Road guardrail production line

Chengxing Machinery

Condition: used, Year of construction: 2012, power: 264 kW (358.94 HP), Stationary shredder M&J 4000S. Electric drive: 2x 132 kW 400 V AC, 50 Hz Incl. substructure Incl. hydraulic unit, control cabinet inside of the container Ledpfou Dkf Dex Aagjrh

Condition: like new (used), Year of construction: 2021, operating hours: 620 h, functionality: fully functional, Kaeser Aircenter SM13-11 screw compressor (2021) Manufacturer: Kaeser Type: Aircenter SM13-11 Year of manufacture: 2021 Condition: Very good, used Switch-on hours: 1356h Load hours: 606h Maintenance in 2825h Technical data Pressure 11 bar Effective delivery quantity 1.08 m³/min Nominal power drive motor 7.5 kW Protection class drive motor IP 54 Electrical supply 400 V / 3 Ph / 50 Hz Dimensions (WxDxH) 630x1200x1716 mm Weight 400 kg Compressed air tank 270 l Compressed air connection G 3/4 Sound pressure level 64 dB(A) Lredpoxnnd Refx Aagsh Refrigeration dryer Power consumption 0.26 kW Pressure dew point 3 °C Pressure loss 0.2 bar Refrigerant R 134a Energy saving control Yes Electronic condensate drain Eco-Drain Electrical equipment EN 60204-1 Yes Scope of delivery: – Complete original documentation – RFID cards (2x) – 5m supply cable with 32A plug

Condition: refurbished (used), SCHLATTER Welded wire mesh production line MG24 Full revamped WORKING RANGE Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Adjustable by cutting device (0-1) Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24 WELDING MESH MACHINE MG 24.1/8C, Basic equipment including: - 1 Machine frame - 1 Upper support for press reception, continuously adjustable by hand crank - 1 Magnet supports with retaining magnets and weft wire monitoring. - 1 Row of pneumatic solenoid valves for press actuation. - 1 Installation for air and water. - 2 Pneumatic rotary drives with oil damping - Static motor torque with 5 bar compressed air: 480 Nm - Front continuously adjustable from: 25 - 250 mm adjustable by cutting device (0-1) - 1 Advance carriage with panel lifting device - 1 Set of tools for machine adjustment WELDING SECTION 8 Type C Transformers Rated power of each transformer: 100 kVA No-load secondary voltage: 7.1 V Rated secondary current: 14 kA 8 Thyristor contactors ES 130 12 Welding presses: 5.0 kN 12 Chain current bridge for spacing of warp wires: 50-100 mm 12 Chain current bridge for spacing of warp wires (for offset warp wires): 100 mm 10 Chain current bridge for spacing of warp wires: 100-150 mm Ledpewu Tu Defx Aagorh 8 Chain current bridge for spacing of warp wires (for offset warp wires): 150 mm 6 Chain current bridge for spacing of warp wires: 150 - 200 mm 6 Chain current bridge for spacing of warp wires (for offset warp wires): 200 mm 24 Lower electrode holders Cu with standard angled electrodes and each with a water-cooled current cable, width: 58 mm 24 Wire clamping pliers Panel width: max. 2500 mm Weft wire length: min. 900 mm Weft wire length with QF5 dispenser: min. 300 - 1600 mm Spacing between extreme warp wires: max. 2400 mm Mesh length (warp wire length): max. 2500 - 6000 mm Spacing between warp wires: min. 100 mm Spacing between weft wires: 25-250 mm Warp wire diameter: 4.0 - 12.0 mm Weft wire diameter: 4.0 - 12.0 mm Number of warp wires: max. 24

Condition: new, Year of construction: 2024, A vineyard post roll forming machine is used for vineyards and orchards to produce the stakes and posts. Normally, grape posts are 1.5-2mm thickness. The production line consists of Decoiler, Servo Feeder Straightener, Press, Stamping Tool, Roll Form Machine and Shear. Lrodot Tcz Uspfx Aagsh

Condition: new, functionality: fully functional, power: 15 kW (20.39 HP), gearing type: hydrostat, color: yellow, overall weight: 2,000 kg, empty load weight: 2,200 kg, operation weight: 2,200 kg, tire condition: 100 %, drive condition: 100 %, chain condition: 100 %, Year of construction: 2026, machine/vehicle number: 2000, Equipment: additional headlights, cabin, GT2000 The GT2000 crawler excavator is a robust and versatile machine weighing 2,200 kg, ideally suited for earthworks, construction, and installation projects. Thanks to its stable construction and precise hydraulic system, it delivers excellent performance on large construction sites as well as in confined spaces. Engine and Drive The machine is powered by a reliable Yanmar 3TNV80F engine delivering 15.2 kW, ensuring fuel-efficient operation, long service life, and consistent performance. The excavator can also operate on slopes of up to 35°. Lrsdpsqv E S Refx Aagjh Hydraulic System The hydraulic system operates at a pressure of 18 MPa, guaranteeing precise and efficient work movements. The bucket digging force is 14 kN and the arm force is 10 kN, enabling fast and effective excavation in various soil conditions. Operating Parameters The GT2000 can dig to a maximum depth of 2,050 mm, a vertical depth of 1,955 mm, and has a dumping height of 2,385 mm. The maximum working range is 3,860 mm and the minimum digging height is 3,365 mm. Rotation and Maneuverability The superstructure rotation speed is 10–12 rpm, ensuring efficient and fast work cycles. Both the minimum turning radius and the rear swing radius are 1,125 mm, facilitating maneuvering in tight spaces. Undercarriage and Stability The crawler undercarriage is 820 mm wide with a minimum ground clearance of 210 mm, providing stability. The ground clearance of the dozer blade is 230 mm and its maximum digging depth is 275 mm, supporting safe operation on uneven terrain. Swing Arm and Cabin The swing arm can rotate 75° to the left and 45° to the right, enhancing operational versatility. The cabin height is 2,270 mm, offering the operator good visibility and comfort during operation. Model: GT2000 Operating weight: 2,200 kg Engine type: Yanmar 3TNV80F Rated power: 15.2 kW Rotation speed: 10–12 rpm Maximum bucket digging force: 14 kN Maximum arm digging force: 10 kN Hydraulic system pressure: 18 MPa Maximum slope angle: 35° Travel drive: Single speed Swing arm: Yes Expandable tracks: Yes Joystick: Yes Standard bucket capacity: 0.06 m³ Rear swing radius: 1,125 mm Minimum digging height: 3,365 mm Maximum dumping height: 2,385 mm Maximum digging depth: 2,050 mm Maximum vertical digging depth: 1,955 mm Maximum digging range: 3,860 mm Minimum turning radius: 1,125 mm Dozer blade ground clearance: 230 mm Dozer blade maximum digging depth: 275 mm Swing arm angle left: 75° Swing arm angle right: 45° Cabin height: 2,270 mm Wheelbase: 1,230 mm Track width: 820 mm Minimum ground clearance: 210 mm

Condition: reconditioned (used), Year of construction: 2003, Cyklop XZE-311 strapping press Year of construction: 2003 Passage width: max. 2200 mm Passage height: max. 2200 mm Belt guiding distance: 625 / 440 Roll pitch: 60 mm Lrsdotqpadepfx Aagsh Strapping speed: 2.9 m/s Strap tensioning force of the strapping unit: adjustable up to 2000 N Pressing force: adjustable from 5 to 48 kN

Condition: good (used), WEBER tube extrusion line including: Lodjvryhyjpfx Aagorh WEBER DS 8.5 Elmepla saw Battenfeld R200/6 Battenfeld V125

Condition: used, Cutter Manufacturer: Seydelmann Lrjdpfx Aaetu I T Ejgoh Model: K 204 Ultra Made of stainless steel Volume: 200 liters 2 knife speeds 2 bowl speeds 2 mixing speeds Dimensions: 280x205x255cm Electric power: 78kW Voltage: 400V, 3 phases, 50 Hz

Condition: excellent (used), Year of construction: 2005, Basic data: Production year: 2005 Dimensions (LxWxH): 7580x4360x5120 mm Weight: 6000kg Operating voltage: 400/415V 50Hz Power consumption: 20kW Capacity at 20g/l: 1600kg/h Touch screen control panel Powder tank with screw feeder Lrodperfn Rvsfx Aagsh Complete documentation in both paper and electronic form (electrical schematics, CE compliance certificate, user manual) Condition: very good (machine clean and well-maintained, used exclusively for foaming white polystyrene) For an additional fee, our company can arrange transportation, as well as the installation and commissioning of the machine by our technicians at the location specified by the customer.

Condition: as good as new (ex-display), FULL LINE of Double-side Sizing-Milling & Edge Banding. Composed of the following machines: VZ0200A) Gantry-portal Loader (Double pick-up station) "BARGSTEDT" Mod. TBH 500/D/30/12 VZ0200B) 1st Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 525/8/A3/15 VZ0200C) In-feeding Rollerway "HOMAG" Mod. TDL 310/30/12 with 90° Turning device (from lenghtwise to crosswise) with double cone system VZ0200D) 2nd Double-side Sizing & Edge Bander "HOMAG" Mod. KFL 526/10/A3/30 VZ0200E) In-feeding Rollerway "HOMAG" Mod. TDL 510/25/12 with 90° Turning device (from crosswise to lenghtwise) with double cone system Lredpfx Aedt Rgvsagjh VZ0200F) Cleaning machine "WANDRES" VZ0200G) Gantry-portal Stacker (Double pick-up station) "BARGSTEDT" Mod. TSP 410/D/25/12