Green sorting line

Almab, Sweden Horizontal pockets

Year of construction: 2023, condition: ready for operation (used), Two Vecoplan scraper chain conveyors are available. 1) VKU 800, year of construction: 2023, drive power: 5.5kW, belt speed: 24m/min, conveying capacity: approx. 120m³/h, belt width: 820mm, max. incline: 70°, section length: 10.2m. 2) VKU 1100, year of construction: 2023, drive power: 11kW, belt speed: 24m/min, conveying capacity: 180m³/h, belt width: 1150mm, max. incline: 70°, section length: 22mm. Documentation available. On-site inspection is possible. Ksdpot Iw Ryjfx Akxsdk

Condition: excellent (used), Storti RM 500 edger - Italian production - year of production 1993 - electric spacing of discs TECHNICAL PARAMETERS: - cutting width max 435 mm - cutting height max 170 mm - engine power 2 x 22kW - max element width 600 mm - minimum material length 800 mm - max disc diameter 600 mm - spindle diameter 40 mm - two upper pulling rollers - one upper pressure roller - roller motor power 2 x 1.1 kW - roller pressure with automatic jump - seven bottom pulling toothed rollers - electric disc adjustment - two lasers - feed speed 25 and 50 m/min Kodok Talpjpfx Akxjdk - feeding table 2950 mm - receiving table 3000 mm - drive rollers D100 mm - power of the roller feed motor 2 x 1.5 kW Transport dimensions 500x240x180 cm weight 3500 kg

Condition: used, Selling as a package Dominant 715, Dominant 547 & PlateRite CTP Kjdpfswxtrqox Akxodk Please see out other adverts to see the other machines. One color offset. Format A2

Condition: used, SPE Renergi Low Temperature Dryer. The Renergi Dryer is used for drying of sawdust and other materials for production of biofuels. The dryer can dry sawdust, bark or wood chips from a humidity level of about 50% to a level of approximately 10 %. This low-temperature dryer utilizes warm (or hot) water from a recommended temperature of 65°C and higher. Maximum water temperature - 110°C. Power supply safety: The dryer must only be fed by 3x400 V AC (630 A) 50/60 Hz with a separate Protective Ground conductur. Power supply Data: • Voltage 400 V AC, three phase • Recommended fuses in supply line: maximum 3x630 A • Typical power consumption: 200kW Ksdpjwp Rqfefx Akxsdk The dimension of the Dryer are roughly 17,4 by 5,7 meters, with a height of 10,7 meters. The floor space required is approximately 21,4 by 8,0 meters. A ceiling height of at least 15 meters (or 4 meters above the top of the media inlet). Air supply: at least 24 kg gas/s fresh air is required for the operation of this machine. This corresponds to 20nm3/s, or 72 000 nm3/h. Airflow: max 200 liter/min Air pressure: min 4,5 bar, recommended 6,0-8,0 bar Water supply: hot water supply, with a flow of 32 dm3/s. Water pressure: min 1.5 bar, max 6.0 bar Operating temperature range: • Incoming air temperature: -20°C to 50°C • Relative humidity: 0% to 60% Raw material/media: • Relative humidity: 45% to 55% by wieght • Requested relative humidity: 8% to 15% in the dried material Capacity: • The dual-cell, 4 m wide dryer can typically handle 2400 kg of material with a moisture content of 55% by weight in each load • The dryer is capable of drying 6000 kg raw material, with a water content of 55% to 10% in approximately one hour. SRE’s dryer is desinged in accordance with European directives. The equipment is designed to conform to the essential requirements of: • The Machinery Directive 2006/42/EC • LVD 2006/95/EC • EMC 2004/108/EC The dryer is located in Straupe parish, Cēsis district, LV-4152, Latvia. Available for viewing on working days, 08:00 to 17:00, by prior agreement on the viewing time. The dryer is already dismantled All electrical schematics, manual, operating instructions available Upon request, we can provide a contact person with this type of working dryer for consultation Price:20,000.00 EUR (VAT is not included)

Condition: reconditioned (used), functionality: fully functional, approx. 4.5 m long infeed and centering table Drive via chain from the feed motor Kjdpfx Akeu Hmacexedk Centers the logs in the middle of the rotor Debarking machine VK 26 4 main cutters 4 pre-cutters 30 KW main motor 11 KW feed unit non-driven extraction table Machine workshop checked Machine cleaned and repainted

Condition: excellent (used), Year of construction: 1988, functionality: limited functionality, machine/vehicle number: 25.05.004, total length: 9,500 mm, total width: 2,250 mm, total height: 2,300 mm, input voltage: 380 V, power: 50 kW (67.98 HP), overall weight: 21,000 kg, empty load weight: 18,000 kg, compressed air connection: 7 bar, Equipment: documentation/manual, Paper size: 730 x 1060 mm, printing area: 710 x 1040 mm Kdsdpfx Akeuf Sy Aoxek Paper thickness: 0.05 mm – 0.5 mm Preset maximum speed (due to simulation of the throw-off time for high-speed presses) is 4,000 sheets per hour, but the machine can operate much faster for commercial jobs. Four-fold central impression cylinder that prints all 4 colors in one gripper closure. 1988 FAG Speedproof with operator console for ink duct and cylinder adjustments, enabling extremely accurate register printing. Attached is the original factory brochure. The machine has been fully dry ice cleaned, and the cylinders are in excellent condition. Offered strictly on an 'as is, where is' basis. Maximum width is 225 cm, maximum height is 230 cm; shipping in a High Cube container is possible. Price is absolutely fixed, based on the removal of easily separated parts which we could sell separately, such as the Mabeg feeder with vacuum belt delivery, and the four-fold Baldwin stainless steel unit—with each color having its own bath, a mixer, and adjustable temperature control, so all four baths can be set to different temperatures and alcohol concentrations. The machine was dry ice cleaned, and it was intended for prominent use in printing electronic paper. However, due to too many initial losses, the project was discontinued. The machine has been with us for 3 years and, due to its size, I want to sell it as quickly as possible. Hence this very low price. It is an excellent machine. If the machine needs to be set up for testing and sampling, this is possible at an additional cost of €10,000, of which €5,000 must be paid in advance as a deposit under agreed conditions. All relevant information can be found in the original FAG folder for the machine, available via this advertisement as a PDF. Technical Data - Printing size max.: 710 × 1040 mm (27.95 × 40.94 in.) - Paper size max.: 730 × 1060 mm (28.74 × 41.73 in.) - Paper size min.: 500 × 700 mm (19.68 × 27.56 in.) - Stock thickness: 0.05 – 0.5 mm (0.002 – 0.020 in.) - Plate size max.: 800 × 1080 mm (31.50 × 42.50 in.) - Plate thickness: 0.25 – 0.5 mm (0.010 – 0.020 in.) - Speed max.: 4,000 sheets/h - Floor space requirement (incl. access to feeder, delivery, and central control desk): 950 × 525 cm (374 × 206.69 in.) - Press height: 230 cm (90.55 in.) - Weight (including paper stacked in feeder and delivery): approx. 18,000 kg (approx. 39,690 lbs) - Total power requirements: approx. 50 kW - Compressed air supply: 6 – 7 bar

Year of construction: 1998, condition: excellent (used), functionality: fully functional, Very stable creel roller conveyor with hydraulic lift and lowering cross conveyor. 1st part: Length 7,100 mm. Roller length 2,000 mm. Roller diameter 220 mm. Overall height 1,000 mm. Built-in hydraulic lifting and lowering cross conveyor With 4 chain strands. Spacing: 1,500 - 1,300 - 1,000 mm. Fully plated. Hydraulic model support rollers. Drive via geared motor. New bearings. 2nd part: Length 7,200 mm. Roller length 1,600 mm. Conveyor length 6,100 mm. Built-in hydraulic lifting and lowering cross conveyor with 6 chain strands. Unsupported, it is possible to convey the cut material under the roller conveyor to the left or right. Fully plated. Including hydraulic unit for both roller conveyors. Ksdpjt Hg Husfx Akxodk

Condition: new, power: 90 kW (122.37 HP), Year of construction: 2026, A double rotor hammer crusher is a type of crusher in which two rotors are mounted on a single shaft, combined to form a spinning rotor. The double rotor arrangement enhances the crushing capabilities and provides a more efficient and reliable crusher design compared to single rotor crushers. Here are some key features and aspects of a double rotor hammer crusher: Kedpfx Ajq Nf Enjkxodk 1. Two Rotors: As the name suggests, the crusher has two rotors that rotate in opposite directions on a common shaft. This dual rotor configuration allows for increased impact and crushing power. 2. High Capacity: The dual rotor design enables the crusher to handle larger feed sizes and higher capacity compared to single rotor crushers. It is suitable for crushing materials with high hardness and large sizes. 3. Versatility: Double rotor hammer crushers are versatile and can be used in various applications, including the reduction of limestone, gypsum, coal, and other similar materials in the mining, cement, and building materials industries. 4. Impact Crushing: The primary mechanism of crushing in a double rotor hammer crusher is through the impact of the hammers against the material. The material is fed into the crusher, and the high-speed rotating hammers impact and shatter the particles. 5. Adjustable Gap Settings: These crushers often have adjustable gap settings between the rotors and the impact bars, allowing control over the final particle size. 6. Durability: The robust design of the double rotor hammer crusher makes it durable and capable of handling tough materials and continuous operation. 7. Reduced Wear: The dual rotor arrangement can help distribute wear more evenly across the hammers and other wear parts, potentially extending the overall lifespan of the crusher. Typical Technical Specifications While exact numbers vary by manufacturer, these are the standard ranges for industrial models: Model (Rotor Size),Max Feed Size,Output Size,Capacity (t/h),Total Motor Power 600 × 400,≤110 mm,≤3 mm,10 – 15,18.5+18.5 kW 800 × 600,≤120 mm,≤3 mm,40 – 50,45+45 kW 800 × 800,≤180 mm,≤3 mm,50 – 60,45+55 kW 1000 × 800,≤180 mm,≤3 mm,70 – 80,75+55 kW 1100 × 1000,≤200 mm,≤3 mm,70 – 100,90+110 kW 1400 × 1200,≤200 mm,≤3 mm,90 – 110,132+160 kW For more details about double stage hammer crusher, or double rotor crusher, welcome to leave us a message, our team will get back to you at the earlist.

Year of construction: 2023, condition: new, PLASMA CUTTING MACHINE MODEL MTX 1500/3000 Construction: steel+aluminium Overall dimensions: 3350/2200/1300 Working area: 3100/1520/140 XY axis drive: 4Nm stepper motors with gears, precision grade 8 Z axis drive: stepper motor ball screw Travel speed: up to 25m/min Z axis control system: THC My plasma system Collision protection system to prevent burner damage Linear guide: TBI Automatic material detection system Power supply: 240V Maximum load: 1700kg Total weight: 1200kg net INCLUDED: - control panel -water table -exchangeable grate Kdjdpeh Rabnofx Akxek -control software in German, English, Polish -Certification of conformity CE - DTR - warranty The possibility of selecting the appropriate Hypertherm cutter to individual needs of the company.

Year of construction: 1988, condition: repair required (used), mechanisation for planer infeed -For lengths up to ca. 13 m -Ideal unit for KVH (solid construction timber)and BSH (laminated beams) in front of the planer -1 operator -lateral destacking unit -separation Kedpfx Aksvbtpexjdk -4 cross cut saws -cutting cross section 180x220 mm, 150x300 mm