Cutting Mill

Rapid 3026 1999

Condition: new, Year of construction: 2024, Gold River SWZ-700 water separators Application description: The GOLD RIVER SWZ series separator has been designed for special tasks, it can cope with the most difficult materials that contain many properties that disturb the separation process in separators commonly available on the market. SWZ water separators separate heavy fractions (non-ferrous metals) from, among others, plastics in the process of recycling secondary raw materials. SWZ separator equipped with a four-section copper water system equipped with radial nozzles with variable linear geometry. The separator uses the latest divided type of separation mat. The development of a modern module for preliminary division and preparation of material guarantees the purity of recovered raw materials in a very short time (plastics, metals). Why a water system? Our device uses a system similar to that used in the gold recovery industry. We use water as a carrier and a force that affects the materials in a gentle way. In the water system, all particles with higher mass are gently washed out and separated, generating no losses during the entire separation process. The properties of water together with our proprietary solutions are unrivaled compared to, for example, air separators. SWZ type separators are used: Separation of heavy from light materials (metal granulates contaminated with plastic, foil, paper, cotton, fibers) Cleaning plastics after air separators (dry) Separation of metals in cable and non-ferrous metal recycling lines Gedpfx Aeua Tbwjh Eebw The SWZ-700 water separator, thanks to the use of the latest module, performs the separation process in a very short time, therefore it is characterized by a high hourly efficiency of separated material of approximately 1200 kg/h. Description of action: The material fed into the separator goes through the transport channel to the module for initial fraction division into its mass and humidity changes. Some of the material is separated at this stage. In the second part of the module, the humidity of the remaining batch changes. Then the material falls onto the separation table where the final fraction separation takes place. As a result of this process, we obtain valuable materials from both sides of the separator. Construction description: The massive structure and the inertial drive of the separator are made of materials appropriately selected to withstand the overloads resulting from vibrations. The supporting frame ensures excellent stiffness and failure-free operation for many years. Due to the type of vibration drive, the design does not require the installation of a soil separator. Separation table equipped with hydraulic adjustment of the angle of inclination. The separation table has a special module for initial division of fractions into their mass and preparation for final separation. The water system has several water pressure valves. The water circulation in the separator is closed. There is no need for constant access to an external water source because the device works using the water already in the tanks. Based on experience and continuous research in our laboratories. We are able to provide you with separators individually adapted to the specific nature of the material being separated. In various versions and sizes. SWZ-700 separators are manufactured to individual order.

Condition: used, Year of construction: 1985, 1x Used MOCO AZ-8 Shredder Drive power: 7.5 kW Gbjdpfx Aozx Svxeh Eow

Year of construction: 2013, condition: used, functionality: fully functional, Tomra Halo 1500 (Titan 60") for sale. The machine is currently in use in a potatoe packhouse in Germany and will become available June/July 2026. Prior delivery, the machine will undergo a service and througough cleaning in our workshop, including the replacement of broken fingers, infeed conveyor as well as the hedgehog band. Gedpfx Ahsx A Ebpj Eobw

Condition: new, Year of construction: 2026, Extremely powerful industrial magnet for iron separation Special price: €990 net (shipping €14.90 net) *Construction lengths can be found in image 2 Godpfxjtqfhxs Ah Eobw The active side is equipped with a stainless steel end plate (material 1.4301). Threaded holes are provided on the rear side for mounting; *handle available on request The block magnet systems can be used at temperatures of up to max. +100°C operating temperature. The magnet surface should be cleaned regularly from captured iron parts. Pickup distances for all types, for example: For a steel nut M5: approx. 60 mm For an M5 x 30 screw: approx. 100 mm Mounting example 1: Mounted above a conveyor belt, 'iron parts jump onto the holding surface of the magnet.' Mounting example 2: Mounted within a pipeline system with direct contact to the material flow. For maximum separation safety, a cascade setup of multiple block magnets in series is possible. Assembly and safety instructions: When handling, already upon unpacking and later during installation, ensure that there are no loose iron parts, such as tools or screws, nearby. The magnetic force is so strong that painful injuries may occur if fingers get caught between iron parts and the active surface. There should be no steel parts under the active surface within a minimum distance of 400 mm.

Condition: ready for operation (used), functionality: fully functional, CES Coolbox 3-Fans shock freezer cabinet for connection to Co2 fluid. Maximum trolley size 120 x 115 x Hight 215 cm. Gsdeydpnqjpfx Ah Ejbw

Condition: good (used), Used Thermocontainer Item no. C785ü In revised and repaired condition, Basic cleaning carried out, visually in good condition inside – see photos Ready for immediate use Our offer is aimed at commercial customers; We kindly request that private inquiries be avoided. Inspection is expressly offered with signs of wear (C785ü) Technical data Interior: 610 x 810 x 1570 mm Exterior: 735 x 955 x 1900 mm Weight: approx. 98 kg Capacity in liters: approx. 785 With rails for cooling plates Features Locking mechanism in the center of the door 2 side pull handles 1 folding handle in the door recess Rolling chassis with 108 mm wheels, PA, suitable for cold storage Door latch Interior tub with sliding rails Angled corner supports with bent edges PE sheets (2 mm thickness), light blue Profiled deflector plates (3-sided) 2 fixed wheels, 2 swivel wheels Can be locked with a padlock Load capacity up to approx. 400 kg From a company liquidation, REVISED Thorough cleaning is to be carried out by the buyer Color may vary depending on stock levels Approx. 100 units in stock We offer the possibility of inspection on Tuesdays and Thursdays between 9 am and 4 pm, by prior telephone appointment. If required, the item can be taken away immediately. Unless explicitly stated otherwise, this offer refers to used goods. The items have been visually inspected and are technically in order. Shelves and cooling plates are not included in the offer. However, these are also available from us. Due to time constraints, we can only provide answers to questions about this item if you provide us with a telephone number in your inquiry. Gbsdpsk I Hbyefx Ah Eew If you would like the item to be shipped, please contact us to discuss packaging and shipping costs. (Photos are similar, as we do not depict every individual item)

Condition: used, We offer a compressor package containing a mix of Dorin, DWM, Frascold, and Prestcold units. This package has been assembled for trade and export purposes and is available from 5,000 kg per package (larger packages available upon request). Fixed price: This package is sold at one fixed package price. No individual sales. The price does not depend on the quantity per brand; it is simply: 1 package = 1 fixed price. Gbsdpfoycqglsx Ah Ejw

Condition: good (used), Cold water set, cooling water circuit, heat exchanger, cooling for spot welding device, spot welding machine, spot welding system, spot welding tongs -Chiller: complete refrigeration unit -Compressor: Danfoss type: MTZ22JC4A Gbedpfslpi Tqsx Ah Esw -Pump: Lowara type CEA70/5 0.55 kW -Total dimensions: 740/710/H930 mm -Weight: 196 kg

Condition: excellent (used), Your contacts within our company: Mr. Andre Evering Mr. Marcel Brahms Mr. Simon Blank We are offering you a used pallet racking crossbeam from the manufacturer Nedcon for sale. Technical data for the pallet racking crossbeam: Racking system: Nedcon Type: NS Currently available: approx. 5,000 pieces The scope of delivery includes: 01x Pallet racking crossbeams, used Material color: RAL 2008 Light Red-Orange Box profile: 90 x 40 mm Hook type: 4 hooks Gbjdpfxjd A Sm Te Ah Eow Clear width: 1,900 mm Max. load per pair of crossbeams: 2,000 kg, with evenly distributed load 02x Locking pins, used Design: fully galvanized For securing the longitudinal supports against accidental lifting out Our services at a glance: (Prices on request) Assembly, installation Our general assembly conditions apply Racking inspection Racking inspection according to DIN EN 15635, carried out according to the requirements of BGR 234, visual inspection for all racking systems Delivery with our own fleet (without unloading)

Condition: used, Complete set condensing Unit Rivacold with 1 compressor Copeland Scroll ZF24 for a freezing room with a capacity of 80 to 120 m3, Rivacold condensing unit -Compressor type: ZF24KVE-TWD -Cooling capacity: 20.4 kW at -5°C/40°C, 17.5 kW at -10°C/40°C, 10.7 kW at -25°C/40°C -Dimensions: 1750 x 1000 x 1500 mm -Number of fans: 2 x 500 mm Evaporator Rivacold -Type: RX50338 -Cooling capacity: 8 kW -Fin spacing: 8 mm -Electric defrost Gbjdjz A Rybepfx Ah Eew -Dimensions: 1750 x 570 x 460 -Number of fans: 3 x 350 mm