Veneer saw w. planing unit

Höfer FSP 310

Condition: excellent (used), functionality: fully functional, Weinig Powermat 500 four-sided planer Working width 230mm Working height 160mm Number of spindles 6 Spindle arrangement: Bottom 5.5kw 8000r.p.m Right 5.5kw 8000r.p.m Left 7.5kw 8000r.p.m Isdpfx Ahovfr Rgsbjih Top 7.5kw 8000r.p.m Bottom 7.5kw 8000r.p.m Universal 5.5kw 8000r.p.m Spindle #6 equipped with power lock system Feed speed adjustable by inverter up to 30m/min Pulling rollers in the worktop (1 grooved roller for wet wood) Electro-motorized positioning of height and working width Pneumatic material stops Drive on karda shafts Total power 41kw Year of production 2005 CE certificate

Condition: excellent (used), total length: 3,000 mm, total width: 1,500 mm, Panel press in very good working condition + Grecon finger jointing Isdpfx Ajt Uduxshbsih

Condition: used, machine/vehicle number: 007984, Max. machining width: 1300 mm Ijdpfxewqdbme Ahbjih Min. machining thickness: 4 mm Working Table: Fixed pass height Vacuum feed belt: yes No. Operating units: 4 Nr

Condition: refurbished (used), functionality: fully functional, year of last overhaul: 2025, 1) Log Yard with 10 Boxes (Drop Boxes) – New and Used Log Feed and Sorting Line New Feed rate 50 m/min. as well as the following used components: Comprising: New cross feed conveyor, step feeder Used log transfer carriage, Used log transfer carriage with ejector, Used Cambio 50 debarker, Used split detection unit with belt, Measuring section, sorting log carriage. Including debarking; Inspection and Painting; including log infeed. Without boxes, sheet metal cladding, measuring system, discharge control, or control cabinet. Root reduction. 2) Log Infeed for Canter Line Heavy-duty cross log conveyor NEW Cross log conveyor in 4-strand execution Axle spacing: 7.5 m Total length: 8.0 m Drive shaft: 100 mm diameter Chain: Bush conveyor chain, pitch 100 mm – heaviest version Fixed rear stops, without sheet metal cladding Steel substructure: HEB 200 Construction height: 1000 mm Drive: geared motor 7.5 kW 3) Equalizer NEW Number of chains: 4 Axle spacing [mm]: 3500 Overall width [mm]: 5730 Paddle spacing [mm]: 1000 Drive shaft diameter [mm]: 100 Drive SEW [kW]: 7.5 Speed [m/min]: 10 Design: completely sheet metal covered between chain runs 4) Step Feeder NEW Feed steps: 4 Overall width [mm]: 4200 Plate thicknesses [mm]: moving steps 12 mm, fixed steps 20 mm Drive SEW [kW]: 18.5 Drive via crank mechanism and geared motor 5) Canter Line (WD brand) Log transfer carriage before RB 2 infeed Length extension to 18.5 m – drive and deflection RB 2 infeed with powered steel chain bed, designed for lateral log infeed. Conveyor chain with carrier dogs, frame in welded construction. Intake and centering unit ZE with log rotation unit TDV and centering device. Feeding unit ZE Log length: 2.5 – 5 m Clear width: min. 80 mm Clear width max.: 780 mm Construction height: 1000 mm Weight: 5400 kg Profile canter FZ 3 Machine frame with base frame 2 knife head housings with main shaft bearing, 2 knife heads with finishing segments, Iiodpfxjykr Aqs Ahbeh Drive power 90 kW Log diameter: min. 100 mm, max. 400 mm Chipping height above the chain max. 515 mm Distance between disks max. 570 mm Distance between disks min. 60 mm Disk diameter: 1260 mm Positioning via electric motors 2 hydraulic units 35 kW hydraulic pre- and post-cut Pre-cut square timber turning device Electrically powered roller conveyor TR 800 Centering and feeding unit ZE with FZ 3 canter

Condition: excellent (used), Year of construction: 2003, machine/vehicle number: 0-241-06-5232, functionality: fully functional, operating hours: 12,608 h, cutting height (max.): 125 mm, cutting width (max.): 2,200 mm, cutting length (max.): 4,300 mm, Panel Saw Holzma HKL11/43/22 Max. cutting width: 4300 mm Max. cutting length: 2200 mm Max. cutting height: 125 mm The saw is in continuous operation, so viewing during operation is possible. The machine will be available from 02/03/2026. Iodpfx Ajxfvp Ashbsih

Condition: new, Year of construction: 2024, New machine Iodpfew Naanjx Ahbjih Year of manufacture: 2024 MACHINE SEEKER ENQUIRIES: Please understand that we do not offer this new machine outside our sales area in Germany (Rhine-Main area and North Rhine-Westphalia). These inquiries will not be answered. MACHINESEEKER ENQUIRIES: Please understand that we do not offer this new machine outside our sales area in Germany (Rhine-Main area and North Rhine-Westphalia). These inquiries will not be answered. Equipment and technical specifications: The Master brings grinding to the point. It embodies the essence of our 75 years of experience in grinding technology. This means that it combines all the features essential for the fast, reliable production of perfect surfaces right out of the box. Nothing more, nothing less. The core model, the Kündig Master, is equipped with a calibration roller and a sanding pad unit and features a proven design that guarantees decades of high sanding precision – and all this across the generous working width of 1350 mm. A control unit is also on board, which quickly and easily achieves the desired result. The Sanding Units – Proven Combination The sanding units rely on the proven combination of calibration roller and sanding pad. For secure workpiece guidance, a parallel spring-loaded steel pressure roller is located at the machine inlet, and rubber pressure rollers are located between the sanding units. Calibration Unit (R): The calibration unit is a grooved rubber contact roller of proven hardness. It is ideally suited for calibration tasks, even with high chip removal rates if necessary. The level of the contact roller is continuously adjustable to compensate for the thickness of the abrasive grain. Segmented sanding pad (E): With the E-Plus configuration, the fine sanding unit features a segmented, electronically controlled sanding pad with a scanning width of 35 mm instead of the pneumatic version. This allows for even more precise fine sanding in the edge area of the workpieces. The edge pressure of the sanding segments is automatically controlled, but can also be precisely adjusted on the touchscreen to more precisely influence the sanding around the workpiece edges. Changing the graphite sliding coating is also quick and easy. The features - In a nutshell Construction: In terms of robustness and durability, the Master is in no way inferior to our other model series. It features the same solid construction that makes all our machines a forward-looking investment and is designed to deliver precise sanding results even after many years. Top adjustment: For over three decades, we have equipped our machines exclusively with top adjustment. Why? While more complex in design than table adjustment, it is also superior in many respects. The machine can handle heavier workpieces, maintains its precision more reliably, and offers the advantage of a constant working height. Workpiece dimensions: The upper section, i.e., the through-hole, is motorized and can be finely adjusted via a touchscreen. The maximum through-hole height is 160 mm. With a working width of 1350 mm, the Kündig Master offers a generous, tried-and-tested standard size.

Condition: reconditioned (used), functionality: fully functional, The Lamina FA Blackline 1620BL is a highly accurate, high speed sheet-to-sheet fully automatic laminating/mounting machine. The machine can handle most of the existing materials in the market. The modular construction allows easy upgrading and maintainance resulting in a machine that lasts for many years. Max. sheet size: width: 1600 mm length: 2000 mm Min. sheet size: width: 350 mm length: 350 mm Feeder Capacity: Top feeder: 500 mm (20”) Bottom feeder: 800 mm (32”) Top Sheet: 130 to 450 g/m2 1 pts = 28,25 g/m2 Bottom Sheet: From 250 g/m2 to 10 mm (0,39”) 1 pts = 28,25 g/m2 corrugated from 0,6 - 10 mm (0,016” - 0,39”) Air Requirements: 6 bar; 80 psi; 34 CFM, Approximately 500 L/min Can be additionally equipped with Optional Laminating Machine PB 1600 Pressure Belt Iijdpfx Ahsw Hrrrsbjh

Condition: new, Year of construction: 2024, Working width: 600 mm Working height: 5 mm to 300 mm Minimum workpiece length: 250 mm Units: 2 1. Saw cutting unit Random System: Saw cut appearance 2. Brush: Tynex, diameter 210 mm Height adjustment: electric Height display: digital Feed speed: 4 - 14 m/min Iedpfx Aoupy Spehboih Motor power saw unit: 1.1 kW Motor power brush: 4 kW Motor power feed: 0.37 kW Machine length: 1400 mm Machine width: 1500 mm Machine height: 1600 mm Weight: 700 kg

Condition: new, Year of construction: 2024, functionality: fully functional, power: 5 kW (6.80 HP), cutting height (max.): 200 mm, cutting width (max.): 1,300 mm, saw blade diameter: 550 mm, cutting length (max.): 3,200 mm, cutting width at rip fence: 1,300 mm, sliding table length: 3,200 mm, Exhibition machine F 45 Elmo Drive - Swivel + / - 45 ° - Cutting height 200 mm - Preparation for scoring unit no. M24038 - Double roller carriage with 3200 mm - Angular mitre fence 3200 mm Digit L - CNC rip fence 1300 mm - Duplex mitre fence 1350 mm manual Iijdpfx Ahjuh R R Eobsh - Template holder - On/Off switch on the double roller carriage - Front support roller

Condition: excellent (used), Year of construction: 1985, still very nice veneer saw with planing head cutting length 3050 mm Iiodpon An A Tjfx Ahbsh with rear support and fence