Used Sheet Metal Hole Punch for sale (40,455)

Condition: good (used), Number of straightening rolls 5 sheet width 430 mm Sheet thickness 1 mm Top roll diameter 2 Top rolls - Ø 60 mm Ibodpfx Asgvl U Rsfisc Bottom rolls diameter 3 Bottom rolls - Ø 60 mm

Condition: used, Radial fan with sheet steel housing, type H15 /400-M, serial no. 27265, year of manufacture 1977. Inlet pipe Ø 200 mm, outlet pipe Ø 110 mm. Airflow rate 0.25 m3/s = 900 m3/h. Total pressure difference 4000 N/m2 = Pg: 400 kg/m2. Specific gas weight at 20°C: 1.2 kg/m3. Maximum temperature range 70°C. Motor speed 2850 rpm. Motor power 2.2 kW. Power supply 400 Volts, 50 Hz. - Sheet steel housing - Sturdy metal base. Required space L x W x H: 740 x 520 x 1540 mm. Weight approx. 80 kg. Good condition. Ibodpfxoxcitvo Afijc

Condition: excellent (used), functionality: fully functional, Year of construction: 1996, working width: 6,000 mm, sheet thickness steel (max.): 3 mm, sheet thickness aluminum (max.): 4 mm, Equipment: documentation/manual, The face design of the segmental machine structure and the swing-mounted bending beam on the kinematic mechanism enable the bending of various complex shapes from steel and aluminum sheet with a maximum bending angle of 145 degrees and a maximum upper beam stroke of 200 mm. The machine is controlled by a three-axis programmable controller, allowing operation in three modes: Manual, single – includes one program consisting of a single bending stage and one backgauge setting, which can be repeated any number of times. The program comprises 60 programmable blocks, each containing 10 bends and backgauge positions. Iodjxflfmopfx Afiebc The machine can bend steel sheet up to 3 mm thick and aluminum up to 4 mm. The hydraulic oil has been replaced and the entire control system has been renewed.

Condition: new, Year of construction: 2025, Roller for sheet metal unfolding. Working width: 1.250mm, loading capacity up to 2 tons and a brake. Ibedpfexd Rgyox Afioc

Year of construction: 2009, condition: ready for operation (used), machine/vehicle number: 527, Offer 23035 Technical data approx: - Pressure capacity 30 T. - max. sheet thickness 10 mm - max. punching diameter 105 mm - punching capacity - e.g. steel sheet : 105 mm in 1,5 mm ; 45 mm in 5 mm - e.g. VA - sheet metal : 90 mm in 1,5 mm ; 45 mm in 4 mm - stroke 7 - 70 mm - throat 560 mm - maximum stroke rate 120 H/min - single stroke / continuous stroke Isdpfx Aelnkc Ujfisbc - drive 400 V / 4 kW - space requirement approx. W 8000 x H 1850 x D 1700 mm - weight approx. 1900 kg - with: - stop table with stops - foot switch; - emergency stop button - punch quick change device - various receptacles for punches and dies

Condition: new, Year of construction: 2025, Automatic roofing sheet forming machine for aluminum or galvanized steel sheet with a sheet width of 1000mm. Includes automatic sheet decoiler, Siemens control system, and technical documentation. Ibedpsw A Rt Hsfx Afisc

Year of construction: 1972, condition: used, Sheet Paper Cutting Machine – Strachan & Henshaw (UK) High-quality industrial machine, manufactured in the United Kingdom, designed for cutting paper rolls into sheets with precise dimensions. Its robust construction and proven reliability make this machine a practical solution for print shops, packaging factories, and other applications in the paper industry. 🔹 Main features: Iodpfx Afsxcxpgoiebc Automatic cutting of paper rolls into sheets; High dimensional accuracy; Operating speed suitable for industrial production; Solid construction, suited for intensive use; Easy maintenance and low operating costs. This 1972 Strachan & Henshaw machine is still operational and represents a reliable and economical choice for producers seeking a durable and efficient unit.

Condition: used, Repair-needing Wide Belt Sander, Surface Grinding Machine, Sheet Metal Deburring Machine, Deburring Machine with 4 Processing Stations Sanding Unit and Brushing Deburring Unit Manufacturer: BÜTFERING - STEELMASTER Type: Frima-V/413RRTT Machine No.: 76 931 Year of Manufacture: 2002 2x Brushing Deburring Units + 2x Sanding Units Max. working width: 1350 mm Conveyor belt width: 1370 mm (heavily worn on the sides) Working thickness: 0.3 mm to 150 mm Sanding Units Abrasive belt dimensions: 1350 mm x length ?? mm Abrasive belt motor (1): 11 kW (speed 2930 rpm) Abrasive belt motor (2): 12.5 - 16 kW (speed 1470 - 2950 rpm) - Abrasive belt speed (belt 1): only at high speed - Abrasive belt speed (belt 2): 2 speed settings - Pneumatic belt tensioning Brushing Deburring Units with multiple vertical sanding discs and oscillation 2 roller brushes Ø 250 mm Roller width: 900 mm Ibsdsw Ed Uvspfx Afioc Brush speed: approx. 1440 rpm Deburr brush motor (3): 7.6 - 9.5 kW Deburr brush motor (4): 7.6 - 9.5 kW - Sanding disc speed (3): 2 speed settings - Sanding disc speed (4): 2 speed settings - Oscillating movement of brush rollers via gear motors - 2 separate drive motors, one for each brushing station Conveyor Feed Unit Conveyor motor power: 0.75 kW - Infinitely variable conveyor speed via frequency converter - Motor-driven height adjustment for material thickness 0.3 - 150 mm Power supply: 400 Volt, 50 Hz, 55 kW Machine footprint: Length 300 x Width 270 x Height 210 cm Required space for transport: Length 600 x Width 242 x Height 210 cm Weight: approx. 5.5 tons The machine was operated with wet grinding; belt filtration system integrated in the machine frame The machine is in poor condition, was taken out of production, and stored under tarpaulin for approx. 5 months. Technically, everything still appears to be in reasonable shape, but improper storage has led to some rust formation. The machine requires refurbishment.

Condition: excellent (used), functionality: fully functional, Year of construction: 2016, machine/vehicle number: 150, power: 400 kW (543.85 HP), overall weight: 1,940 kg, fuel type: electric, MABI 3000 E VARIO cutting machine in excellent working condition. Manufactured in 2016, serviced in June 2025 by a qualified technician, brand new PC fully replaced (invoice available). Cutting machine for parts (duct sections, fittings, bends, boxes, branches, cones, domed end caps, all types of ducts, etc.) Cuts multiple types of alloys (aluminum, stainless steel, etc.) Efficient production of single pieces and/or batches Clean and precise cutting technology for time savings and minimal waste, ideal for SMEs. Loading and transport costs are the responsibility of the buyer. Ibsdpfjxcu Dmsx Afisc (Tip: Plan for a forklift with extended forks (at least 2 meters in length), able to lift at least 4 to 5 tons, for loading and unloading the machine) (Footprint: 2160x2310x2200 mm / Weight: 1940.0 kg)

Condition: repair required (used), Sheet Metal Processing Unit, Decoiler, Straightener, Guillotine Shear, Reinhardt Maschinenbau GmbH Ras 228.60 Used Machine Manufacturer: Reinhardt Maschinenbau GmbH Model: Ras 28.60 Maximum Sheet Width: 1500 mm Maximum Sheet Thickness: 1.5 mm Total Weight: 9350 kg Features: Decoiler Measuring Unit Sheet Straightener Guillotine Shear Electrical Data: Iodpfovkbrqex Afiebc Voltage: 400 V Power: 12 kW Frequency: 50 Hz Current: 35 A Note: The control panel display is not functioning.

Condition: good (used), Year of construction: 1985, machine/vehicle number: 2.309.044, Offer 23195 Precision - deburring - faceting milling machine / edge milling machine Technical data: Steel - stainless steel - aluminum - plastic ,machining deburring and faceting process is done with milling cutter Isdpfx Afsnvdtcsiebc Bevel angle 45 ° bevel width infinitely variable length of guide bar 500 mm working height 750 mm speed 2750 rpm drive 400 V / 0,7 kW space requirement approx. W 500 x D 400 x H 8500 mm Weight approx. 30 kg

Condition: used, Load capacity: 3 t Ibjdpfx Afjb Nwkxjioc Opening width: 38 mm Weight: 15 kg

Condition: used, Pay-off and take-up decoiler for coil material WANZKE CAMU Type SC 515/M Serial no. 8487 Year of manufacture: 2006 Coil weight approx. 1,500 kg Maximum coil width: 600 mm Coil inner diameter: 370 - 640 mm Maximum coil outer diameter: 1,800 mm Mandrel shaft diameter: 90 mm Distance from mandrel crown center to mandrel base: 950 mm Ibedewvv Rqepfx Afisc Mandrel crown speed: 13 rpm Motor speed: 920 rpm Gearbox transmission ratio: 1:70 Mandrel drive motor power: 1.1 kW Power supply: 400 Volt, 50 Hz - Mechanical expansion of the mandrel crown with hand crank - Drive via geared motor with worm gearbox, directly mounted on the mandrel shaft - Geared motor with electric brake - Mandrel shaft with mechanical slip clutch, pre-tensioned and adjustable via disc springs - Mandrel crown without strip travel arms - Without electrical control system and without loop switch Space requirement (L x W x H): 1300 x 800 x 1230 mm Weight: 380 kg Good condition

Year of construction: 1982, condition: good (used), machine/vehicle number: 0155282778711, OFFER 21455 Technical data: - Pressure capacity 450 KN - punches e.g. up to 25 mm Ø in steel 15 mm - stroke infinitely variable 0 to 60 mm Ibjdpfx Afehkr Dasiec - stroke rate approx. 16 to 47 1/min - throat 760 mm - Installation height 215 mm - working height 1150 mm - Drive 400 V / 7,5 kW - Space requirement approx. W 850 x H 1850 x D 1650 mm - Weight approx. 1350 kg - with: - E. foot switch - 20 pieces div. hole punches + dies

Condition: ready for operation (used), Pressure force: 10 tons Projection: 110 mm Ibsdpfxohtq Hfo Afisc Required space: 300 x 170 x 680 mm Weight: 32kg

Condition: used, Hydraulic guillotine shears SAGITA - MANURHIN - License BEYELER Type 2550 x 6 Machine. No. 00682 Year of construction 1980 Cutting length 2520 mm Cutting thickness 6 mm Backgauge 750 mm Cutting angle adjustable Hydraulic pressure max. 290 bar Motor power 11 kW Mains connection 400 Volt, 50 Hz - Back gauge with motorized adjustment and mechanical actual value display, fine positioning via handwheel - Manual cutting gap adjustment - Infinitely variable cutting length adjustment - 11 pieces hydraulic sheet metal hold-down device - front angle fence left 1300 mm Ibodpfst Ac D Uox Afisc - 3 front table extensions 1300 mm - electric foot switch - very solid and torsion-resistant welded construction - 1 set of replacement blades - slightly damaged (blade length 2550 mm) - operating instructions Space requirement with table supports L x W x H 3200 x 2800 x 1600 mm Space required for transportation L x W x H 3200 x 2150 x 1600 mm Weight 6300 kg Good condition

Year of construction: 1998, condition: good (used), machine/vehicle number: 0159488169537, Offer 23293 Technical data: - Pressure capacity 300 KN - punches e.g. up to 30 mm Ø in steel 9 mm Iedpfxepuy H Ds Afijbc - or with special punching device up to 100 mm Ø in steel 2.5 mm - stroke infinitely variable 0 to 28 mm - stroke rate 26 to 36 1/min - throat 610 mm - Installation height 240 mm - Drive 400 V / 4 kW - Space requirement approx. W 750 x H 1650 x D 1350 mm - weight approx. 1300 kg - with: - foot switch - grain search device, - support table with foldable stops W 1100 x D 850mm - shifting distance of the stops from the center of the punch - width between Li and Re approx. 470 mm x D 510 mm

Condition: used, Universal Beading Machine, Border FASTI Type 81504 - UBPB 1.5 Machine No. 828152 001 Year of manufacture: 1982 Sheet thickness max. 1.5 mm Sheet thickness min. 0.5 mm Bead height max. 12 mm Bead height min. 4 mm Feed speed 4 / 8 m/min Roller diameter 60 mm Min. inside bending radius for 90° arc section 100 mm Drive power 1.1 / 1.4 kW Power supply 400 Volt, 50 Hz - Sheet guide - Operating manual (as copy) - The machine’s drive motor does not have an electric brake – the brake is missing Required space (L x W x H): 700 x 610 x 1250 mm Weight: 150 kg Machine operates, but runs on slightly after stopping due to the missing brake, when used without material Iedpfx Afeux Shioisbc

Year of construction: 1970, condition: good (used), machine/vehicle number: FF 16, Offer 22226 Technical data: - Pressure capacity 50 T - throat approx. 360 mm Ibsdpfeit T Hyex Afioc - installation height approx. 240 mm - drive 400 V / 7,5 kW - perforates in ST 40 e.g. up to 25 mm Ø in 16 mm - up to 20 mm Ø in 19 mm - space requirement approx. W 1000 x H 1900 x D 1000 mm - weight approx. 1800 kg

Condition: used, Hydr. guillotine shears SAFAN type VS 310 / 4 Machine. No. B7140 Year of construction 1984 Cutting length 3100 mm Cutting thickness 4 mm Back gauge 900 mm, accuracy +/- 0.5 mm Angle fence front left 2100 mm Hydraulic tank capacity approx. 120 liters Drive power 7.5 kW Mains connection 400 Volt, 50 Hz - Motorized back gauge with positioning control and digital position display - Single stroke and continuous stroke with adjustable stroke pause - Cutting angle adjustment - Manual cutting gap adjustment - stepless cutting length adjustment - Cutting line lighting - 17 Hydraulic sheet hold-down device - Angle stop left with scale 2100 mm Ibsdpfxoumpq Ns Afijc - 2 material support arms 1600 mm - 2 material support arms 615 mm - Electric foot switch - Fixed finger guard in front of the hold-down devices Space requirement without sheet supports L x W x H 3850 x 2300 x 1680 mm Machine depth with sheet supports 3900 mm Weight 5.7 tons good condition

Condition: good (used), Year of construction: 1993, Offer 23481 Technical data: - Pressure capacity 30 T - max. sheet thickness 6 mm - Max. punching diameter 105 mm - stroke 42 mm - throat 700 mm - maximum stroke rate 200 H/min - Table dimensions W 1500 x D 1100 mm - table height 1000 mm - Drive 400 V / 4 kW - Space requirement approx. W 1600 x H 2000 x D 2200 mm - Weight approx. 3400 kg - with: - stop table with adjustable stops - Quick stamp change device - foot switch; Ibjdpfx Afsrgptioiec - Emergency stop button - Various punches + dies in separate workbench

Condition: used, Hydraulic guillotine shears FASTI Type 509 - 25/4 Machine no. No. 5418 Year of construction 1991 Cutting length 2535 mm Cutting thickness 4 mm Backgauge 5-1000 mm (controlled) Cutting angle adjustable Hydraulic pressure max. 290 bar Ijdpfx Afot Apumeiobc Motor power 7.5 kW Mains connection 400 Volt, 50 Hz - Back gauge with positioning control ELGO ELECTRIC type 85 - Sheet holding device under the back gauge - Manual cutting gap adjustment with dial gauge display right and left - stepless cutting length adjustment - Hydraulic cutting angle adjustment via hand pump - front angle stop left 1300 mm - 14 sheet hold-down devices - electric foot switch - very solid and torsion-resistant welded construction - 1 set of original FASTI replacement blades (4 pieces, presumably new and unused) space requirement L x W x H 3100 x 2350 x 1700 mm weight 3500 kg good condition

Condition: good (used), Year of construction: 1991, machine/vehicle number: 0168091277886, Offer 23294 Hydr. combined flat and profile steel shears with notching device and hole punch Ibsdpfx Asrll I Usfiec Technical data: - Flat steel shears - blade length 470 mm - for flat material 450 x 15 mm - or 300 x 20 mm - Profile steel shears - L-steel at 90° 140 x 13 mm - at 45° 70 x 7 mm - T-steel at 90° 70 mm - Steel bar shears - round steel 50 mm - Square steel 42 mm - Notching device - rectangular notching 52 x 90 x 12 mm - Hole punch - Punching force approx. 750 KN - Infinitely variable stroke 0 - 70 mm - punches holes in steel up to 30 mm Ø in 20 mm - throat 310 mm - Hydraulic drive 400 V / 7.5 kW - Space requirement approx. W 1600 x H 1850 x D 1400 mm - Weight approx. 2400 kg - with: - 2 E. foot pedals for two separate work stations - Turntable

Condition: used, Swivel bending machine FASTI Type 2095-25-2,5 Serial no. 94 295 004 Year of construction 1994 effective length 2540 mm max. sheet thickness 2.5 mm Stroke of upper beam 380 mm Motor power bending beam 2.2 kW Iedpfx Aottc Uasfiobc Mains connection 400 Volt, 50 Hz - NC control FASTImatic FM100 - One-piece 135° pointed rail - Controlled backgauge - Continuous stop rail - controlled bending angle via control unit - electric foot switch weight 3000 kg good condition

Condition: used, Hydraulic punch, punch frame for use with JOKA punching units type HP-S Isdpfeltrmusx Afiebc Hydraulic hole punch, hydraulic press for punching brackets Year of manufacture: approx. 1995 Pressing force: 5 tons Throat depth: 155 mm Stroke: approx. 20 mm Punching unit width: max. 54 mm Punching unit installation height: max. 220 mm Die holder: Ø 48 mm Motor output: 1.5 kW Power supply: 230 Volt, 50 Hz - Suitable for universal use with JOKA SW 20 or SWD 20 punching units - Throat depth of punching units can be larger, can be pushed through to the rear - Stroke release via electric two-hand control - Hydraulic power pack HAWE, type HCW 4 / 2.5-B 1/400-1 - On subframe, mobile Required space (L x W x H): 1100 x 800 x 1450 mm Weight: approx. 200 kg Good condition