COPY SHAPER machine BALESTRINI C70N

BALESTRINI C70N

Condition: excellent (used), Year of construction: 1982, BALESTRINI Double Tenoner: Maximum working width: 360 mm Maximum working height: 120 mm Minimum working length: 240 mm 2 spindle heads with 2 x 7.5 HP motors Feed motor: 1 HP Nedpfx Afsxuwa Ijaola Weight: 1,100 kg 2 return conveyors for workpieces

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: Nljdpfx Ajwp Rqfofaea • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: excellent (used), Weinig Unimat 500 four-sided planer Working width 230mm Working height 140mm Nlodpfjthk T Iex Afaoa Number of spindles 6 Spindle arrangement: 1.Bottom 7.5kw 2.Right 7.5kw 3.Left 7.5kw 4.Top 11kw 5.Top 11kw 6.Bottom 7.kw Total power 56kw Feed speed adjustable on inverter Memory system Pneumatic pressure divided into 3 sections 4 rows of metal material feed rollers 2 rows of rubber drawing rollers 1 roller in the tabletop driven by a cardan shaft Length of input table top 1980mm Worktops made with Marathon Coating technology CE certificate Extraction stubs 6x140mm Machine dimensions 394x185x195cmH

Condition: used, Year of construction: 1997, - edge banding unit Nljdpfxsd Inkts Afaea - Cross-cutting unit - Milling unit - Fine trimming unit - scraper - buffing unit

Condition: new, Year of construction: 2024, Boring and inserting machines Rilesa Vlg 2200 new 2023 Make: Riles Model: Vlg 2200 Description: Condition: new Year: 2023 Start type: to be agreed Cost of delivery: Nodpfx Afsgbpmhjajla Customer cover Conditions of delivery: OWN RECEIPT Category: Machine Tools equipment in Poland Subcategory: Drills Subcategory 2: Drilling machines Description DRILL DRILL WITH STORAGE 8 DRILLING UNITS TWO FRONT RIGHT AND LEFT, 3 UPPER AND 3 BACKS Year: 2023 new

Condition: excellent (used), Genini Miniautomatic Pass-Through Lathe Njdpsv Hgctjfx Afajla Turning machine from square timber Main spindle with a two-speed motor with a power of 4.9/5.9kw Hydraulic pump motor with a power of 1.5kw Maximum length of square timber 950mm Maximum turning length 120mm Maximum turning diameter 80mm Two supports with profiling knives 1 front spindle for drilling or front profiling 1 roughing turning knife Machine weight approx. 1800kg

Condition: as good as new (ex-display), Year of construction: 2025, Pressing area: 3000 mm x 1500 mm Operating vacuum: -0.85 bar Vacuum pump flow rate: 40 m³/h Pump power: 1.5 kW Noise level: 70 Db Heating temperature: max. 200 °C Heating power: 16 kW Machine length: 3100 mm Nsdpju Egp Isfx Afajla Machine width: 1650 mm Machine height: 1750 mm Weight: 950 kg

Condition: good (used), Year of construction: 1992, Single-piece sanding machine sanding from top and bottom electric height adjustment with digital display Nsdpfewyda Usx Afasla continuously variable feed speed star/delta starter pneumatic belt tensioning main switch sanding belt oscillation finishing brush unit top and bottom, manual height adjustment Working width: 190 mm Working height: 4 - 150 mm Min. workpiece length: approx. 280 mm Abrasive belt dimensions (L x W): 1850 x 200 mm Feed speed: 5 - 25 m/min Installed power: approx. 14 kW Extraction port diameter: 2 x 180 mm Dimensions (L x W x H): 2000 x 1000 x 2050 mm Weight: approx. 1800 kg Incl. infeed and outfeed roller conveyor (L = 1600 mm, non-driven) Note on used machines: • Technical data subject to errors and prior sale. • Quoted prices are ex-works – loaded free of charge! • The machines have been cleaned and function-tested. • All machines are sold as inspected, with no claims to warranty. Buyers are welcome to inspect machines at the location. • Special agreements are only valid in written form. (We answer inquiries only when your address and telephone number are provided!)

Year of construction: 2004, condition: excellent (used), Four-side planer -max. planing width 23cm -max planing height 16cm -2 pulling rollers in the table -chromed table - smooth regulation of the feed speed -2 pulleys from the top in front of the lower head, additionally a roller apparatus for short elements - 4 spindles: lower 5.5kW, right 5.5kW, left 5.5kW, upper 7.5kw Njdpfxshlp D Nj Afasla The machine is in very good condition, little used, with spiral heads on the bottom right and left, with a Terssa knife head on the top.

Condition: reconditioned (used), functionality: fully functional, Plate size: 1250 x 1500 mm Forming area: 1200 x 1460 mm Nledpfx Afowf Ea Toasa Drawing depth: 700 mm If you would like further details or a quote, please contact us.