Cold saw

EISELE VMS II

Condition: excellent (used), Year of construction: 1987, functionality: fully functional, Cold Circular Saw Eisele VMS-II-S, Year 1987, Very Good Condition from University >> Manufacturer: EISELE, Model VMS II S >> Vertical cold circular saw >> 2 speeds: 17/34 rpm >> Year of manufacture: 1987 >> Working range: Ø 80-102 mm / Flat 160x75/82 mm >> Drive power: 1.4/1.9 kW >> Saw blade diameter possible: 275 - 315 mm >> Space requirements approx. 80 x 90 x 180 cm Ljdpfexx T Nmsx Adkjrw >> Weight approx. 400 kg >> Manual lowering of the saw carriage with adjustable hand lever >> Manual, laterally adjustable material vice >> Coolant system with electric coolant pump integrated in machine base About the machine: A well-maintained Eisele VMS-II cold circular saw is being offered. The machine is in original condition and fully functional. It comes from a university and has seen little use. You are welcome to test and inspect the saw under power at our facility.

Condition: used, Seriennummer: 0419 Lrjdpfxjwm Rrdo Adkjw

Condition: good (used), Year of construction: 1972, functionality: fully functional, machine/vehicle number: 27252, saw blade diameter: 275 mm, cutting height (max.): 140 mm, cutting range round steel at 90°: 80 mm, total length: 680 mm, total height: 1,750 mm, total width: 680 mm, overall weight: 270 kg, type of input current: three-phase, rotational speed (min.): 10 rpm, rotational speed (max.): 80 rpm, space requirement length: 2,120 mm, input voltage: 380 V, length stop: 1,000 mm, working height: 950 mm, saw drive: 1,400 W, Equipment: documentation/manual, The machine has been in operation since it was purchased new in 1972, works perfectly, and will remain in use until sold. INCL. 6 SAW BLADES 275 x 2.5 x 2.5 x 40, freshly reground 2021: Coolant pump switch replaced 2020: Overhaul at Bider Hauser AG - Drive motor replacement - New saw blade flange - New gear oil Base area 680 x 680 mm Length stop right 1000 mm (1310 mm from saw blade) Workpiece support left 800 mm from saw blade Speeds: 10/20/40/80 rpm Cutting ranges: Hollow flat profiles / angle iron: - Straight --> 140 x 70 mm Lrsdpfxov Uk Iie Adksw - Mitered --> 100 x 70 mm Pipes --> 3" diameter Solid material --> 80 mm diameter Square material --> 50 x 50 mm

Condition: used, Max. saw blade diameter: 350 mm Manual saw feed 2 sawing speeds Lsdjxn Ivgspfx Adkorw Coolant lubrication

Year of construction: 1991, condition: good (used), machine/vehicle number: 900 1241, disk of circular saw-Ø: 275 mm cutting area at 90° round: 90 mm cutting area at 90° square: 75 x 75 mm cutting area in mitre at 45° square: 75 x 75 mm disk rotations: 40/80 upm Lrjdpfx Adsm Twgwjksw engine: 380 V, 1/1/2 kW space needed: 700 x 600 x 1580 mm weight: ca. 180 kg

Condition: used, Mitre Cold Circular Saw EISELE Type VMS-II-S Model No. 421 Serial No. V 2295 Year of manufacture: 1984 Cutting capacity at 90° (round): Ø 120 mm Cutting capacity at 90° (rectangular): 120 x 90 mm Saw blade diameter max.: 350 mm Blade speed: 40 - 80 rpm, 2-step Mitre cuts: 45° to the left, 90°, and continuously adjustable up to 30° (60°) to the right Motor power: 1.4 and 1.9 kW Power supply: 380 Volt, 50 Hz - Two cutting speed stages via two motor speeds Lrjdpfx Aexk Uunodkjw - Manual saw carriage lowering via adjustable lever - Manual material vice, side-adjustable - Coolant system with electric coolant pump integrated in machine base - Equipped with one saw blade, approx. Ø 350 mm - Outfeed roller conveyor 750 mm with simple length stop up to 1000 mm, fixed to the machine base - Infeed roller conveyor 2350 mm with simple length stop up to 2500 mm, free-standing - Usable roller width: 180 mm Space requirement of base machine with outfeed roller conveyor (L x W x H): 1400 x 850 x 1700 mm Base machine weight: approx. 450 kg Infeed roller conveyor weight: approx. 140 kg Good condition

Condition: not inspected (used), Eisele VMS II-S-PV automatic saw with automatic feeder and piece counter Lsdpfx Aswf Af Tedkorw Roller conveyors left and right Metal band saw, metal circular saw

Condition: excellent (used), Year of construction: 2004, Machine type: - Kondia B640 - Year of manufacture 2004 Control system: - Heidenhain iTNC 530 - Electronic handwheel Tool measurement: - Tool Eye - 3D probe Tool changer: Lrsdpfxsw H N R Ee Adkow - 22 magazine pockets Travel paths: - X - 600, Y - 400, Z - 510 mm Main spindle: - Max. 12,000 rpm (new main spindle in 2020) - Tool holder BT 40 Table: - Clamping surface 800 x 400 mm Coolant system: - Through-spindle coolant 20 bar - External coolant supply - Spindle cooling Accessories: - Chip conveyor - Various tool holders - Various clamping studs - Machine documentation Availability: - Immediately

Condition: good (used), Year of construction: 1985, Eisele VMS-II-S-PV metal circular saw Ljdpfjd Hbnfjx Adkorw Type No. 421 Maschnr. 01224 380V Built in 1985 50 Hz

Condition: good (used), Year of construction: 2014, Traverses; 800 x 460 x 520mm, Table size 1000 x 460mm, Lredpfju Ehi Aex Adkjw Table load 600 kgs, Spindle speed 8,000 rpm, Spindle power 11/15Kw, spindle taper BT40, 24 station ATC , Fanuc I series, coolant, swarf conveyor.