Steady rests 2 pieces 500 diameter

VDF WOHLENBERG P-Turn

Condition: new, empty load weight: 17,500 kg, maximum load weight: 43,500 kg, overall weight: 61,000 kg, axle configuration: 3 axles, loading space length: 7,550 mm, loading space width: 2,750 mm, loading space height: 400 mm, tire size: 245/70 R 17.5, color: grey, Equipment: ABS, Gooseneck: -Gooseneck in SNT design to optimize the loading area length, length approx. 3,750 mm -Gooseneck can be raised/lowered and lowered hydraulically -For tractor units: 6x4 or 8x4 Drop deck: -Low bed with external beams in extendable design, "SUPER LOW" design, length approx. 7,550 mm -Low bed with solid hardwood floor approx. 40 mm thick and mechanical locking mechanism The supply lines are protected in the pull-out supports and automatically adjust to the respective drop-down bed length Rear chassis: -Rear chassis with closed outer frame, checker plate covering and continuous Prisma excavator trough approx. 1,450/900 x 505 mm, open at the rear -2 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame Axles and tires: -"PENDEL-AXLE", all axles with hydromechanical forced steering -Hose rupture valve on the axle compensation cylinder with automatic RESET function -Hydraulic cylinder with stopcocks and locking pin for securing in raised position -Technical axle load: 12,000 kg -Hydraulic axle compensation -245/70 R 17.5 / 3PMSF tires Accessories included: Rsdpfx Ash Hm Thjn Aet -Preparation for mounting bolt-on container positioners for 1x 20ft or 1x 40ft container on the outer beams -2" kingpin -One galvanized steel end wall approx. 400 mm high -One spare wheel with holder -Yellow-red air couplings on the galvanized connection strip at the front -4 wheel chocks -Steering can be operated from the front and rear by remote control cable via pushbuttons, with axle tracking control -Hydraulic connections from the gooseneck to the low bed with multi-coupling instead of screw coupling -Electric hydraulic unit -White reflector tape in accordance with EU regulations on the side, on the extension and red at the rear -2 wooden blocks 500x250x200 mm -European reflector plates (red/yellow) at the rear of the trailer -On the gooseneck and on the rear plate on the left and right, one holder each for the warning signs including socket -Central lubrication system with 2 BEKAMAX (Pico) pumps with NLGI-2 standard grease -Load manometer for determining the axle loads including load diagram -ALU drop sides and rear wall can be plugged onto the gooseneck approx. 2,000 x 400 mm -The rear galvanized stanchions are removable (length of the body approx. 2,120 mm) -Separate air connection with air gun on the gooseneck -Duomatic air coupling from gooseneck to low bed -Gooseneck closed in the rear upper area with a removable cover -1 pair of steel ramps for bridging the mounting hooks of the low bed -Four warning panels approx. 423 x 423 mm, extendable by approx. 400 mm -Radio remote control for steering in addition to the cable remote control, with indicator lights on the receiver for tracking control 6 pairs of threaded blocks between the lashing rings under the top chord on the outer beam for mounting screw-on RUD rings VLBG-4 -7 pairs of stanchion pockets for 100 x 50 mm stanchions in the outer frame of the cargo bed -folding extensions, approx. 230 mm on each side -A layer of sand painted onto the loading surface to prevent slipping Dipper arm recess of the rear chassis closed at the front and rear with a plug-in plate -HRM metallization (High Resistance Metallization) of the outer frame -Complete steel construction shot-blasted, then the defined visible surfaces hot-finished with ZINACOR 850 metallization (zinc 85% - aluminium 15%)

Condition: used, Year of construction: 1996, functionality: fully functional, turning diameter: 710 mm, turning length: 3,000 mm, Universal lathe FAT Poland Model: TUR 710 x 3000 Year of manufacture: 1996 Accessories: Digital readout Rsdsxxm A Hspfx An Ajt 3-jaw chuck Tool holder Steadies Live centre

Year of construction: 2000, condition: used, x-travel 1000 mm y-travel 1600 mm z-travel 800 mm Control WENZEL WPC 2040/FW31.351 Rodpfx Aet Hw Nyjn Aot total power requirement kW weight of the machine ca. 5500 kg dimensions of the machine ca. m Coordinate measuring m/c, software QUARTIS R12/16, Renishaw PH10Mplus

Condition: excellent (used), Herringbone Gear Generator MDV 2000 MDV 2000 Characteristics: Max wheel diameter: 2000 mm Min wheel diameter: 50 mm Max module: 12 Rodpfx Asfx Ibnsn Ast Min module: 3

Condition: used, Year of construction: 1998, Technical details: turning diameter over bed: 600 mm turning diameter over support: 400 mm turning length: 2000 mm center height over support: 300 mm centre distance: 1600 mm revolution per minute: 3 - 2.500 U/min tailstock taper MT: MK 5 Rjdpfxsw Rkt Is An Ast spindle bore of work spindle: 62 mm quill stroke: 190 mm longitudinal feeds:: ca.0,001-10 einstellbar mm/U cross feed: ca. 0,001-5 einstellbar mm/U Rapid feed X axis: bis zu 5000 m/min. total power requirement: 40 KVA weight of the machine ca.: 5,6 t dimension machine xH: 4,0 x 2,0 x 1,9 m incl. accessories see picture *

Condition: used, Year of construction: 2009, greates pass round over bed 1050 mm dist. between centers 6000 mm centre height 520 mm Rjdpfx Anjygxy Us Aet turning length 4810 mm workpiece weight max. (main spindle) 6000 kg Maximum workpiece weight with steady rests 8000 kg max. torque on the spindle 12500 Nm number of spindle speeds 2,8-560 1/min feed per revolution 0,08-56 mm chuck diameter 630 mm Maximum travel distance of the longitudinal slide 4810 mm Maximum travel distance of the cross slide (suppor 530 mm Maximum travel distance of the tool slide (support 340 mm Tailstock quill diameter 150 mm total power requirement 31 kVA weight of the machine ca. 10500 kg dimensions of the machine ca. 7860 x 1970 x 1480 mm Equipment/accessories: -2 x face plates -3 jaw chucks -2 x steady rests -Multifix holder -Turning tools -Various tips -Technical documentation

Condition: good (used), Year of construction: 2006, 1 used 4-axis horizontal machining center Brand Haas Type EC 1600 Year of manufacture 2006 Travel ranges X-axis 1626 mm Y-axis 1270 mm Z-axis 813 mm Spindle centerline to table 304 mm Spindle SK 50 Max. rated power 22.4 kW Max. speed 7500 rpm Max. torque 460.0 Nm 700 rpm Rsdpfjv N Di Ajx An Aot Table size Length 1626 mm Width 914 mm T-slot width 16.00 mm T-slot center-to-center distance 125 mm Number of T-slots in standard configuration: 7 Max. load capacity on table (evenly distributed) 4536 kg Integrated 4-axis (B-axis) Table 1626 mm x 813 mm mm Clamping surface diameter 762 mm Adjustability 360° Max. workpiece swing diameter 1270 mm Table load 4536.0 kg Max. rated power 3.7 kW Rotational torque (continuous) 2712 Nm Backlash 30 arc-sec Gear ratio 500:1 Braking torque 5423 Nm Minimum resolution 0.001° Indexing accuracy ± 30 arc-sec Repeatability 15 arc-sec Rapid traverse rate on B axis 36°/sec Max. feed rate for machining on B axis 36°/sec Spindle centerline to table 146 mm Max. feed rate for machining in x, y, and z axes 12.7 m/min Rapid traverse rate on X axis 15.2 m/min Rapid traverse rate on Y axis 15.2 m/min Rapid traverse at Z 15.2 m/min Axis motors 30-station tool changer Max. tool diameter (full) 102 mm Max. tool diameter (adjacent positions empty) 254 mm Max. tool length 508 mm Max. tool weight 13.6 kg Tool-to-tool (average) 8.00 s Chip-to-chip (average) 12.60 s General information Coolant tank capacity 360 L Dimensions Domestic pallet 488 cm x 366 cm x 346 cm Export crate 488 cm x 366 cm x 348 cm Weight 13608.0 kg

Condition: new, Due to its dynamics and efficiency, the Jantar is the most frequently chosen model of Eckert machines. It is used by large industrial companies and medium-sized businesses looking for both an economical and reliable solution. The Jantar plasma cutting machine can be equipped with a plasma and oxyfuel cutting system and a wide range of accessories. (marking, drilling and machining of tubes and profiles). The design of the machine has been optimized over the years for maximum reliability, as confirmed by hundreds of customers throughout Europe. Main features -attractive price of a very well equipped basic version -Highly dynamic and precise cutting of 2D applications, tubes and profiles -cutting capacity from 0,5mm to 100mm material thickness -Comprehensive database with predefined cutting parameters Rjdpfxsf Alb As An Aet -Possibility to optionally extend the length of the working area Technical data Drive Servo AC Available working widths 1.500, 2.000, 2.500, 3.000 mm Available working length Any length from 1.500 mm positioning speed 25,000 mm/min cutting thickness up to 100 mm Cutting quality DIN-EN ISO 9013 Positioning accuracy DIN-EN 28206 Repeat accuracy DIN-EN 28206 Electrical systems DIN-EN 81346 Safety module DIN-EN 13850 Working height 740-760 mm Working - ambient temperature + 5 °C to 45 °C Working - Humidity max. 90%

Condition: ready for operation (used), Year of construction: 2001, spindle motor power: 45,000 W, total height: 2,120 mm, overall weight: 11,500 kg, controller manufacturer: SIEMENS, controller model: 810 D, product length (max.): 5,400 mm, number of axes: 2, This Weiler E120x3000 was manufactured in 2001. It features a center distance of 3000 mm, center height of 600 mm, and a swing diameter over bed of 1200 mm. The spindle bore is 165 mm, and it offers a robust main drive with a power of 45/37 kW. Ideal for heavy-duty turning, this machine includes accessories like a lathe chuck, faceplate, and a steady rest. Contact us for more information about this machine. • Working area: • Center distance: 3000 mm • Center height: 600 mm • Swing diameter over bed: 1200 mm • Swing diameter over cross slide: 830 mm • Cross slide travel: 590 mm • Bed slide guide length: 860 mm • Turning tool cross-section (H x W): 40 x 40 mm • Tool holder: Parat size 4 • Turning spindle: • Spindle head DIN 55027 / 55026, size 15 • Spindle bore: 165 mm • Main spindle taper: metric 171 • Main drive: • Drive power (60% / 100% ED): 45 / 37 kW • Max. spindle torque: 8000 Nm • Speed range gear stage 1: 1–280 rpm • Speed range gear stage 2: 4–900 rpm • Tailstock: • Quill diameter: 140 mm • Quill stroke: 300 mm • Quill internal taper: MK 6 • Machine dimensions and weight: • Overall length: 5400 mm (without chip conveyor), 6535 mm (with chip conveyor) • Overall width: 2600 mm Rjdpsx D Hz Tefx An Aot • Overall height: 2120 mm • Machine weight: 11,500 kg • Overhaul services: • Hardening and grinding of all bed guides • Grinding of tailstock guides • Overhaul of the complete bed and cross slide assembly (grinding/scraping all guideways) • Renewal of the bed slide's sliding lining • Renewal or relining of the keyways and bottom guides • Renewal of all wipers • Replacement of all belts • Overhaul of the main spindle assembly in the headstock • Renewal of the X-axis including bearings • Renewal of the Z-axis including bearings • Overhaul of the tailstock quill (MK 6 taper regrinding), replacement of spindle and nut • Adjustment of the tooling system • Replacement of the main spindle motor • Checking of the auxiliary motors (X- and Z-axis) • Overhaul of existing safety devices (sliding hood/jaw guard) • Replacement of all rotary, toggle, and limit switches • Replacement of the spindle and handwheel encoder • Replacement of the movable cables and coolant hoses in the work area • Replacement of the central lubrication unit • Renewal of the energy chains • Painting according to specifications (standard textured basalt and light gray) • Assembly and geometric inspection of the machine according to DIN 8605 Additional equipment • 1x used lathe chuck Ø630 mm with various jaws • 1x used faceplate Ø1100 • 1x used steady rest, max. Ø300 • 1x used chip conveyor

Condition: used, number of spindles 4 bore capacity in steel (diameter) 23 mm bore stroke 150 mm total power requirement kW weight of the machine ca. t dimensions of the machine ca. m Rsdpfx Ajt Hw U Non Ast