Interchangeable jaws, 11 sets

SCHUNK KM-WB 41

Condition: new, 900 mm 900 mm 900x900 mm saw band length 9300 x 67 x 1,1 mm table height 790 mm band speed 14 - 60 m/min total power requirement 11 kW weight of the machine ca. 8,45 t dimensions 4,485 x 1,68 x 3,15 m The semi-automatic, hydraulic saws from the X-tech line offer the best Saw technology and best performance when cutting special steels • The electro-welded machine frame and the steel saw frame meet requirements all cutting needs and eliminate vibration and noise. • The chip conveyor is hydraulically driven and the speed is adjustable • All movements of the machine (saw frame, vice, feed, Saw band guides) are carried out thanks to modern linear guides with high static and dynamic load performance, which also has very low sliding friction to guarantee. • Another characteristic feature is the roles for the Positioning of the material by a hydraulic motor are driven. They move at right angles to the material, and thus allowing optimal clamping of the material. • Thanks to the height control of the saw band position, the operator can place the band in place near the top edge of the material. After the cut is finished, the tape automatically raised back to the previous position. Alternatively you can also “Remain” can be selected in the lower position. During the The software compares the cutting load with the cutting cycle Default. This means that the sawing system can be stopped in the event of irregularities become. • The saw band is cleaned by two adjustable steel brushes. The drive takes place hydraulically. • The hydraulic unit including filter and pressure gauge guarantees one particularly quiet operation at constant pressure. • Finely ground carbide inserts that clamp the saw blade, complete with lateral, hardened and adjustable guide rollers. The adjustable one The tape guide automatically moves as close as possible to the material. Hsdsfg E Hpjpfx Adajh • The saw band is tensioned via a hydraulic cylinder, which is carried out by the Machine software is controlled. The voltage is set according to a given Time automatically delimbed when the machine is idle or after a cycle has been carried out. • Automatic version with CNC control in the X-TECH 900 / 1200 models a feed length of 500 mm for the series for high production rates. • The material is carried by a table with seven rollers. These will driven by a hydraulic orbital motor through which the material can be placed precisely even under maximum load. • All guided movements are carried out by four recirculating ball guides with one high capacity for static and dynamic loading; strong reduced feed friction. Tempered and ground prismatic Guides. Price on request.

Condition: new, Year of construction: 2025, saw band length: 3,920 mm, saw band width: 34 mm, Double column bandsaw fully automatic Everising H-260 HB Hsdpfx Adjq Ulxysash Cutting range round: 0 - 260mm Cutting range square: 300 x 260mm Bundle tension: Width: 145 - 190mm Bundle tension height: 30 - 130mm Drive power: 3.7 kW Saw blade dimensions: 3920 x 34 x 1.1mm Weight: 1759 KG Machine dimensions: 2170 x 2100mm The standard equipment of the machines is as follows: Solid steel construction in double column principle - NC feed system - Frequency-controlled cutting speed (infinitely variable, inverter-controlled) - Digital cutting speed display - Hydraulically controlled double horizontal clamping vices - Hydraulic saw band tensioning - Saw band guides (incl. band back guide) made of carbide - Hydraulically pre-tensioned band guides - Precise PLC control (SPS) for all hydraulic and electrical components. - Cutting counter with automatic switch-off - Automatic out-of-stock switch-off - Multi-job function - Bundle clamping device - Driven chip brush - Automatic belt breakage control incl. emergency stop - Chip flushing gun - Flexible work light - 2 meter roller conveyor - Tool box - Carbide function Special equipment included: - Variable clamping pressure reduction - Cutting process control Extensive complete German documentation.

Condition: new, turning diameter over bed 410 mm Hsdpfsm Rlb Nex Adajh turning diameter over slide rest 240 mm turning length 1000 mm turning diameter in the gap 530 mm turning speeds 65 - 1810 U/min centre height 205 mm spindle bore 52 mm tailstock quill taper MT 4 total power requirement 2,2 kW weight of the machine ca. 0,9 t dimensions of the machine ca. 1,9 x 0,8 x 1,3 m Center lathe with: 3-axis digital measuring system fully assembled electromagnetic main spindle brake auto. Feed in longitudinal and transverse direction safety relay Micrometer end stop coolant device 3-jaw lathe chuck with 1 set of turning and drilling jaws German operating instructions.

Condition: new, capacity 90 degrees: round 510 mm capacity 90 degrees: square 450 mm 650x450 band speed 15 - 100 m/min table height 844 mm dimensions of saw-band 5320 x 34 x 1,1 mm total power requirement 3,0 kW weight of the machine ca. 2,1 t dimensions of the machine ca. 1,9 x 2,87 x 1,3 m PROMOTIONAL PRICE!!! 2-column double miter band saw K-tech DG 62/45 HA-I • 2-column miter saw • Solid, yet easy to use • Material height sensor (automatic cut start detection) • Smooth running thanks to diagonal cutting, feed regulator + cutting pressure regulator • Solid material inlet roller • Removable chip tray (disinfection) • Energy-saving and low-vibration thanks to diagonal cutting • Control panel ergonomic, safe and free-standing • Frequency-controlled saw drive 15 -100 m/min. • Hydraulic cutting pressure control valve Hodpfod Iipmsx Adaoh • Hydraulic control of saw frame and vice • LEDs for monitoring all safety functions • Large-sized wheels (520 mm) a. • Clear miter adjustment up to 60° Semi-automatic function: 1. Tension the material 2. Saw starts 3. Lowering in rapid traverse to the beginning of the material or the same for series cutting cut 4. Saw blade off 5. Raise the frame until it is just above the material 6. Vice opens

Condition: new, Comparable to Behringer, Kaltenbach, Kasto, Jaespa, etc. Hjdpfxjh Tnd Ae Adaeh Cutting range 90° Round: 260 mm Flat: 300 x 260 mm Smallest diameter: 5 mm NC-controlled, automatic material feed with hydraulic full-stroke material clamping Easy operation via NC control with plain text display Material advance function without reclamping for short section cuts Robust, linear-guided feed gripper with servo positioning for maximum precision Automatic adjustment of blade guides to material width Recommended options: Powered chip brush synchronized with blade speed Separate control panel 7" CE panel, network-compatible, up to 1000 data sets storable, history memory for various functions and data, etc.

Year of construction: 2006, condition: refurbished (used), HYDRAULIC PRESS MECAMAQ PRESSURE 350t STROKE 350mm TABLE LEFT RIGHT 600mm TABLE FRONT BACK 750mm POWER 15kw Dimensions: Hedpfx Adjfmqqlsajh Height: 2,9m Width: 1,9m Length: 1,3m Weight: 5.700 kgr

Condition: used, Technical details: number of controlled axis: 6 workpiece weight: 20 t operating time: 4290 h control: YASKAWA total power requirement: 35 kVA Total weight, approx.: 2000 kg dimensions L x W x H: Roboterschweißanlage: 2,7 x 1,1 x 2,0 m dimensions electric cabinet: L:700 x B:800 x H:2000 mm Robot specifications: Hedpfxeu Nwfbe Adajh -6 different directions of movement -payload max. 20kg -working curves: turning curve=1717mm, turning height=1417mm; turning width=2072mm -rotation axis arm: S-axis rotate=+/-180°, L-axis lower arm=+1550° / -110°; U-axis upper arm=+255° / -165° -rotational axes wrist: R-axis roll=+/-200°, B-axis pitch-swivel=+230° / -50°, T-axis rotate=+/-360° -rotational axis speed: S-axis and L-axis = 170°/s; U-axis 175°/s; R-axis and B-axis 355°/s; T-axis 525°/s -permissible torques: R-axis and B-axis=39.2 Nm; T-axis 19.6 Nm Welding equipment specifications: -Fronius, TIG welding, (DC and AC), 3 A/10.1 V - 300 A/22.0 V, water cooling, IP23 protection class. Table top unit specifications: -Table support Ø 600mm, rotate 360°, swivel 90° each right/left. Details of the wire feeder: -Fronius, type KD 7000, feed 0,2 - 22m/min., protection IP23, voltage U1 230V Manual control unit Control cabinet i.D. *

Year of construction: 2021, condition: new, TECHNICAL DATA type: gas-heated drive-through chamber furnace Hedpfeg Dgymjx Adajh internal dimensions: (w x h x d): 2200 x 2350 x 3000 mm number of control areas: 2 Max. loading weight: approx. 2,5 t PLC: Siemens S7

Condition: used, L-TEC Inverter TIG Welding Machine Type Inverter TIG 200 DC TIG welding machine for direct current (DC) Serial No. 184548 Year of manufacture: approx. 1994 Output: 200 amps = 60% duty cycle 155 amps = 100% duty cycle Adjustment range: infinitely variable Current type: DC (direct current) Mains connection: 400 Volt, 50 Hz, 32 Amp plug - 4-meter hose package with central connection and hand torch - with remote potentiometer (foot switch) - gas pressure regulator Hjdodzqb Eopfx Adash - DC only - HF ignition Space required (L x W x H): 850 x 480 x 740 mm Weight: approx. 150 kg The welding test shows very good results when welding stainless steel with direct current. Overall in good condition.

Year of construction: 1983, condition: good (used), Machine number: 316204/22 Type / Model: FSS 315/E Travel x-y-z: 850 - 280 - 355 mm table: 1.200 x 370 mm clamping surface: 1.060 x 260 mm Speed range: 28 to 1,400 rpm spindle mount: SK 50 quill stroke: 80 mm Feed rates x and y axis 16 to 800 mm/min feed z-axis: 5 to 250 mm/min Connection: 8 kW Accessories/equipment: Swivel head; Hjdpfx Asfli Afjdaeh condition: good Weight: 4 t Dimensions: 2.000 x 2.000 x 2.400 mm