2017 Biesse Selco SK 4 450 Twin Pusher 1.2

Biesse Selco SK 4 450 Twin Pusher 1.2

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Lajdexy Tmnjpfx Ac Ieb

Condition: refurbished (used), Year of construction: 2024, Manufacturer: Elumatec Type SA/ SAS 142 Overhaul year: 2024 Saw blade max. carbide: 500 mm Drive power saw motor: 4 KW Saw motor speed: 2800 min-1 Cutting speed saw blade 500 mm: 4400 m/min Saw height control: infinitely variable, fully electronic Working range square 90° max.: 130 x 130 mm Working range flat: 90° max.: 190 x 130 mm Working range round: 90° max.:150 mm Pneumatic feed length: 5-560, 10-1120 mm Compressed air connection, on site 6 bar Weight(saw)approx.: 800 kg Dimensions LxWxH (saw)approx.:2900mm x 1400mm x 1500mm Installation area LxW: 2900mm x 1400mm Additional description Elumatec SA/ SAS 142 4KW Retrofit Elumatec SA 142 4KW Retrofit Fully automatic sawing machine for non-ferrous metal and plastic After completion of the retrofit, the machine is in mint condition, both technically and visually. The machine will be overhauled in our company at the customer's request. Among other things, the following points were renewed: - Conversion to Siemens S7 PLC control - Conversion to Siemens HMI control panel - New electrical components - New pneumatic lines - Maintenance or replacement of all pneumatic cylinders and valve terminals - Maintenance of minimum lubrication system - Replacement of general wear parts - Overhaul of the cab Warranty: Unless otherwise agreed, we provide a 6-month warranty on all parts overhauled or replaced by us. Working time and wearing parts are excluded from the warranty. Optional: - Extension of the sawing area to flat 90° max.: 300 x 120 mm - Splitting extension (for a high-quality cut surface without return marks) - Servo-controlled material feed - Saw blade feed Servo-controlled Lajdpouiy Nyjfx Ac Ijb - Mass clamping device Feed vice - Delivery and installation on your premises - Training of your employees

Condition: used, machine/vehicle number: 007716, X axis working area: 3250 mm Y axis working area: 1220 mm Ljdpfxswuz N Nj Ac Ieab Working Table: Pod and Rail Main Electrospindle power: 12 KW Number of controlled axes: 4 axes Total number of drilling spindles: 18 Total number of tool changer positions: 16

Condition: used, Year of construction: 2017, machine/vehicle number: A1711012, Pos.1 VEN CLEAN Smart dedusting systemCompressed air dedusting for cleaning the workpieces to be painted from dust on profiled workpiece surfaces. Five rotating blowing stars are installed. These remove the dust from the surface. The loosened dust is extracted on both sides by suction shafts. on both sides. An external extraction system is required on site. Technical data: Roller transport length: 2,060 mm Roller pitch: 85 mm Working width: 1,300 mm Total width: 1,800 mm Drive power: 0.25 kW Exhaust air volume: 4,000 m³/h To be provided by the customer Compressed air consumption: 980 Nl/min. Ionisation as nozzle bar, not EX) with compressed air nozzles, Compressed air consumption 840LN/min. Pos. 2 Automatic spray gun VEN SPRAY Comfort- Manufacturer Venjakob - Type. VEN SPRAY Comfort CNC 7000 - Year of construction 2017 - Working height approx. 930mm+-20mm - Working width 1300 mm - Operating side left - Price for overhauled machine - Actual condition, machine not overhauled - Gun drive in duo version - Dry extraction system - Extraction nozzle diameter 500 mm Ljdpfx Acsu U Ryys Isab - Exhaust air capacity 10.000 m³/h - Belt conveyor system - Infinitely variable feed speed ~ 2-6 m/min - With belt cleaning system with doctor blade in tungsten carbide design - With option to install a second beltcleaning system. Software and electric parts inside. - Gun control, touch screen CNC7000 - Installed colour circles 1 pc. (optionally more possible) - Supply air filter cover - Suitable for water-based paints - Suitable for solvent-based paints - Control cabinet, free-standing - Length: 4.350 mm + (2,060 mm) - Width: 3.540 mm - Height: 2.600 + 440 mm - Volt, Hz 400 / 50 - El. Power 23,33kW / 63A - Colour RAL 7035 - Location, in stock Voltage fluctuations max. +/- 5 % _____ Optionally, we can also provide you with a quotation for the assembly and start-up of the system, as well as training for your employees. We also offer regular maintenance and servicing of the machine on request. For further information, get in touch with us!

Condition: used, machine/vehicle number: 006370, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Premilling Unit: yes Laodpol Txw Hefx Ac Ieb Corner Rounding Unit: yes Grooving Unit: yes Max feed speed: 25 m/min Maximum panel thickness: 60 mm Operating Units: 12 nr

Condition: ready for operation (used), Year of construction: 2009, Travel ranges working area 1: X: 6450mm, Y: 1535mm, Z: 250mm, working area 2: X: 6200mm, Y: 1535mm, Z: 250mm, working area 3: X: 6200mm, Y: 1520mm, Z: 275mm, axis travel configuration 1: X: 6820.5mm, Y: 1963mm, Z: 350mm, axis travel configuration 2: X: 6820.5mm, Y: 1963mm, Z: 350mm, axis travel configuration 3: X: 6820.5mm, Y: 1963mm, Z: 663mm (5-axis head), Z: 350mm (additional machining units), control: Biesse XP600. Maintenance: complete C-axis was replaced in 2015 including accessories, vacuum pump was fully replaced in 2016 including bellows, hoses and additional components, in 2021 the machine was equipped with a new high-performance control PC running a current Windows 10 operating system. With extensive documentation. An on-site inspection is possible. Laedpfx Aeylziioc Iob

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Laodpjxlqntsfx Ac Isb Edges (band in rolls) thickness (Min/Max) mm 0,4 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 8 (12)* Panels thickness (min/max) mm 8 / 60 Numerical Control "StarTouch" + "Touch 7" Feeding speed m/min 12-18 Top pressure system with rubber belt (C.N.) Spraying unit (Anti-sticking liquid) AAR In-feed fence, adjustable by N.C. "EASY SIZE PLUS" Pre-milling Unit (vertical joint trimmers) 2 x Kw Lamps to heat the workpieces side Glueing Unit (P.U.R. Glue + Quick Melt system) "VC/800" - "VC/6" + "AirFusion AF15" Band Pressure zone (N.C. adjustment) Edge coils supporting unit - 1 Snipping (end-cutting) K/SEL Rough Trimming unit RS/K Fine Trimming unit RI / 800 (3 pos.) Multi Function Unit (Profile contour Trimming Unit) “4 EDGE” KIT Spraying Unit (for sliding liquid) Profile edge scraping unit RAS/1000 Glue scraper RCA / 2C Milling grooving unit K-100 (1 x Kw 1,8) 90° Hot Air Heater (to reactivate the color of plastic tape) Panels Return System "SAG" Mod. SPINNER 47 / 63

Condition: like new (used), functionality: fully functional, power: 7 kW (9.52 HP), saw blade diameter: 305 mm, total length: 3,100 mm, total width: 3,100 mm, overall weight: 3,000 kg, cutting length (max.): 3,100 mm, cutting height with scoring (max.): 70 mm, feed rate X-axis: 40 m/min, feed rate Z-axis: 50 m/min, space requirement length: 3,100 mm, space requirement width: 3,100 mm, Equipment: rotational speed infinitely variable, scorer, Panel Sizing System SCHEER PA 4136 – 3100 x 3100 The PA 4136 is a high-performance, electronically controlled panel saw designed for precise, efficient, and automated cutting of wood-based materials. Ideally suited for industrial applications in joineries, furniture production, and panel processing. Condition & Service: Condition: Very good Functionality: Fully operational Warranty: 12 months CE-compliant and dust-tested (limit value < 2 mg/m³) Ljdpowrn Efsfx Ac Ijab Key Technical Data & Equipment: - Rip saw FM 20-3100 with hardened guides - Automatic forward & return travel of the saw unit (automatic lowering during return) - Feed drive via three-phase gear motor, frequency inverter controlled - Feed speed: 2 – 40 m/min (stepless) - Return speed (rapid traverse): 50 m/min - Extraction channels in machine base & pressure beam - Score saw blade adjustable externally (without opening the hood) - Safety hood locking with lamella curtain SZ 5008 - 3-step cutting height adjustment LA 4143 - 6 cut-out sections in the pressure beam for residual cuts down to 5 mm - Saw motor: 7.0 kW | Scoring motor: 1.1 kW (switchable) - Cutting length: 3100 mm | Cutting height: 70 mm Material Handling & Feed: - Angle pressure device WP 5003 with clamping claw for cross cuts - Adjustment range: 2400 mm - Fully automatic control via DNC-AT - Material feed table HP 5091 - 2 upper guides, rack-and-pinion guidance - Servo drive for material pusher - Feed speed: 25 m/min (safety limited) - Return: 40 m/min - 6 clamping fingers, 4 double roller tracks - Table length: 3100 mm | Fence depth: 3150 mm - Closed Pertinax surface in the area of the angle fence Control & Operation: - Operating system: Ubuntu Linux - Integrated PC with hard disk, parallel & serial interfaces - Network capable (LAN/WLAN), remote maintenance via internet (TeamViewer, Remote Desktop) - USB printing function - Multilingual dialog programming - 15" flat screen, multifunction keyboard on a swiveling control console - Graphic display of cutting plans and processes Software / Programs: - OPTIMAX: Office optimization, waste calculation, material requirements - OPTIMIN: Direct optimization at the machine PC with parts list entry - Processing via USB, diskette or online (optional) - Manual, automatic & special operation modes (e.g. grooving, veneered parts) Additional Equipment: - Angle fence table HP 5085: 1,720 x 800 mm | Pertinax overlay - Workpiece support table HP 5025: 1,720 x 800 mm | Pertinax overlay - Air cushion system LK 5030 integrated in both tables - Circular saw blade KSB 4005: Ø 305 mm, Z = 60 - Circular saw blade KSB 4006: Ø 200 mm, Z = 60, tapered Reliability in Continuous Operation: This machine is in use worldwide – under extreme conditions. Whether in the dry climate of Africa or in high humidity regions of Southeast Asia (e.g. Thailand): The PA 4136 runs reliably in 3-shift operations – 365 days a year – and stands out for its outstanding stability and durability. Warranty: We are so convinced of the quality and stability of our machines that we offer a 7-year warranty on the machine frame and guideways. (Excludes electronic supply parts and wear parts.) 📞 Contact us for an individual offer or to arrange a viewing appointment. Machine available from stock. Delivery, commissioning, and training available upon request.

Condition: refurbished (used), Year of construction: 2009, Screen Printing Machine ADCO Squeegee Cutter SC061 (2009). Ledoxk T Hpspfx Ac Isab Sartech is a company specializing in solutions for screen printing, automation, and robotics, as well as the manufacture of UV (electronic) or hot air tunnels.

Condition: used, machine/vehicle number: 008127, Position 1: Single Edgebanders BIESSE + FORMETAL-AKRON 1440 A Position 2: Panel Return Systems BIESSE + FORMETAL-AKRON 1440 A Lajdpfx Acsw Tq Iwo Ijb