Used Pneumatic Press Stanze With Tools for sale (49,030)

Condition: as good as new (ex-display), Year of construction: 2025, operating hours: 2 h, functionality: fully functional, machine/vehicle number: L030748, overall weight: 2 kg, warranty duration: 3 months, pressure: 7 bar, The Scell-it® E-312NP pneumatic riveting tool for self-clinching nuts offers reliability, precision, and functionality, making the installation of self-clinching nuts quick and easy. Below, we provide additional information regarding the replacement of the nose/mandrel, stroke adjustment, and self-clinching nut installation, to enable you to fully utilize the potential of this tool. Nose/Mandrel Replacement: Detailed instructions for replacing the nose and mandrel can be found in our comprehensive operating manual. If you intend to use self-clinching nuts of different diameters, it will be necessary to change the nose, mandrel, and adjust the tool accordingly. Consult the instructions to learn how to make these changes and adjust the mandrel length to the size of the self-clinching nut. Self-Clinching Nut Installation: Fodszc Dx Ispfx Ad Iopi After performing the startup procedures and adjusting the stroke, insert the self-clinching nut into the pre-drilled hole. Place the mandrel in the self-clinching nut and press the tool. The mandrel will automatically seat itself in the self-clinching nut. Press the tool trigger to clamp the self-clinching nut onto the component. The release will occur automatically after the self-clinching nut has been clamped onto the component, allowing you to release the tool. If the tool is not released from the self-clinching nut, press the button on the back of the tool to force the release. Stroke Adjustment: The tool stroke must be adjusted to the component on which the self-clinching nut will be clamped. The E-312NP riveting tool allows stroke adjustment from 1 mm to 7 mm. To adjust it, follow the instructions below: Precise stroke adjustment is crucial for effective self-clinching nut installation. Here are some tips for controlling stroke adjustment: The stroke can be set from 1 mm to 7 mm. The graduated scale on the tool accurately indicates the set stroke. To increase the stroke, move the adjustment slider towards the front of the tool, while simultaneously turning the knob to the left. Then release the slider, ensuring that it is re-seated on the head. The cursor will indicate the range of the set stroke. To decrease the stroke, follow the same procedure, turning the stroke adjustment knob to the right. Our self-clinching nut riveting tool is designed to allow precise stroke adjustment and ensure optimal installation results. If the stroke is incorrectly adjusted or the self-clinching nut has a quality defect, the mandrel release may be difficult. In this case, use the "anti-block rod," which is included in the kit. Insert it into the hole in the base of the sleeve and turn it to the right to release the self-clinching nut, as shown in the illustration in the manual.

Condition: good (used), Year of construction: 2015, functionality: unexamined, - Total stroke: 300 mm Fpsdpswxvwisfx Ad Ioi - Maximum press force: 68.9 kN - Power: 0.3 kW - Min/max air pressure: 3 - 6 bar - Machine weight: 1250 kg

Condition: good (used), Matrices, 100 mm x 2 Offset punches x 2 In good condition Fsdpfjzaitrex Ad Iepi

Condition: good (used), functionality: fully functional, Type DZ 4 Press force at 6 bar 4 t Fjdpfxezck Uvo Ad Iopi Press force at 12 bar 8 t Table size W x D approx. 280 x 280 mm Installation height 350 mm Throat depth 160 mm

Condition: like new (used), Year of construction: 2007, functionality: fully functional, type of input current: AC, pressing force: 1 t, table width: 200 mm, table length: 230 mm, total width: 400 mm, total height: 860 mm, overall weight: 105 kg, air pressure: 6 bar, FCP-C 10KN pneumatic press machine for sale in several pieces manufacturer: FCP-C pressing force 1 ton Stroke: 75-100 (mm) Air pressure 0.2-0.5 MPa Open height 320 (mm). two-hand operation Fsdpfx Aev E Sazod Ijpi table size: 200x230mm Shaft dimensions Bore diameter φ15H9 (mm) x depth 35 (mm). Speed ​​controller Low friction roller Rotation stop lever height: 880mm length: 360mm width:400mm weight: 105kg Many options (timing box with counter, load management device, etc.). ●The lowering speed of the press can be freely adjusted by the speed controller. ●Mechanical stop for bottom dead center adjustment. ●Inching operation valve for smooth forming. ●Air equipment is also standard.

Condition: like new (used), Year of construction: 2018, functionality: fully functional, pressing force: 2 t, table width: 330 mm, table length: 350 mm, throat depth: 100 mm, air pressure: 6 bar, cylinder diameter: 28 mm, For sale in new condition HYUNDAE HP-2000 2t PNEUMATIC PRESS Brand: HYUNDAE MACHINERY & ELECTRIC CO.,LTD Type: HP-2000 manufacturing of year: 2021 Fpodpevbfbwefx Ad Iji Max. pressing force: 2t open height:300mm Bolster Size: 350x330mm Stroke length: 100mm Cylinder diameter: 28mm built on a press stand Two-handed operation Voltage: 110V Air Connecting Hose Diameter:12mm

Condition: used, Technical details: pressure: manuell t stroke: 15 mm machine weight approx.: 8,4 kg dimensions of machine: 600x250x70 mm Pneumatic Cable Terminal Press - application: press of cable terminal on electrical cable and air-conditioning lines futher details: - press cylinder: slide Ø 25mm: outer diameter Ø 68mm: maximum extension length approx 15mm - tool fork: width=30mm ; length=70mm - maunal lever Ø 30 x L:300mm equipment - toolbox with div. round and hexagonal tool jaws i.D. * Fpedpfx Adeu Nfr No Iei

Condition: used, Technical details: Fpodpfsu Nftgex Ad Iei pressure: manuell t distance between columns: - mm stroke: ca. 20 mm machine weight approx.: 9,5 kg dimensions of machine: L: 580 x B:280 x H:80 mm pneumatic cable terminal press - application: press of cable terminal on electrical cable and air-conditioning lines futher details: - press cylinder: slide Ø 25mm: outer diameter Ø 68mm: maximum extension length approx 20mm - tool holder: width=40mm ; length=90mm - maunal lever Ø 30 x L:300mm equipment - toolbox with div. round and hexagonal tool jaws see the picture i.D. *

Condition: good (used), Year of construction: 1999, Pneumatic press, manufacturer: SCHMIDT, type: ZHS-2/22, year of manufacture: 1999. Two-hand operation. UVV certification valid until 2023. Fsdpfx Aoiduvcsd Ijpi

Condition: good (used), CMC Italia Q Finish Crater 20 Book Press Book press with groove cutter and heated platens. Manufactured by CMC, Italy. Technical specifications: Maximum format: 420 x 500 x 80 mm Weight: 420 kg Fjdpfxey Tu Txe Ad Iopi Pressure: 5000 kg Built-in hydraulic unit. Automatic book feed. Automatic format detection. 380V power supply + compressed air.

Condition: used, 1x bending knife from a VOEST press brake Length: 4050 mm Weight: approx. 120 kg Fpodpfx Adjy Tbvms Iji For further dimensions see pictures.

Condition: used, 12-piece die block for GEWA press brake Bending tool for press brake, lower tool Type: 0255/14 V-block size: 16 mm for 90° V-block angle: 88° Fpsdswbvmispfx Ad Iji Die depth: approx. 8 mm Height: 120 mm Max. pressure per meter: 100 t/m Die base width: 60 mm Total length: 4175 mm Segment lengths: 4 x 835 mm, 1 x 400 mm, 1 x 200 mm, 1 x 100 mm, 1 x 50 mm, 1 x 40 mm, 1 x 20 mm, 1 x 15 mm, 1 x 10 mm Weight: 110 kg Very good condition

Condition: used, Pneumohydraulic cylinder TOX Pressotechnik Hydro-pneumatic press, power pack Type: S 04.00.050.12 D No.: 208696.460 Year of manufacture approx. 2000 Pressure capacity: 4.0 tons at 10 bar Pressure capacity: 3.0 tons at 8 bar Pressure capacity: 2.6 tons at 7 bar Pressure capacity: 2.4 tons at 6 bar Pressure capacity: 2.0 ton. at 5 bar Pressure capacity: 1.6 ton. at 4 bar Pressure capacity: 1.2 tons at 3 bar Total stroke: 50 mm Fpsdpfou D Tz Uex Ad Ioi Power stroke: 12 mm Piston rod: Ø 30 mm Thread for piston rod: M22 x 2 mm Compressed air requirement: 3 to 10 bar - Electronic oil pressure switch with TOX digital display for force measurement, type 167282 - Height only power pack with piston rod = 610 mm - Height of power pack hydropneumatic cylinder only = 560 mm - Additional base plate 160 x 160 x 20 mm - Plunger plate: Ø 68 mm Space requirement L x W x H: 160 x 160 x 660 mm Weight: 21 kg Very good condition 3 pieces available, price per piece

Condition: used, Hydraulic Synchronizing Press, Spotting Press AGEO Type GHP 200 H6 4-Column Hydraulic Press, Tool Trial Press, Spotting Press Serial No. 21169 Year of manufacture: 1993 Pressing force: 200 tons Clearance between uprights (front): 1200 mm Upright opening (side): 650 mm Table surface: 1560 x 1010 mm Ram surface: 1560 x 1010 mm Ram stroke: 575 mm Draw cushion stroke: 300 mm Draw cushion holding force: 63 tons Draw cushion ejector force: 30 tons Max. installation height: 775 mm Table height above floor: 1000 mm Guide column Ø: 140 mm Fodpfjwva I Hex Ad Ispi Clamping pin bore in ram: 64 mm Pressing speed: 0 to 10 mm/s, stepless Return speed: 0 to 20 mm/s, stepless Main motor power: 22 kW Control pump motor power: 5.5 kW Connection: 400 Volts, 50 Hz - Table and ram with 22 mm T-slots - Two pressure cylinders with electronic precision synchronization control - Stepless electronic stroke limitation (top and bottom with digital travel measurement and position display) - Mechanical safety support device (prevents ram from dropping due to dead weight) - Single-hand and two-hand operation - Electrical tool safety via signal contact - Pressure presetting independent of stroke (via keypad, digital pressure display) - Travel measurement system right and left via rotary encoders - Electrical control: MS-DOS PC with Ageo H v2.23 control software - Operator panel with swiveling display - Stroke movement and press force adjustable via joystick - Adjacent hydraulic power unit with electrical cabinet - Hydraulic draw cushion under the press table - Draw cushion with ejector function - Continuous stroke control - Floor-level installation - Electrical oil temperature monitoring - Operating manual with circuit diagrams Space required by press (upright) L x W x H: 1800 x 1010 x 3470 mm Space required for horizontal transport L x W x H: 3500 x 1800 x 1200 mm Net weight press: 13 tons Space for hydraulic power unit L x W x H: 1000 x 800 x 3040 mm Net weight hydraulic power unit: approx. 1 ton The machine was used as a tool trial press in a toolmaking workshop. Very good condition.

Condition: used, Double-column hydraulic press, SMG Type HBP 200 - 2000 / 2000 Manufacturer's No. 7.4117, Year of manufacture 1986 - Refurbished 2000 Clamping force 200 tons Column width at the front 2050 mm Column opening on the side 2030 mm Table surface 2800 x 2000 mm Ram surface 2000 x 2000 mm Ram stroke 700 mm Installation height max. 1850 mm Table height above floor 750 mm Ram retraction force 33 tons Rapid traverse speed 500 mm/s Fpedpfx Adodzp Tco Ioi Pressing speed 72/36 mm/s Return stroke speed 420 mm/s Safety clearance 230 mm Main motor power 75 kW Control pump motor power 11 kW Power supply 380 Volt, 50 Hz - 8-fold flat guide for the ram - Clamping plate with 22 mm T-slots on the ram, 2000 x 1900 mm, thickness 60 mm - Hydraulic ram locking in the top dead center position - Linear encoder system with glass scale - Electrical control system renewed in 2000 with SIEMENS PLC S7 - Adjacent control cabinet - 2-hand control panel adjacent - Floor-level installation - Central lubrication - Operating manual with wiring diagrams Space required for the press in upright position L x W x H 3700 x 2900 x 5900 mm Machine height complete with motor 5900 mm Space required for horizontal transport L x W x H 5900 x 3250 x 2950 mm Weight 38 tons The machine was used as a production press at Volkswagen until 2000. From 2000, the machine was used as a tool try-out press in a toolmaking company. Good condition.

Year of construction: 2011, condition: excellent (used), 2 pneumatic shelf presses for edging and veneering. Type PNP Working area: 1250x2500 mm Weight: 1940 kg Presses are fully operational and in use. Fsdpey Avb Aofx Ad Iopi For any questions, please contact: Piotr Żołnierczyk - 606 666 023

Condition: used, 2-station notching machine and folding machine EUROMAC type Multi 220/6R Press brake, press brake, notching machine Serial no. M11941298 Year of manufacture 1998 Cutting capacity 6 mm steel at 45 kg/mm2 4 mm for stainless steel Station I (notching) Notching angle 60° to 140° (with special blade from 30° to 140°) Knife length 220 mm Table size 950 x 640 - Manual angle adjustment via hand wheels - Notching angle with built-in blade set from 60° to 140 - Hydraulic clamping of the upper and lower knives - Automatic cutting gap adjustment - sheet hold-down device - Scaled measuring tapes embedded in the table - stop rails with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 ton Table size 950 x 340 Working height 1100 mm Fedpfemck Ryjx Ad Iopi - stepless lifting speed - Infinitely adjustable stroke limiter - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4x 90° prisms, length = 415 mm - 90° upper tool, length = 415 mm Motor power 4 kW Mains connection 400 Volt, 50 Hz Space requirement L x W x H 1150 x 1050 x 1460 mm Weight approx. 1000 kg good condition

Condition: used, Year of construction: 1986, functionality: fully functional, input voltage: 380 V, input frequency: 50 Hz, pressing force: 204 t, stroke length: 220 mm, table length: 4,000 mm, clearance between the columns: 3,400 mm, overall weight: 12,000 kg, We offer this used PROMECAM Amada STPC 204 200 40 160 press brake, manufactured in 1986. Machine number: STPC 200 40 160 Maximum pressing force: 2,040 kN Maximum stroke: 220 mm Voltage: 380 V Frequency: 50 Hz Date of manufacture: 20.10.86 Bending length: 4 m Distance between uprights: 3.4 m Includes tooling! Machine weight: approx. 12 tons Equipped with CYBELEC DNC 7000 control A crane is available for loading. The machine is functional and still in use / can be tested while powered on. However, due to its age, we cannot offer any warranty. If you have any questions or require further information, please feel free to send us a message or call us. Fpsdpfxey Tmlas Ad Ioi

Year of construction: 2011, condition: ready for operation (used), 2 complete precision press systems are offered. Press force: 220kN, stroke: 100/12mm, operating pressure: 3/6bar, tool holder X/Y: approx. 350mm/300mm, safety distance: 355mm, overrun time: 0.07s, control system SCHMIDT PressControl 500: control type: PRC 500, incl. operating panel with display and keypad, two-hand control according to EN 574 Type III B. Accessories: machine frame with integrated safety device BGR 500 inspection, machine weight: 800kg, inspection possible by arrangement. Fodpfjy S A I Usx Ad Iopi

Year of construction: 2025, condition: new, functionality: fully functional, Partial segment UKB die / lower tool system AMADA 415 mm V16 R2 85° V22 R2.5 85° V35 R3 85° V50 R4 85° Partial segments UKB upper tool system AMADA 415 mm, 150 mm, 35 mm, 15 mm and horn left/right 100 mm R 0.8 / 85° H 66.5 Fpedpoyqyc Sofx Ad Iei Furthermore, we offer a 835 mm die (manufacturer Eurostamp) which is structurally identical to the offered UKB dies. This die is slightly damaged, but fully functional and is offered for €70.00 if interested.

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, C-frame press for clinching technology Pressing force: 4.8 t Air pressure: 6 bar Fpodpfx Adoy Ey Hzo Iei Total stroke: 32 mm Power stroke: 3 mm No tools included

Condition: ready for operation (used), Year of construction: 2007, functionality: fully functional, operating hours: 42,200 h, pressing force: 130 t, table length: 3,230 mm, clearance between the columns: 2,650 mm, total length: 3,980 mm, total width: 1,900 mm, total height: 2,840 mm, overall weight: 10,200 kg, control type: CNC control, Hello, We are selling Trumpf TruBend 5130 CNC press brake, tooling included.. 130t/3meter CNC bending machine, 4-axis back gauge, Fpedpfxoy Nd I Rj Ad Isi CNC crowning, TASC 6000, Willa hydraulic clamping, Tooling included, priced aprox. 10000€ Lower die 16mm - 3m - sectionized for 30° 50mm - 3m - sectionized 80mm - 515mm Upper Tool finer height 200mm, radius of 1mm, for 30° - 3m - sectionized, for thicker plates height 20mm, radius 3mm - 600mm - sectionized Feel free to contact.

Condition: good (used), functionality: fully functional, Used WILA OZU-318 tools V100mm Fpodsyzh Sdjpfx Ad Ioi OZU-318 100x80° R=20 H=100 1x 515mm 2x 200mm Total length L=915mm Fixed price € 1,650,- FCA Drachten, NL No response to offers or requests for lowest price.

Condition: excellent (used), functionality: fully functional, Set of used WILA OZU-317 tools V80mm OZU-317 80x80° R=16 H=100 6 x 515mm 1 x 200mm Fpsdpfx Ajyzh Irod Ioi Total length = 3290mm Fixed price €4,000,- FCA Drachten, NL Offers and requests for the lowest price will not be answered.

Year of construction: 2019, condition: new, We offer bending tools and punching tools for TRUMPF, AMADA, BYSTRONIC, LVD, SALVAGNINI, DURMA, ERMAKSAN, MVD, and HACO machines. Standard and custom tools. Fpsded H T Tfjpfx Ad Ioi Please send us your requirements, and we will provide you with the appropriate tool.