Used Scm Tech 80 for sale (614)

Condition: used, Year of construction: 2011, Base Machine M800 X5 TV 1 WORKING RANGE X: 5,020 mm Y: 1,830 mm Z: 675 mm Clearance Height: 300 mm (from 50 mm suction cup height) MACHINE STRUCTURE The base structure is a monolithic construction made from thick-walled steel. It is reinforced across the entire machine bed with welded components, providing exceptional stability. The table design, with its large base, is the key to ensuring lasting precision and stability. The machine’s layout enables the operator to achieve optimal workflow with minimal space requirements. The mobile gantry is built as a solid monoblock. It is positioned in the X direction on prismatic, ground guides with recirculating ball carriages. The machining unit is mounted on this mobile support carriage, also on prismatic, ground guides and recirculating ball carriages. AXIS MOVEMENT All axes travel on prismatic linear guides with large cross-section and recirculating ball shoes with a wide contact surface, which ensures optimal sliding, even at high speeds and accelerations. The precise and fast positioning of the movable gantry (X-axis) is achieved via helical rack and pinion. Large cross-section recirculating ball screws ensure accurate positioning of the machining unit along the movable gantry (Y and Z axes). The perfect mechanical dynamics and maximum positioning accuracy are controlled by high-quality drives and brushless motors. Max. axis speeds: · X-axis = 90 m/min · Y-axis = 90 m/min · Z-axis = 30 m/min Safety device with bumper and light barrier 1 Bumpers with sensors are fitted to the movable upright, and a light barrier system is installed at the front of the machine. If the operator enters the active zone, the X-axis travel speed is reduced to a lower value of 25 m/min without stopping the machine. This system allows parts to be loaded during pendulum operation without the limitation of access areas, as seen with pressure mat systems. This prevents unwanted interruptions in the machining cycle and offers greater freedom of movement around the worktable. CE certification for the safety system 1 Safety protection fence 1 Side and rear protection fence Automatic central lubrication controlled via CNC 1 The lubrication of the X, Y, and Z axes is controlled by the CNC; intervals are regulated automatically, without manual intervention. Central extraction connector 1 All individual extraction connections of the machining units are collected into a central extraction port. Inside the port, there are various slider valves controlled by the NC. This reduces the required extraction air volume. Chip conveyor 1 Maxi – 5-axis electrospindle 11 kW HSK-63 “Prisma K 1 5-axis electrospindle, 11 kW at 20,000 rpm S1 (100% duty cycle) Speed: max. 20,000 rpm Rotation direction: left/right Liquid cooling Tool interface HSK 63F Inverter 18 kW, stepless, smooth power delivery Max. rotation B-axis = 200° (+-100°) C-axis = 650° Thanks to the non-orthogonal axes, it is possible to perform complex horizontal positioning in a small workspace. This enables the machining of complex geometries without the risk of collision. Djdpfjxy Tmnjx Ac Nocc

Condition: good (used), Year of construction: 2015, functionality: fully functional, edge thickness (max.): 12 mm, ENGLISH: Heavy duty edgebander OLIMPIC (SCM Group) in rich configuration suitable for custom made and series production. Machine is equipped with aggregates with servomotors (ABS R1+R2mm + thin edge + solidwood). Model: Olimpic K800 TERL Manufacturer: SCM Group Production year: 2015 State: good Edgebanded edges: 238.800 meters Main technical parameters: Djdpowxt Tbjfx Ac Njcc - feeding speed: 12/18 m/min. (including rounding) - panel thickness: 10-60 mm (including rounding) Equipment and configuration of the machine: - control panel with LCD touch screen STARTOUCH - internal lightning of working area - automatic lubrication of the feeding chain - electronic top pressure adjustment - glue pot with quick change of the glue color Working units: - antiadhesiv spray - pre-milling unit (2x DIA cutter) - glue pot with roller "VC/1000" (glue pot with quick-release system) - pressure rollers (4 pcs) with timed intervention - 2 motor end cutting unit "K/SEL" with pneumatic tilting of the blades - radius trimming unit "RI/800" R1mm + thin edges + solid wood (12mm) (3 position pneumatic kit) - 2 motor rounding unit "ROUND K MULTI EDGE" R2mm + thin edge (each motor has: 2 electronic axis with servomotor) - radius edge scrapers "RAS/S 2P" MULTI-EDGE R1+R2mm (each unit has: 2 electronic axis with servomotor) - cleaning spray - glue scrapers "RCA/2C" - brushes"SP/F"

Condition: used, Year of construction: 2016, TECHNICAL DATA AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting working area mm 0 x 800/0 x 800 X axis stroke mm 750 Max. travel speed of X-Y axes m/min 25 DRILLING UNIT Vertical spindles Number 7 (4X-4Y one common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed grooving saw (direction) X Grooving saw diameter mm 100 Max. grooving saw thickness mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Grooving saw speed rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air requirement bar 6 Compressed air consumption Nl/cycle 90 Extraction requirement m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 80+80 F10L Drilling unit Includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with one drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. Diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit. Positioning of the workpiece and drive of the work unit: A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the work unit during machining. Movement in the X and Y axes takes place on THK guides with transmission to reinforced toothed rails. Movement in the Z axis is pneumatically controlled on ball-bushing guides with adjustable stop positioning. The positioning of the work units is carried out using technology and drives with DC motors. CNC CONTROL The control system was specially developed for use in drilling and milling machines. CN - 7" color screen with touchscreen function - Alphanumeric keyboard - Self-diagnosis and any error messages or malfunctions that may occur, in the operator's language Programming - Programming via the CN - Automatic optimization of drilling operations - Option of plate zero point shift - Option of saving and importing drilling programs via USB dongle - Option of importing drilling programs from CAD-CAM external software Configuration - User interface in the same language as the instruction manual Graphic representation of the unit configuration Vacuum suction cups "B-Power Vacuum suction cups with double vacuum connection, recommended for particularly porous panels (e.g. MDF light). Machine user interface software Xilog Maestro USB Hardware and software requirements: - Operating system: Windows XP Professional (SP2), Windows Vista or Windows 7 - Processor: Intel compatible, 2GHz min; Multicore processor recommended - Memory capacity: 1GB min., recommended 2GB - Free disk space: 5GB - Graphic card: Compatible OpenGL (The code includes a DVD for installation and a USB key) Xilog Maestro Features Programming - Parametric, graphic programming - Assisted programming with graphic and syntax help for drilling operations - Possibility to create and save machining macros Integrated additional functions - Self-diagnosis and possible error messages or malfunctions, in the operator's language - User interface in Dsdpfx Acjvvi I Rs Nscc

Condition: used, Year of construction: 2018, Startech cn MAIN FEATURES FLEXIBLE AND CUSTOMIZED PRODUCTION COMBINED WITH SPEED AND PRECISION DRILLING FROM ABOVE WITH REFERENCE TO THE TOP OF THE PLATE ALLOWS ABSOLUTELY PRECISION MACHINING NUMERICAL CONTROL WITH 7" COLOR SCREEN: SIMPLE AND INTUITIVE TECHNICAL DATA Startech CN AXES Max. workpiece dimensions X-Y-Z mm 3050 x 800 x 50 Min. workpiece dimensions X-Y-Z mm 300 x 90 x 10 Drilling/slotting work area mm 0 x 800/0 x 800 X-axis stroke mm 750 Max. travel speed of the X-Y axes m / min 25 DRILLING UNIT Vertical spindles number 7 (4X-4Y one of them common) Horizontal spindles (along the Y axis) Number 2 (1+1) Horizontal spindles (along the X axis) Number 1 Fixed groove saw (direction) X Diameter of the groove saw mm 100 Max. thickness of the groove saw mm 5 Motor power kW (HP) 1.5 (2) Spindle speed rpm 3350 Speed of the groove saw rpm 4300 INSTALLATION Power supply V (Hz) 380 / 400 (50 / 60) Installed power KVA 4.5 Compressed air demand bar 6 Compressed air consumption Nl/cycle 90 Extraction demand m3 / h 1200 Extraction air speed m / sec 20 Extraction nozzle diameter mm 120 GENERAL CHARACTERISTICS Universal CNC drilling machine with work table with fixed gantry and movable workpiece for performing the following machining operations: - Vertical drilling on the panel surface - Horizontal drilling on all four sides of the workpiece - Groove Milling with integrated groove saw in the "X" direction. Self-supporting structure. Machine frame made of tubular steel to provide a large base for the work table. The structure is positioned on three self-leveling feet. The electrical control cabinet is integrated into the machine frame. "Easy Motion" central Bakelite support table: - an MDF sector for through-hole drilling, automatically pivoting for horizontal drilling - an infeed roller that facilitates panel loading - a rear roller conveyor that facilitates panel sliding - left and right stops - a central aligner with manual adjustment. The left and right stops are required to drill the two opposite sides of the panel horizontally in the "X" direction. Panel positioning along the X axis is achieved by means of suction cups. Unit support. This is a gantry structure made of tubular steel. The main machining unit is installed on the gantry. F10L drilling unit includes: - 7 independent vertical spindles - Drill chuck D10 mm - Distance between spindles 32 mm - 2 horizontal drilling heads, 1 in X direction with a single drill, 1 double drilling head in Y direction (1 + 1 drill chuck D10 mm) - Speed 3350 rpm - 1 integrated sawing unit in X (max. diameter 100 mm) - Saw blade speed 4300 rpm - Motor power 1.5 kW - Vertical pneumatic travel per spindle 70 mm - Horizontal pneumatic travel of the drilling unit Positioning of the workpiece and drive of the machining unit A CNC-controlled suction cup clamps the workpiece and positions it sequentially under the machining unit during machining. The movement in X and Y axis is carried out on THK guides with transmission on reinforced toothed Movement in Z axis is carried out pneumatically on "ball-bushing" guides with positioning on stop adjustable via the positioning of the working units is carried out via technology and drives with -CONTROL The control was specially developed for use Dcedpfx Aovwbp Aec Noc

Condition: used, Year of construction: 2012, Basic machine Olimpic K 800 "T-ERL" (47) 1 pc. BASIC EQUIPMENT: - Ribbed steel machine frame with tubular reinforcements for optimal work unit support - Pivoting control panel - Support roller conveyor with ball bushing guides along the entire machine length - Protective and sound-absorbing hood with separate doors between the gluing and finishing units - Extractor nozzles located on the sound-absorbing hood - Electrical system with lockable main switch - Emergency/stop buttons at the inlet and outlet - Inverter for electric spindles. PLATE FEED SYSTEM - Feed chain with rubber glide shoes, mounted on a 1 1/4-inch industrial chain with a high friction coefficient - The chain slides on two guides made of hardened and ground steel, one round and one flat, to guarantee straight feed and protect against lateral misalignment. --- Automatic central lubrication of the feed chain - The upper pressure beam is made of thick-walled steel construction. Complete with double rows of bearing rollers and protective device for the printing rollers - manual lifting of the printing unit with automatic working unit positioning when changing the plate thickness - mech. Digital display for checking the selected panel thickness. ORION 100 CONTROL SYSTEM. Control device complete with PLC, allows fast, easy, and error-free execution of custom processing programs (max. 60 programs). Manages the pneumatic positioning of the units, if present on the machine. (The control system does not include pneumatic positioning). - Alphanumeric keyboard and display - Function keys for quick control of the processing units - Ambient temperature range from 0 to +45° C. MAIN FUNCTIONS - Control of the processing units and automatic activation of the motors - Control and regulation of the glue pot temperature - Selection of longitudinal and transverse processing without program change - Simple and guided diagnostics for easy troubleshooting - Statistics on absolute data and individual processing: number of pieces, edge consumption, total chain feed distance - Unit of measurement selectable in mm or inches. Technical data OLIMPIC K800 T-ER L Edge thickness: 0.4 to 8 mm Max. gluing thickness of the roll edge: 3 mmFeed speed: 12/18 m/minWorking height: 8 to 60 mmMax. dimensions of the edge cut: 135 mm²Turntable diameter: 780 mmMax. oversize compared to the panel thickness: 4 (2+2) mmMin. panel width (with 210 mm min. length): 55 mmMin. panel length (with 100 mm min. width) - with strip or roll edges max. 3 mm: 140 mm - with solid wood edges: 200 mmMin. distance between consecutive panels at 11 (16) m/min: 750 (850) Standard equipment - Pre-milling unit in the infeed RT-E- Gluing station VC-800- Trimming unit KSEL- Flush trimming unit, tiltable RI/800- Rounding unit ROUND K- Scraper unit RAS-V- ½ free space for surface scraper- 1 S free space for surface scraper or Universal milling or buffing unit - 1 free space for air nozzle unit. European safety regulations (C.E. mark). 1 unit. Voltage 400 EU. 1 unit. Frequency 50 Hz. 1 unit. "Autoset" for ER2, T-ERS, and T-ERL models. 1 unit. Allows all necessary adjustments to be made from the control panel for each machining change. Includes: - time-controlled pressure unit - pneumatic and independent pivoting of the mitre saw blades (front/rear) - pneumatic remote adjustment for the RI/800 flush trimming unit. Djdox Twdtepfx Ac Nscc

Condition: used, Year of construction: 2023, Exhibition machine Garbsen HORIZONTAL PANEL SAW GABBIANI P Manufacturer: SCM Type: GABBIANI P80 Year of manufacture: 2023 1 unit MAIN FEATURES INDIVIDUALLY SELECTABLE AIR CUSHION TABLES: AN INDISPENSABLE TOOL SIDE SAFETY DEVICES: MORE SPACE FOR WORKING FLOATING GRIPPERS: GUARANTEED PERFECT CUT TECHNICAL DATA GENERAL INFORMATION gabbiani p80 Saw blade projection mm 80 Working table height mm 950 Standard number of grippers 5 Number of grippers for versions 33/38/43 9 / 10 / 10 Number of grippers for versions 33/38/43 with FlexCut 1 unit (single gripper with double fingers included) 10 / 11 / 11 CUTTING DIMENSIONS Version 33 mm 3300x2100 Version 33 (Opt.) mm 3300x3200 Version 38 mm 3800x3200 Version 38 (Opt.) mm 3800x3800 Version 43 mm 4300x3200 Version 43 (Opt.) mm 4300x4300 AXIS SPEED Variable saw carriage speed m/min 6 – 60 Variable pusher speed () m/min 60 MAIN SAW BLADE Motor power (S6 -40%) - 50hz (star-delta start) kW (HP) 7 (9) (11) Speed – 50 hz rpm 4650 Saw blade diameter mm 340 Shaft diameter main saw blade mm 80 SCORING BLADE Motor power (S6 -40%) - 50hz kW (HP) 1.5 (2) Speed – 50 hz rpm 5850 Scoring blade diameter mm 200 Shaft diameter scoring blade mm 80 INSTALLATION Installed power kW 12÷15 Base machine voltage Euro voltage (400 V / 50 hz) Compressed air demand NL/min 300 Required compressed air pressure bar 7 Extraction air requirement m3/h 2440 Extraction air speed m/sec 20 Extraction port diameter mm 4x120 () Note: in countries where EU standards apply, the forward pusher feed speed is limited to 25 m/min. GENERAL CHARACTERISTICS Fully automatic, PC/PLC-controlled horizontal panel saw suitable for cutting solid wood, MDF, chipboard, plywood, and similar materials. Frame and working table – Machine frame is a steel tube construction – Working table of rib-reinforced steel with Bakelite coating – Longitudinal fence on the left side Saw carriage made of steel, consisting of: – a motor for the main saw blade and a motor for the scoring blade – vertical lifting of the saw blade on linear ball bearing guides and shoes – running rollers of hardened and ground steel – balanced mass distribution for optimal cut quality – running direction towards the longitudinal fence – saw carriage drive via rack and pinion – carriage travel on cylinder guides – cylinder guides of hardened and ground steel (5-year warranty), protected by special dust wipers – pneumatic switch for fast and safe main and scoring blade change Pressure beam – pressure beam with uniform pressure across the entire cut length, recesses to prevent collision with grippers; pneumatic height adjustment via high-precision rack and pinion, pressure adjustable from 1.5 to 6 bar – dual extraction system with one unit above the pressure beam for cleaning the work table and one unit below on the saw carriage – side automatic aligner with pneumatic cylinder over the entire length. Sliding on linear ball bearing guides and shoes. * Travel distance: 1200 mm * minimum working width: 60 mm * maximum working width: 1200 mm Positioning pusher and rear part of the machine – Positioning pusher full length, powered by a robust drive shaft. Positioning pusher control... Dcedpfx Aox Twcvec Nec

Condition: good (used), Year of construction: 2016, operating hours: 16,977 h, functionality: fully functional, feed length X-axis: 140 mm, feed length Y-axis: 50 mm, feed rate X-axis: 18 m/min, edge thickness (max.): 3 mm, total length: 6,000 mm, workpiece height (max.): 60 mm, overall weight: 3,000 kg, SCM OLIMPIC K 800 - T-ERL EDGEBANDER EDGEBANDER (W/PRE-MILL & CORNER ROUNDING): Specifications: -- Edge Capacity, 0.4 to 8 mm (0.016 to 5/16") for strip feeding. -- Panel Capacity, min. width 50 mm and 140 mm min. length, (2-3/8" and 5-1/2"). Panel thickness min./max. 8 - 60 mm (3/8" - 2-3/8"). Equipped With: -- Adjustable In-feed Fence: Manually pre-set with digital indicator and pneumatic panel spacing device. -- Pre-Milling Station, RT-E: Spindles 2 x 3.0 HP, 12,000 RPM, (1) with PLC controlled jump action and manual digital indicators positioning. -- Automatic Strip & Coil Feed Magazine: For straight edges and 3 mm guillotine for coils. -- Gluing Station: For EVA (Hot Melt) with Teflon coated glue tank and quick disconnect to change glue tanks fast if needed. Heat-up time approx. 10 Min. -- Pressure Section: Servo motor positioning, (4) pressure rollers, first larger, Teflon coated and powered. Workstations: -- End Trimming Station K-SEL: Front & rear 2 x 0.5 HP, 12,000 RPM motors mounted on THK guides, swivels 0 - 15, rapid set up between straight and angled cutting with the automatic swivel cylinder. -- Flush Trimming Unit: Top/Bottom, 2 x 1.0 HP, 12,000 RPM with 2 pre-set pneumatic positions, flush and overhang, remote pneumatic in/out positioning. -- Bevel/Radius Trimming Unit: Programmable, servo motor positioning, 2 x 1.0 HP - 12.000 RPM motors for change-over on the fly. -- Corner Rounding / Trimming Unit: For additional top & bottom trimming of linear an/or vertical leading & trailing corner when edgebanding all (4) sides, 2 x 0.8 HP - 12,000 RPM motor. -- Profile Scraping Unit "RAS/1000": Top/Bottom with (2) indexed manual pre-sets. Large dia. copy wheels for max. accuracy and pneumatic in/out positioning. -- Glue Scraping Unit, "RC-V": Top/bottom flat glue scraper with pneumatic positioning through controller and air-blow off nozzle to keep the knifes clean. -- Buffing Unit "SPN": Top/bottom, oscillating 2 x 0.25 HP - 3,000 RPM motors, tilting up to 12. -- Hot Air Unit: Single blower with adjustable heat range and directional heat shield for top/bottom coverage. Restores color luster on thick pvc edging materials that my be lost during the edge scraping process.Operator Interface: -- Startouch Controller, 12" color touch screen, swivels 270 at in-feed of machine. Capable to store (100) programs, (6) at the touch of a single key. Graphical display of all working units. Tracks production data, diagnostic information and monitors maintenance schedules. Complete With & Features: -- Feed-speed, 36/52 FPM, 1 x 2.5 HP feed drive motor, 200 Hz frequency inverter for all trimming units. -- Electronic, programmable hold-down pressure beam positioning, lighted safety/sound enclosure cover and outboard panel support. -- Actual Model: OLIMPIC K 800 T-FR2 2 glue tanks + 1 glue tank for spare parts Dcodpjxxy Rkofx Ac Noc

Condition: excellent (used), SINGLE SIDE EDGE BANDER (Left) Edges (band in rolls) thickness (Min/Max) mm 0,4 / 3 Edges thickness in strips / lippings (min/max) mm 0,4 / 8 (12)* Panels thickness (min/max) mm 8 / 60 Numerical Control "StarTouch" + "Touch 7" Feeding speed m/min 12-18 Top pressure system with rubber belt (C.N.) Spraying unit (Anti-sticking liquid) AAR In-feed fence, adjustable by N.C. "EASY SIZE PLUS" Pre-milling Unit (vertical joint trimmers) 2 x Kw Lamps to heat the workpieces side Glueing Unit (P.U.R. Glue + Quick Melt system) "VC/800" - "VC/6" + "AirFusion AF15" Band Pressure zone (N.C. adjustment) Edge coils supporting unit - 1 Snipping (end-cutting) K/SEL Rough Trimming unit RS/K Fine Trimming unit RI / 800 (3 pos.) Dcedpoxlqntefx Ac Nec Multi Function Unit (Profile contour Trimming Unit) “4 EDGE” KIT Spraying Unit (for sliding liquid) Profile edge scraping unit RAS/1000 Glue scraper RCA / 2C Milling grooving unit K-100 (1 x Kw 1,8) 90° Hot Air Heater (to reactivate the color of plastic tape) Panels Return System "SAG" Mod. SPINNER 47 / 63

Condition: excellent (used), 4-SIDED SIZING-SHAPING LINE (currently for Internal Doors). Composed by of the following machines: X10023A) Motorized infeed rollers table "CELASCHI"" X10023B) Double End Tenoner "CELASCHI" Mod. TSA 3 B 480 A Installed power KW 65 X10023C) 90° Motorized Transfer ("L-shape") conveyor "CELASCHI" Mod. Dodpfx Acswzmbqs Nscc X10023D) Double End Tenoner "CELASCHI"" Mod. TSA 2 B 360 Installed power KW 60

Condition: excellent (used), Year of construction: 2013, functionality: fully functional, Morbidelli M800 X5 machining center X working field: 6360 Y working field: 1680 Z working field: 350 5-axis electrospindle with liquid cooling, 13 kW – HSK 63F Tool magazine disc moving on X-axis, 48 tool positions Processing unit with Vector 360° axis 1 cutting saw blade 1 vertical outlet for milling 3 vertical outlets for drilling 3 vertical outlets for handle holes 2 horizontal outlets for milling 2 horizontal outlets for drilling Dcsdox I A Aqopfx Ac Nsc CE safety system with bumpers CNC PC-Office control with integrated computer 3D programming system WOP XILOG-MAESTRO 250 m³/h vacuum pump Available December 2026.

Condition: used, Year of construction: 2015, total length: 2,300 mm, total width: 1,950 mm, total height: 1,850 mm, Empty weight: 1.240 kg Price: On request Dsdpfx Aoxhchdsc Nocc - Year: 2015 - Documentation available: No - CE marking present: Yes - CE certificate present: No - Serial number: AB/222595 - Voltage [V]: 400 - Current consumption [A]: 10 - Transport dimensions: 2300mm x 1950mm x 1850mm (l x w x h) - Transport weight [kg]: 1240kg - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: like new (used), Year of construction: 2012, functionality: fully functional, I sell the horizontal foil wrapping packing machine Dedpfor Alx Uox Ac Njcc Producer: SCM GROUP, Italy Model: PACK 8080 Year: 2012 / like NEW, almost not used before Working circle diameter 1300mm. Working tables width 900mm. Feeding manual with tables total length 2,60m Assembled, ready for work. Avialable immediately. On stock.

Condition: used, Year of construction: 1999, Carriage length: 3800 mm Cutting width at the width stop: 1500 mm Cutting width at the cross-cut fence: 3200 mm Dcodpjvxi Ddsfx Ac Njc Cutting depth: 140 mm Scoring unit: no Saw blade height adjustment: electric Swivel adjustment saw blade: electric Width stop adjustment: electric / position control Saw blade angle display: digital Cutting height display: - Width stop display: Digital Cutting ruler display: Scale Saw blade diameter: 400mm Speeds: 3 Motor power: 7,5kW Motor brake: Yes, automatic Suction connection: 80mm and 120mm Machine length: 3900mm Machine width: 2200mm weight: 1000kg

Condition: excellent (used), two bottom heads Dedpsw Ad Tgsfx Ac Njcc one side - right head heads with 21 spindles spindles span 32mm motors 3x1,1kW 2 pneumatic pressure regulation of span between heads right/left spindles

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, No reserve price - guaranteed sale at the highest bid! Line consists of: SCM Windor 100 SCM Superset NT Dedpfsvy Ahxox Ac Nscc SCM Profitech SCM Fleximat SCM Windor 100

Condition: new, Year of construction: 2023, machine/vehicle number: MR005937, Universal drilling and grooving CNC machine. Easy to use, compact, and fast in processing. The machine is equipped with the following options: - Panel end sensor - Z-axis pressure increase (recommended for hard materials) - Maestro CNC software - Keyboard type: Qwerty - Fan for electrical cabinet cooling - Automatic lubrication system Technical specifications: - Minimum panel thickness: 10 mm - Maximum panel thickness: 50 mm - Minimum panel length: 300 mm - Maximum panel length: 3000 mm - Minimum panel width: 90 mm - Maximum panel width: 900 mm - Positioning speed: 20 m/min - Number of vertical drilling spindles: 7 pcs Dcedpfx Aewy U A Hsc Njc - Number of horizontal drilling spindles (Y-axis): 2 pcs - Number of horizontal drilling spindles (X-axis): 2 pcs - Integrated grooving saw blade: Yes - Diameter of grooving saw blade: 125 mm - Motor power: 3 HP - Serial number: KK00039354

Condition: ready for operation (used), Year of construction: 2017, functionality: fully functional, travel distance X-axis: 3,680 mm, travel distance Y-axis: 1,380 mm, travel distance Z-axis: 250 mm, controller model: Xilog Maestro, spindle speed (max.): 24,000 rpm, TECHNICAL DETAILS Working Area X-Axis: 3,680 mm Working Area Y-Axis: 1,380 mm Working Area Z-Axis: 250 mm Spindle Speed: 24,000 rpm Number of Working Zones: 2 Number of Adjustable Bars: 6, 1,300 mm Number of Pneumatic Bakelite Bars: 4 Number of Adjustable Suction Cups: 3 Front Tool Changer System: 10 positions Rear Tool Changer System: 16 positions F 12L Vertical Drilling Head Spindles: 8 F 12L Horizontal Drilling Head Spindles X-Axis: 2 F 12L Horizontal Drilling Head Spindles Y-Axis: 2 MACHINE DETAILS Electrospindle: 12 kW, HSK 63F Dcedpfoydmbnox Ac Njc Vacuum Pump: 250 m³ Control System: Xilog Maestro EQUIPMENT Tecpad Mobile Console Bar Worktable Laser Line for Virtual Zero Positioning on Y-Axis Prisma KS 5-Axis Vertical Electrospindle Tool Group Blades for Groove Cutting Pro-Speed Safety System Front Guard and Safety System Automatic Lubrication System

Condition: ready for operation (used), Year of construction: 2022, functionality: fully functional, machine/vehicle number: AB00022255, working height: 250 mm, table length: 520 mm, table width: 900 mm, feed roller diameter: 67 mm, blade shaft diameter: 120 mm, TECHNICAL DETAILS Djdpfx Ajydc Ecec Necc Table dimensions: 520 x 900 mm Working height: max. 250 mm Working height: min. 3 mm Tersa cutterhead: 520 mm with 4 knives Cutterhead diameter: 120 mm Feed roller diameter: 67 mm Feed speed: 5 / 8 / 12 / 18 m/min MACHINE DETAILS Main motor power: 9 kW Weight: 1,058 kg EQUIPMENT Pneumatic table adjustment Electronic thickness table height adjustment via positioning control Tilting fence including auxiliary fence for strips

Condition: ready for operation (used), Year of construction: 2019, operating hours: 336 h, functionality: fully functional, total length: 4,764 mm, edge thickness (max.): 8 mm, overall weight: 1,840 kg, controller model: Maestro Pro Edge, Edge banding machine with only 336 operating hours & comprehensive accessories! TECHNICAL DETAILS Max. edge thickness: 8 mm MACHINE DETAILS Control: Maestro Pro Edge Electrical Data Voltage: 400 Volt Frequency: 50 Hz Dimensions & Weight Machine length: 4,764 mm Dcodpfjydc Abox Ac Njc Weight approx.: 1,840 kg Operating hours: 336 h Edge Banding Machine Configuration: Flush trimming and scraper unit, radius: 1 mm Flush trimming and scraper unit, radius: 2 mm Spraying unit for edge finishing Spraying unit for delicate edges Surface scraper "RC-V" Brushing unit "SP-V" "SAVENERGY" kit "EASY SIZE" device Internal lighting for the enclosure and gluing area Ceramic lamp with infrared rays Electronic positioning of the pressure rollers Spare adhesive tank "SGP" with NC dosing system Additional adhesive tank "SGP" with NC dosing system Manual feed "Nesting" tracing rollers Diamond tools H=64 for pre-milling unit, 2 teeth Base

Condition: used, Number of spindles 6 St. Working width 240 mm Working height 120 mm Dimensions (L/W/H) 4900 x 1700 x 1700 mm weight of the machine ca. 3500 kg Control CNC SCM SUPERSET NTE 31 PLUS automatic profile milling machine with 6 shafts 14 axis control with touch screen - WINDOW VERSION Machine with 6 spindles Spindle speed 8,300 rpm Working width 240 mm, working height 120 mm Electronic horizontal and vertical positioning of the spindles Glazing bead cutting Touchscreen controls Detailed technical description, see adjacent PDF documents. Suction nozzle diameter: 1. Spindle down: 120mm 2nd spindle right: 120 mm 3. Left spindle: 120 mm 4. Spindle top: 150mm 5. Spindle top: 150mm 6. Spindle below: 120mm Option: workpiece return to the operator Images are from our archive of a machine of the same model. (Technical information according to the manufacturer - without guarantee!) Dedpfxjyhxmuo Ac Njcc

Condition: good (used), Code: 0293 Brand: SCM Model: T 160 Automatic spindle moulder with tilting spindle with feeder Technical data: Sturdy structure with cast iron table Automatic and manual spindle inclination 0 to 45° Automatic and manual vertical spindle adjustment Dcsdpfx Ajyhqiqec Njc Spindle reverse rotation Table dimensions 1000 x 1000 Worktable height 850 mm Spindle diameter mm 35 Rotation speed 2900-4400-6000-7800-10000 rpm Motor power Hp 5,5 Automatic 3-roller feeder Suction inlet diameter 120 mm Overall dimensions: mm 1100 x 1150 x 1550 h Weight kg 900

Condition: good (used), Code: 0292 Brand: SCM MINIMAX Model: FORMULA F1 - CE Standard Surface planer for planing wood materials, plastics, composite materials and various - CE Standard Technical data: Working width mm 410 Dcjdpfx Acjyhp S Rj Nsc Table length mm 2610 N° 4 knives Shaft diameter mm 120 Shaft rotation speed rpm 5000 Guide tilting from 90° to 45° Max stock removal mm 8 Motor power Hp 5,5 Table height from ground mm 845 Suction hood diameter mm 120 Overall dimensions mm 2610 x 900 x 1070 h Weight kg 575

Condition: used, Year of construction: 2005, Dimensions (LxBxH): 373 x 125 x 190 cm Wide belt sander Timesavers 900 WWS year of manufacture 2006 Serial number 2217/043 units, pre-deburring, deburring, finishingbelt width 900 mmthroughput max. 150 mm50 Hz, 400 V, 58 kW Dsdownhdajpfx Ac Nocc Dimensions: 3500 x 1900 x H2100 mm, weight 4000kg - Year: 2005 - Documentation available: No - CE certificate present: No - Deals (actions): Super deal - Transport dimensions: 3730mm x 1250mm x 1900mm (l x w x h) - Transport packages [pcs.]: 1 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2002, Empty weight: 1.800 kg Dimensions (LxBxH): 325 x 155 x 150 cm Four-sided moulder SCM Compact 23K Built in 2002 Min/max working height 120mm Min/max working width 230mm Working speed 6/12 m/min Spindle speed 6000 Rpm Spindle diameter 40mm Min/max tool diameter vertical spindle 100/180mm Input table length 2500mm CNC Program Engines 1st Spindle - Under 5.5kW Dodownhk Topfx Ac Njcc 2nd/3rd Spindle - Left/Right 11kW 4th Spindle - Up 7,5kW Dimensions 3250x1550x1500mm (LxWxH), Weight 1800kg - Year: 2002 - Documentation available: Yes - CE certificate present: No - Transport dimensions: 3250mm x 1550mm x 1500mm (l x w x h) - Transport weight [kg]: 1800kg Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: used, Year of construction: 2001, Storage location: Supplier Dodpfx Asyhnvzsc Nscc