Machining centre with continuous feed

BIESSE SKIPPER 130

Condition: used, machine/vehicle number: 008563, X axis working area: 3000 mm Y axis working area: 1300 mm Total number of drilling spindles: 82 Fgedozruxvspfx Akvef

Condition: good (used), Year of construction: 2009, Machine will come with robot . Fgsdpfx Akjxfu S Novof 42.000 rpm

Condition: repair required (used), Year of construction: 2010, functionality: limited functionality, BIESSE Skipper 130 Fgedpfx Akszp Simjvsf - Year of manufacture: 2010 - Available from September 2026 - The lower drilling unit has a problem and needs to be repaired. - The machine is still in operation and can be inspected. - Please feel free to contact us if you have any questions.

Condition: used, Year of construction: 2012, power: 20 kW (27.19 HP), working width: 1,300 mm, number of spindles: 82, plate height: 90 mm, working length: 3,000 mm, The pick-up deadlines specified in the General Terms and Conditions apply. The absolute latest pick-up date is August 31, 2026! TECHNICAL DETAILS Working area, X-axis: 3,000 mm Working area, Y-axis: 1,300 mm Maximum panel thickness: 90 mm Total number of drilling spindles: 82 Drilling units, Unit 1 (top) Spindles for vertical drilling: 31 Spindles for horizontal drilling in the X direction: 8 Spindles for horizontal drilling in the Y direction: 2 Drilling units, Unit 2 (bottom) Spindles for vertical drilling: 31 Spindles for horizontal drilling in the X direction: 8 Spindles for horizontal drilling in the Y direction: 2 Milling spindles Number of milling spindles: 2 Milling spindles, Unit 1 (top) Number of controlled axes: 3 Motor power: 4.5 kW Milling spindles, Unit 2 (bottom) Number of controlled axes: 3 Motor power: 4.5 kW Grooving units Number of grooving units: 2 Grooving units, Unit 1 (top) Unit: Fixed for creating channels in the X direction Max. tool diameter: 160 mm Motor power: 3.5 kW Grooving units, Unit 2 (bottom) Unit: Fixed for creating channels in the X direction Max. tool diameter: 160 mm Motor power: 3.5 kW MACHINE DETAILS Total installed power: 20 kW Fodezf Ibdspfx Akvsgf Machine programming software: BIESSEWORKS EQUIPMENT Automatic panel stacking system with motorized transfer Barcode scanner (manufacturer: SICK) CE marking Protective grating Safety mats The machine is sold and delivered in its actual and legal condition (“as is, where is”) based on photographic documentation and technical/commercial documents with a descriptive nature. The buyer has the right to inspect the goods before pick-up and assumes responsibility for the installation, securing, and use of the machine at the destination. External reference: 8565

Condition: excellent (used), Year of construction: 2012, - 3-axis CNC center SCM Pratix S - model PRATIX 12B from 2012. - Range X, Y, Z axes: 2500x1250x150+ mm - Number of tool spaces in the magazine: 8 - Machine table: Raster aluminum table, 2 sections. - Control: PC control - Software: SCM NESTING, SCM XILOG MAESTRO - Serial no.: AH/115920 Fgedpfx Akjuu Ntgevsf Number of milling axes: 1 Drilling unit: 1 - practically unused Maximum spindle speed: 24,000 rpm Tool holder: HSK-F63 Main engine: 6.6 kW Table measurements: 130 cm x 260 cm Portal construction: Machine with movable portal Vacuum pumps: 2 pcs. BECKER from 2012 - one placed outside, the other installed in the machine. Vacuum pump capacity m³/h: 240/280 m³/h. Interface for reading CAD format (.dxf) Security: Rejects Weight approx. 2,500 kg Length: 5,900 mm Width: 2,790 mm Height: 2,190 mm Automatic tool length measurement

Condition: used, Year of construction: 2014, machine/vehicle number: 33041, functionality: fully functional, power: 4.5 kW (6.12 HP), travel distance X-axis: 3,000 mm, travel distance Y-axis: 1,300 mm, travel distance Z-axis: 90 mm, Equipment: CE marking, The machine has been regularly maintained and is in excellent working condition. Linear guides and ball screws are in excellent condition without any play. Input and output tables are fully functional. The transport clamps operate powerfully and in sync. The drilling system is equipped with 82 spindles. Both the upper and lower milling units use ISO 30 tool holders. The motor bearings are in good condition and run at 24,000 rpm. The machine is operated via the BiesseWorks interface. The electrical components inside the control cabinet are clean and dust-free. Fedpfey Sfi Iex Akvogf

Year of construction: 2008, condition: ready for operation (used), functionality: fully functional, * Wemhöner Basic 1000 Plus - Year of manufacture: 2008 - Very good condition, little used * Type: KT-MB-28/15-240 * With automatic pin system and inline turn-over device * 2 tables with automatic variable pin system * With Teflon coating for pre-glued foil * Foil laying system for the pin table (pre-glued foil) * Heating plate size: 2800 x 1500 mm * Maximum workpiece size: 2,540 x 1,250 mm * Membrane: Yes * Cutting station * Foil paternoster storage, 3.2 m height with 14 suspension rods * Siemens S7 PLC control * Operator panel for PLC control: SIEMENS TP 270 (touchscreen) * Automatic membrane tensioning * Installed power supply: 38.5 kW * Maximum chamber pressure: 6 bar * Maximum press opening: 150 mm Fgedjxbcudepfx Akvjf * 6 cylinders with Ø 125 mm * Operating voltage: 400V 50/60Hz * Press chamber height: 40 / 60 mm * Max pressing force: 2400 kN * Hydraulic system operating pressure: 320 bar

Condition: used, machine/vehicle number: 007135, Max. panel width: 800 mm Max. panel length: 2500 mm Fsdpfx Aot Hmppskvjgf Panel return for edgebander: Left

Condition: used, Year of construction: 2006, Numerical Control XP 600 Working range on X-axis mm 3060 Working range on Y axis mm 1140 Working range in Z axis mm 160 N ° 2 work fields Bar worktop No. 6 adjustable bars for suction cup support No. of pneumatic bakelite bars for panel lifting (?) No. 2 adjustable suction cups for each bar with vacuum seal for fixing the panel during processing No. 1 vertical electrospindle with C-axis 12 kW motor 10-position tool change system - positioned on the drilling head of the machine, ISO 30 type cones BH19L drilling head with 18 spindles arranged as follows: - No. 7 verticals on X axis - N° 6 verticals in Y axis - N° 4 horizontal on X axis - No. 2 horizontals on Y axis - No. 1 independent blade group for making grooves on the X axis Front protection and safety system with photocells Automatic lubrication system (?) Air conditioning system for cooling and cleaning of machine control Vacuum pump mc/h 250 TECHNICAL DETAILS TO BE CHECKED Fgedpjv Aacfjfx Akvof

Condition: used, Year of construction: 2017, total height: 1,800 mm, total length: 4,800 mm, total width: 1,000 mm, Colour: Grey Price: On request - Details: - └ Description: Machine is currently giving fault, error code empty machine - Year: 2017 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Number of units [pcs]: 9 - └ 1st unit type: Pre-milling unit - - Tools available: Yes - └ 2nd unit type: Glue unit - └ 3rd unit type: Pressure rollers Fedpjyll Snefx Akvegf - - Tools available: Yes - └ 4th unit type: Cap unit - - Tools available: Yes - └ 5th unit type: Corner rounding unit - - Tools available: Yes - └ 6th unit type: Radius scraping unit - - Tools available: Yes - └ 7th unit type: Corner rounding unit - - Tools available: Yes - └ 8th unit type: Flat scraping unit - - Tools available: Yes - └ 9th unit type: Brushing unit - - Tools available: Yes - Glue system: Glue pot - Voltage [V]: 400 - Current consumption [A]: 42 - Transport dimensions: 4800mm x 1000mm x 1800mm (l x w x h) Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels