Used Pneumatic Stapler for sale (8,133)

Condition: repair required (used), Year of construction: 2015, machine/vehicle number: 1464, Offer 26166 - Screw compressor with defective drive motor Manufacturer: KAESER, Type: SK 22 Machine No.: 1464, Year of manufacture: 2015 - SIGMA Control - Operating hours approx. 15,933 h - Load hours approx. 7,654 h - Operating pressure 11 bar - Delivery rate 1.67 m³/min - Drive 400 V / 11 kW - Space requirement approx. W 780 x H 1030 x D 850 mm - Weight approx. 300 kg - Compressed air tank Manufacturer: OKS, Type: 500L Machine No.: 462811, Year of manufacture: 1998 - Tank volume 500 L - Compressed air dryer Manufacturer: JÄGER, Type: ERD 150 Machine No.: 1268, Year of manufacture: 2011 Kdjdpfx Aezg Uh Tsh Eot - Refrigerant R134 A - Cooling air volume 150 m³/h - Oil-water separator

Condition: excellent (used), Year of construction: 2012, Pressing force 28 kN Min./max. operating pressure 3 / 6 bar Stroke 12 mm Electrical connection 220 Volt Overhang 130 mm Kodpfxezmxato Ah Eedt Table 200 x 150 mm

Condition: like new (used), Year of construction: 2007, power: 5.5 kW (7.48 HP), For sale is a Solid Air piston compressor (2-cylinder version, 5.5 kW, 2007) in excellent, technically flawless condition – including a matching 500 L compressed air tank (2007). A special feature of this compressor: it was used exclusively as an emergency unit, so it has hardly been run. Accordingly, it has very few operating hours and is in almost new condition, both technically and visually. The compressor has always been regularly serviced, is fully functional, has been inspected, and is ready for immediate use. The included 500 L compressed air tank ensures a consistent, pressure-stable air supply and, by reducing the number of switching cycles, also protects the compressor. Technical data: - Type: Piston compressor, 2-cylinder - Motor power: 5.5 kW - Compression pressure: 10 bar Ksdjzlhp Uspfx Ah Esdt - Displacement flow rate: 916 l/min - Operating speed: 850 min⁻¹ - Compressed air tank: 500 L (included) - Operating hours: very low (used only as an emergency unit) With our comprehensive all-inclusive package, we will personally take care of the complete service for you – from delivery to the commissioning of your new compressor. This includes unloading, setting up, and aligning the system. Our experienced service technicians will then professionally commission the system, carry out all necessary functional tests, and ensure that your Solid Air compressor, together with the 500 L tank, runs reliably and efficiently. In addition, we offer individual training for your employees so that you can use the system optimally from the start. We will also continue to be available to you after installation – whether for maintenance, technical questions, or future expansions. With our comprehensive all-inclusive package, you don't have to worry about anything – we will ensure that everything runs smoothly and that you can focus entirely on your production. Our service promise: Quality, competence, and customer satisfaction are our top priorities. Our team consists of qualified and experienced technicians who specialize in compressed air and compressor systems, as well as other machines. We place great value on personal support and will be happy to assist you at any time, even after the purchase. In addition, you have the opportunity to inspect and test the system at any time in our workshop. You are cordially invited to come and see the condition and operation of the system for yourself. You are in the best hands with us – professional, reliable, and with a passion for machines! PS CNC Service Germany GmbH & Co. KG All information is subject to change without notice.

Condition: good (used), Year of construction: 1999, machine/vehicle number: 165236.1, Offer 25418 Technical data: - Pressing force approx. 110 kN - Working stroke approx. 50 mm - Force stroke 12 mm Kdsdpfszfh Hyjx Ah Est - Overhang approx. 150 mm - Table size 280 x 180 mm - Adjustable installation height up to max. 300 mm - 2 manual controls - Air inlet 6 - 8 bar - Total space requirement approx. W 600 x H 2500 x D 900 mm - Weight approx. 400 kg

Year of construction: 2007, condition: excellent (used), Control: STE 328-89-1 1/2" complete TOX power pack: S75.160.200.12D table size: 996 x 695 mm installation height: 600 mm total stroke: 150 mm Power stroke: 10 mm Weight: 5700 kg Kedpep Aul Aofx Ah Ejdt Electrical connection 230 V

Condition: used, Well-maintained firstAIR FAS37 rotary screw air compressor (Eucomp Germany airend, ALMiG Kompressoren GmbH brand). Ksdpfx Ahez Anybj Esdt Technical specifications: Type: FAS37 (rotary screw compressor) Year of manufacture: 2020 (01/2020) Motor power: 37 kW / 400V / 50Hz Free air delivery: 5.10 m³/min (180 CFM) Max. working pressure: 10 bar (10.5 bar) Net weight: 880 kg Dimensions: 1000×1250×1310 mm Motor: Smotor IE3, three-phase asynchronous, 2955 rpm

Condition: used, Year of construction: 2001, 2001 Ceccato RL60/10 Compressor 10 bar Kdodez Ahhfspfx Ah Eot

Condition: ready for operation (used), Year of construction: 2009, functionality: fully functional, machine/vehicle number: API607459, overall weight: 1,580 kg, power: 55 kW (74.78 HP), volume flow: 637.2 m³/h, operating pressure: 7 bar, pressure (max.): 7.3 bar, type of cooling: air, Equipment: refrigerant dryer, Atlas Copco GA55+ FF screw compressor – 55 kW – manufactured in 2009 For sale: a well-maintained Atlas Copco GA55+ FF screw compressor with an integrated air dryer. The compressor has already been serviced and is ready for immediate use. Specifications: Type: Atlas Copco GA55+ FF Year of manufacture: 2009 Kjdpfxezku Ube Ah Eedt Motor power: 55 kW / 75 hp Capacity: 10.62 m³/min Working pressure: 7.3 bar Motor speed: 2,978 rpm Weight: approx. 1,580 kg Operating hours: 17473/4022 Equipped with an integrated air dryer Serviced and ready for use This compressor is suitable for industrial applications that require a reliable compressed air supply. Optionally available with a new or used compressed air tank.

Condition: excellent (used), Year of construction: 2004, Ultrafilter LP 0072 Compressed Air Treatment Dryer Industrial adsorption dryer and CO₂ purifier from premium manufacturer Ultrafilter (Donaldson) This unit was specifically developed for applications requiring ultra-high-purity compressed air—ideal for operating laser cutting systems, as well as for use in the pharmaceutical, food processing, and electronics manufacturing industries. Using a 5-stage process, the system not only removes moisture but also highly efficiently purifies the compressed air of oil vapors, particles, and carbon dioxide (CO₂). Technical specifications at a glance: - Manufacturer: Ultrafilter (Donaldson) - Model: LP 0072 - Power supply: 230 V / 50 Hz - Medium: Compressed air - Volume flow (at 5.5 bar g): Inlet approx. 36.3 m³/h | Outlet min. 13.5 m³/h - Operating pressure: min. 5.5 bar g | max. 16 bar g - Temperature range (medium/ambient): max. 40°C - CO₂ purification: Inlet max. 1000 ppm → Outlet max. 100 ppm - Vessel test pressure: 20.8 bar - Year of manufacture: 2004 Dimensions: (H x W x D) 2000 x 600 x 800 mm Kedpfszwl Rgex Ah Eodt We would be happy to offer you suitable bank financing for your project. komplett-konzept.leasingo.de You can find more items—both new and used—in our shop! International shipping costs available upon request!

Condition: used, Year of construction: 2024, operating hours: 698 h, functionality: fully functional, machine/vehicle number: APP889037, overall weight: 3,500 kg, total length: 5,760 mm, total width: 1,987 mm, total height: 1,973 mm, motor manufacturer: Cummins B6,7, power: 231 kW (314.07 HP), fuel type: diesel, volume flow: 19 m³/h, pressure (max.): 25 bar, Equipment: type plate available, We are offering this used Atlas Copco X-Air+ 750-25 reciprocating compressor, manufactured in 2024, for sale. Model: X-AIR+ 750-25 Max. operating pressure: 25 bar Speed: 1920 rpm Engine power: 231 kW Permissible total weight: 3500 kg Kdedpfx Aez A Dauoh Est Support load: 70 kg Axle load, axle 1: 1765 kg Axle load, axle 2: 1665 kg Serial number: APP889037 Date of manufacture: 05/2024 If you have any questions or require further information, please do not hesitate to send us a message or call us.

Condition: excellent (used), Year of construction: 2007, operating hours: 9,667 h, PROD. KAESER TYPE ASD57 T Kdjdpfx Ahsztqvyo Est S/N 1187 YEAR 2007 POWER (kW) 30 CAPACITY (m3/min) 4.65 PRESSURE (bar) 8 HOURS (RUNNING/TOTAL) 9667/21953 VARIABLE FREQUENCY DRIVE no BUILT-IN DRYER yes, R134a 1.1kg HEAT EXCHANGER no COOLED BY (AIR/WATER) air ON TANK no DOCUMENTS no CONNECTION 1 1/2 NEW/USED USED

Condition: excellent (used), Year of construction: 2022, functionality: fully functional, power: 15 kW (20.39 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 175 t, stroke length: 275 mm, operating speed: 12 mm/s, reverse speed: 190 mm/s, table length: 3,100 mm, table height: 900 mm, throat depth: 410 mm, distance table to ram: 550 mm, clearance between the columns: 2,600 mm, oil tank capacity: 300 l, total length: 5,025 mm, total width: 2,150 mm, total height: 2,680 mm, overall weight: 9,086 kg, Equipment: CE marking, documentation/manual, safety light barrier, 2022 Ermaksan Speed-Bend PRO 3100x175 CNC Press Brake 2022 Ermaksan Speed-Bend PRO 3100x175 CNC press brake in very good condition. 175T x 3100mm, 6 axis, Delem DA66TX, CNC crowning, laser guards, tooling included. Machine Manufacturer: Ermaksan Model: Speed Bend Pro 3100 x 175T Machine Type: 6 Axis CNC Pressbrake Capacity: 3100 x 175T Year: 2022 Control: Delem DA66TX Condition: Very Good Description Ermaksan Speed-Bend Pro 6 Axis CNC Hydraulic Press Brake with Delem DA66TX Control. Available now, this 2022 Ermaksan Speed-Bend PRO 3100x175 CNC Press Brake is a high-quality, modern hydraulic press brake in very good condition. This is a 6 axis machine with Y1, Y2, X, R, Z1 and Z2 axes, fitted with a Delem DA66TX CNC control, pneumatic top tool clamping, CNC crowning, laser guards, wanderer type foot pedal, and supplied with top and bottom tooling. Ideal for sheet metal fabrication, precision bending, stainless steel work, mild steel fabrication, aluminium bending, agricultural fabrication, general engineering and production workshops. Key Features 2022 Ermaksan Speed-Bend PRO 3100x175 175 tonne bending capacity 3100mm bending length 6 axis CNC press brake Y1, Y2, X, R, Z1 & Z2 axes Delem DA66TX CNC control Pneumatic top tool clamping Top and bottom tooling included CNC / motorised crowning Laser safety guards Wanderer type foot pedal Very good condition Excellent machine for fabrication and production bending work Capacity & Main Machine Data Manufacturer: Ermaksan Model: Speed-Bend PRO 3100x175 Year: 2022 Machine Type: CNC hydraulic press brake Bending Length: 3100mm Bending Force: 175 tonnes Distance Between Columns: 2600mm Axes: Y1, Y2, X, R, Z1, Z2 Crowning: Motorised / CNC crowning Backgauge Finger Blocks: 2 Speeds & Axis Travel Y Rapid Speed: 180mm/s Y Working Speed: 12mm/s Y Return Speed: 190mm/s X Axis Travel: 800mm X Axis Speed: 500mm/s R Axis Travel: 250mm R Axis Speed: 350mm/s Z1 / Z2 Axis Travel Speed: 1000mm/s Stroke, Daylight & Frame Stroke: 275mm Daylight: 550mm Throat Depth: 410mm Table Height: 900mm Table Width: 90mm Power, Size & Weight Oil Capacity: 300 litres Motor Power: 15kW Approx. Length: 5025mm Approx. Height: 2680mm Kdedpjz Dn Husfx Ah Eot Approx. Width: 2150mm Approx. Weight: 9086kg Delem DA66TX CNC Control Control Features Include 2D graphical touch-screen programming High-resolution colour TFT display Automatic bend sequence calculation Collision detection 3D machine setup with multiple tool stations USB / peripheral interfacing Product and tool memory Profile-TL offline software support User-friendly Delem touch navigation Delem’s DA-66T platform is listed by Delem as a 2D graphical press brake control with automatic bend sequence calculation, collision detection, full 3D machine setup, USB interfacing, 17" high-resolution colour TFT display and Profile-TL offline software support. Included Equipment Pneumatic top tool clamping Top tooling Bottom tooling CNC crowning Laser guards Wanderer type foot pedal 6 axis CNC backgauge system Delem DA66TX control Typical Applications Sheet metal fabrication CNC press brake bending Mild steel bending Stainless steel bending Aluminium bending Box and pan type components Architectural metalwork Agricultural fabrication General engineering workshops Production bending work

Condition: excellent (used), Year of construction: 1999, operating hours: 43,019 h, functionality: fully functional, machine/vehicle number: 1127, overall weight: 750 kg, total length: 1,610 mm, total width: 970 mm, total height: 1,380 mm, power: 37 kW (50.31 HP), volume flow: 366 m³/h, operating pressure: 8 bar, pressure (max.): 10 bar, type of cooling: water, Equipment: documentation/manual, type plate available, KAESER BS61 Screw Compressor 37kw 6.1m3/min 7.5bar. compressor For sale KAESER BS61 screw compressor in excellent condition. Maintained from new, serviced throughout. last major service performed at 86009 operating hours Manufacturer: Kaeser BS61 Year of manufacture: 1999 serial number: 1127 Operating pressure: 7.5bar Power: 37 kW Capacity: 6.1 m3/min 366 m3/h Operating hours: standby: 86033h loaded: 43019 h Kedpfxeydr Igs Ah Eedt Sigma Control control. engine speed: 1500 rpm Overall dimensions: 1610 x 970 x 1380 mm Tail weight: 750kg

Condition: excellent (used), Year of construction: 2018, operating hours: 81,265 h, functionality: fully functional, volume flow: 1,380 m³/h, type of cooling: air, pressure (max.): 16 bar, Equipment: type plate available, Used Kaeser TF 230 refrigerant dryer 23 m3/min Kodjzupp Uepfx Ah Eodt 16 bar Year of manufacture: 2018

Condition: excellent (used), Year of construction: 2009, operating hours: 4,824 h, functionality: fully functional, power: 5.52 kW (7.51 HP), 1 x Atlas Copco Airpower B.V. rotary screw compressor and refrigerant air dryer mounted on 200L receiver tank. Manufacturer - Atlas Copco Airpower B.V. Model - GX5 FF. Kedpfx Ahszu Aw Se Eodt Serial number - CAI361147. Date of manufacture - 2009. Working pressure - 10 bar. Working hours - 4824 hours. Electrical requirements: Compressor - 400 V / 50 hz / 3 phase. Air dryer - 230 V / 50 hz / 1 phase.

Condition: excellent (used), Year of construction: 2018, operating hours: 513 h, functionality: fully functional, overall weight: 649 kg, power: 33 kW (44.87 HP), fuel type: diesel, Atlas Copco XAHS 38/XAS88/Compressor/Construction Compressor/12 Bar • Manufacturer: Atlas • Model: Copco XAHS 38/XAS88 • Year of manufacture: 2018 • Operating hours: 513 hours Kedpfx Ahjz A Dq Ts Eedt • Power: 33 kW/44 hp • Engine: Kubota 4-cylinder diesel engine • 12 bar • Transport length: 1.94 m • Transport width: 1.16 m • Transport height: 1.05 m • Total weight: 649 kg • German machine • Immediately ready for operation • This offer is non-binding and subject to change. - Subject to prior sale, - Errors and/or typos not excluded. - Sale subject to our general terms and conditions.

Condition: new, functionality: fully functional, machine/vehicle number: 0700, empty load weight: 4,100 kg, maximum load weight: 50,000 kg, overall weight: 54,100 kg, axle configuration: 4x2, first registration: 09/2026, next inspection (TÜV): 09/2027, loading space length: 5,000 mm, loading space width: 2,200 mm, loading space height: 880 mm, total length: 6,000 mm, total width: 2,200 mm, total height: 880 mm, tire size: 559x356, tire condition: 100 %, maximum speed: 6 km/h, color: orange, Year of construction: 2026, Heavy-duty transport trailer with a payload of 50,000 kg on 60% of the loading area at 6 km/h. Dimensions: 5000 x 2200 x approx. 880 mm. Transport floor: 50 mm wood. Tyres: banded wheels 559 x 356, 8-wheel configuration. Steering: all-wheel steering with adjustable track and steering rod. Drawbar head at both front and rear for coupling bar. Trailer can be operated in both driving directions. Paint finish: RAL 2000. Four welded lashing eyes per longitudinal side. Accessories: double-acting wheel chock. Documentation attached in a box on the frame. Reflectors on three sides. Towing bar 2000 mm with anti-fall safeguard and height adjustment. Kedpjyq Rr Refx Ah Eedt

Condition: like new (used), functionality: fully functional, total height: 150 mm, jaw height: 40 mm, clamping width: 160 mm, clamping range: 200 mm, clamping length: 200 mm, - Extremely stable and robust Kodpox Rp Ekofx Ah Esdt - pneumatic - barely used - 5 units available - New price over 5,000 euros

Condition: used, Year of construction: 2008, operating hours: 22,795 h, machine/vehicle number: 5039, overall weight: 600 kg, power: 18.5 kW (25.15 HP), type of cooling: air, Equipment: documentation/manual, type plate available, Frequency-controlled screw compressor with integrated heat recovery Manufacturer: Kaeser Type: ASD 32 Delivery rate: 8 bar - 3.2 m³/min Motor power: 18.5 kW Kedpjw Trghofx Ah Ejdt Compressed air connection: G 1¼ Max. available thermal output: 16.4 kW Includes complete documentation + CE certificate Next maintenance at 24,360 operating hours Weight: 600 kg Required space: 1350 x 921 x 1505 mm (L x W x H) The machine can be demonstrated on site. All information subject to change. Prior sale reserved.

Condition: excellent (used), Year of construction: 2010, functionality: fully functional, type of input current: three-phase, overall weight: 2,000 kg, input voltage: 400 V, total width: 1,650 mm, total length: 2,200 mm, total height: 4,250 mm, filter area: 286 m², suction capacity: 18,000 m³/h, negative pressure: 3,500 Pa, input frequency: 50 Hz, Equipment: type plate available, Dust extraction unit, fume extraction unit for welding, self-cleaning cartridge filter, pneumatic, vacuum-operated for plasma, laser, sandblasting, soda blasting, shot blasting, and for all types of dry dust. The filter is pneumatically cleaned with pulses of compressed air during operation, resulting in high device efficiency. The fan is located on the clean air side, minimizing the risk of explosion. Brand: Donaldson Torit DCE Model: DFPRO 16 Kdodpfx Ahjz Ayv Ue Eot Year of manufacture: 2010 Cartridge filter elements, oval - DFO ULTRA-WEB FR - 16 pcs Filtration area: 286 m2 Fan power: 18.5 Kw Fan model: FR 501 Built-in frequency converter. Remote monitoring of the device is possible thanks to Donaldson's iCue technology. Capacity up to 18000 m3/h Inlet diameter: 630 mm Noise silencer included. New filter elements, custom-made according to the device's intended use, are also available on request. Stock number: 1155

Condition: like new (used), Year of construction: 2023, operating hours: 50 h, functionality: fully functional, feed length X-axis: 2,020 mm, feed length Y-axis: 3,020 mm, feed length Z-axis: 70 mm, travel distance X-axis: 2,020 mm, travel distance Y-axis: 3,020 mm, travel distance Z-axis: 70 mm, quill stroke: 160 mm, quill travel distance: 160 mm, total width: 3,020 mm, total length: 2,020 mm, table width: 3,020 mm, table length: 2,020 mm, table height: 200 mm, working range: 70 mm, space requirement width: 3,020 mm, space requirement length: 2,020 mm, space requirement height: 200 mm, We offer this as new VHF CAM 2030 milling machine, year of construction 2023. Machine is in perfect condition, unused. Equipped with following accessory: CAM 2030 active Pro (2020 x 3020 x 70mm) - with special vacuum table -Passage height 200 mm, lift 160 mm -SPC 2300P with pneumatic chucking device Kdjdpfx Ahjz Dfxne Eot -Tool change station for 4 cones WK 19 for SPC 1500P/SPC 2300P -Industrial vacuum cleaner (48 l capacity), dust category M, Autoclean -Dust extraction unit for WK 19-50 -Cooling and spraying unit -Automatic z adjustment -System rack for integration of controllers and computer system -Cenon CAM-software with CCD camera If you have any questions or need more information, feel free to send us a message or give us a call.

Condition: excellent (used), Year of construction: 2002, Ultrafilter LP 0072 Compressed Air Treatment Dryer Kedpozwmacsfx Ah Eodt Industrial adsorption dryer and CO₂ purifier from premium manufacturer Ultrafilter (Donaldson) This unit was specifically designed for applications requiring ultra-high-purity compressed air—ideal for operating laser cutting systems, as well as for use in the pharmaceutical, food, and electronics manufacturing industries. Using a 5-stage process, the system not only removes moisture but also highly efficiently purifies the compressed air of oil vapors, particles, and carbon dioxide (CO₂). Technical specifications at a glance: - Manufacturer: Ultrafilter (Donaldson) - Model: LP 0072 - Power supply: 230 V / 50 Hz - Medium: Compressed air - Volume flow (at 5.5 bar g): Inlet approx. 36.3 m³/h | Outlet min. 13.5 m³/h - Operating pressure: min. 5.5 bar g | max. 16 bar g - Temperature range (medium/ambient): max. 40°C - CO₂ purification: Inlet max. 1000 ppm → Outlet max. 100 ppm - Vessel test pressure: 20.8 bar - Year of manufacture: 2002 Dimensions: (H x W x D) 2000 x 600 x 800 mm We would be happy to offer you suitable bank financing for your project. komplett-konzept.leasingo.de You can find more items—both new and used—in our shop! International shipping costs available upon request!

Condition: good (used), Year of construction: 2004, operating hours: 35,000 h, functionality: fully functional, power: 15 kW (20.39 HP), type of cooling: air, Equipment: refrigerant dryer, Almig screw compressor flex 15 Drive (year of manufacture 2004) – including MDX 3600 air dryer (year of manufacture 2011) – well-maintained, inspected, and ready for use. Kdjdezlgmfspfx Ah Eot For sale is an Almig screw compressor flex 15 Drive (year of manufacture 2004, 15 kW power) in well-maintained, technically flawless condition – including a matching MDX 3600 air dryer (year of manufacture 2011). The compressor has been regularly maintained and is in very good condition both visually and technically. It is fully functional, inspected, and ready for immediate use. The included MDX 3600 air dryer reliably provides dry, clean compressed air, thus protecting your downstream equipment and tools. With our comprehensive all-inclusive package, we can personally take care of the complete service for you – from delivery to commissioning of your new compressor. This includes unloading, installing, and aligning the system. Subsequently, our experienced service technicians will professionally commission the system, perform all necessary functional tests, and ensure that your Almig flex 15 Drive, together with the MDX 3600 air dryer, runs reliably and efficiently. In addition, we offer individual training sessions for your employees so that you can optimally utilize the system from the very beginning. We will also be happy to continue to support you after installation – whether for maintenance, technical questions, or future expansions. With our comprehensive all-inclusive package, you don't have to worry about anything – we ensure that everything runs smoothly and that you can focus entirely on your production. Our service promise: Quality, competence, and customer satisfaction are our top priorities. Our team consists of qualified and experienced technicians who specialize in compressed air and compressor systems, as well as other machinery. We place great emphasis on personal support and are always happy to assist you even after the purchase. You also have the opportunity to inspect and test the system at any time in our workshop. You are cordially invited to come to our location and see for yourself the condition and functionality. With us, you are in the best hands – professionally, reliably, and with a passion for machines! PS CNC Service Germany GmbH & Co. KG All information without guarantee.

Condition: good (used), Year of construction: 2023, functionality: fully functional, operating hours: 59,000 h, input voltage: 400 V, input frequency: 60 Hz, type of input current: three-phase, workpiece height (max.): 50 mm, edge thickness (max.): 5 mm, actuation type: electric, total height: 2,000 mm, total length: 3,095 mm, total width: 1,330 mm, overall weight: 700 kg, Equipment: documentation/manual, 2023 Good condition For inquiries, please contact: Gergely Repka 06707739050 Professional edge banding machine suitable for edge sealing and post-processing of panel-format sheet materials. It can be used for particleboard, MDF, furniture board, table tops, etc. Key technical data: * Coil edge banding: 0.4–3 mm * Strip edge banding: 0.4–5 mm * Maximum edge height: 55 mm * Processable sheet thickness: 8–50 mm * Edge banding cross-section: max. 5 × 50 mm (material-dependent) * Minimum workpiece width: 70 mm * Minimum workpiece length: 180 / 210 mm * Feed speed: 9 m/min * Manually adjustable pressure beam Kdjdpfx Aszi Am Nsh Ejt * Extendable workpiece support with 500 mm distance Equipment: * Edge Control BC15 control system with a 15.6" touchscreen * Vi.se. (Visual Setting) digital setting system for quick and accurate machine adjustment * FG101 pre-milling unit with 2 diamond milling heads * MG101 edge feeding unit * Glu Jet GJ101 hybrid adhesive technology (2.3 kW / 50 Hz) with automatic adhesive height adjustment * 1.4 kg adhesive tank (for 4 cartridges) * Glu Jet cleaning tank * Automatic refilling system * DW101 pressing unit * KA101 pneumatic end trimming unit, 1 motor version * 0.22 kW * 12,000 rpm * FR101 profile smoothing unit * chamfering and radius function * 2 × 0.37 kW * 12,000 rpm * 2 replaceable HW milling heads Ø75, Z4, R2 * FF101 corner rounding unit with dual linear guide * ZK101 scraping unit R=2.0 mm * Chip collection system * FK101 surface scraper unit * SW101 polishing unit * 2 × 0.13 kW * 1,400 rpm * 2 textile polishing discs, 120 mm * Adjustable from 0–5° * TR101 spraying unit for infeed and outfeed sides

Condition: used, Year of construction: 1999, functionality: fully functional, operating pressure: 10 bar, We offer this used Ceccato RL 40/10 reciprocating compressor, manufactured in 1999. Kedpfjzxna Hsx Ah Esdt If you have any questions or require further information, please do not hesitate to send us a message or call us.