CNC Roll Grinder Waldrich Siegen

WaldrichSiegen

Condition: used, grinding diameter / mm Kjdezgipxjpfx Abnsdr grinding length 4000 mm swing diameter / mm

Condition: new, functionality: fully functional, Year of construction: 2026, roller (bottom) diameter: 310 mm, roller (top) diameter: 320 mm, roller diameter: 310 mm, roller length: 1,550 mm, working width: 1,500 mm, sheet thickness steel (max.): 38 mm, overall weight: 12,500 kg, total length: 4,500 mm, total width: 2,300 mm, total height: 1,740 mm, power: 18.39 kW (25.00 HP), working length: 1,500 mm, Equipment: documentation/manual, emergency stop, FACCIN HAV 15342 variable three-roll bending machine Electronically controlled, hydraulic three-roll bending machine Technical data: Number of rollers: Three Geometry of the side rollers: variable Working width: 1550 mm Top roller diameter: 320 mm Side roller diameter: 310 mm Pressure force against the top roller: 160 tons Kdjdpfet Akt Rjx Abnjr Working pressure at nominal force: 250 bar Guaranteed installed power: 18 kW (25 hp) Guaranteed maximum rotation speed: 3.5-7 m/min Guaranteed machine weight: 12,500 kg Length: 4,500 mm Width: 2,300 mm Height: 1,700 mm Guaranteed performance: for material with yield strength 260 N/mm² Rolling capacity (full working width) 38 mm Bending capacity (full working width) 20 mm from pipe diameter 1,600 mm Rolling capacity (full working width) 30 mm Bending capacity (full working width) 17 mm from pipe diameter 415 mm Standard equipment: Variable geometry with linear guides for roller movement Extra long folding bearing for increased frame stability Electronic parallelism system EPS Hardened rollers for high wear protection All rollers ground after heat treatment Siemens S7-HMI PLC control system PGS-CLASSIC control system with Siemens touch panel Hitech hydraulic and electrical package Simultaneous rotation and roller movement Safety ripcord with emergency stop and CE certification Central lubrication Water cooling for the hydraulics Cone bending device Prepared for retrofitting of supports and roller conveyors FACCIN Advantage Package AP

Year of construction: 1953, condition: ready for operation (used), Offered for sale is a WaldrichSiegen CNC portal milling machine for horizontal and vertical milling as well as drilling of large workpieces. Table travel: 14000mm, crossrail saddle travel: 4500mm, crossrail travel: 4000mm, quill travel: 450mm, positioning accuracy of table/crossrail saddle/crossrail/quill: 0.05mm, distance between columns: 4545mm, distance from table to spindle: 4000mm, table size/clamping surface X/Y: 14000mm/4350mm, main spindle motor power: 125kW, main spindle tool interface: ISO SK60, max. table load: 200t, max. point load: 10000kg, control: Siemens 840D, measuring systems: Heidenhain, axis drives: Siemens/Dornhoff. Including an angle-adjustable universal milling head, angle milling heads with installation heights of 800mm/850mm/1400mm, a 1400mm work spindle extension, adapter plates for the work spindle with 400mm/220mm and chip conveyors on the left/right below floor level. The saddle guideways require adjustment. The machine was built in 1953, conversion of the original planer into a portal milling machine by WaldrichSiegen with a completely new milling saddle: 1974, CNC upgrade with a new electrical system: 2001, conversion of the table drive to NC: 2015, conversion of the crossrail drive to a gantry configuration: 2024. Machine dimensions X/Y/Z: approx. 40000mm/10000mm/9000mm, weight: approx. 350t. Documentation available. Inspection possible by arrangement. Kdedpozrzphsfx Abnor

Condition: ready for operation (used), Year of construction: 2024, functionality: fully functional, Gantry Portal Milling Machine / Manufacturer: WALDRICH SIEGEN Type: PF-S-150 - 1953: Original year of manufacture (originally a workbench) - 1974: Reconstruction by the manufacturer WALDRICH SIEGEN to a portal milling machine (completely new milling support) - 2001: Modernised to CNC, with new electrical control cabinet - 2015: Modernization / Reconstruction to NC table drive - 2024: Reconstruction to crossbeam drive (gantry) Machining options: - Milling/Boring: horizontal/vertical The machine can be inspected by appointment under power. Condition: Ready for operation. TECHNICAL DATA / DESCRIPTION: Travel distances of feed axes (CNC): - Table: 14.000 mm - Crossbeam support: 4.500 mm - Crossbeam: 4.000 mm - Stand passage: width 4.545 mm - Clear width: 4.200 mm - Height from table to spindle: 4.000 mm - Quill: 450 mm Kdedsyz Ru Ujpfx Abnsr - Table size / clamping: 14.000 x 4.350 mm - Table load: max. 200 tons (10 tons point load) - Drive power of main spindle motor: 125 kW - Total machine weight: approx. 350 tons - Space requirement for entire machine: Length 40 / Width 10 / Height above floor 9 m EQUIPMENT / ACCESSORIES: - CNC control: SINUMERIK 840D - Documentation - Additional comprehensive equipment ... No guarantee is given for the completeness and accuracy of the technical information and equipment. - Subject to prior sale - Detailed technical data sheet and information on equipment available on request.

Condition: used, grinding length 1000 mm Kdedpfju Dn Txox Abnjr grinding width 300 mm workpiece height 230 mm table surface area 1000 x 240 mm x-travel 1000 mm y-travel 270 mm z-travel 350 mm grinding wheel diameter 240 mm grinding spindle speed 2180 U/min table speed -stepless- 3 - 30 m/min total power requirement 4,5 kW weight of the machine ca. 2,8 t dimensions of machine L x W x H 2,36 x 1,37 x 2,0 m Accessories: magnetic plate 680 x 200 mm, grinding wheel with flange (ø 240 x 25 mm), wet grinding attachment

Condition: good (used), Center height: 1,000 mm Distance between centers: 15,600 mm Maximum diameter allowed above the bed: 2,019 mm Maximum diameter allowed above the carriage: 1,625 mm Diameter of the faceplate: 1,800 mm Maximum clamping between chucks: 1,500 mm Maximum load: 75 tons Spindle motor power: 82 Approximate dimensions: Length = 21,570 mm, Width = 4,765 mm Kedpfx Abezbt S Ienodr Accelerated carriage travel: 2,000 mm/min Metric thread possibilities: from 2 to 25 mm Maximum thread length: 800 mm Minimum distance from faceplate to tool: 2,000 mm Accessories: 2 faceplates with a diameter of 1,100 mm on a traveling steady rest 2 steady rests, 150 to 450 mm 2 steady rests, 450 to 750 mm 2 steady rests, 750 to 1,000 mm (on a traveling steady rest) Videos available.

Condition: good (used), travel distance X-axis: 12,000 mm, travel distance Y-axis: 7,300 mm, travel distance Z-axis: 3,000 mm, total length: 30,000 mm, table length: 12,000 mm, table width: 4,730 mm, total width: 12,000 mm, total height: 10,475 mm, table load: 250,000 kg, overall weight: 400,000 kg, Make : Waldrich - Siegen - Typ : PF-F-150(1)-530/400 - No. : 11.093/0 - Age : Overhault 2004 ( Euro 2.2 Mil) X Travel : 12.000 - Y Travel : 7.300 - Z Travel : 3.000 - W Travel : 4.000 - Between column : 5.000 - Table width : 4.730 Kedpfsytrxkjx Abnodr - Table length : 12.000 - Table load : 19 t / mtr. Ca. 250 ton - Table feed : 10.000 mm/min. - W axis : 3.000 mm/min. - T axis : 6.000 mm/min. - Cross adj. milling head : - Vert. adj. cross rail : - Horizontal hydrostatic spindle ram - Milling spindle Ø : 560 - Milling tool taper : iso 60 - C axis feed : 5.000 mm/min. - Milling motor : 90 kW - Spindle speed : 2.500 R/pm - Z axis stroke : 3.000 - Z axis feed : 2.000 mm/min. - Milling Küma Angle head WF2 90 kw- 450 - Milling Küma Uni. UB1D 60 kw - 2400 - Milling Küma Fixed GB1D 90 kw- 2400 - Milling Küma Angle head WF1? - Electric requirement : 3 x 400 V / 50 Hz - Power requirement : 600 kVA / 630 Amp - Capacity 4.000 L coolant true spindle 20/40 Bar Machine is rebuild in 2004 by Schiess Bed – Table assembly group: * Renewal of sliding lining * Grinding of guideway * Renewal of table drive * Direct linear measuring syst. * Hydrostatic Portal and cross rail: * Modification of adjusting spindle trape Zoidal spindle was recplaced with ball screw * Direct linear measuring syst. * New drive motors for relization of higer speed on feed axes of milling support. * New milling support with hydrostatic guideways Electric system: * Complet elctric cabinet switchgear * Complet new wire * Siemens Sinumrik 840 D in 6 axis !! Equipment / parts : * Complet new raumag janich covers * Complet new double chip conveyor * Complet with big tooling packet * Complet with big mounting equipment - Under power in Europe - Free directly - Controlled axis X / Y / Z / W / C / B axis - Over all height : 10.475 mm - Over all width : 11.934 mm - Over all length : 30.000 mm - Total weight : ca. 400.000 Kg Rebuild in 2004 for EUR 2.200.000 !This CNC Waldrich Portal milling machines was used in the Energie Field for steam turbien case machining. Please Note: The information on this page has been obtained to the best of our ability and belief, and from the manufacturers where possible. It is given in good faith, but its accuracy can not be guaranteed. Accordingly, it will not form a representation or constitute contractual terms. We advise you to check any vital details!

Condition: used, Year of construction: 1987, pressure 160 t chamfer lenght 4000 mm distance between columns 3060 mm control FORTRON CNC 10 H 4 throat 280 mm stroke 250 mm dayligth 500 mm Kdjdpfx Ajtqqr Robnjr table length 4050 mm table width 280 mm feed down 70 mm/sec feed up 68,4 mm/sec working feed 9 / 3,5 mm/sec operating pressure max. 205 bar oil volume 400 l total power requirement 19,5 kW weight of the machine ca. 20,8 t Total weight including accessories 22 t dimensions of machine L x W x H 4,8 x 1,88 x 2,93 m dimensions of switch cabinet 1,6 x 0,5 x 2,25 m - 3-axis machine - Acc.: programmable back gauge, upper and lower dies, table extensions

Condition: good (used), Year of construction: 2012, grinding width: 2,000 mm, workpiece weight (max.): 18,000 kg, grinding length: 8,000 mm, Manufacturer: Waldrich Coburg Type: 30-10 S 3640 Control system: SIEMENS 840D Year of construction: 2012 Guideway / Slide way / Surface Grinding Machine Universal grinding head S10 with 110 Degree tilting / 2500 Rpm / 7.5 kW Vertical grinding head S30 with Ø 600 x 150 / 930 Rpm / 22 kW Double SIEMENS 840D Control panel Left & Right side machine KNOLL HL650/4000 Filtration system new 2023 Automatic doors (4x) for easy machine / load / clamping acces Hydraulic table drive with 18000 kg work load Rebuild in 2012 for 1.5 Mil EUR Large package flanches and stones Large package spare parts / ballscrews / measuring / protection covers Specifications Metric US Standard X - axis 8825 mm Y - axis 3010 mm Z - axis 2500 mm Table length 8000 mm Table width 1800 mm Table load 18000 Feed X - axis 1 - 45.000 mm/min. Feed Z-axis 100 - 3000 mm/min. Grinding stone dimensions Kdedpfx Abotp T N Tonsr 600 x 150 mm Power output 22 kW Rotational speed 930 rpm Coolant system Knoll 4000 L Feed Y - axis 1 - 700 mm/min. Dimensions (estimate) length 24360 mm width 9550 mm height 7000 mm weight 80200 kg Please note: The information on this page has been obtained from the manufacturer to the best of our knowledge and belief, and where possible, the information is given in good faith but accuracy cannot be guaranteed. Accordingly, it does not constitute a representation or contract and we recommend that you check all relevant details.

Condition: like new (used), Year of construction: 2009, functionality: fully functional, We are selling this grinding machine, which is connected and available for testing. Machine parameters: - Grinding of rotational parts clamped between centers with an accuracy of 0.001 mm - Max. swing diameter: 0–1,450 mm - Max. turning length: 6,000 mm - Max. workpiece weight: 20,000 kg (25,000 kg with steady rests) - Grinding wheel diameter: 915 mm - Wheel width: 100 mm - Non-contact measurement of dimensions, tolerances, and workpiece geometry, including printout of measurement protocol - 100% ultrasonic measurement possible - CNC control with capability for profile grinding (taper, concave and convex, CVC) - Grinding of ceramic and metallic coatings using diamond and ceramic grinding wheels Kedpfxoxxrzzs Abnedr The machine is currently completing an order.

Year of construction: 1980, condition: good (used), A used, very well-maintained cycle-controlled lathe from Weisser Heilbronn with a SIEMENS control system. Distance between centers 2000 mm Center height 295 mm Swinging diameter over bed 600 mm Swinging diameter over cross slide 260 mm Swinging diameter in the crotch 800 mm Total length of the crotch 375 mm Bed width 450 mm Travel of X-axis 350 mm Travel of Z-axis 1850 mm Spindle nose DIN 55022, size 8 Spindle speed, number 18, 14 – 1400 rpm Spindle bore 71.5 mm Diameter of front bearing 110 mm Feed range 0.01 – 40.95 mm/rev Rapid traverse 8 m/min DC drive 15 kW 400V 50Hz Max. permissible torque on the spindle 2500 Nm Tailstock quill 80 mm Quill stroke 250 mm Internal taper in quill MK 5 Length x width x height Machine weight 5500 kg Accessories: Tailstock Pneumatic three-jaw chuck with replaceable jaws, 315 mm Quick-change tool holder "MULTIFIX" in front of the center, size "C" Four-position turret behind the center Tool holder Coolant system Follow rest, pneumatically actuated Ksdpfxjgyy I Aj Abnsdr Technical data and dimensions: Subject to change without notice. Video conference via WhatsApp possible after scheduling an appointment.

Condition: excellent (used), Year of construction: 1962, machine/vehicle number: 12.178, 🛠️ WALDRICH SIEGEN WS IIa 100/25 x 5000 CNC roll grinding machine – The perfect base for a retrofit! Get your hands on a high-quality roll grinding machine from WALDRICH SIEGEN – renowned for its exceptional stability and precision in heavy-duty applications. The machine was converted to CNC by Herkules in 1996 and is in excellent mechanical condition. ⚠️ Important – but your opportunity! The machine is currently not operational as the electrical equipment and CNC control system need to be replaced. 👉 Your advantage: Take advantage of this opportunity for a bespoke retrofit and get state-of-the-art technology at a fraction of the cost of a new machine. 💰 📊 Technical highlights 🔩 Grinding diameter up to 1,200 mm 📏 Length up to 5,000 mm ⚖️ Workpieces up to 25 tonnes ⚙️ Grinding wheel up to 900 mm Ø 🚀 Drive power up to 97.5 kW 🎯 Precision up to 0.001 mm 🧰 Features 🔄 Cylindrical & crown grinding 🖥️ CNC grinding support 🔁 Automatic feed with wear compensation 🎨 Partially modernised & repainted 💡 Why this machine? Kedpfx Aofbb D Debnodr ✅ Solid industrial quality ✅ Perfect for modernisation / retrofitting ✅ Ideal for large roller machining ✅ Significantly cheaper than comparable new machines 👀 Viewing available at any time! Flexible appointment available 📅

Condition: good (used), Year of construction: 1982, machine/vehicle number: 11.239, 🛠️ Heavy-Duty Portal Milling Machine WALDRICH SIEGEN Type V/H-FR A heavy-duty and powerful portal milling machine from WALDRICH SIEGEN is offered for sale, ideally suited for machining large and heavy workpieces. The machine comes from a renowned German manufacturer and impresses with its extremely robust construction, high base precision, and excellent suitability for modernization. 💡 Special Feature The machine is sold as-is (not overhauled) and therefore offers an ideal opportunity for customer-specific modernization (e.g. new CNC control, electrics, measuring systems) – perfect for buyers who want to implement their own solution. ⚙️ Highlights ✅ Portal design with fixed cross rail for maximum rigidity ✅ High performance: 58 kW main drive ✅ Speed range up to 1,800 rpm Kdedpfodkmihex Abnsr ✅ Two machine tables with automatic coupling ✅ Extremely high load capacity up to 100 tons ✅ Ideal for retrofit / CNC upgrade ✅ Perfect for heavy-duty machining 📊 Technical Data 🔹 Clamping surface per table: 2,500 x 4,000 mm 🔹 Clamping surface (coupled): 2,500 x 8,700 mm 🔹 Max. workpiece weight: ➡️ per table: 50 t ➡️ coupled: 100 t 🔹 X-axis travel: up to 9,503 mm 🔹 Y-axis travel: 5,515 mm 🔹 Z-axis travel (ram): 1,000 mm 🔹 Spindle power: 58 kW 🧰 Equipment ✔️ Tool changer (chain magazine, 60 positions) ✔️ Angle heads (RAA), including universal angle head ✔️ Spindle extension ✔️ Chip conveyor ✔️ Automatic accessory changing system 📍 Location Germany 👁️ Inspection Inspection possible at any time by appointment 📦 Availability Available at short notice 📩 Contact Contact us now for further information, pictures, or a customized offer!

Condition: reconditioned (used), machine/vehicle number: 550-235-ELD, GENERAL CHARACTERISTICS workpiece Ø max. 41 mm Range Module máx/min. 1,5 / 0.39 Kdjdpfod Nw Ttsx Abnor Rack face width 92 mm Manufacturing No. 550-235-ELD Máx/min. pitch form 20/40-32/64 Maximum stroke of tools trolley 760 mm Rack length máx. 610 mm ELECTRICAL CHARACTERISTICS Main motor power 15 Cv

Year of construction: 2003, condition: good (used), functionality: fully functional, Horizontal machining center with hydrostatic guides X, Y, Z for highest precision TECHNICAL DETAILS X-travel: 2000 mm Y-way: 1250 mm Z-path: 1400 mm speed: 20 - 5.000 rpm torque: 750 Nm tool holder: HSK 100 control: SIEMENS 840D tool changing device: 60 positions Pallet size: 1250 x 1250 mm spindle: 20 kW rapid traverse X-Y-Z: 18 m/min table load: 3 / 5 t Kjdpfjpdqrhox Abnodr MACHINE DETAILS machine weight: approx. 15 t Space requirement: approx. 10.5 x 8.5 x 4.1 m EQUIPMENT NC rotary table 2-fold pallet storage Control panel for loading station IKZ 3D measuring probe Chip conveyor Packing for international transport is exclusive! EXW provision is also possible.