Tool cutter

DECKEL P 1

Condition: new, Year of construction: 2024, machine/vehicle number: 302340, Profile Bending machine KB Türkei model MB 30 bottom shaft 30 mm top shaft 35 mm two rollers driven with basement capacity: Hedpfx Aed S Uf Sog Isfg up to round tube 48 x 3,0 mm flat material 50x10 mm square tube 40x40x3,0 mm weight 170 kg motor 0,75 kw 400 Volt 50 Hz 3 ph.

Condition: new, empty load weight: 17,250 kg, maximum load weight: 48,700 kg, overall weight: 66,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,480 mm, loading space height: 375 mm, tire size: 245/70 R 17.5, color: grey, operation weight: 17,250 kg, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and removed hydraulically -For tractor units: 6 x 4 and 8 x 4 (or 6 x 4 with optional 1-axle dolly) Low bed: -Low bed with external supports, designed as a telescopic tank bridge in low construction with extension at the front -Length x width approx. 7,550 mm x 2,740 mm -Mechanical locking of the extension Chassis: -Chassis at the rear with closed outer frame -Checker plate covering and continuous prism excavator trough approx. 1,450/900 x 505 mm, open at the rear Axles, suspension and tires: -"PENDEL-AXLE", all axles hydromechanically forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with shut-off valves and pins for securing in raised position -Final painting of axles with 2 layers of 2-component paint in a single color in "FAY-Gray-34-0260" -Technical axle load 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 Accessories: -Steel bulkhead, plug-in, approx. 400 mm high -4 wheel chocks -Gooseneck in the rear upper area closed with a removable cover -1 pair of steel ramps with climbing strips and fastening bolts to bridge the hooks of the low bed -The ramps can be placed over or between the hooks -Fastening options for the steel ramps at the rear between the outer supports of the gooseneck -One Locking point approximately every 1,000 mm on the extension -1 lashing ring on the left and right on the front cross member -Connection strip for supply lines to the tractor unit, attached at the height of the outer frame profile -6 pairs of threaded blocks on the outside of the inner supports of the loading area for mounting screwable rings M24 -6 pairs of countersunk lashing rings on the outside of the outer supports of the loading area, foldable inwards and outwards -1 pair of threaded blocks at the front and rear of the outer supports of the loading area for mounting screwable rings M24 -Hanging strip for loose aluminum loading ramps on the vehicle's end cross member -Central lubrication system with 2 pumps, BEKAMAX brand Hfsdpsh Hm Tzjfx Ag Ieg -Steering from the front and rear, operated by cable remote control, with alignment control of the axles -3 kW electro-hydraulic unit for controlling the hydraulic processes, with the exception of hydraulic cable winches -Removable loading floor (galvanized) in 3 elements can be inserted between the outer supports with hardwood flooring -Foldable extensions, by approx. 230 mm per side -Extension planks, loose, framed in steel -4 warning signs approx. 423 x 423 mm -Radio remote control for operating the steering -3.5" king pin -Anti-slip sticker on the left bevel of the gooseneck -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw couplings -Guide plate from the gooseneck for the fifth wheel plate, approx. 800 mm wide -1 spare wheel with mounting adapter -Parking position on the gooseneck for the warning signs when not in use -2 pairs of stake pockets embedded in the outer frame of the chassis, for plug-in stakes approx. 100 x 50 mm -Dipper handle recess of the rear chassis closed at the back with a plug-in plate -Color of the trailer MB 7350 Novagrau

Condition: new, Year of construction: 2026, UNIBOHRFIX 100 H Fully automatic drilling machine, measuring length 6000mm Item No. 6020 With the fully automatic drilling machine UniBohrFix 100, your material is positioned on the X-axis at the desired position, clamped and drilled. All you have to do is press the start button. Round tubes, rectangular tubes and angle profiles, as well as flat and solid materials, can be conveniently pneumatically clamped in the horizontal gripper of the positioning system. After simply entering the X values ​​and calling up a program that has already been written, the machine works completely independently. The Y-axis can be adjusted by the operator using a handwheel with a digital display. Advantages • A sequence of holes is automatically executed at precise intervals. • Potential operator errors are drastically reduced. • Programming takes just a few minutes. • Very good value for money. • Significant reduction in labor force Fully automatic execution Measuring length: 6,000 mm Total length: 13,500mm NC 1-axis control Pneumatic vice (span 200 mm) Minimum quantity spray unit with holder and spray nozzle Drill: Unimax 3T AV (for technical data see data sheet) anti-rotation device motorized height adjustment tapping device NC positioning system PD 200p Feed force 200 kg Hfedpfxefu Itbj Ag Isg Positioning according to absolute and incremental dimensions possible Carriage with DC servo motor and encoder Trolley with 12 ball bearings Pneumatic stop clamping with high holding power Steel guide rail with precision toothed rack Steel carrier profile to protect against dirt Infeed and outfeed material roller conveyor RD-200/4 Length: 6,000 mm / 7,000 mm / load capacity 200 kg/m / rollers adjustable in height / mounting bracket / roller width 407 mm / insert plates / struts / roller diameter 50 mm / steel rollers

Condition: used, Technical specifications: X-axis travel: 700 mm Spindle speed: up to 1500 rpm Feed rate: 12 - 1000 mm/min Table size: 1100 x 250 mm Hsdpsxtnn Tofx Ag Iefg Swiveling head: yes Dimensions, approx.: 1750 x 1600 x 1850 mm Weight, approx.: 1900 kg

Year of construction: 2026, condition: new, IWR 2000D - The fruit washer with mill for fruits and vegetables is made entirely of high-quality stainless steel and is equipped with a sorting grate, a washing tank, and a conveyor belt. The fruits are immersed in water and, after pre-washing, transported via the conveyor belt where they are thoroughly cleaned with fresh water. Afterwards, the cleaned fruits enter the mill, where they are processed to the desired mash consistency using the selected sieve. The washing system is also equipped with a dosing attachment for pack presses. Technical Information • Nominal capacity: 1500 kg/h • Power requirement: 3 kW, 400 V, 16 A • Material: WNr. 1.4301, AISI 304 stainless steel • Washing tank water capacity: 120 L per batch • Water consumption: 12 L/min • Water connection: 3/4” quick coupling • Electric control cabinet with IP65 protection rating • Swiveling Rätz mill Hfjdpfx Agetu Ikco Ieg • Equipped with rollable wheels • Easy to clean • Through the frequency converter, the conveyor capacity can be easily adjusted Dimensions: Length: 3250 mm Width: 840 mm Height: 2270 mm Weight: 160 kg

Condition: used, Year of construction: 1985, x-travel 485 mm Hsdpfx Astqqlljg Iofg y-travel 385 mm z-travel 380 mm table surface area 800 x 460 mm spindle taper SK 40 control CONTOUR 1 spindle turning speed range 50 - 2500 U/min feeds 10 - 1000 mm/min rapid traverse 2 m/min table load capacity 600 kg quill stroke 80 mm total power requirement 7,5 kW weight of the machine ca. 2,0 t dimensions 2,4 x 1,7 x 1,98 m Acc.: vertical head with hydr. tool clamping and quill retraction, solid table, coolant - movement of X/Y/Z also possible via handwheels -

Condition: good (used), Year of construction: 1962, High speed radial drilling machine, radial drilling machine, drilling machine, boom drilling machine, high speed radial drilling machine -Clamping table: 400 x 1100 mm -Projection: 930 mm -Taper mount: MK4 -Engine power: 1.35/1.8 kW -Speed: 41-1700 rpm -Columns: Ø 200 mm -Spindle stroke: 125 mm Hfedpfxsirax Uj Ag Iog -Thread cutting device: YES -Feed: 0.075 - 0.3 mm/rev -Dimensions: 1800/1235/H2240 mm -Weight: 1500kg

Condition: ready for operation (used), machine/vehicle number: 5722, table mounting size: 190 x 710 mm table movement x: 390/360 mm Hfjdoflrg Topfx Ag Ijg table movement y: 150 mm table movement z: 280 mm spindle taper: SK 40 spindle turning speed range: 100 - 3100 rpm carriages longitudinal: 0 - 600 mm/min electrical connection: 380 V, ca. 1,5 kW space needed: 1400 x 1200 x 1500 mm weight: ca. 680 kg

Condition: good (used), Year of construction: 1997, functionality: fully functional, feed length X-axis: 450 mm, feed length Y-axis: 300 mm, feed length Z-axis: 350 mm, 3-axes digital read out horizontal and vertical milling spindle quill Technische Daten / technical details: Längsweg X / X-travel longitudinal 450 mm Querweg Y / Y-travel cross 300 mm Senkrechtweg Z / Z-travel vertical 350 mm Tischgröße / table size 800x400 mm Spindelaufnahme / spindle taper SK40 Drehzahlbereich / spindle speed 50-2500 UpM /rpm Hfsdowyit Hopfx Ag Ijg Vorschubbereich / feed range 8-400 mm/min. Antriebsleistung / power capacity 3,2 kW Gewicht der Maschine / weight 1500 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: good (used), Year of construction: 2000, turning diameter 340 mm turning length 2000 mm control FAGOR 8055 swing diameter 550 mm spindle bore 108 mm spindle turning speed - stepless 2500 U/min power capacity 16.5 kW quill stroke 220 mm diameter of quill 100 mm total power requirement 19 kW weight of the machine ca. 4300 kg Hodpfsvwgpbjx Ag Ijfg dimensions of the machine ca. 4300 x 1600 x 1800 m This EMCO E 300x2000 cycle lathe is supplied complete with all accessories. Description: - Coolant device - 1 piece Luenette open 20-145mm - 1 piece closed guide 15-185mm - 1 piece face plate - 1 piece three-jaw chuck - 1 piece wedge bar chuck D=400mm - Parat 4-fold tool holder - Various tool holders