Used Paternoster for sale (194)

Condition: new, Year of construction: 2025, 1A Gmatick Storage Paternoster (roll rack) The foil storage Paternoster foils is suitable to use for the storage of all 3D-films, it is used as a high storage at the membrane press or as a space-saving storage solution for the 3D foils. With our Paternoster you can storage on very small area approximately 2, 4m x 1, 2m a lot of film rolls (up to 32 rolls of a Ø 300 mm). The required film is thus immediately available at the push of button. Our Paternoster are available from 2.8 m up to 6, 0 m as standard Paternoster. Also special solutions are offered by us, please contact us, we will then find the right solution for your storage. As additional equipment we offer center sleeves, a manual cutting station or the full automatic cutting device and we have also ionization solutions available at Gmatick. • Storage rods ø 42.4 mm • Sleeves inside Ø max. 82 mm,. • Load chain as a hollow pin chain with a breaking load of 100 kN, • Chain pitch is 50 mm hole to hole and this is the raster for the positioning of the mounting foil bars. • Control with a key switch (dead man) for on / off • Rotational speed of the chain is approx. 5.5 m / min Gbslhccqjff Huwsqop • Voltage 400 V, 3N; 50/60 Hz or as USA Version 480V 60Hz • Mains cable with CEKON plug 16A fuse protection (by the customer) 10A slow blow • ground load data at least 2, 2 kg / cm² • Side covering over the entire height of the Paternoster, guards from 2, 2 m above floor to top edge of the Paternoster. • Requirement for the installation of the Paternoster is a viable, flat and solid floor, • Floating floors you can’t install a Paternoster. It is forbidden

Condition: like new (used), Year of construction: 2022, operating hours: 500 h, Functionality: fully functional, Drying paternoster for finger-jointed boards Consisting of: - Transfer chain to finger-jointing press (foldable) - Drying paternoster (approx. 7 m, board length up to 6 m) - Cutting and zero-cutting saw Golhccowclkyeqqobp - Conveyor belt for waste wood disposal - Stacking machine - Strip magazine not for sale - Package cross conveyor The machine is in very good condition and has had very little use. The machine is still assembled but available immediately.

Condition: ready for operation (used), A Seybold bridge paternoster is available. Single load: 1700kp, max. storage product dimensions X/Y/Z: 760mm/800mm/6700mm, max. permissible total load: 8800kp. On-site inspection is possible. Gelhowwvwmoccqqobp

Condition: used, Year of construction: 2007, Machine no.: 500001292, 31 compartments, permitted GVW 70,000 kg, compartment dimensions approx. 800 x 1,200 mm, compartment load 332 kg, dimensions W/D/H 1,500 x 3,500 x 6,000 mm Gslhccjwuffzsqqsbp +++ Attention: This item is part of an online sale! +++

Condition: used, Year of construction: 1990, Functionality: fully functional, machine/vehicle number: 9494, total height: 7,000 mm, total width: 3,400 mm, load capacity per storage section: 200 kg, outer dimension width: 3,400 mm, construction height: 7,000 mm, construction width: 3,400 mm, type of input current: three-phase, input voltage: 380 V, input current: 16 A, frequency: 50 Hz, DGUV certified until: 10/2025, payload: 7,200 kg, nominal voltage: 380 V, total depth: 2,150 mm, Equipment: documentation/manual, safety light barrier, Megamat 132-342/36 RE Paternoster – Efficient Storage Lift System The Megamat 132-342/36 RE is a proven, space-saving paternoster storage system, ideal for the structured and efficient storage of small parts, tools, or documents. With its recirculation principle, it enables quick access to stored items and optimizes warehouse organization. Golhccqjv Ulbkeqjbp The system is ideal for industrial applications, workshops, or spare parts warehouses. Thanks to its robust construction and proven Megamat technology, this paternoster offers a reliable and durable solution for your storage needs. Note: This item is sold used. The sale is subject to exclusion of any warranty. Condition and functionality can be checked on-site. Disassembly and transport are the responsibility of the buyer.

Condition: reconditioned (used), Modernized machine with new LTG StoreControl P control system External dimensions: Height 5000 mm Width 2650 mm Gjlhcodnfdlocqqobp Depth 1250 mm plus 300 mm storage table 34 carriers with a payload of 140 kg each with clear usable dimensions: H = 220 mm W = 2220 mm D = 410 mm Chain pitch 254 mm Storage table at 1000 mm above floor level with wooden worktop Color: GRAY, surfaces cleaned, signs of wear may occur Motor power: 1 x 1.8 kW / 400 volts Subject to errors and technical changes Delivery and installation currently mainly in Germany, Austria, and several neighboring countries

Condition: good (used), In the field of 3D Thermoforming, we also offer presses, Turn over systems, film storage brushing machines, and membrane on machineseeker! Paternoster For the membran press membrane press FOILS-STORAGE-PATERNOSTER for the foil-roles stock and at the membrane press Technical Description: Height of the paternoster 3800mm Max. foil width 1600mm Max. foil diameter 500mm 12pcs bearing rods Size of the paternoster 1000x2370x3800mm Inclusive foil transporter (trolly) Drive capacity 1,5 kW Total upload 4080 kg at a max. rolls weight of 340 kg Tools weight incl. Up weight- 5240 kg Specific ground-load capacity (1,89 to/m²) Gbslhccqebgdv Ieqjp Pod-inside-diameter max. 90mm, bearing rods diameter 42,4 mm Side panels - total all over the overall height Protection lattice from 2,2 metres over the floor to the over edge overall-height Load chain as a hollow-bolt chain Fraction strength 100 kN, division 50mm = bearing rods-hanger system raster Rotation speed ca. 5,5 m/min Control with a key-switch with return (TOTMANN) for switch on/off Nominal voltage 400 V; 3N; 50 Hz mains (net) connection-pipe with CEKON-plug 16A Mains (net) fuse (construction sided)- 10A inert NO Price on request

Year of construction: 1996, Condition: good (used), For sale we offer a used Kardex/Paternoster. technical features: Length 3.400mm width incl. tray 1.960mm width without tray 1.650mm Height: 6.200mm Compartments: Length: 2.950mm Width: 620mm Height: 110mm Gbolhokuyk Ajccqqsp If you are interested, please contact us.

Condition: good (used), Functionality: fully functional, For sale unloaded from Norderstedt site due to closure of business Gjlhccqsrn R Rfoqsbp Kugler paternoster punch, suitable for Wire-O and register format 50 x 50 cm additionally 2 punching tools each EUR 1750

Condition: new, Year of construction: 2024, Customized paternoster stacking systems in different technical designs for sawn timber lengths from 3.0 - 6.0 m ( length on request ) options: - with/without lath bundling (different versions depending on requirements) - with/without slat magazine Gbjlsr Nx Tmjhccqqep single or double chamber depending on requirements with pneumatic gripper - Infeed and outfeed according to customer requirements

Condition: like new (used), Year of construction: 2014, Offered is one unit. Hänel Rotomat 980 Year of manufacture: 2014 Load capacity per carrier: 460 kg 20 shelves available, 10 per machine Carrier unit dimensions: W 2760 mm D 460 mm H 415 mm Gjlhor D S R Tsccqqsbp Device dimensions: W 3425 mm D 1770 mm H 8100 mm The devices have been serviced annually by trained specialists. The devices are in mint, barely used condition.

Condition: reconditioned (used), Modernized machine with new LTG-StoreControl P control system External dimensions: Height 6,010 mm Width 3,501 mm Depth 1,774 mm 25 carriers with a payload of 628 kg each In the clear usable dimensions: H = 359 mm W = 2,880 mm D = 628 mm Chain pitch 406 mm Storage table at 1,000 mm above floor level with worktop / plastic surface Light gray color, surface cleaned, signs of wear possible Motor power: 1 x 5.5 kW / 400 volts Gelhccqshfxkaoqobp Other extras: Automatic chain tensioning, Various intermediate shelves Subject to errors and technical changes Delivery and installation currently mainly in Germany, Austria, and several neighboring countries

Year of construction: 2012, Condition: good (used), Type: IND-PA Gbjlhcohyhlgocqqop Device no.: 0/1220744/1 Year: 2012 unit height: approx. 5600 mm unit width: approx. 2870 mm unit depth: approx. 4000 mm number of rolls: 45 Roll width: approx. 2370 mm shelf load: 200 kg Total load: 9000 kg Color: beige

Condition: good (used), Stacking boxes, stacking boxes, plastic boxes, Euro stacking boxes, transport baskets, stacking baskets, Euro stacking containers, Euro stacking containers, small load carriers, storage boxes, shelf boxes -6620x Storage bins: various sizes -771x storage bins Dimensions: 550/174/H110 mm -3483x Storage bins Dimensions: 175/135/H110 mm -2112x storage bins Dimensions: 275/175/H110 mm Gbjlhccedqc Hweqqep -30x storage boxes dimensions: 138/86/H110 mm -172x storage bins Dimensions: 174/136/H96 mm -56x storage boxes dimensions: 274/174/H96 mm -Sale: only complete

Condition: good (used), Year of construction: 1993, Bridge paternoster / carousel / long goods paternoster for long goods up to approx. 6.60m, 700kg / gondola - second-hand - : Price location: 32.500.-€ (net), plus dismantling etc.! Manufacturer: Schultheis (CH) Type: IPN 11/TL Fab. no.: 93-03018/2 Year of construction: 1993 Gbslhjq Tbmljccqqjp Payload per hanger: 700kg Total payload: 7,700kg Number of gondolas: 19 pcs. Connected load: 2x1.5kw, 3x380V Control voltage: 220v, 50 Hz One-sided pulling force: approx. 20% Device dimensions: L=6750mm, W=7750mm, H=4460mm Dimensions of the gondolas: L=550mm, W=6600mm, H=330mm The control system was renewed in 2001 and all documents are available. (Operating instructions and control instructions) TÜV and DGUV test reports are available. Load handling device, drive via roller chain with guide rollers for gondola transport Control: Main control point on the unloading side: electronic panel with dead man or automatic operation automatic operation Secondary control point at the rear: up, down, changeover switch Safety - one emergency stop switch at each of the four corners (to be acknowledged on the panel) Facilities: Two light barriers on each of the long sides (stop the system for the duration of the interruption) Defects: no inspection from 29.8.2023 Condition: good Available: immediately Location: 37445 Walkenried

Condition: ready for operation (used), Year of construction: 1975, Number of rollers: approx. 60, max. roller diameter: 280mm-300mm, machine dimensions X/Y/Z: approx. 5000mm/3000mm/2800mm. On-site inspection is possible. Golhccsugv Rhoqqobp

Condition: good (used), Year of construction: 2014, Manufacturer: Hänel Type: Lean Lift Year of manufacture 2014 Device dimensions: H 6302mm approx. W 2805 mm D 2810 mm Shelf 40 pieces up to 400kg per container H 57mm D 825mm W 2460mm Total load: 40,000kg (2×20,000kg) Gelhsvt Euzsccqqobp

Condition: good (used), Year of construction: 2003, Kardex carousel Type: SYS-120-1414 Gbslheq I R D Neccqqop Device no.: 03001086/001 Year of manufacture: 2003 Rack height: approx. 3110 mm Unit width: approx. 2950 mm Unit depth: approx. 1150 mm + 300 mm table top Number of shelves: 14 with 7 additional drawers Shelf width: approx. 2630 mm Shelf depth: approx. 320 mm Shelf height: approx. 330 mm Shelf load: 100 kg Total load: 1400 kg Color: white

Year of construction: 2003, Condition: good (used), Type: TLI 4500/2044 Gjlhccqjhyhlkoqobp Device no.: 03502 Year:2003 unit height: approx. 4500 mm unit width: approx. 2000 mm unit depth: approx. 7010 mm Number of rolls: 44 Roll width: approx. 1680 mm shelf load: 150 kg Total load: 7000 kg superstructure see photo 3000 mm Color: beige

Condition: good (used), Year of construction: 1990, Megamat carousel rack Type: 112-350-13 Gbelhccev Ewn Dsqqop Device number: 7479 Year of manufacture: 1990 Device height: approx. 2950 mm Device width: approx. 2675 mm Device depth: approx. 1130 mm + 280 mm table top Number of shelves: 13 Shelf width: approx. 2160 mm Shelf depth: approx. 295 mm Shelf height: approx. 330 mm Shelf load: 100 kg Total load: 1,300 kg Color: beige

Condition: good (used), Year of construction: 1987, Megamat carousel Type: 130-225-42 Device no.: 8048 Year: 1987 Rack height: approx. 5410 mm Unit width: approx. 2670 mm Unit depth: approx. 1300 mm + 300 mm table top Number of shelves: 42 Shelf width: approx. 2155 mm Shelf depth: approx. 410 mm Shelf height: approx. 200 mm Shelf load: 100 kg Total load: 4,200 kg Gbolovfl Swehccqqop Color: beige/green (device 3 on the photo)

Condition: good (used), total height: 8,600 mm, total width: 3,620 mm, Kardex Paternoster cabinet: 8.6 metres high - 3.62 metres wide and the cabinet has 48 drawers. Gjlhewgyileccqqebp

Condition: good (used), Year of construction: 1997, Long Goods Overhead Paternoster, Seybold, for long goods up to 6.60 m, 24 gondolas – used -: Gbslsv Iyqtjhccqqep Price ex-site: €29,500 (net), plus disassembly, etc. Manufacturer: Seybold & Co Type: IPS Industrial Overhead Paternoster 83997 Year of construction: 1997 Height: 7 m, Depth: 7.40 m Width: 7.55 m Maximum storage dimensions: Depth: 800 mm Height: 700 mm Length: 6600 mm Max. load per position: 1100 / 750 kg Hanging distance: 1500 = 800 x 700 and 750 = 400 x 300 mm Capacity: 24/8 positions Total load: 32,400 kg Manually operated push-button control with dead-man switch Forward/backward buttons 380 V, 24 A Condition: good Available: immediately Location: 97230 Estenfeld

Condition: new, Functionality: fully functional, Equipment: safety light barrier, Replacement controller for storage lifts and paternoster systems. With our "LTG StoreControl LL and StoreControl P" control systems, we are able to modernize paternosters and lifts that have a defective Cedes Safe C200 or Safe C400, for example, and keep them operational for many years to come. Our control systems fit storage systems of all manufacturers and types. The storage systems can remain fully loaded for the conversion. We can also provide special solutions as well as software connections. Gjloq Rcmtshccqqsbp

Condition: new, We supply and install our own, new, digital PLC controllers suitable for warehouse lifts and paternosters from all major manufacturers on the market. Our LTG StoreControl LL (warehouse lifts) and LTG StoreControl P-Touch (paternoster) controllers thus offer replacements for controllers for which spare parts are no longer available. Our controllers easily connect your dynamic storage systems to higher-level warehouse management systems and implement access restrictions. Gbslhceqlb Smecqqep