Used Pusher for sale (419)

Condition: new, Year of construction: 2022, bar-feeder complete servo control. bar lenght 1500mm max bar diameter 104 mm max store 600 mm include support between barfeeder and machine this when spindle is to short. barfeeder is complete servo control. for turning spindel height between 860 and 1200 mm no chamfering neded. for round and hex material power 380 ~ 415 volt 10 A 50 Hz total install, 1 Kw no losing time for adjustments like: setup change, like pusher/pushrod. bar stock center adjustment etc. max bar change time 15 sec. need no air pressure ot hydraulic pressure Eco friendly double axis servo control. automatic diameter adjustment. Fas, reliable and flexible. wide bar range and lenght Knjdpfelczwfjx Affof touch screen HMI enter bar diameter and profile by HMI weight 800 kg

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, machine/vehicle number: 220.242, cutting length (max.): 4,300 mm, saw blade diameter: 350 mm, cutting height (max.): 90 mm, cutting depth: 3,300 mm, TECHNICAL DETAILS Cutting Data Nominal cutting length: 4,300 mm Cutting depth (material pusher positioning): 3,300 mm Cutting height: 90 mm Maximum saw blade diameter (S): 350 mm Scoring saw blade diameter (V): 300 mm Maximum saw blade projection above table (U): 95 mm Stack Height and Panel Thickness Maximum stack height (P): 80 mm Minimum panel thickness (P): 3 mm Strip Aligner Ksdextfhwspfx Affenf Minimum aligning force: 300 N Maximum aligning force: 990 N Other Specifications Maximum clamp opening (K): 90 mm Working height: 970 mm Machine height: 2,020 mm Machine Accuracy Positioning accuracy: ± 0.1 mm (measured at infeed) Cutting straightness: ± 0.1 mm over 3 m cutting length Electrical Performance and Speeds Main saw motor power: 15 kW Forward saw unit speed: 5 – 120 m/min Return saw unit speed: 120 m/min Forward feed speed: up to 80 m/min (Europe 25 m/min EN 1870-13) Reverse feed speed: up to 80 m/min EQUIPMENT Strip aligner Label printer Optimization software HPO/F N5

Condition: good (used), Year of construction: 2018, functionality: fully functional, type of input current: three-phase, total width: 2,400 mm, The Lamina Gluer is a manually fed, in-line folding, gluing, and taping machine. Thanks to its smart design, it can handle different sizes and materials. Tool-free setup enables quick changeovers, even for short production runs. Optional machine features include cold glue, rear support unit, working station, tape applicator, and more. The Lamina Gluer is a straight-in-line gluing machine built on a robust frame made of extruded, anodized aluminum profiles. The machine offers manual feeding as standard, with an optional automatic feeder for die-cut, creased, and slotted materials. The operator positions the blanks, and the hot melt unit applies adhesive as the material passes through the machine. Glue line length and exact position can be pre-set using a programmable logic controller (PLC) and a touchscreen interface. A system of pressure rollers ensures perfect adhesion and guides glued blanks onto a pull-out tray, which is easily adjustable for various sizes. The machine comes equipped with adjustable and interchangeable side guides, enabling efficient gluing of 2-piece boxes. The Lamina Gluer is supplied ready for connection to electric and pneumatic systems. The Lamina Working Station is an additional option for the Lamina Gluer. Products are fed through the Gluer, which applies pre-programmed glue lines, and continue into the Working Station, where they are positioned on vacuum belts. A second piece is mounted and positioned using side lays and pneumatic stops for high-quality finishing. The unit can be adjusted for a wide range of products, from single- to multi-part displays and boxes, large back supports, shelves, and more. Transport Kjdexwcwwepfx Affonf The material is conveyed by four vacuum belts that bring the sheets to a stop bar for subsequent operations. The vacuum is generated by a fan that secures the sheets for optimal handling and precise registration. During production, the operator has full access above the sheets for additional mounting, thanks to the vacuum belt design. Pressure Rollers Material passes through two pressure rollers at the machine’s end for optimal adhesion. Registration Registration accuracy is +/- 1 mm and is achieved by a combination of photocell sensors and pusher guides. The operator uses a side lay guide to simplify the mounting process at the station.

Condition: used, overall weight: 24,000 kg, rotor diameter: 640 mm, number of blades: 114, rotor length: 2,500 mm, power: 247 kW (335.83 HP), No. 10023 Single-shaft shredder Vecoplan VAZ 2500 Used, year of construction approx. 2006 2022 general overhaul Since overhaul approx. 700 operating hours Areas of application: Residual wood, waste wood, packaging material, film, plastic, paper, textiles, domestic waste, commercial waste, production residues as bulk material, production residues in bales 247 kW Rotor length 2500 mm Rotor diameter 640 mm 114 pieces 60x60 cube knives, 4-row Shredding optionally to a grain size of approx. 10 - 250 mm Screen basket 50 mm Throughput capacity up to 25 tons per hour / throughput waste wood approx. 30 tons per hour Material feed with hydraulic pusher Scope of delivery: machine, hopper, control cabinet, refrigerator Mechanization optionally available Transport dimensions approx. 4750 x 4640 x 2340 mm LWH Weight approx. 24000 kg Sale on behalf of customer, ex location near 85456 Wartenberg, without dismantling, without transport and assembly Errors in description and price excepted Dismantling, transport and loading by us optionally possible To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical details, condition description, year of construction and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale Any warranty is excluded for used machines, the following applies: “purchased as viewed” Pictures and videos serve as examples and do not represent the actual scope of delivery Ksdpfjwh T N Usx Affenf Terms of payment: Prices excl. VAT, payment before collection or dispatch Terms of delivery: ex location

Condition: excellent (used), Year of construction: 2009, functionality: fully functional, feed length X-axis: 4,300 mm, feed length Y-axis: 4,300 mm, cutting length (max.): 4,300 mm, cutting height with scoring (max.): 4,300 mm, saw blade diameter: 380 mm, HPP 380/43/43, fully automatec loading with TBP 200/31/22/ Main motor 18.5 kW Machine works perffectly, possible test run Holzma Profi HPP 380 Cutting length: 4,300 mm Cutting width (program-controlled pusher travel): 4,250 mm Knedoxvz T Ispfx Affsf Air cushion table: 2,160 x 650 mm, 3 pcs. + 1* 2,810 mm length Central blower: 1 unit with increased blower performance 2 additional alignment devices Technical Data: Saw blade projection: 95 mm Saw carriage feed: forwards 1–130 m/min, backwards constant 130 m/min Main saw motor: 18 kW Scoring saw motor: 2.2 kW, VVSH aggregate, program-controlled, vertically rising Operating voltage: 400 V (+10%/-5%) / 50 Hz Electrical connection rating for main saw motor 18 kW: 24 kW Power Control CADmatic 4.0 control with 17-inch flat display Labeling with part graphics / label program / label printer PICA 104

Condition: excellent (used), Year of construction: 2009, operating hours: 16,800 h, functionality: fully functional, cutting force: 600 t, power: 242.71 kW (329.99 HP), Lefort Mobile 600 Tons Knodpsuptrpofx Affsf Shear force: 600 t Hold-down force: 120 t Pusher force: 180 t Lid closing force: 240 t Box height: 600 mm Box width: 800 mm Box depth: 6000 mm Available immediately

Condition: good (used), Year of construction: 2014, functionality: fully functional, System consisting of: PANEL SAW SELCO WNT 610 / 4500 x 2200 mm PC-BASED CONTROL SYSTEM Max. cutting length: 4,500 mm Max. saw blade projection (main saw): 95 mm Max. opening of clamping grippers: 90 mm Min. panel dimensions from rear: 1,830 x 915 mm Max. panel dimensions from rear: 3,100 x 2,200 mm Min. panel thickness for rear feeding: 3 mm Worktable height: 985 mm Main saw motor: 15 kW Main saw blade diameter: 380 mm Scoring saw motor: 2.2 kW Scoring saw blade diameter: 200 mm DIGISET: electronic adjustment of scoring saw to main saw QUICK CHANGE: fast blade change at the push of a button Saw carriage drive: 1 - 140 m/min Integrated side aligner in saw carriage: 0 - 4,200 mm Automatic measuring system for manual cuts Pusher extension from 5,500 to 7,800 mm 10 pneumatic clamping grippers on pusher with double fingers 3 front aligners 16 support roller tracks behind the machine table 4 air-cushion tables in front of the machine table, rounded, Knjdpfxoxranps Affsf including movement device for table 2 Automatic ejection of end pieces beyond the cutting line Material support area under the pusher equipped with brush rollers for sensitive surfaces Machine table with air nozzles for sensitive surfaces Automatic device for monitoring the main saw blade consisting of a sensor that detects blade deflection and a system for measuring main spindle speed Software package: QUICKOPTI for optimizing cutting plans directly on the machine OSI PLUS INTERFACE VERSION OPTIPLANNING OPTIMIZATION SOFTWARE incl. hardware dongle, allows management of up to 10 users via network OS LABELLING: graphical editor on the machine control system with workpiece drawings, real-time label printing directly at the machine possible COMMUNICATION BETWEEN STORAGE FEED SYSTEM AND SELCO Industrial label printer at the machine STORAGE FEED SYSTEM RBO WINSTORE 2D STANDARD TRAVERSE 8000 MM Swiveling suction frame 0 - 180 degrees with controlled axis Panel alignment/squareness correction system consisting of 3 photocells mounted on pneumatic cylinders Panel weight detection via load cell mounted on the suction frame in the separation area, checks whether the specified weight value is within the expected range for this panel type. If not, the panel is set down again and the separation cycle restarts. Roller conveyor for stacking and unstacking: 4,200 mm Software: LINE SUPERVISOR with warehouse mapping, catalog, import of machining data from the optimizer, management of BOMs, plant control

Condition: refurbished (used), Year of construction: 1997, functionality: fully functional, machine/vehicle number: 556, Model: Lindner Micromat MS2000 Year of Manufacture: 1997 Condition: Refurbished 2025. Zero operating hours since refurbishment. Location: Riga, Latvia Machine Specifications: Machine Weight: 9.5 t Dimensions: Not specified. Material Suitability: Plastics, mixed waste, etc. Drive System: Motor: Elin AC Motor, 75 kW, 1500 rpm, 400 V, 50 Hz. Frame size: 280S. Mounting: B3. V-belt drive: Ratio i=0.93. Gearbox: Stiebel Type 0220.15. Bore 140 mm. Ratio i=20. Safety Coupling: SecMatic Type 580.32.3.2. Factory setting: 1300 Nm. Rotor Speed: 80 rpm. Hydraulic Unit: Type: MM2000 / 13 / 6 Output: 35±5 l/min Oil Tank: 100 l. Oil: Castrol Vario HDX. Pressure: Inlet 160 bar, Outlet 60 bar. Drive Motor: 5.5 kW, 1425 rpm, 400 / 660 V. Mounting: V1. Pusher Cylinder: 60/35×605 mm. Swivel Cylinder: 50/30×700 mm. Cutting System: Knives: 104 pcs. Size: 43×43×23 mm. Ksdpsxvmqrefx Affjnf Screen Hole Size: Ø50 mm. Material Transport: Screw conveyor. Refurbishment Summary (Completed 2025): Paint: Components cleaned, prepped, and painted. Color: RAL7032 / 2002. Rotor: 22 new teeth installed. 35 existing teeth repositioned. 30 protective tooth covers replaced. Counter-Knives: 3 internal counter-knives replaced. External counter-knives repositioned. Structural Work: Welding repairs performed on frame where cracks were present. Hydraulics: Hydraulic station oil filler cap and motor cover repaired/replaced. Control Panel: Repaired. Assembly: Equipment assembled, installed, and packaged

Condition: good (used), mileage: 195,569 km, power: 250 kW (339.91 HP), first registration: 03/2015, tire size: 315/80R22,5, axle configuration: 6x2, wheelbase: 4,320 mm, brakes: retarder, color: white, driver cabin: day cab, gearing type: automatic, emission class: euro6, suspension: air, Year of construction: 2015, Equipment: ABS, air conditioning, cruise control, traction control, = Additional Options and Accessories = - 2nd diesel tank - Digital tachograph - Electric windows - Electric mirrors - Tachograph (control device) - Fixed configuration - Short cab - Power take-off (PTO) - Pump - Central lubrication - Additional braking system = Notes = Number of axles: 3, Configuration: 6x2, Unladen weight: 16,105 kg, Gross weight: 28,500 kg, Total tank capacity: 1 litre, 2nd diesel tank, Fifth wheel coupling: Fixed, Number of differential locks: 1, Central lubrication, Suspension type: Air suspension, Cab type: Short cab, Cruise control, Tachograph (control device), Digital tachograph, Air conditioning, Electric windows, Electric mirrors, Radio/cassette, Colour: White, Heated mirrors, Lighting type: Halogen lamps, Air conditioning, Flashing lights, Engine power: 250 kW (335 Hp), Fuel: Natural gas, Euro 6, Transmission type: Opticruise, Gearbox make: Scania, Gears: 12, Additional braking system, Retarder make: Scania, Power steering, ABS, ASR, PTO, PTO type: 1, Starter battery, System type: Pusher 4000 OB, Pump, Seat upholstery: Fabric, Seat adjustment: Manual = Further Information = Driveline Fuel type: Natural gas Knodpfx Asxqxabsffof Transmission Gearbox: SCA, 12 gears, automatic Axle configuration Tyre size: 315/80R22.5 Brakes: Disc brakes Suspension: Air suspension Axle 1: Steering; Tyre tread left: 3 mm; Tyre tread right: 3 mm Axle 2: Twin tyres; Tyre tread left inside: 9 mm; Tyre tread left outside: 11 mm; Tyre tread right inside: 7 mm; Tyre tread right outside: 7 mm Axle 3: Lift axle; Steering; Tyre tread left: 2 mm; Tyre tread right: 5 mm Dimensions Dimensions (L x W x H): 1,050 x 255 x 355 cm Weights Unladen weight: 16,105 kg Payload: 12,395 kg Gross vehicle weight (GVW): 28,500 kg Functional Pump: Yes Maintenance APK (roadworthiness test): valid until 03/2026 Condition Technical condition: good Visual condition: good Damages: none Number of keys: 2 Identification Registration number: KLEYN1 = Company Information = Kleyn Trucks is one of the world’s largest independent dealers of used vehicles. Here, you can choose from a constantly changing inventory of 1,200 used trucks, tractor units, and trailers. Our stock includes all European brands, model years, and price ranges. Why buy from Kleyn Trucks? Simple! • Large, fast-changing stock • Recognizable quality • Competitive pricing • Professional business conduct • We speak many languages • We understand our customers • Support with import and transport • (Export) license plates arranged quickly • Expert technical services • The assurance of recognizable quality • And much more… Visit our website for special offers and our complete stock: Leasing via Kleyn Trucks is possible in most European countries! Quickly calculate your lease rate and send an inquiry through our website. Ask directly about our European warranty package.

Condition: used, No. 3248 Horizontal panel saw HOLZMA Optimat HPP 380/38/38 Used, year of construction 2003 Knjdpsxrglnjfx Affjf Machine still in operation, expected to be available from 19.01.2026 Cutting length 3800 mm Cutting width 3700 mm Saw blade projection 95 mm Main saw motor 13.5 kW Scoring saw motor 2.2 kW Main saw blade 380 x 4.8 x 60 mm Scoring saw blade 180 x 4.8 - 5.8 x 45 mm 7 clamps 3 air cushion tables, of which 1 with angle stop 3 roller elements on front side LKT Operating software Schnitt Profi(t) 9.0 / CADmatic V3.0 15" monitor (replaced in January 2025) V program pusher up to 80 m/min V saw carriage up to 130 m/min Machine dimensions 7205 x 6100 mm LW Sale on behalf of customer, ex location near 90471 Nuremberg, without dismantling, without transport and assembly Dismantling, loading and transport by us optionally possible Subject to errors in the description and price To avoid possible misunderstandings, an on-site inspection is possible and recommended by appointment Sold as is Technical specifications, condition description, year of manufacture and scope of delivery according to manufacturer's brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Images and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices excl. VAT, payment before collection or shipping Terms of delivery: ex location

Condition: used, mileage: 638,000 km, power: 315 kW (428.28 HP), first registration: 07/2016, fuel type: diesel, overall weight: 26,000 kg, axle configuration: 3 axles, next inspection (TÜV): 07/2026, color: white, gearing type: automatic, emission class: euro6, total width: 2,550 mm, total height: 3,700 mm, loading space volume: 84 m³, loading space length: 7,750 mm, loading space width: 2,480 mm, loading space height: 2,200 mm, Year of construction: 2016, Equipment: ABS, air conditioning, electronic stability program (ESP), parking heater, soot filter, * Orten Kettliner Swing Wall Body * Cargo dimensions: 7,750 x 2,480 x 2,200 mm * DEKRA certified according to VDI 2700 ff and DIN EN 12642 Code XL * Beverage certificate * Draft beer certificate * 2 rows of load securing tracks * Lashing rings in outer frame * Fixed rear wall * Liftable steering pusher axle * Retarder * Long cab Knjdpfx Afjxvf Atsfof * 1 bed * Differential lock * Full air suspension * Spoiler * Air conditioning * Heated seats * Adaptive cruise control * Attention, lane keeping, and brake assist * Automatic transmission * Euro 6 together with tandem swing wall trailer * Orten Kettliner * First registration 07/2016 * Cargo dimensions: 7,750 x 2,480 x 2,200 mm * GVW 18,000 kg * Payload 13,800 kg * Lift axle * Mount for truck-mounted forklift ---- Special equipment: Front axle load 8.0 t, audio system: CD radio (Bluetooth), exhaust downwards on the right, right side mirror with maneuvering setting, standard and DuoMatic brake coupling, compressed air coupling in the cab, additional air tank, high pressure air system, air horn, cab floor with 170 mm engine tunnel, tinted windscreen with band filter, vehicle without trailer coupling, 12.7 cm info display with video function, fuel tank: 390 l aluminium, steering pump (fixed), side air intake at cab, roof spoiler (adjustable), reinforced engine brake, rear steering axle, liftable, tire pressure monitoring system, spare wheel, side-mounted spare wheel hoist, retarder, acoustic reversing warning (external warning signal), fleet management system interface, drawers below bed rail, automatic circuit breaker, driver’s cab seats: comfort suspension driver seat, sunblind for side windows, driver and passenger door, steel wheels 9.00x22.5, 12V socket in passenger footwell, additional 24V socket in passenger footwell, automatic daytime running lights, preparation for reversing camera Additional equipment: EURO 6 emission standard, axle configuration: 6x2, Actros 4, trailer brake 2-line, left-side connections, 24V/15-pin trailer socket, electrically adjustable and heated exterior mirrors, rear axle differential lock, steel compressed air tank, driver assistance system: attention assist (drowsiness detection sensor), driver assistance system: brake assist (Active Brake Assist), driver assistance system: lane keeping assist, cab width: 2.30 m, cab type: L ClassicSpace, cab suspension: steel sprung, comfort, suspension: air/air (full air), electric window lifters, 100 A alternator, 12-speed transmission – Type: G 211-12, AdBlue tank: 60 l, manual roof hatch (steel), rear axle: crown wheel 440, body/chassis: chassis, comfort lower bunk, central locking, communication interface, radiator grille shutter, 2-stage air compressor, engine: 10.7 l – 315 kW R6 diesel (OM 470), engine compartment encapsulation, single tire rear steering axle, ramp mirror, residual heat utilization, disc brakes front and rear, seat cover/upholstery: fabric, front passenger functional seat, driver seat backrest foldable, voltage converter 24V/12V 10A, front splash guards, front axle stabilizer, additional stabilizer rear axle/rear steering axle, external storage flap left, cab 24V socket, tachograph/EC control device, cab door extension, aerodynamically designed underbody paneling, front underride guard, CB radio preparation, toll registration preparation, dropped front axle, regulated water pump, permissible gross weight

Condition: ready for operation (used), functionality: fully functional, Year of construction: 2021, arm reach: 3,900 mm, conveyor belt length: 8,000 mm, conveyor belt width: 600 mm, product height (max.): 2,600 mm, No reserve price – guaranteed sale to the highest bidder! The machine's original price in 2021 was EUR 1,480,000 (net)! TECHNICAL DETAILS Performance and Capacity Processing capacity: 60 pallets per day Boxes per pallet: up to 54 units Maximum box weight with 54 boxes: 15 kg Overall height from top of pallet: 2,500 mm Maximum total height (including pallet): 2,600 mm Maximum total load: up to 500 kg Process Times Stacking time per box: 12–15 s Wrapping time: approx. 30 s AGV cycle time (incl. pallet change, wrapping, labeling, transport): about 4 min Transport and Material Flow AGV travel distance: approx. 70 m Number of pallet change positions: 6 Available positions during pallet change: 5 Robot Industrial robot: 6-axis articulated arm robot Payload: 120 kg Reach: 3,900 mm Availability: 99.9 % Protection class (robot): IP64 Robot control: KUKA, protection class IP54 Robot pedestal: height 1,500 mm Safety and Control Technology PLC: Siemens S7-1500 with MP 277 Touch Panel, 19" industrial PC panel Central safety control: with decentralized I/O modulation Profinet slave card: for PLC communication Safety light curtains: 1× A 1,500 mm with muting (3 for robot cell, 1 for door, 1 for wooden pallet stacking) Conveyor Technology and Pallet Handling Powered pallet conveyor: length 4 m, width 1,200 mm Pallet transfer station: GoPal E24/W for docking station Pallet station power unit: GoPal 400 / E24/W Pallet detection kit: included AGV System Transport unit: autonomous AGV GoBot GoPal E24/W Server: GoControl Operating unit: GoPal operating unit (1× call button) Interfaces: GoPal AUX Interface Box (I/O) Integration: fully integrated into AGV system Knedpfx Afoxu Upmsfef Conveying Technology and Singulation Box conveying line: 17 m long, 600 mm wide Horizontal robot transfer section: 1 m Belt conveyor for boxes (new line): 8 m long, 600 mm wide Singulation system: pneumatic pusher Singulation stopper: included Pallet Stacking Systems Automatic pallet stacking system for Euro pallets: capacity 13 pallets, manufacturer e.g. Palomat or similar Automatic pallet stacking system for wooden pallets: capacity 13 pallets, manufacturer e.g. Palomat or similar MACHINE DETAILS System footprint: 5.6 m² (base area) Connected load: 38 kW Weight: 3,500 kg Note: Further information on the equipment configuration can be found in the attached specification sheet.

Year of construction: 2023, condition: used, Used machine Year of manufacture: 2023, delivered in 2024 Condition: as new, machine is in original packaging and has not been commissioned Equipment and technical data: Infeed Table / Cross Conveyor: - Number of strands: 6 × Supergrip timing belts - Pitch: 650 / 650 / 850 / 1500 / 1500 mm - Length: approx. 1.8 m - Drive: geared motor, 1.5 kW - Minimum workpiece infeed length: 0.8 m - Function: Automatic transfer of raw material by lowering level to the infeed table Infeed Table: - Smooth sliding table with sliding plastic for damage-free feeding of raw material by servo pusher into the machining zone - Support width: approx. 200 mm BLOCKHAUS 4F-SERVO (main milling unit): - Machining dimensions: 140 × 200 mm - Maximum horizontal milling depth top: 60 mm - Maximum horizontal milling depth bottom: 35 mm - Maximum vertical milling depth: 95 mm - Milling spindles: Ø 30 mm - Horizontal milling tools: 2 × D = 220 mm × W = 120 mm - Vertical milling tools: 2 × D = 280 mm × W = 120 mm - Motor power: 4 × 4.0 kW - Feed: horizontal and vertical via SERVODRIVE, infinitely variable via software Kjdpfx Aoxavtkjffenf - Milling depth adjustment: spindle with digital counter - Workpiece clamping devices: vertical pneumatic, horizontal pneumatic - Extraction: below-floor hopper Ø 160 mm (pit by customer required) - Control: IPC / PLC / IITO software - Machine frame prepped for end tenon or dovetail milling, drilling unit and crosscut saw - Machine enclosure: fully closed, with swiveling safety hood (gas strut, viewing window) - Electrical control cabinet on base, cable carrier 3.0 m Option i (automatic milling depth adjustment for 4F milling unit): - Four additional NC-controlled servo axes for automatic positioning of the 4F tools - Control via IPC / IITO software - Function: automatic milling depth adjustment with ±0.1 mm tolerance - Extended machining capabilities: - individual grooves and millings on four component sides, - recesses and markings for window and door openings, - double and triple joints, - half corner joints (e.g. for top and bottom log beams) Tools: - 2 × 3-piece groove cutter D 220 mm, width 21–65 mm, LM - 2 × 3-piece groove cutter D 280 mm, width 21–65 mm, LM - 1 × end tenon cutter D 240 mm × 20 mm - 1 × dovetail cutter D 40 mm, width 15 mm Combination End Tenon & Dovetail Milling Unit: - 3-axis milling unit for production of end tenons and dovetail joints - End tenon cutter Ø 240 mm × width 30 mm - Max. milling depth for end tenon: 40 mm - Dovetail width variable - Motor power: 4.0 kW - Speed: inverter-controlled, max. 4,500 rpm - Feed (DT.Y axis): SERVODRIVE, infinitely variable - Height adjustment (DT.Z axis): SERVODRIVE - Rotation adjustment (DT.R axis): SERVODRIVE - Workpiece clamping device: vertical pneumatic - Minimum beam thickness for longitudinal connection: 80 mm - Control: automatic via IPC / PLC / IITO software Horizontal Drilling Unit with Drill Guide (BGD SERVO): - Max. drilling diameter: Ø 30 mm - Drill Ø = 20 mm included in delivery - Motor power: 1.1 kW - Speed: 1,500 rpm - Feed: SERVODRIVE, infinitely variable - Height adjustment (Z axis): SERVODRIVE, digital counter - Workpiece clamping device: vertical pneumatic

Condition: used, machine/vehicle number: 006006, Max. panel width: 2300 mm Max. panel length: 4300 mm Knjdpfxsu Rv Uqe Affof Main saw blade projection: 135 mm No of Rip saw Grippers: 7 No of Cross Cut Grippers: 20 Second flexible pusher: yes Panel Rotation Station: yes

Condition: used, Hydraulic wood panel gluing press NOES Specification: Model: NOES Number of pushers: 6 Motor power: 2 x 17 kW Power: 3 x 380 V Made in: Denmark Kjdpfx Afoqla H Uofsnf If you have any further questions, we will be happy to answer them.

Condition: like new (used), Year of construction: 2022, operating hours: 114 h, power: 160 kW (217.54 HP), rotational speed (max.): 85 rpm, Details: - Enclosed hopper with suction point - Pusher with profiled cutting chamber floor - Safety lines for hydraulics - Machine operation down to -25°C - Wear protection package (checked pattern) Kjdpfxjxup Epj Affenf - Electrical integration for belt conveyor (3 kW–11 kW) - Bus connection to external control system - Power control with frequency converter incl. air conditioning - Energy measurement module - Control cabinet enclosure rated for temperatures down to -25°C

Condition: used, Year of construction: 2024, INDEX MS22-8 Mfd. 2024 2 NCU (4) Y-Axis SL Control Cutting hours: 1,000 Turnkey Available Located in Europe 4-Meter IEMCA SIR MS22-8/43/P Rack loader 50 Hz D9-13-19-25 Bar length 4300 mm with drilling unit and minimum quantity lubrication unit additional end-of-bar sensor Bar stock 500mm (D12-D24) Bar stock 340 mm (D5-D11). Additional storage chain for 22 bars with Profinet interface. 1 11007253 (21711) 1 set (8 pieces) bar stock pushers, external clamping for bar stock diameters D7-D10 mm, internal clamping for bar stock diameters D13-D18 mm, consisting of: 8 bar stock pushers D12 8 rotating sleeves D12 1 10287026 (21712) 1 set (8 pieces) bar stock pushers, external clamping for bar stock diameters D11-D16 mm, internal clamping for bar stock diameters D19-D24 mm, consisting of: 8 bar stock pushers D18 8 rotating sleeves D18 1 10536056 (21713) 1 set (8 pieces) bar stock pushers for bar diameters D17 mm-D22 mm, consisting of: Kodpfxjxnrtcs Affonf 8 bar stock pushers D23 8 rotating sleeves D23 1 10414481 (21702) 1 set (8 pcs.) of internal clamping sleeves D12mm for bar diameters D13 mm - D18 mm Drill diameter D8 mm. 1 10472413 (21704) 1 set (8 pcs.) of external stops D12 mm for bar diameters D13 mm - D18 mm pre-machined. 1 10264327 (21703) 1 set (8 pcs.) of internal clamping sleeves D18mm for bar diameters D19 mm - D24 mm Drill diameter D15mm. 1 10058206 (21705) 1 set (8 pcs.) of external stops D18 mm for bar diameter D19 mm - D24 mm pre-machined. 1 12123486 Drill for drilling unit consisting of: 1 indexable insert drill D 15 mm 10 indexable inserts for steel 2 solid carbide drills D 8 mm

Condition: refurbished (used), Year of construction: 2007, power: 45 kW (61.18 HP), Single-shaft shredder with hydraulic pusher. Brand: VECOPLAN Model: VAZ 1300 M Cutting width: 1,300 mm Power: 45 kW Blades: 40 mm x 40 mm. Machine fully overhauled – hydraulic, electrical, mechanical. Knodpexprbcofx Affsf

Condition: used, Year of construction: 2007, HOLZ-HER – 6310 CUT 110 580 Computer-controlled Panel Saw Watch the video of the machine: Year of manufacture: 2007 Machine number: 136 The machine has been overhauled in all essential mechanical components. New PC, new label printer, etc. in 2023 Technical Specifications and Description: Base machine: Pressure beam saw Version: Fence on the right Saw cycle: away from the fence Cutting length: 5,850 mm Cutting width: 5,850 mm Saw Blades: Main saw blade Ø 400 x 4.4 x 30 mm, Z72, FZ/TZ (not included!) Tungsten carbide pre-scoring blade Ø 180 x 4.4/5.4 x 30 mm, conical (not included!) Cutting Height Cutting height: 110 mm Saw blade projection: 120 mm Pressure beam: pneumatic, pressure adjustable Extraction: Central moving dust channel on the unit Extraction port base machine: 1x Ø 160 mm, positioned on the right side Dust channel in pressure beam: 2x Ø 120 mm – 1x top left, 1x top right with cutting length 5,850 mm: 3x Ø 120 mm – 1x top left, 1x top center, 1x top right Extraction air velocity: 30 m/s Air volume: 4,000 m³/h at 30 m/s Compressed Air Air consumption approx. 32 l/min at 6 bar per cutting cycle Switchable collet chuck pressure Switchable from the control panel Kedjw I Uxpepfx Affenf For sensitive panel materials Automatic cutting length limitation The saw unit detects the workpiece end using a non-contact sensor and optimizes the cutting cycle Offcut device For cutting without leftover piece Clamps retract into recessed pressure beam Width Stop Precision-guided, freely programmable width stop with clamps Rack-and-pinion drive for precise positioning With surface-hardened linear guides Return speed of panel pusher: 80 m/min Forward speed of panel pusher: 80 m/min (EU – max. permissible forward speed 25 m/min) Max. opening for clamps: 120 mm for longitudinal and cross cuts Clamps, floating design Compensate for internal stress in panel packs upwards – 6 pcs for 3,250 mm cutting length – 7 pcs for 4,250 mm cutting length – 8 pcs for 5,850 mm cutting length Control CUTCONTROL 2 with 15" TFT display Operating system Windows 2000 RJ45 network connection 10/100 Base-T Fast Ethernet Intel Celeron processor Midi tower US keyboard Optical mouse CD ROM drive Control panel located on fence side Clearly arranged graphic-based operator interface for easy handling and order/material management on Windows basis Realtime display Large, clearly structured buttons All functions accessible from one level No limits in input fields and unlimited job inputs possible Control Functions Direct Cut: Cutting by direct entry of cutting dimensions. Processing of absolute, serial, or format cuts, with integrated grooving, notching, or positioning cuts. Unlimited jobs programmable. Job prioritization (prioritization possible at any time). Order programming parallel to cutting. NC Cut: Processing of optimized jobs. Graphical machine overview with machine process flow function ...

Condition: used, Numerical Control OSI Working dimensions mm 4300 x 2200 Automatic rear load with lifting table (mm) 4300 x 2200 Max blade protrusion (mm) 125 System for lifting and rotating the panels inside the machine Device for cutting thin panels (4 mm approx ) N. 10 pliers on the upper main pusher carriage N. 4 pliers mounted on the lower independent pusher carriage Twin Pusher Double lateral aligner Scoring group (max blade diameter / power) 180 / Kw 2,2 Main blade group (max blade diameter / power) 430 / Kw 15 Adjustable speed of the blade carriage (m / min) 1 - 150 N. 4 front benches for panel discharge air veil Knedoxt Sgtopfx Affjf

Condition: new, Cesurbend Mandrel Bending Machine / Tube Bending Machine PBNC-65 Technical Specifications Max. Tube Diameter (mild steel): 63 mm Max. Tube Wall Thickness (mm): 3 Max. Bending Angle (°): 190 Tube Bending Rate (rpm): 7–10 Max. Hydraulic Pressure (bar): 200 Max. Bending Radius (mm): 250 Min. Bending Radius (mm): 45 Tube Length (mm): 3500 Bending Tolerance (mm): ± 0.25 mm Bending Motor Power (kW): 7.5 Hydraulic Motor Power (kW): 4 Oil Tank Capacity (L): 50 Machine Width (mm): 1450 Machine Length (mm): 4250 Machine Height (mm): 1200 Machine Weight (kg): 1600 Features • 4-way adjustable gauge • Chain bending system • Gear motor • Touchscreen control panel • Foot pedal operation • Hydraulic mandrel movement • Hydraulic damping function • Hydraulic compression function • Hydraulic pusher • Four cylinders • 7" touch color display • 15 sequential twist positions Kodpfx Afjxt Rdwefonf • 100 program memory capacity • Omron PLC control

Condition: like new (used), Year of construction: 2023, operating hours: 35 h, functionality: fully functional, machine/vehicle number: 8147, power: 160 kW (217.54 HP), rotational speed (max.): 179 rpm, Features: - Enclosed hopper with suction point - Pusher with profiled cutting chamber floor - Safety lines for hydraulics, machine operation down to -25°C - Wear protection package (checkered pattern) Kodpsxup A Iofx Affenf - Electrical integration of belt conveyor (3 kW–11 kW) - Bus connection to external control system - Power control with frequency converter incl. air conditioning - Energy measurement module - Control cabinet enclosure suitable for temperatures down to -25°C

Condition: like new (used), Year of construction: 2015, I sell the automatic CNC working centre for wooden constructions Hundegger K2i. Kedoxtxkxepfx Affonf Almost new machine. Year 2011. Under-table rotary saw with saw blade from 750 mm to 800 mm, 360 degree rotation, servohydraulic tilting 0 – 65 degrees universal 5-axis unit equipped with cylindrical milling cutter, end mill and end mill, milling head diameter 350 mm x 100 mm end mill combi support for at least 5 tools with horizontal drilling device up to power from 2.5 to 3.0 kW, drilling diameter max 24 mm, drill length min 460 mm, machining depth min 300 mm combi support for at least 5 tools with horizontal drilling device up to power from 2.5 to 3.0 kW, drilling diameter max 24 mm, drill length min. 460 mm, machining depth min. 300 mm positioning and gripping of the material using arms, which, while the material is measured, transported to the desired location, the arms keep the processed element as close as possible to the tool that processes it for stability. the processed material can be rotated automatically tolerance +/- 2 mm at a length of 13 m Fully automatic wood input with input roller track and input and sliding cross conveyor K2i: Under-table tilting cross-cut saw K2i: Universal milling unit – 4-axis (UF4) K2i: Kombisupport for vertically working tools K2i: Drilling device (2.2 kW) – vertical drilling direction K2i: Kombisupport for horizontally working tools K2i: Drilling device (2.2 kW) – horizontal drilling direction K2i: Marking tool (rear or on the user side) K2i: Fully automatic element rotation – hydraulic K2i: Transport and positioning system “two-hand system” K2i: Electronic connection K2i: Roller track for removal wooden elements with a pusher K2i: 5-arm storage table K2i: Safety device K2i: Higher quality upper surface of the machine K2i: Extension of the K2i frame to 13.56 m K2i: 5-axis universal milling unit - UF5 (increase to 4-axis) K2i: Remote maintenance (including portable video camera) K2i: Dovetail milling machine (with rotating knives) 60x28x16.5 Suitable for wooden house constructions! Available immediately.

Condition: used, machine/vehicle number: 006211, Max. panel width: 4300 mm Max. panel length: 2200 mm Knedpfxsiwbfue Affef Main saw blade projection: 135 mm No of Grippers: 10 Second flexible pusher: yes Panel Rotation Station: yes

Condition: new, Year of construction: 2021, operating hours: 4 h, functionality: fully functional, machine/vehicle number: ZSS8501604002, overall weight: 4,290 kg, rotor diameter: 387 mm, number of blades: 40, rotor length: 850 mm, rotor width: 457 mm, power: 40.75 kW (55.40 HP), type of input current: three-phase, rotational speed (max.): 80 rpm, rotational speed (min.): 74 rpm, year of last overhaul: 2025, sieve perforation: 60 mm, warranty duration: 6 months, input voltage: 400 V, Single-rotor shredder ZERMA ZSS 850-E 37 kW Hopper opening (mm): 1340 x 840 mm Usable cutting chamber: 690 x 730 mm Rotor diameter x width (mm): Ø 387 x 850 mm Rotor speed: 80 rpm Rotor model: E SEW oil-bath gearbox: Included Number and size of knives: 40 / 34x34x22 mm Knife holders with bolts: Included Number of counter-knives: 1 row of 3 IE3 motor power: 37 kW Screen perforations: > 40mm (to be specified) Hydraulic screen opening: Included Discharge height: 560 mm Connected electrical power: 400 V +/- 5% / 50 Hz Hydraulic pusher power: 3.6 kW Hydraulic pusher with 2 speeds: Included Adherent front plate (ram): Included Air/Oil heat exchanger mounted on hydraulic tank Knodsxtp Dijpfx Affjf Overall length: 2085 mm - Overall width: 1940 mm - Height: 2435 mm Approximate weight (kg): 4400 kg Control cabinet with SIEMENS PLC and settings menus such as: Recipes, Maintenance, Alarms, etc. Cable length to control cabinet: 5 meters See technical datasheet and/or attached diagram for more details.