Used Traub for sale (94)

Year of construction: 1986, condition: ready for operation (used), Turning diameter over bed/face slide: 360mm/160mm, center distance: 800mm, travel X/Z: 205mm/810mm, speed: 3150rpm, spindle bore: 60mm, tool positions: 8, rapid traverse X/Z: 10m/min. Machine dimensions X/Y/Z: approx. 3300mm/1800mm/1800mm, weight: approx. 3300kg, control: Traub System TX-8. An on-site inspection is possible. Ledpfx Abowmqx Ds Uohn

Condition: ready for operation (used), Year of construction: 2000, operating hours: 22,232 h, functionality: fully functional, machine/vehicle number: 317, turning length: 1,000 mm, turning diameter: 680 mm, spindle motor power: 60,000 W, spindle speed (max.): 2,800 rpm, Equipment: chip conveyor, TECHNICAL DETAILS Turning length: 1,000 mm Turning diameter: 680 mm Spindle motor power: 60,000 W Max. spindle speed: 2,800 rpm MACHINE DETAILS Control model: TX 8H Electrical Data Operating voltage: 400 V 3~ Control voltage: 24 V ~ Solenoid voltage: 24 V – Clutch voltage: 24 V – Total power: 60 kW Total current: 100 A Ljdpfxew Rp Svo Ab Uohn Spindle operating hours: 22,232 hours EQUIPMENT Documentation/Manual Continuously adjustable speed Chip conveyor RUEZ SFWW2 Oil separator Tool holder VDI40 Comprehensive documentation Note: Dismantling and loading can be supported with personnel and crane facility.

Condition: used, Year of construction: 2005, turning diameter 275 mm turning length 900 mm control TRAUB TX8i spindle passage 65 mm power capacity at 100 % load 25,20 kW power capacity at 40 % load 30,20 KW max. torque at 40% / 100% load 180 / 135 Nm spindle turning speed - stepless 1 - 5.000 U/min spindle diameter in front bearing 110 mm C-axis 1 - 500 U/min worktool support No. 1 x-axis 290 mm y-axis 165 mm z-axis 600/950 mm B - axis 360 ° rapid traverse X/Y/Z 18 / 18 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN number of tools 2x2 + 2x2 number of driven tools 2x2 + 2x2 mm toolpiece turning speed range 8.000 / 2.000 U/min power capacity at 25 % load 5,80 kW Lodpfjw E Nnbox Ab Uohn max. torque at 25% load 4x18,6 / 4x74 Nm tool taper TRAUB Ø60 worktool support No.2 / No.3 / No.4 x-axis 170 mm z-axis 600/950 mm y-axis +/- 60 mm rapid traverse X/Y/Z 18 / 15 / 30 m/min feed capacity X/Y/Z 10 / 10 / 7 kN tool turret - number of stations 10 number of driven tools 10 mm toolpiece turning speed range 1 - 6.000 U/min power capacity at 25 % load 5,80 kW max. torque at 25% load 18,60 Nm tool taper DIN 69880 Ø40x63 bar loader DNH61 / 3000 Bar length 1.000 - 3.200 mm bar material dia. 18 - 63 mm hexagon max.45 mm total power requirement 95,00 kW weight of the machine ca. 16,00 t dimensions of the machine ca. 10,00 x 3,50 x H3,00 m With TRAUB TX 8i control unit, main and counter spindle with C-axis, 3 turrets, 1 vertical-tool-carrier with B-axis, dust exhauster, chip conveyor, coolant system with coalescence-separator. Barfeeder TRAUB Stamag DNH61 /3000 2 pc. 3-jaw chuck SMW KNCS-N 170-43 2 pc. HAINBUCH Spanntop chuck 40 pc. various tool holder non-driven 6 pc various tool holder driven Spare parts package

Condition: good (used), Year of construction: 2005, operating hours: 60,764 h, functionality: fully functional, machine/vehicle number: 6030637, The machine is in good, ready-to-use condition and can currently be inspected under power. Disassembly and removal of the machine are the buyer’s responsibility. The machine features 2 turrets, each with 12 tool stations, all of which are driven. There is also a front station with 5 tool positions, 4 of them driven, as well as a rear station with 5 tool positions, 4 of them driven. The main spindle clamping system is a Hainbuch 32; the sub-spindle features an Axfix clamping system from Hainbuch. Various basic tool holders are included. Lhjdpfx Abew N Rzio Uen

Condition: new, 3 safety windows suitable for CNC lathe TRAUB TNA 300 TNA 400 TNA 500 TNC 42 TNC 65 Lhodpsw Edq Defx Ab Uon Size: 660 x 480 mm Price: €500.00 / unit net Delivery time: immediately, subject to prior sale Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 DE - 44143 Dortmund - Wambel

Condition: ready for operation (used), Year of construction: 1993, functionality: fully functional, machine/vehicle number: 364, controller model: Traub TX8F, number of axes: 7, Equipment: bar feeder, chip conveyor, CNC lathe with 7 axes, bar feeder & additional equipment! TECHNICAL DETAILS Bar length: 3000 mm Number of axes: 7 Control: Traub TX8F MACHINE DETAILS Spindle 1 operating hours: 50,318 h Spindle 2 operating hours: 32,922 h EQUIPMENT Main spindle Counter spindle 2 turrets 2x C-axis 1x Y-axis Bar feeder: IEMCA CNC BOSS 542 Lhodpsw Ec Alsfx Ab Ujn Enclosure Coolant system Chip conveyor

Year of construction: 1983, condition: ready for operation (used), Turning diameter: 320mm, turning length: 1000mm, spindle clearance: 80mm, speed: 3150rpm, travel X/Z: 265mm/1000mm. Machine dimensions X/Y/Z: approx. 5500mm/2400mm/2400mm, weight: approx. 7000kg, control: Traub System TX-8. Including a tool set, three-jaw chuck and bar chuck with collets. Documentation available. On-site inspection is possible. Lhsdpswzld Dsfx Ab Ujn

Condition: excellent (used), CNC machine Traub TNL 26 Condition used, in good condition Sale to the exclusion of any warranty Lodpfx Aohlp Sdsb Uohn

Condition: used, Year of construction: 1987, control Traub System TX 8D swing diameter over longitudinal slide 660 mm swing over plan sled 445 mm turning length 1000 mm spindle passage 80 mm spindle tunring speed 2.000 U/min number of tool places 14 Pos. chucking diameter 250/315 mm Number of working hours ca. 39794 h Ljdpfxjv Ig D Ts Ab Ushn In our opinion, the machine is in good used condition and can be inspected under power by appointment. Accessories, tools and clamping devices shown are only included in the scope of delivery if this is noted in the additional information. Subject to changes and errors in the technical data and information as well as prior sale!

Condition: used, Year of construction: 1990, turning diameter 250 mm turning length 450 mm control TX8D bore 80 mm spindle speed: 3150 U/min. CNC Lathe with Bar Feed and 3 Turrets Very large spindle bore, with bar loading device Lhedpfx Ast Hwq Djb Usn Please ask for further details.

Condition: good (used), Year of construction: 1990, Manufacturer: Traub, model TNS 60, control unit: TX8-D, operating hours: 2,321, serial no.: 1407, year of manufacture: 1990 Lhedpfx Abow Hdwgj Uon FROM TRAINING WORKSHOP

Condition: good (used), Machining diameter max: 36 mm Maximum spindle speed: 6300 rpm No. of Spindles: 2 Controller: Traub TX8i Toolchanger 1: No. of tools: 12 positions X-axis travel: 50 mm Z-axis travel: 50 mm Toolchanger fronside: Lhsdpfstrvzxex Ab Usn No. of tools: 7 positions Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 370 mm Z-axis travel: 250 mm Toolchanger backside: No. of tools: 5 Speeds: 150 - 3000 Rpm 300 - 6000 Rpm Max. diameter: 40 mm X-axis travel: 73 mm Barfeeder: FMB Turbo 5-42 Barlength: 3200 mm Bardiameter: 5 - 42 mm Country of origin: Germany Machine LxWxH: 3400 x 1300 x 1700 mm Machine weight: 4000 kg

Year of construction: 1993, condition: ready for operation (used), A Traub universal CNC lathe is available. Swing diameter over bed/slide: 400mm/360mm, turning diameter maximum/normal: 360mm/320mm, max. turning length: 1000mm, center distance: 2000mm, chuck diameter: 315mm. Spindle bearing diameter: 160mm, spindle bore: 80mm, speed: 4000rpm, power: 26kW, tool positions: 14, travel X/Z: 180mm/1000mm, feed: 24mm/rev, rapid traverse X/Z: 1000mm/1500mm/min. Quill diameter: 100mm, quill stroke: 200mm. Machine dimensions X/Y/Z: approx. 5800mm/2400mm/2400mm, weight: approx. 7200kg, control: Traub System TX-8-D. Documentation available. On-site inspection is possible. Ledpfowrrq Esx Ab Ushn

Condition: reconditioned (used), Year of construction: 2005, functionality: fully functional, Traub CNC lathe TNC65DGY, TX8I, year 2005, serial no. 1130 Description Y-axis on S1, V-axis, 2x C-axis, 2x rotary tool drive, 2 VDI30 turrets, Hainbuch BZI65 on main and counter spindle, parts gripper, Iemca Master 880MP-E loading magazine, Condition Very well maintained, good condition, serviced. Machine geometry has been checked and corrected/adjusted. Machine can be viewed under power – video available. 6-month warranty on main components as follows: Spindle bearings, ball screws, linear guides, clamping cylinders. Lsdpfx Aowi I Eysb Uehn The warranty expressly applies only to spare parts, not to downtime, labor, or travel time. The warranty expressly does not apply to parts other than those listed above, e.g., wear parts, electrical, electronic, hydraulic, etc.

Condition: good (used), Year of construction: 1999, operating hours: 86,157 h, The machine was built in 1999 and underwent an 8,000-hour maintenance last year. Total operating hours: 86,157 hours. Turret 1 has 14 stations (with Y-axis) Turret 2 has 10 stations (without Y-axis) Ljdpowur N Tofx Ab Uehn

Condition: good (used), Year of construction: 2000, Traub TNL12/7 Lhodjpuilvepfx Ab Uen Spindle passage 12.7mm Turning length 130mm Main spindle 4kW; oś C 0.001 grad; 12.000 rpm Revolver 1 - axis X1 Y1, 6 tools, driven tools 1.5kW Revolver 2 - axis X1 Z2, 6 tools, driven tools 1.5kW Subspindle 2.5kW; axis C 0.001 grad; 12.000 rpm Frontaparat - axis Z3; Z4/X3, driven tools Backparat - axis X4, driven tools 1.5kW Barfeeder FMB Minimag For sale 2 machines, a lot of accesories and toolholders. Machines under power, in production. 1. TNL12/7 s/n: 248 b/y: 2000, (7 linear axes X1, Z1, Y1, X2, Z2, X3, Z3 +2x C axis) + FMB Minimag + Knoll swarf conveyor 2. TNL12/7 s/n: 277 b/y: 2000, full option (9 linear axes X1, Z1, Y1, X2, Z2, X3, Z3 X4, Z4 +2xoś C axis) + IEMCA Genius + Knoll swarf conveyor

Condition: ready for operation (used), Year of construction: 1991, functionality: fully functional, machine/vehicle number: 5318, spindle bore: 26 mm, spindle speed (max.): 4,750 rpm, TECHNICAL DETAILS Lhsdpfx Aewtq Urjb Uen Max round diameter: 26 mm Max square size: 18 mm Max hexagon size: 22 mm Spindle power: 2.2 kW Number of spindles: 4 Spindle bore: 26 mm Speeds: 1,180 – 4,750 rpm Tool holder: 6 slots MACHINE DETAILS Length L -- R: 1,800 mm Width F -- B: 1,000 mm Height: 1,400 mm Weight: 800 kg Total power: 3.2 kW Operating voltage: 380 V 50 Hz

Year of construction: 1996, condition: ready for operation (used), Turning length: 450mm, spindle clearance: 65mm, speed: 4000rpm, main spindle/counter spindle power: 18.5kW/11kW, tool positions: 10, driven tools: 10, hydraulic capacity: 150l, hydraulic pressure: 60bar, connected load: 39kW. Rapid traverse X1/X2: 15m/min, feed force: 5000N, feed path: 140mm. Rapid traverse Z1/Z2: 30m/min, feed force: 8000N, feed path: 450mm. Rapid traverse Y1: 6m/min, feed force: 8000N, feed path: +/-35mm. Machine dimensions X/Y/Z: approx. 4150mm/2000mm/1800mm, weight: approx. 4750kg, control: Traub System TX 8F, operating hours: 78825h. Documentation available. On-site inspection is possible. Lhjdpjv Scrhjfx Ab Uon

Condition: good (used), Year of construction: 2001, functionality: fully functional, Traub CNC Lathe TNC65DGY, TX8H, 2001 • 2x 10-station turrets with VDI30 rotating tool drive • C-axis on main/counter spindle • Y-axis on turret 1 • Hainbuch BZI65 on main/counter spindle Hollow clamping cylinder • Chip conveyor, coolant tank • Spare parts list, circuit diagram, ATC optics Lhodswi Izhjpfx Ab Uon Very good condition. Can be viewed under power. The machine's geometry has been checked and corrected/adjusted.

Condition: like new (used), Year of construction: 2022, operating hours: 13,116 h, Max. bar capacity mm: 20 Max. Z-axis travel (sliding headstock/fixed headstock) mm: 205 / 80 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 C-axis resolution degrees: 0.001 Max. rapid traverse Z m/min: 20 Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 / 8,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Slide travel X mm: 120 / 165 Slide travel Y mm: ±25.4 Slide travel Z mm: 254 / 567.5 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 B-axis swivel angle degrees: 105 Lower turret: Tool stations: 8 Driven tools: 8 Max. tool speed rpm: 12,000 Tool holder diameter mm: 45 Drive power 100%/40% duty cycle kW: 1.0 / 2.0 Turning tool cross-section mm: 16x16 / 20x20 Slide travel X mm: 120 Slide travel Y mm: ±25.4 Slide travel Z mm: 155 Rapid traverse X/Y/Z m/min: 20 / 20 / 40 Back working device: Tool stations: 4 Slide travel X/Y/Z mm: 120 / ±25.4 / 155 Tool holder diameter mm: 25 Sub spindle: Max. spindle bore mm: 20 Max. spindle speed rpm: 10,000 Drive power 100%/40% duty cycle kW: 3.0 / 5.5 Torque 100%/40% duty cycle Nm: 5.73 / 10.5 / max. 17.2 Slide travel X mm: 235.5 Slide travel Z mm: 258 C-axis resolution degrees: 0.001 Rapid traverse X/Z m/min: 20 / 40 Coolant system basic unit: Pump pressure bar: 3 / 8 Tank capacity l: 250 Flow rate at 3 / 8 bar l/min: 80 / 120 Filtration degree µm: 200 Machine dimensions Length x width x height mm: see installation plan* Weight kg: 5,000* Lhjdpfx Abswuddve Ujn Connected load kW: 40 (47 kVA)

Year of construction: 1991, condition: ready for operation (used), A CNC lathe is available. Turning diameter over bed: 450mm, turning length: 630mm, spindle bore: 65mm, speed: 4000rpm, rapid traverse: 15m/min, power: 57kW, travel X/Z: 175mm/630mm, tool positions: 12+8+4, machine dimensions X/Y/Z: approx. 4000mm/2200mm/2200mm, weight: approx. 6500kg, control: Traub System TX-8-D. Documentation available. On-site inspection is possible. Lhodpswxfatsfx Ab Usn

Condition: used, Year of construction: 2011, operating hours: 51,400 h, functionality: fully functional, Traub CNC Lathe TNX65, TX8i-s, Year 2011 Model: TNX 65 Year of manufacture: 2011 Control: TX 8i-s Main/spindle and counter-spindle bar capacity up to 65 mm, 3 turrets, 3 x Y-axis, driven tools, 2 x C-axis, counter spindle, chip conveyor, band filter, coolant system, parts conveyor, new hydraulic pump Lhjdpfxswxc Hke Ab Uon Extensive accessories; approx. 4 driven tool holders, 15 fixed holders Breuning short bar loader Approx. 114,586 power-on hours Approx. 51,400 production hours Good condition Connected to power, available for inspection Delivery time approx. 2 weeks, by arrangement

Year of construction: 2015, condition: ready for operation (used), A CNC double-spindle lathe Traub overhauled in 2025 is available. Turning length: 450mm, spindle clearance: 65mm, speed: 4000rpm, main spindle/counter spindle power: 18.5kW/11kW, tool positions: 10, driven tools: 10, hydraulic capacity: 150l, hydraulic pressure: 60bar, connected load: 39kW. Rapid traverse X1/X2: 15m/min, feed force: 5000N, feed path: 140mm. Rapid traverse Z1/Z2: 30m/min, feed force: 8000N, feed path: 450mm. Rapid traverse Y1: 6m/min, feed force: 8000N, feed path: +/-35mm. Machine dimensions X/Y/Z: approx. 4150mm/2000mm/1800mm, weight: approx. 4750kg, control: Traub System TX 8F, operating hours: 12938h. Including chip conveyor and bar loader LNS Quick Load. Documentation available. On-site inspection is possible. Ljdpfx Abev Scrbe Ujhn

Year of construction: 1991, condition: ready for operation (used), A CNC lathe is available. Turning diameter over bed: 450mm, turning length: 630mm, spindle bore: 65mm, speed: 4000rpm, rapid traverse: 15m/min, power: 57kW, travel X/Z: 175mm/630mm, tool positions: 12+8+4, machine dimensions X/Y/Z: approx. 4000mm/2200mm/2200mm, weight: approx. 6500kg, control: Traub System TX-8-D, operating hours: 19465h. Documentation available. On-site inspection is possible. Lhedpfx Aswxfayob Uon

Year of construction: 1994, operating hours: 38,274 h, condition: ready for operation (used), Spindle clearance: 42mm, turning diameter over face slide/bed: 170/400mm, speed: 56-5600rpm, control: TX 8F. With four driven tools, various tool holders VDI30, high-pressure pump 15bar, measuring arm for tool measurement. Operating hours: 38,274h, Baumüller drive BUH-4-55-6-002 produces an error message and must be overhauled. On-site inspection is possible. Lhjdpfxjq A S Duj Ab Ujn