Sharpening machine

WEINIG Rondamat 168

Condition: used, Year of construction: 2023, DOUBLE GLASS BEAD SAW TRF 527 VIS CE 1 pc DOUBLE GLASS BEAD SAW TRF 527 VIS CE TRF 527 VIS: Double miter saw for the simultaneous cutting of two glass beads positioned one above the other. The right saw unit is fixed, adjustment of the left unit is via the set cutting length can be read off a digital display. The units have supports that allow two glass beads to be cut simultaneously. The upper support can be removed for cutting larger cross-sections. After the cutting process is completed, the pneumatic clamping cylinders automatically swing to the side to simplify loading and unloading of the machine. STANDARD EQUIPMENT • Fixed unit on the right • Digital dimension display • Pressure switch • 2 HM-tipped saw blades • Electrical system with motor brake, undervoltage release, motor protection switch • Pressure switch • Tool set • Guards with horizontal clamping devices, pivoting • Two-hand control • Belt drive • Pneumatic unit lift • Middle support TECHNICAL DATA • Motor power 2 x 1.2 kW • Saw blade diameter Ø 220 mm • Max. cutting height without support 80 mm • Max. cutting width at 90 degrees 55 mm • Max. cutting width at 45 degrees 40 mm • Max. cutting length 2800 mm (optional 4000 mm) • Min. cutting length 158 mm • Weight 217 kg • Space requirement (standard equipment) 3000 x 850 mm Extended cutting capacity 1 pc Maximum cutting length • 4000 mm Star stop 4 positions 1 pc set 2 mechanical stops for adjusting up to 4 intermediate angles. Additional center support. 1 adjustment for rebated profiles. 1 adjustment for rebated profiles as per drawing: - Attachment to the clamping devices to compensate for the profile inclination - Allowances on the rear stops of the units and the center support. The sketch below shows (in green) a beveled presser that follows the inclined profile and presses it against the allowance on the stop (shown in red). Rcsdpfexnlgcsx Acdob Storage location: Garbsen

Condition: ready for operation (used), 🔧 Key Specifications Rcedswnx Uispfx Acdjb Cutting System: Four-shaft configuration with two cutting shafts and two clearing shafts. Cutting Disc Diameter: Approximately 280 mm (11 inches). Cutting Unit Dimensions: Working width of 1,000 mm and length of 700 mm. Hopper Opening: Approximately 1,400 mm x 1,600 mm. Motor Power: Typically equipped with two 18.5 kW motors. Operating Speed: Low-speed operation at around 25 rpm for high torque and reduced noise levels. Weight: Approximately 2,500 kg

Condition: used, TECHNICAL DETAILS - Number of axes : 9 - Number of spindles : 2 Rodpfx Acjuwd Ryedocb MAIN SPINDLE - Max. bar diameter : 16 [mm] - Travel : 205 [mm] - Spindle speeds : 10.000 [rpm] - C axis indexing precision : 0,001 [°] COUNTER-SPINDLE - Max. bar diameter : 16 [mm] - Spindle speeds : 10.000 [rpm] - C axis indexing precision : 1 [°] GUIDE BUSH HOLDER 1 - Number of positions : 10 - Number of motorized positions : 4 - Live tools speed : 8.000 [rpm] SECONDARY OPERATION - Number of positions : 5 - Number of motorized positions : 3 POWER SUPPLY - Supply voltage : 400 [V] WEIGHT & DIMENSIONS - Machine floor space : 2.269 x 1.160 [mm] - Machine height : 1.693 [mm] - Machine weight : 1.800 [kg] EQUIPMENT - CNC : Mitsubishi MELDAS - Rotating guide bush - Parts catcher - Ejection of workpiece - Coolant tank - Bar loader : LNS Hydrobar Express 332 - Fire extinguisher * NB : working order not guaranteed. To have it checked by a qualified organization of the buyer.

Condition: good (used), Year of construction: 2006, machine/vehicle number: 108111, functionality: fully functional, working width: 240 mm, planing height: 160 mm, working height: 180 mm, Four-sided planer after service inspection, machine weight 3900 kg Rjdevrq U Depfx Acdocb

Condition: like new (used), Through feed double end trimmer saws. 2x 3kW saw motors. Feed motor with variator. 300mm to 3100mm end trimming capacity. Rcjdpfxjif N Sxj Acdeb Suitable for use with a moulder infeed or similar.

Condition: excellent (used), WEINIG Hydromat H23 Line, S/N 87321, year 1999, Ref-No. 103437 WEINIG Cross Conveyor HighMech E-1, equipped with 6 flat chains approx. 2000 x 3500 mm Hydraulic WEINIG Accelerator Model 814 Short infeed table with heavy-duty 4-roller feed unit Planer/moulder with reinforced KASCHWIG three-sided soundproof enclosure • Max. working width: 230 mm • Max. working height: 160 mm • Electronic feed, frequency-controlled, 8–80 m/min • Feed motor 18.5 kW • 1st spindle bottom 11.0 kW • 2nd spindle right 11.0 kW • 3rd spindle left 11.0 kW • 4th spindle right 11.0 kW • 5th spindle left 11.0 kW • 6th spindle top 15.0 kW • 7th spindle bottom 11.0 kW • 8th spindle top 15.0 kW • 9th spindle bottom 15.0 kW • 10th universal spindle 11.0 kW (four-sided) • Spindle speed 6,000 rpm • Spindle diameter ø 50 mm • All spindle motors equipped with NEW motor start/stop brake units • Pneumatically supported top pressure rollers • Feed rollers D=140 mm • 6 driven rollers in the table • Spindles 1 + 6 + 7 + 8 + 9 with counter bearings • Spindles 8 + 9 with straight jointer • Spindles 8 + 9 with profile jointer • Spindles 6 + 8 with pneumatic pressure • Reduced spacing between feed rollers • Hard-chromed table plates • Hard-chromed fences • Pneumatically supported side pressure rollers • Automatic table lubrication • Centralized lubrication points • Free-standing control panel • Connected load approx. 145 kW / approx. 400 A • Free-standing electrical cabinet • Operating instructions, spare parts list and wiring diagram included • Machine sold without cutterheads Machine dimensions approx.: • Length: 6,000 mm • Width: 2,250 mm • Height: 1,800 mm • Weight: approx. 8,500 kg Factory-new WEINIG components installed: NEW horizontal/vertical spindle NEW counter bearings All spindles with HL bearings All motors newly fitted NEW electronic motor soft start/brake devices NEW hard-chromed table plates NEW hard-chromed fences Many other new parts fitted in the machine Condition: see attached photos – technically in excellent condition Infeed mechanization unrefurbished – complete – fully functional Rjdpfx Aswvqkljcdecb Payment: Net cash before loading Delivery time: By arrangement Delivery: EXW Inspection: Anytime by appointment Errors and prior sale excepted.

Condition: used, No. 3176 Automatic planer and moulder WEINIG Hydromat 1000 Used, year of construction 2007 6 spindles: bottom-right-left-top-top-bottom Electronic feed 6 - 60 m/min Working width 80 - 150 mm Working height 23 - 65 mm Finished slat widths 4 - 15 mm Max. Max. number of slats 16 pieces Slat lengths 400 - 4000 mm 1st spindle horizontal at the bottom Brake motor 11 kW, 6000 rpm Spindle diameter 45 mm Tool flight circle 125 - 180 mm 2nd spindle vertical right Brake motor 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm 3. spindle vertical left 7.5 kW, 6000 rpm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment travel 80 mm Pressure shoe in front of the spindle, swiveling away, pneumatic roller contact pressure 4. spindle horizontal top 15 kW, 6000 rpm, diameter 45 mm Tool flight circle 112 - 250 mm Max. Moulding depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic 5. horizontal top spindle as saw spindle Brake motor 37 kW, 5000 rpm Diameter 45 mm Axial adjustment travel reduced to 25 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm Split pressure shoe in front of upper spindle, adjustable and swiveling away, pneumatic Rcsdpsu Agh Sjfx Acdsb 6. horizontal spindle at the bottom as saw spindle Brake motor 30 kW, 5000 rpm Axial adjustment travel reduced to 25 mm Diameter 45 mm Tool flight circle 112 - 250 mm Max. Sawing depth 35 mm Axial adjustment path 45 mm All moulder spindles with high-performance bearings Electronic feed 7.5 kW Adjustment travel of the feed rollers compared to the left-hand spindle, axial 35 mm Shorter roller distance compared to the right-hand spindles Running meter counter, electric, with 2 counters Short infeed table (1.2 m) with 2 driven rollers above the table 1 driven, toothed roller in the table, lateral pressure roller Automatic waxilite pump / lubricant pump Machine with 4-roller extension, pendulum shafts extended to 200 mm 2 driven, toothed rollers in the outfeed table 2 driven, toothed rollers in the machine table Pressure beam before and after upper spindle with mechanical digital display DigiSet (digital double display) for left and top spindles Electrical height adjustment of the upper spindles and the feed Machine already dismantled and stored Sale on behalf of customer, ex location near South Tyrol, without transportation and assembly Subject to errors in the description and price Transportation and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection by appointment is possible and recommended Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “purchased as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: excellent (used), Year of construction: 2021, operating hours: 9,500 h, functionality: fully functional, machine/vehicle number: 3284, Standard version of RUF Lignum R2 with outfeed channels, el.motor 22 kW, briquette sizes 150x60 mm capacity up 500 kg/h Redpfx Acsyyl Srjdocb

Condition: excellent (used), belt driven Flow rate 14500 m3/h Negative pressure 3091 Pa Motor power 22 kW Speed ​​2340 rpm Suction DM 500 mm Outlet DM 400 x 500 mm Dimensions L x W x H = 1800 x 1300 x 1250 mm Advise used machines: • Technical data without obligation, mistake and intermediate sale reserve. • Price is considered ex-location price Redpfxeh Tfqho Acdjcb • All articles or machines are bought as seen without any entitlement on warranty. • It is left to the choice of the buyer to view the machines before at its location. • Special arrangements are possible but only valid in written form. (We answer your inquiries only with stated address + telephone number!)

Condition: new, Year of construction: 2025, the SQUALO 615 multi-blade or multi-blade circular saw with single shaft is a technological machine, indispensable in a modern sawmill to optimize the production of sawn timber. moreover it is 2-in-1 as it can be configured as a trimming machine with 1 or more movable blades. ideal for the production of strips, squares, sawn timber, profiles, edged planks, prisms, boards, elements for pallets. Rollers / conveyor belt width 620 mm Width of infeed / outfeed conveyor rollers 620/720 mm Rsdpfxjhpbxio Acdscb Max saw unit width 590 mm Max cutting height (without pad) mm 150 (mm 125 Trimming machine) Min. Length working mm 800 Max width passage 800 mm Blades hole diameter mm 80 (mm 104 Trimming machine) Circular blades diameter 250/470 mm (480 mm Trimming machine) Blade shaft speed rpm 3.800 Variable feed speed with ROLLS 3 - 36 m / min Variable feed speed with CARPET m / min 4 - 25 optional: softstarter start