Surface Grinding Machine - Horizontal

ELB-Schliff SWBE 06 NPC-K

Year of construction: 2020, condition: as good as new (ex-display), electrode diameter 0,5 to 3mm travels 300x400x350mm ) CE-cretification verifies the best possible safty all Machines in over-floor construction Elektrode Ø 0,5-3mm Travel X-Axis 300mm Hedpfx Apef Hmn Asdew Travel Y-Axis 400mm Travel Z-Axis 350mm Travel W-Axis 300mm Speed W Axis 30-60mm/min Rapid feed Z-Axis 120mm/min removal rate (max.) 300:1 Table dimension 320x440mm max.generator capacity 30A

Condition: new, functionality: fully functional, machine/vehicle number: 8153336470, overall weight: 616 kg, volume flow: 399 m³/h, pressure (min.): 4 bar, pressure (max.): 13 bar, noise level: 67 dB, type of cooling: air, Equipment: documentation/manual, refrigerant dryer, type plate available, We are a company specializing in the compressed air industry for over 20 years. Professional level of service and high quality goods offered by our company - "proven" on the market - guarantee successful cooperation with you. We offer NEW screw compressor Atlas Copco GA37VSDs FF (variable speed with built-in dryer) Machine equipped with frequency converter (inverter), manufactured based on the latest technologies, which translates into greater efficiency and performance: On average 20% lower unit energy consumption (SER) than in previous models of the GA VSD series. Ecological and efficient VSD+ variable speed drive system reduces energy consumption by an average of 50% compared to models that operate at idle speed. Regardless of energy savings, efficiency (FAD) increases by up to 12%. Efficient fan motor (compliant with the ERP 2015 directive) reduces energy consumption and noise level. Hodpfjwlp Hdex Apdow Superior Motor Efficiency (iPM) up to 94.5% exceeding IE3 efficiency levels. Built to work hard for your success. The industry-leading GA Series oil-injected rotary screw compressor delivers unmatched efficiency, high productivity and low cost of ownership – even in the harshest conditions. Technical data: capacity at 4 bar: 15.69- 13.75 l/s / 0.94-7.85 m3/min capacity at 7 bar: 15.67-129.35 l/s / 0.94-7.76 m3/min capacity at 10 bar: 15.68-110.79 l/s / 0.94-6.65 m3/min Max pressure 10 bar (13 Bar variant on request) Voltage 400 V Motor 37 kW Noise 67 dB(A) Weight 616 kg Motor with internal permanent magnets (IPM) Compression element Direct drive Innovative fan Separator/oil filter with durable construction Electronic water drain valve that does not cause compressed air losses Controller Elektronikon Inlet valve VSDs module Manufacturer code: 8153336470 If you are not sure whether the device is right for you, you have not found the right compressor, CALL! We will advise you on the right choice of device. We invite you to familiarize yourself with our full offer.

Condition: new, pressure 40 t throat 225 mm stroke 8-84 mm Table dimensions 580 x 450 mm ram adjustment 55 mm no. of strokes 130 Hub/min ram surface 185 x 180 mm ram hole 40 H7 mm hole in the table 210 x 170 mm Hedpfx Apeb U Hwtedsw T-slots 22 clamping plate 570 x 450 x 65 mm total power requirement 3,5 kW weight of the machine ca. 2,7 t dimensions of the machine ca. 1,4 x 1,1 x 2,1 m

Condition: ready for operation (used), Width: 1000 mm Length: 1500 mm Hjdpfx Aogq Nawjpdew Plate height: 195 mm Height of the feet: 600 mm Total height, working height: approx. 800 mm Weight:

Condition: used, max. wheel diameter 0-200 mm Hodpfxotuxa Uo Apdjw max. module 25 min. module 0,5

Condition: used, turning diameter over cross slide: 710 mm, spindle bore: 180 mm, turning diameter: 1,000 mm, turning length: 4,000 mm, quill stroke: 250 mm, quill diameter: 125 mm, spindle speed (max.): 800 rpm, spindle speed (min.): 6 rpm, bed width: 560 mm, overall weight: 9,700 kg, Equipment: rotational speed infinitely variable, KRAFT BV-40160 – USED HEAVY-DUTY LATHE A KRAFT BV-40160 from a company liquidation. Originally delivered to the previous owner as new from the factory in 2016/2017. On-site inspection or via video call is possible at any time. KEY FEATURES - Conventional guide and lead screw heavy-duty lathe, turning diameter 1,000 mm, distance between centers 4,000 mm - Additional guide for the tailstock on the lower machine bed - Frequency-controlled main drive 22 kW - Swiveling 4-position tool holder TECHNICAL DATA - Turning diameter over bed: 1,000 mm - Turning diameter over cross slide: 710 mm - Swing diameter in the gap: 1,280 mm, gap width 450 mm - Center height: 500 mm - Distance between centers: 4,000 mm Hedpjzi Duhefx Apdew - Bed width: 560 mm (3V + 1 flat), additional tailstock guide on the lower bed - Cross slide width: 350 mm - Spindle bore: 180 mm, spindle nose A2-15 - Spindle speeds: 4-speed, continuously variable 6-800 rpm - Main motor: 22 kW with frequency inverter - Cross movement of tailstock: 550 mm, upper slide movement: 225 mm - Tailstock quill Ø 125 mm, stroke 250 mm, taper MK 6 - Tool bit cross-section: 40 mm - Lead screw: Ø 60 mm x 2 T.P.I. - Weight: net approx. 9,000 kg / gross approx. 9,700 kg - Dimensions: approx. 5,845 x 1,950 x 1,925 mm STANDARD EQUIPMENT - Coolant system - Fixed steady rest Ø 60-380 mm - Swiveling, manual 4-position tool holder - Sliding chuck guard with electrical interlock - Swiveling, electrically interlocked guard for the upper tailstock - Traveling, rear chip / splash water guard - Halogen machine lamp - Installation / leveling elements, machine tools - German and English technical documentation, CE version - 400 V, 50 Hz, 3-phase CONDITION Used machine from a company liquidation. Sold "as is, where is", no warranty. On-site inspection or via video call is strongly recommended. OUR SERVICE Online or on-site factory inspection, transport organized on request, assembly, commissioning and operator training by our service technicians, direct German-speaking contact person for spare parts and support, member of the FDM, the trade association of the machine and tool wholesale trade. Since this is a single item, subject to prior sale. Please call or write to us, and we will arrange an inspection appointment as soon as possible.

Condition: as good as new (ex-display), PFAFF 8320 - 111/101 long-arm version with table Hodpfexa D Hrex Apdow

Condition: ready for operation (used), Year of construction: 2008, - USED - 5-AXIS BRIDGE-TYPE VERTICAL MACHINING CENTRE     X-AXIS TRAVEL: 1750 mm Y-AXIS TRAVEL: 1400 mm Z-AXIS TRAVEL: 600 mm RAPID FEEDS X-Y-Z: 35 m/min SPINDLE: 18000 rpm; 18,5-25 kW; HSK A63 TABLE SIZE: 1000 x 1200 mm MAX ADMITTED LOAD: 5000 Kg Hodpfowl R Ddox Apdew TOOL MAGAZINE: A CATENA ; 30 POS HEAD: A/B AXIS AUTOMATIC CONTROL UNIT: HEIDENHAIN iTNC 530 WEIGHT: 18000 Kg OVERALL DIMENSIONS: 6000 x 4000 x 3850 mm ACCESSORIES: SWARF CONVEYOR ; PORTABLE HANDWHEEL ; LASER TOOL SETTER

Condition: used, pressure 55 t throat 250 mm stroke 10-90 mm table-size 640 x 495 mm no. of strokes 120 Hub/min ram adjustment 55 mm ram surface 290 x 210 mm ram hole 40 H7 mm hole in the table 220 x 190 mm T-slots 22 Hjdecp Apyjpfx Apdow clamping plate 620 x 485 x 65 mm total power requirement 4,5 kW weight of the machine ca. 3,4 t dimensions of the machine ca. 1,5 x 1,2 x 2,2 m

Condition: excellent (used), Year of construction: 2015, Okuma GENOS L200E-MY CNC Lathe Technical Data Manufacturer: Okuma Model: GENOS L200E-MY Control: OSP-P300L-R Voltage: 400 V Phases: 3 P Hodpfx Apjy R A N Aodew Frequency: 50/60 Hz Connected load: 15.3 kVA Rated current: 25.6 A Short-circuit withstand capacity: 2.5 kA Max. turning diameter: Ø 200 mm Max. turning diameter x length: Ø 200 x 380 mm Swing over bed: Ø 450 mm Swing over cross slide: Ø 300 mm Workpiece weight (single-sided support): 120 kg Spindle diameter: Ø 100 mm Spindle nose: JIS A2-6 Spindle bore: Ø 66 mm Spindle speed range: stepless Spindle speed: 75 to 3000 rpm Number of tool stations: 12 Turret type: Multitasking V12 turret Tool holder, external turning tools: 20 x 20 mm Tool holder, internal turning tools: Ø 32 mm Rotating tool speed: 6000 rpm Travel (Z-axis): 400 mm Travel (X-axis): 165 mm Travel (Y-axis): 80 mm Feed range: 0.001 to 1000 mm/rev Rapid traverse Z-axis: 25000 mm/min Rapid traverse X-axis: 20000 mm/min Rapid traverse Y-axis: 10000 mm/min Tailstock quill diameter: Ø 55 mm Tailstock quill stroke: 80 mm Machine height: 2040 mm Footprint: 2120 x 1750 mm Machine weight: 4800 kg Year of manufacture: 2015 No guarantee is given for the correctness, completeness or up-to-dateness of the information provided.