Milling Device

PFAUTER Fraeskopf - Innenverzahnung

Condition: good (used), Year of construction: 2000, gear diameter: 449 mm, Equipped with: Fanuc 150MB CNC Control Dry Cutting Cutter Shroud Chip Evacuation System Auto Doors Hydraulic System Lubrication System Work light Stack Light Specifications: Largest Speed Ratio: 10:01 Work Area (Continuous): Largest Depth of Teeth: 15.24 mm Largest Width of Tooth Face: 50.8 mm Work Area Axis: Horizontal Movement X Axis: -114 - 178 mm Vertical Movement Y Axis: -178 - 190 mm Movement of the Carriage Baseplate Z-Axis: -10.16 - 500 mm Workpiece Headstock Swiveling Range B-Axis: -3 - 90 Degree Maximum Distance Machine Center to Spindle Side: 165 mm Number of Teeth: 5-200 Inclusive Max. Gear Pitch Dia. of Typical 35 Deg. Spiral Angle Gear Using Max. Cutter Dia. 12" Cutter at the Following Ratios: Face Milling 1 x 1 - 13.5" - 342.9mm 2 x 1 - 16.0" - 406.4mm 5 x 1 - 17.7" - 450.0mm Face Hobbing (210mm Dia. Cutter) 1 x 1 - 10.560" - 268.22mm 2 x 1 - 10.286" - 275.00mm 5 x 1 - 11.810" - 300.00mm Milling Head Diameter: Helixact: 100,125,169,200,250,320mm Continuous Gumption Procedure, Teichloroethylene: 102 - 210 mm Workpiece Spindle: Drilling of Large Diameters: 5 3/64" Cone Upward Gradient on 304.8 mm (1 Foot): 21/32" Deep One of the Cone: 5.29" Diameter of the Whole Spindle Perforating: 3.35" Speeds: B-Axle Workpiece Headstock Drag Axis: 30 Degrees A-Axle Workpiece Spindle Number of Revolutions: 0 83 min-1 X-Axis Horizontal: 80 mm/sec Y-Axis Vertically: 80 mm/sec Hjdpfx Ajruakgef Seu Z-Axis Carriage Baseplate: 80 mm/sec Space Requirement L x W x H (Approximate): 4.75 x 3.40 x 2.54m / 188" x 134" x 100" Machine Weight (Approximate): 10980 kg / 24,156#

Condition: used, Year of construction: 2007, x-travel 900 mm y-travel 300 mm z-travel 1000 mm control Siemens Sinumerik 840D max. workpiece diameter 1600 mm max. module 20 mm tip circle diameter 350 mm Milling arbour diameter 375 mm Total closing value 80 kVa weight of the machine ca. 33,5 t dimensions of the machine ca. 10,530 x 6,375 x 4,680 m Feed rate: - X-axis 1 to 3000 mm/min - Y-axis 1 to 3000 mm/min - Z-axis 1 to 4000 mm/min Spindle speeds in rpm: - Tool 26 to 265 - Workpiece table 0 to 8 Hjdow Rrb Hjpfx Af Ssu Equipment/accessories: - M 2 motor milling head - Milling mandrels - Oil cooler - Technical documentation

Condition: used, Year of construction: 2024, Overview The bottle washer was previously used in a brewery. Due to the low number of operating hours, the machine is in very good condition, like new. It was replaced, as the previous owner wanted to run bottle formats, which did not fit this machine. All basins and the machine body are made of stainless steel. The machine is already disassembled and dry stored, so that it can be easily loaded and transported. The machine comes with 12months warrantee. Tech Specs: - Capacity: 9,500 bph - Cell Pitch: 95 mm - Bottles per row: 25 - Dimensions + Weights: Housing: 7,162 x 2,740 x 2,500 mm / 18,806 kg Ready for operation with attachments: 7,162 x 3,540 x 2,730 mm / 31,563 kg - YOM 2024 - Formats: - 0,25l - 0,33l - 0,5l - 0,75l The Machine in Detail / Equipment Features: - Heated by steam - Pre Cleaning and removal of residual liquids by pulsed rinsing prior to washing Hjdpfx Afjvrfivo Sju - CE certified - Chemical Dosing Pumps - Machine data sheet included - High pressure pre rinsing - Rotating Spray nozzles - Single End Machine - Label discharge rear right - Finger discharge + finger feed - Bottle cells made of plastic - Concentration measurement - NaOH supply liquid - Sectional view arrangement of baths - Spindles SST - 24 volt control voltage - Control Siemens S7 - Regularly maintained - Full machine body in SST - Vapor Discharge - Machine dismantled, ready to ship - Automated machine Startup

Year of construction: 2011, condition: new, functionality: fully functional, lifting height: 6,000 mm, main lifting speed: 9,000 mm/min, Electric cable hoist i=28 New in original packaging as a parts carrier or for installation, see pictures Hodpfxjvylhbe Af Ssu GDR3 H12 Motor ZBR100 B4 B050

Condition: excellent (used), Year of construction: 2008, Siemens Sinumerik 840 D, 5 axes controlled. Wheel diameter max 2000 mm 700 mm wheel width Machine weight 35,000 kg Space requirements approx. 6.9 x 8.4 x 3.7 m Hjdpfxeza Egbs Af Seu

Condition: excellent (used), Year of construction: 2008, 300 kg load capacity welding rotary table, with hollow shaft diameter 125 mm Hjdpfx Afslamtbo Seu with chuck 320 mm or 400 mm very robust speed continuously adjustable from 0.15 to 5.0 RPM current transfer 350 A rotary table diameter 400 mm tilting up to 135° height in horizontal position 835 mm, when tilted up to the center approximately 735 mm length 850 mm x width 580 mm

Condition: good (used), Year of construction: 1976, max. wheel diameter 1250 mm gear width 1000 mm max. module 16 shifting 250 mm milling spindle speeds (infinitely variable) 32 - 200 U/min min. number of teeth 12 table hole 255 mm total power requirement 32 kW weight of the machine ca. 20 t dimensions of the machine ca. 5,1 x 3,2 x 3,7 m Top condition! Hedpfx Ajzr Rpksf Seu 2 cut cycle, change gears, arbors, chip conveyor. Following hob arbors are with the machine: Diameter: 32 , 40 , 50 , 60 mm

Condition: new, Year of construction: 2024, Welding positioner with a 1000 kg load capacity with manual and foot-operated remote control Diameter 1000 mm Bore diameter 100 mm Height 580 mm Hedpfx Afsgfqkwe Sju Variable speed 0 - 0.6 RPM AC 380 V motor

Condition: used, Year of construction: 2012, Control Siemens 840 D weight of the machine ca. 13,5 t dimensions of the machine ca. 7m x 4m x 2,75m m Hodpoxh Rqtjfx Af Ssu Accessories: Coolant tank Grinding wheels Various spare parts Operating and maintenance instructions CE conformity Dimensions: 7x4x2.75 m ( LxWxH) TECHNICAL DATA: Workpiece data: max. outer diameter: 250 mm with max. grinding wheels Ø 450 mm max. diameter to be machined over table: 375 mm Profile depth for dressable grinding wheels: 40 mm max. workpiece length: 3,600 mm max. distance between centers (1): 2,800 mm max. bevel angle: +/- 90° Number of teeth of the workpiece: 1 - 999 max. weight of the workpiece: 250 kg Working area: Center distance between workpiece and tool spindle: 355-170 mm Radial travel: 185 mm Axial travel: 3,000 mm Swivel angle: +/- 90°

Condition: good (used), Year of construction: 1976, max. wheel diameter 2300 mm gear width 1000 mm Hsdpjzr Rpdsfx Af Ssu max. module 22 min. module 1 total power requirement 45 kW weight of the machine ca. 22 t dimensions of the machine ca. 5x3x4 m