Lead/traction spindle lathe

Weiler Commodor Geometrisch Überholt

Condition: like new (used), functionality: fully functional, Weiler Commodor Lead and Feed Screw Lathe with 3-axis K&C Digital Readout, newly overhauled, with acceptance protocol for tolerances equivalent to new machines. Technical Data: >> Machine Serial No.: 2268-87 >> Centre Height: 180 mm >> Distance Between Centres: 1000 mm >> Spindle Speeds: from 13 to 2000 rpm >> Spindle Bore: 56 mm >> Short Taper Spindle Nose DIN 55029 Camlock >> Tailstock Morse Taper 4 >> Feed Rates: 0.026 to 0.888 mm/rev >> Thread Cutting Capability: Metric, Inch, Module, and Diametral Pitch >> Metric Thread Pitches: 0.35 to 12 mm >> Weight: approx. 1500 kg >> Spindle Brake can be engaged >> Drive Power: 2.0/4.0 kW >> Dimensions (LxHxD): 2.2 m x 1.5 m x 1 m Hfjdpfx Agjymznhsfsf Equipment and Accessories: >> 3-axis K&C Digital Readout, new, with 12-month manufacturer’s warranty and manual >> NEW 3-jaw chuck, 200 mm, with 2 sets of jaws >> Multifix size B with 3 new tool holders >> Bed stop >> Machine feet >> Coolant system >> LED machine light Safety Features: >> Electronic spindle guard >> Spindle brake >> 2 emergency stops Optional: Lead and feed screw covers available on request About the machine: For sale is a Weiler Commodor lead and feed screw lathe in geometrically overhauled condition. The ways have been reground or hand-scraped. Acceptance is according to inspection protocol. Finished in 2K gloss white paint. Multifix toolpost and chuck are new. For safety: The machine is equipped with a brake motor, electronic spindle guard, and two emergency stops, making it an as-new lathe. Even at high spindle speeds, the Weiler runs very smoothly. This newer generation of Weiler lathes is extremely user-friendly and is capable of producing ground-like surface finishes. Take advantage of the opportunity to inspect the machine under power on-site and see its condition for yourself.

Condition: ready for operation (used), functionality: fully functional, spindle bore: 42 mm, center height: 165 mm, center width: 635 mm, spindle speed (max.): 2,500 rpm, spindle speed (min.): 30 rpm, overall weight: 900 kg, Ladies and Gentlemen, We are selling a Colchester Master 2500 lathe with Heidenhain digital readout. The machine is fully functional and can be tested on site. Availability: immediately Center width: 635 mm Center height above bed: 165 mm Center height above support: 105 mm Spindle bore: 42 mm Spindle speed: 30 - 2500 rpm. 16 steps Inner tailstock taper: MK 3 Hfjdpfxju St S As Agfef Drive power: 3.7 kW Space requirement: (LxWxH) 1700 x 880 x 1200 mm Weight: approx. 850 kg

Condition: like new (used), functionality: fully functional, Weiler Commodor guide and feed spindle lathe with 3-axis digital display K&C NEW Overhauled with acceptance certificate for tolerances of new machines Technical data: >> Machine no. 1824 >> Center height 180 mm >> Center width 1000 mm >> Spindle speeds: from 13 to 2000 rpm >> Spindle passage 56 mm >> Short taper spindle head DIN 55029 size 5 >> Tailstock MK 4 >> Feed rates from 0.026 to 0.888 mm / rev Hsdpfx Aovrcqdogfsff >> Possible threads metric, inch, module and diametric pitch >> Metric thread pitches from 0.35 to 12 mm >> Weight approx. 1500 kg >> Spindle brake can be switched on >> Drive power 2.0/4.0 KW >> Length 2.2 m, height 1.5 m, depth 1 m Accessories and equipment: >> 3-axis digital display from K&C New, 12-month manufacturer's guarantee with operating instructions Functions: Switching mm/inch, coordinate selection ABS/INC, halving of the display value, reference mark, tool programming 200 pcs., cone calculation, radius / diameter, quick zeroing, switching of the counting direction, >> Three-jaw chuck wedge bars as good as new 200mm 1 set of jaws >> Mulifix size B with 2 pcs steel holders NEW >> Bed stop >> Machine feet >> Coolant system >> LED machine lamp For safety, the machine is equipped with: >> Electronic spindle protection >> Spindle brake >> 2 emergency stops On request: covers for the guide. and feed spindle About the machine: A Weiler Commodor guide and feed spindle lathe is offered in a geometrically overhauled condition. The guides have been reground or re-scraped. With acceptance according to the test report. 2K glossy white paint. The Multifix and chuck accessories are new. For safety: The machine has a brake motor, electronic spindle protection and two emergency stops - an absolutely new lathe. Even at high speeds, the Weiler runs very quietly. This new generation of Weiler lathes is very user-friendly and surfaces can be produced as if they were ground. Take the opportunity to view this machine on site under power and see for yourself its condition.

Condition: new, AXA 360° swivel cantilever crane Max capacity : Kg 500. Max height : mm 2804. Max overhang : mm 1360. Easily maneuverable due to 360° rotation and high load capacity pivoting wheels with bumper supports and parking brakes. Due to the frontal footprint of only 995mm, it can be used in aisles and confined spaces. The lifting arm is extendable in 4 different positions. Hfedpfogypgdsx Agfef

Condition: good (used), Year of construction: 1993, Load capacity: 1500 kg. Loading height: 1800 mm. Width: 2300 mm. Height: 2200 mm. Depth: 900 mm. Hsdpfx Agox Hqhfofjff Weight: 140 kg. Condition: good, second-hand

Condition: used, functionality: fully functional, Used Schenck Balancing Machine H 50 V/B with used CAB 690 H measuring unit. (Can be upgraded to a new CAB 920 unit for an additional (18 000–20 000€) The machine comes with original foundation drawings, documentation and manuals. The machine can be test run in Kerava. Rotor Capacity - Rotor weight range: 20 – 6 000 kg - Maximum symmetrical load on pedestal bearing: 7 500 kg - Maximum symmetrical load on stand bearing: 3 750 kg - The machine can be loaded freely with lower weights when following recommended procedures. - Maximum rotor length between pedestals:1 600 mm (belt drive) - Maximum diameter over machine base: 2 100 mm - Clamped rotor diameter ranges: 25–180 mm, 180–380 mm - Machine bed length: 3 500 mm - Balancing speed n depends on the rotor’s moment and must be selected to avoid overloading the drive. - Maximum permissible G·n² value: 1400 × 10⁶ kg/min² - Applies to a rigid symmetrical rotor mounted on pedestal bearings. - May be exceeded during dynamic tests on flexible rotors and strength tests. Hfjdpfx Asx Ein Sjgfef - End drive / FU motor: 7,5 kW - 4-speed gearbox: 120–2520 rpm - Belt drive BU 5 / FU: 7,5 kW - Unbalance Umar 0,5 gmm/kg: 0 gmm/plane

Condition: as good as new (ex-display), Year of construction: 2023, functionality: fully functional, travel distance X-axis: 820 mm, travel distance Y-axis: 550 mm, travel distance Z-axis: 500 mm, Equipment: chip conveyor, General Control: Max 5 Year of manufacture: 2023 Working Area Travel X: 820 mm Travel Y: 550 mm Travel Z: 500 mm Travel B: +110° / -110° Travel C: 360° Tool changer: 60 stations Rapid traverse X/Y/Z: 36 / 36 / 36 m/min Spindle Speed: 12,000 rpm Power: 16 kW Tool holder: SK40 NC Rotary Table Clamping surface L x W: 600 x 600 mm Spindle nose to table: 150 - 650 mm Table load capacity: 350 kg Equipment Chip conveyor Coolant supply Direct path measuring system Through-spindle air 5-axis simultaneous capability Hjdpfx Ajyap Tfegfjff Workpiece measurement Tool measurement High-pressure coolant (IKZ)

Condition: like new (used), Year of construction: 2013, functionality: fully functional, Weiler Praktikant VCD Precision Lathe Manufacturer: Weiler Model: Praktikant VCD Precision Lathe Year of manufacture: 2013 Condition: used, very good, as-new condition, no signs of wear, incl. new servicing and measurement protocol prior to sale Centre distance: 650 mm Centre height: 160 mm Swing diameter over bed: 320 mm Swing diameter over cross slide: 190 mm Cross slide travel: 150 mm Top slide travel: 110 mm Top slide swivel range: +/-65° Bed slide guide length: 350 mm Bed width: 205 mm Hfsdpfx Asx I Rtkegfof Turning tool cross-section (height x width): 20 x 20 mm Height from top slide to centre: 30 mm Spindle nose according to ISO DIN 702-3 (DIN55027) size 5 Spindle diameter at front bearing: 70 mm Spindle bore: 43 mm Main spindle taper metric 50 Drive power: 6 kW Speed range: 30 – 4000 rpm Number of gear stages: 1 Number of speed ranges: stepless Number of feeds: 24 Longitudinal feed: 0.02 – 0.63 mm/rev Facing feed: 0.006 – 0.2 mm/rev Quill diameter: 40 mm Quill travel: 85 mm Quill taper: 3 Morse taper Weight, without packing and accessories, approx. 1150 kg Length / Width / Height, net: 1720 x 890 x 1700 mm Headstock / rear wall / sliding safety cover: Light grey RAL 7035 Machine base / machine bed: Basalt grey RAL 7012 Screen display housing: Blue NCSS 4550-R80B

Condition: reconditioned (used), Year of construction: 2001, functionality: fully functional, machine/vehicle number: 3595, Ladies and Gentlemen, We are selling a Weiler Commodor B lathe built in 2001 with Heidenhain 3-axis digital readout. The machine has been extensively overhauled in our workshop. Among other things, the main spindle bearing and the lead/traction spindle bearing were completely renewed! Technically, geometrically and visually, the machine is in excellent condition, which you are welcome to see for yourself on site. Availability: on request Machine no. 3595 Year of construction: 2001 Center height: 180mm Center width: 1000mm spindle passage: Ø 56mm max. spindle speed: 2000 rpm Tailstock taper mount: MK4 Feed range: 0.026 - 0.888 mm/rev Possible thread types: Metric, inch, module, diametral pitch Metric thread pitches: 0.35 - 12 mm Spindle brake: switchable Connected load: 4kW Dimensions: approx. 2.2x1.5x1m (LxHxW) Weight: approx. 1.8t Further equipment and accessories: 3-axis digital display, coolant device, chuck guard, pull-out chip tray, 3-jaw chuck Röhm, 4-jaw chuck Röhm, various clamping jaws... Our service promise to you: Hodothd Shepfx Agfjff - We are a certified master company in the field of mechanical engineering - All machines are thoroughly checked - All lubricants and any worn parts are replaced in advance - On request, we can completely or partially overhaul your chosen machine - On request, we can repaint the selected machine in the color of your choice E00f3g2rl - On request, you can also order additional accessories such as tools etc. directly - On request, we can install additional accessories such as safety devices etc. - We are happy to take care of shipping and/or installation

Condition: new, Precision control and lathe Make: OPTiturn Model: TH 4210 Item No.: 3462050 Hfodpfx Aedbgxcegfsf Condition: new machine Tip height: 210 mm Top width: 1,000 mm equipped as standard with: -Machine base -Quad steel holder -Light machine -Reducing bushing MK 6 / MK 4 -2 fixed centres MK 4 -Fixed bezel, 15-105 mm -Bezel running with 10-65 mm -Chuck guard, electrically protected -Coolant system -Change gears set -Oil -Control tool -Manual