection is possible. Lhsdpfsx S Rcmox Abzjl

Condition: refurbished (used), Year of construction: 1990, functionality: fully functional, feed length X-axis: 1,400 mm, feed length Y-axis: 630 mm, feed length Z-axis: 500 mm, travel distance X-axis: 1,800 mm, travel distance Y-axis: 1,800 mm, travel distance Z-axis: 450 mm, spindle speed (max.): 1,800 rpm, spindle speed (min.): 1,800 rpm, quill travel distance: 100 mm, rapid traverse X-axis: 4 m/min, rapid traverse Y-axis: 4 m/min, rapid traverse Z-axis: 1 m/min, total height: 2,500 mm, total width: 3,350 mm, total length: 3,060 mm, table width: 630 mm, table length: 1,800 mm, position of the milling head: VERTIKÁLNÍ/HORIZONTÁLNÍ, type of input current: three-phase, table load: 1,500 kg, overall weight: 6,500 kg, FGS 50/63 - TOS KUŘIM Knee-Type Milling Machine Horizontal/Vertical Axis Milling New Electrical Cabinet + Push-Button Panel Lsdpfxsxpugnj Abzehl Digital Axis Readout System Completely Overhauled in 2025 Warranty: 12 months Availability: Immediately in stock CONDITION OF A NEW MACHINE – FULL REBUILD WITH GEOMETRIC ACCURACY PER MANUFACTURER SPECIFICATION FGS 50/63 – Technical Specifications: Basic machine data: Manufacturer: TOS Kuřim Overall length: 3,060 mm Overall width: 3,350 mm Overall height: 2,500 mm Total weight: 6,500 kg Total power input: 23 kVA Working range: Longitudinal travel X-axis: 1,400 mm Transverse travel Y-axis: 630 mm Vertical travel Z-axis: 500 mm Working spindle: Spindle taper: ISO 50 Number of speeds / speed range: 18 / 35.5 – 1,800 rpm Spindle motor power: 15 kW Max. spindle torque: 2,500 Nm Feed range X – Y / Z: Number of steps / range: 16/ 10 – 1,800/ 2.5 – 450 mm/min Rapid traverse: 4,000/1,000 mm/min Table: Table area (width x length): 630 x 1,800 mm Max. table load (along axis): 1,500 kg

Year of construction: 1990, condition: used, 2. Tool turret heads, manufacturer DUPLOMATIC, year of manufacture approx. 1990, type: BSV-N250 8/20-110/50. Tool holder size VDI50. Tool stations: 8. Lsdpobaf Spefx Abzohl Center height: 125 mm. Price per piece.

Condition: ready for operation (used), Year of construction: 2010, operating hours: 23,905 h, functionality: fully functional, clamping force: 600 kN, screw diameter: 35 mm, displacement volume: 135 cm³, injection pressure: 2,221 bar, opening stroke: 335 mm, total length: 2,420 mm, total width: 1,700 mm, total height: 3,100 mm, overall weight: 6,700 kg, Equipment: documentation/manual, For sale: Well-maintained injection moulding machine ENGEL INSERT 200V/60 with only 23,905 operating hours. The machine was used exclusively for sampling purposes. Inspection under power possible at any time! Lhsdpjy Iwlaefx Abzsl Technical specifications as per the pictures! Machine is immediately available!

Condition: used, Thread Rolling Machine, Cold Rolling Machine, Thread Rolling Machine, Profile Rolling Machine Manufacturer: PEE-WEE Model: UPW 24 Serial No.: P07 Year of manufacture: 2007 Maximum rolling force: 24 tons Maximum tool diameter: 270 mm Roll spindle diameter: 69.85 mm Tool bore diameter: 70 mm (nominal diameter) Maximum tool/reception length: 180 mm Maximum workpiece diameter: 50 mm Hydraulic motor power: 3 kW Lhsdpjuz If Nsfx Abzjl Roll drive motor power: approx. 5.5 kW Electrical connection: 400 Volt, 50 Hz, 10 kW - Pivotable roll spindle for through-feed thread rolling - Roll spindle speed adjustable in 4 steps via gearbox shift - Hydraulic unit integrated in the machine base - Operating manual with electrical schematic Space requirements (L x W x H): 2,000 x 1,450 x 1,900 mm Weight: approx. 3 tons Very good condition Plunge Rolling: The thread rolling tools, having the same pitch as the workpiece, form the thread by penetrating the workpiece up to the nominal diameter. The maximum thread length is limited to the width of the rolling dies. Through-feed Rolling: Used when the thread length is greater than the width of the rolling dies. Through-feed tools are divided into three sections – entry, calibration, and exit. Knurling rolls have no pitch and are swiveled at the lead angle corresponding to that of the profile to be rolled. Lead angle rolls differ from knurling rolls by having a pitch in the profile. The sum of the lead angle and swivel angle results in the effective lead angle in the workpiece.

Year of construction: 2005, condition: ready for operation (used), A lathe (Universal Turning Solution) is offered, control: Fanuc, tool turret: 12-station, tailstock, 3-jaw chuck. Tool setting arm: Renishaw HPRA. Inspection is possible by arrangement. Ljdpex I Rpxofx Abzshl

Condition: ready for operation (used), Selling a well-maintained Mikron VC 1000 milling machine due to the purchase of a new machine. Lhsdpfx Ash Tnpxebzsl

Condition: repair required (used), turning length: 400 mm, spindle bore: 75 mm, spindle speed (max.): 3,800 rpm, General information about the machine We are offering a used lathe from the manufacturer Okuma. The machine is offered as a spare parts carrier. The machine is running but not all functions can be guaranteed. The keys for operation are missing. The machine is in our warehouse and can be inspected under power Technical data Lhodpfsugmzkex Abzel - CNC control: OSP 5000L-G CNC system (German) - Tool turret: 12 positions - Lathe chuck: 250 mm - Spindle: 70-3800 rpm (11 kW, 30 min; 7.5 kW - continuous operation) - Spindle bore diameter: 75 mm - X-axis travel: 400 x 0.001 mm - Z-axis travel: 500 x 0.001 mm - Cutting speed XZ: 0.01-1000 mm / U - Rapid traverse up to: 12,000 mm / min. - Power supply: 380V - Rated power of the machine: 21 kVA - Maximum load current: 36A - Machine dimensions (width x depth x height): 3.9 m (with chip conveyor) x 1.8 x 1.8 m - Machine weight: 4500 kg

Condition: used, Grinding wheel dimensions (od x id x width) Ø 650 x Ø 304.8 x 500mm Min/max diameter to be ground 3 / 200 mm Lhodpfjix N Enox Abzjl Width of regulating wheel 500 mm Number of regulating wheel speeds Infinite Min/max speed of regulating wheel (r.p.m.) 10 / 255 r.p.m. Diamond dressing (auto/manual) Automatic longitudinal, manual penetration for both wheels Diamond dressing speed 255 r.p.m. Number of CNC axes 1 Regulating wheel dimensions (od x id x width) Ø 350 x Ø 203.2 x 500mm Width of grinding wheel 500 mm Maximum length to be ground in plunge grinding 500 mm Power of grinding wheel head motor 55 Kw Power of hydraulic motor 3 Kw Total power 60 Kw Voltage 220/380V Length 2,300 mm Width 2,800 mm Height 2,100 mm Weight 15,000 Kg