Used Eitec Gmbh for sale (68,928)

Condition: excellent (used), Year of construction: 2022, operating hours: 1,000 h, functionality: fully functional, machine/vehicle number: SN210551, overall weight: 14,000 kg, type of input current: AC, input voltage: 400 V, power: 400 kW (543.85 HP), Equipment: type plate available, A MIXACO heating/cooling mixer is a combined system consisting of a heating mixer and a downstream cooling mixer, specifically designed for the processing of powders, granules, and compounds (e.g., PVC dry blends, WPC, or masterbatches). Technical specifications – summary (details can be found in the documents): Hot mixer: • Volume: 3500 liters – Usable volume: 2500 liters • Tip speed: 5-50 m/s • Made of duplex steel – 1.4462 stainless steel • Power drive with 400 kW FC controlled • Vacuum up to 150 mbar abs. Cold mixer: • Volume: 9000 liters – Usable volume: 7650 liters • Tip speed: 3.5 – 7 m/s • Made of 1.4541 stainless steel • Power drive with 90 kW FC controlled The operating principle is divided into two physically and apparatus-wise separate process phases: 1. The heating mixer phase (heating and homogenizing) • Mechanical friction: In the heating mixer, a modular mixing tool rotates at a high circumferential speed (approx. 10–40 m/s). The intense flow and vortex formation (mixing vortex) causes the particles of the mixture to rub intensely against each other. • Heating: This mechanical friction generates the necessary thermal energy directly in the product, quickly and evenly heating the material to the desired target temperature (sometimes exceeding 100 °C). • Recipe component addition: At the same time, all recipe components, such as additives, dyes, or liquids, are perfectly homogeneously distributed. An integrated aspiration system also ensures the dehumidification of the mixture. 2. The transfer • Once the target temperature defined in the process program is reached, a contoured, dead-space-free outlet opens on the heating mixer. • The hot, homogeneous mixture is transferred with minimal residue and quickly to the cooling mixer, which is located directly below or next to it. The heating mixer is then immediately available for the next batch. 3. The cooling mixer phase (gentle cooling) • Heat exchange: In the cooling mixer (available in vertical or horizontal design), the hot material is passed over cooled surfaces. • Water cooling: A targeted cooling water circuit in the double jacket (bottom and side walls) efficiently removes thermal energy from the dry blend. Dedpfx Asz Iww Reilocn • Agglomeration prevention: A slow, material-friendly stirring mechanism keeps the mixture in motion until the final storage temperature is reached. This prevents caking (compaction) due to residual heat before the material is transferred to silos or further processing. Summary created with AI. The units can be inspected in operation in the Netherlands. The system for sale was used in the R&D center of UBQ for development purposes. This explains the very good condition for the low number of production hours. We also have a steel structure available for the setup. This is not included in the price. If there is interest, it can be negotiated separately. Currently, the system is located outside of Europe – we need to determine whether direct transport is feasible or whether import to Europe by UBQ is more sensible (which would allow for a sale within Europe with a reverse-charge mechanism).

Year of construction: 2017, condition: excellent (used), Pipe cutting system with optical laser marking detection The FZH Vario Flex is a fully automated pipe cutting system. It is specifically designed for the precise and reliable cutting of stainless steel pipes (e.g., for fuel, brake, air conditioning, or hydraulic lines). The system features optical laser marking detection. The control panel allows you to choose whether the cut is triggered mechanically (e.g., on the back of a union nut) or fully automatically via the optical detection of a laser marking applied to the pipe. Thanks to the integrated rotating 3-jaw cutting head and a micro-spraying unit (minimum quantity lubrication), the processing is extremely tool-friendly. The pipes remain almost completely dry and free of coarse contamination. The entire process, from loading to clamping, cutting, and unloading, is highly automated and carried out in a material-saving cycle. Fully integrated labeling & traceability system: The system is designed for modern quality standards (Industry 4.0 / Automotive). After the cutting process, the barcode label is automatically generated, assigned, and printed for complete part traceability (traceability & system logging directly integrated). Due to two separate box output stations (rear sluices with sliding doors), the system automatically switches to the second station when a box is full. The removal of the finished KLT boxes takes place in parallel with the main operating time without machine downtime. Advantages of the Vario cutting head series compared to conventional cutting methods Shortest changeover times in non-cutting separation Material-saving and free of contaminants Chip-free Easy to maintain No cooling and lubricating agents required Short processing times Cuts all common materials Can be combined with common pipe magazines or from a coil Special designs are possible Technical data & capacities Maximum pipe length (feed): 1,000 mm Material specification: Optimized for stainless steel pipes (also with pre-assembled union nuts or crimped ends) Sensors & positioning: Optical sensors for the automatic detection of laser markings on the workpiece Feed system: Automatic drum magazine / vertical disc feed (for manual or automatic loading) Length adjustment: Manually adjustable to different pipe lengths using a mechanical handwheel Cutting method: Chip-removing sawing / Rotating cutting head with three-jaw clamping and cutting mechanism (up to 600 rpm) Coolant system: Integrated micro-spraying unit (MMS) for minimum quantity lubrication Control: Siemens SIMATIC HMI industrial PC with TFT monitor, keyboard and mouse Setup operation: Mobile Siemens Teach-In terminal for manual axis configuration and position storage Integrated labeling and barcode printing system Enclosure: Aluminum profile system with safety polycarbonate windows Logistics / output Integrated box placement station 2 separate box output stations for rear removal via protected sluice systems with sliding doors Suitable for standardized KLT containers (600x400 mm and 400x300 mm) Manufacturer: FZH Engineering GmbH Type / Platform: Vario Flex Year of manufacture: 2017 Material: Stainless steel Dcedszw Ukcepfx Ailjn Cutting head: Vario flex Special features: Pipes with union nuts Diameter Ø 6-76 mm Output length L = 150-1,000 mm Separation based on laser marking Wall thicknesses: 1 to 1.3 mm Condition: The system is in excellent optical and mechanical condition.

Year of construction: 2022, condition: like new (used), functionality: fully functional, machine/vehicle number: WDW-70056, WDW – Calibrated containers – Continuous weighing scale for weighing wood pellets or other pellet-shaped bulk goods, complete with a discharge unit. Performance / throughput: 15.6 tons/hour; weighing accuracy: +/- 0.01 kg; cycle times: approximately 2 weighings per minute; the photo shows a representative image; the machine is delivered in its original packaging. Dodpfx Asz Ixc Ioilscn

Condition: used, Year of construction: 2000, machine/vehicle number: 000909 / 2000, functionality: fully functional, power: 15 kW (20.39 HP), volume flow: 10,500 m³/h, filter area: 61.5 m², overall weight: 1,950 kg, For sale is a complete, stationary AL-KO PROFI-JET BG 2 dust extraction and filtration system for wood dust, manufactured in 2000. The system was used in a wood processing production facility and is fully equipped with a fan, automatic filter cleaning, rotary valve airlock, silencer, frequency inverter, control cabinet/controller, and extensive ductwork. The dust extraction system was operated inside the production hall, and the cleaned return air was fed back into the production area. The filter system is labeled with H1 and, according to the label, is suitable for separating wood dust with a residual dust content of ≤ 0.2 mg/m³. Technical data of the filter system: Manufacturer: AL-KO THERM GmbH Type: PROFI-JET BG 2 Year of manufacture: 2000 Serial No.: 000909 Airflow rate: 10,500 m³/h Filter area: 62.5 m² Weight of the filter system: approx. 1,600 kg Filtration: surface filtration Filter cleaning: automatic compressed air cleaning Compressed air connection: max. 6.0 bar Filter elements: approx. Ø 120 mm × 2,500 mm length Height of filter unit: approx. 2,600 mm H1 wood dust rating: residual dust content ≤ 0.2 mg/m³ Dimensions: Length: approx. 2,400 mm Width: approx. 1,620 mm Overall height: approx. 4,500 mm Fan: Manufacturer: JKF Industri Type: JK-40 MTD L Power: 15 kW Speed: approx. 2,900 rpm Fan year of manufacture: 2000 The installed 15 kW drive motor is separately rated with 2,920 rpm at 50 Hz and protection class IP55. Frequency control and controller: The dust extraction system is equipped with a Danfoss VLT 6000 HVAC frequency inverter. Complete control cabinet with Siemens controller and Siemens TD 200 operating panel included. The automatic filter cleaning is carried out pneumatically via individually controlled valves. Rotary valve airlock: Manufacturer: AL-KO Dedoz Ikzpjpfx Ailjcn Type: ZRS 960 Rotary valve: Ø 320 mm Number of blades: 7 Inlet: 250 × 960 mm Outlet: 208 × 960 mm Capacity: 47,450 l/h Motor power: 0.55 kW Speed: 12 rpm Protection class: IP54 Additional equipment: The system includes: - Silencer, connection Ø 400 mm - Return air duct to the production hall - Complete system control - Danfoss frequency inverter - Automatic pneumatic filter cleaning - Rotary valve airlock - Extensive galvanized dust extraction and return air ductwork Large parts of the existing pipelines can be taken over after consultation. The system is still in its assembled condition. This allows the installation, duct routing and existing components to be inspected and documented before purchase. Location / Sale: Location: 3608 Thun, Switzerland Available: immediately Removal by: July 31, 2027 at the latest The system is sold in its current assembled condition. Dismantling, removal, loading and transport are entirely the responsibility of the buyer and at their own expense. If sold abroad, transport, export/import and customs duties will also be borne by the buyer. Inspection possible by appointment. Sale as is, without warranty. Selling price: 15,500.00 EUR Price net, any applicable taxes and duties. Export, customs clearance and import duties are the responsibility of the buyer.

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036721, clamping force: 6,500 kN, screw diameter: 70 mm, clearance between the columns: 1,110 mm, displacement volume: 1,078 cm³, injection pressure: 1,877 bar, injection weight: 981 g, opening stroke: 3,200 mm, plate height: 1,540 mm, drive type: Hydraulisch, clear span: 3,200 mm, tool weight: 2,200,000 g, Injection Moulding Machines Directly from the Manufacturer! As the manufacturer KraussMaffei, we offer you our certified and flexible stock machines: The hydromechanical two-platen clamping unit of the GXW machine sets new standards in terms of quality and productivity. With the sophisticated GuideX sliding shoe, forces are ideally absorbed and the service life of the moulds is extended. The innovative GearX locking system engages instantly and reliably. Powerful, user-friendly and value-retaining. TECHNICAL DATA: KM 650 / 2000 / 2000 GXW G06 (Order 38618339) CONTROL SYSTEM - MC 6 with 24'' TFT color screen with multitouch functions CLAMPING UNIT - Clamping force: 6500 kN - Max. mould opening force: 455 kN - Daylight opening (h x v): 1110 x 960 mm - Platen size (h x v): 1540 x 1440 mm - Mould installation height min. - max.: 1550 mm (without centre platen) - Opening stroke: 3200 mm - Max. mould opening distance: 1650 mm - Max. mould weight: 22,000 kg INJECTION UNIT 1 SP2000 - Screw diameter / type: 60 mm / thermoplastics - Effective L/D ratio: 23.3 - Injection pressure: 2420 bar - Shot volume: 792 cm³ - Shot weight at max. stroke for PS: 720 g - Injection speed: 140 mm/s - Injection throughput: 396 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 72.2 g/s - Nozzle contact force: 82 kN INJECTION UNIT 2 SP2000 - Screw diameter / type: 70 mm / thermoplastics - Effective L/D ratio: 20 - Injection pressure: 1877 bar - Shot volume: 1078 cm³ - Shot weight at max. stroke for PS: 981 g - Injection speed: 140 mm/s - Injection throughput: 539 cm³/s - Screw drive speed: 285 rpm - Plasticizing throughput: 98.3 g/s - Nozzle contact force: 82 kN Dcjdpfx Aow U N Ixsilsn ELECTRICAL PARAMETERS - Connected load: 341 kW - Power supply: 400 V / 50 Hz, 3 phases with neutral conductor WEIGHT & DIMENSIONS - Net weight: 43.5 t - L x W x H: 11.89 x 3.22 x 2.77 m ADDITIONAL EQUIPMENT - Wear-resistant plasticizing unit - BluePower full insulation for plasticizing cylinder - Open nozzle - BluePower ServoDrive - Pneumatic valve: 1-fold (BWAP), 1-fold (FWAP) - Pneumatic cascade valves: 6-fold (BWAP), 6-fold (FWAP) - Hydraulic core pull: 2-fold (BWAP), 2-fold (FWAP) - Mould heating: 96 zones (3.5 kW each) - Euromap interface for handling: E18 - Euromap central computer interfaces: E67, E77, E78, E63, E82.1 - Adaptive Process Control (APC+) - Graphic analysis package - Sliding table with turning unit, servo-driven - Vertical centre platen - Parallel clamping & opening during injection process with bar parallelism control between FWAP and centre platen or BWAP and centre platen - ColorForm interface signal interface for connecting an RPM unit - Electrical interface for HRS-Flexflow system - Electrical interface and hydraulic valves for "1-K dummy operation" - Interface for connecting a CoMo-Kistler Injection Basic System with good/bad part separation The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Condition: like new (used), Year of construction: 2016, operating hours: 500 h, functionality: fully functional, spindle speed (max.): 24,000 rpm, Gravograph IS 6000 IQ – CNC engraving machine – approx. 500 operating hours For sale is a very well-maintained Gravograph IS 6000 IQ with only approx. 500 operating hours. The machine is suitable for engraving and milling operations, for example, for the production of signs, lettering, and custom engravings. Machine data: Manufacturer: Gravograph / Gravotech Model: IS 6000 IQ Year of manufacture: 05/2016 Operating hours: approx. 500 Condition: used, very well maintained Equipment: Engraving software GS8-GRAPHIC incl. dongle Dedpfx Aez D Htgsilecn Sturdy machine table with T-slots for workpiece clamping Matching base frame Wired hand control unit Extraction system on the machining head Spraying device 750 W high-frequency spindle kit for the IQ series according to the order confirmation from November 2017 The machine was purchased in December 2016. Its excellent condition and low usage with only approx. 500 operating hours are particularly noteworthy. Price: net 12,500 EUR Location: 09627 Bobritzsch-Hilbersdorf Availability: immediately If you are interested, we look forward to receiving your inquiry.

Condition: used, Year of construction: 2016, Offered is a pad printing machine with protective enclosure. Equipped with plate holder, printing pads and remaining inks, where available. Operating usage: approx. 4000 cycles/year. Weight: approx. 400kg. Overall dimensions X/Y/Z: approx. 1300mm/1000mm/1790mm. Inspection possible by arrangement. Djdpfx Aijz Irl Nsljcn

Condition: new, Year of construction: 2023, functionality: fully functional, machine/vehicle number: 61036679, clamping force: 1,600 kN, screw diameter: 40 mm, displacement volume: 393 cm³, injection pressure: 1.892 bar, injection weight: 358 g, mold height (min.): 200 mm, ejector force: 33,000 N, ejector stroke: 100 mm, opening stroke: 950 mm, installation height: 500 mm, total length: 5,650 mm, total width: 1,820 mm, total height: 1,950 mm, overall weight: 9,700 kg, heating capacity: 15.5 kW (21.07 HP), drive type: Vollelektrisch, clear span: 570 mm, tool weight: 600,000 g, Injection moulding machines directly from the manufacturer! As the manufacturer KraussMaffei, we offer you our inspected and flexible stock machines: The base-level injection moulding machine, precisionMolding, provides the perfect entry-level solution for all-electric injection moulding, enabling you to respond to market demands quickly and innovatively. It combines high performance, simple operation, and short lead times. The machine is suitable for a wide range of applications, including the packaging, electrical and electronics, medical technology, and automotive industries. Your benefits: – Optimised price-performance ratio for a broad array of applications – High energy efficiency thanks to all-electric machine concept – Fast delivery times thanks to base machine concept with a wide range of available options TECHNICAL DATA: KM 160 / 750 PA G01 (Order 38670011) (Machine no.: 61036683, new, year of manufacture 2013) CONTROL SYSTEM • MC P1 with 15” TFT colour display featuring multi-touch functionality CLAMPING UNIT • Clamping force: 1,600 kN • Maximum mould opening force: 120 kN • Daylight (h x v): 570 x 520 mm • Platen size (h x v): 770 x 720 mm • Mould height min.–max.: 200 - 500 mm • Maximum opening distance: 950 mm • Maximum mould opening stroke: 450 mm • Ejector drive: electric • Ejector stroke: 100 mm • Ejector force forward/backward: 33 / 33 kN • Ejector speed forward/backward: 300 / 300 mm/s • Max. mould weight: 1,200 kg INJECTION UNIT • Screw diameter / type: 50 mm / standard • Effective L/D ratio: 20.2 • Injection pressure: 1,892 bar Dcsdpfxjyzz Iro Ailen • Shot volume: 393 cm³ • Shot weight at max. stroke for PS: 358 g • Injection speed: 200 mm/s • Injection flow rate: 393 cm³/s • Screw drive/speed: 267 rpm • Plasticizing rate (standard screw): 36.5 g/s • Nozzle contact force: 42 kN ELECTRICAL PARAMETERS • Connected load: 31.2 kW • Installed heating capacity: 15.5 kW • Power supply: 400 V / 50 Hz, 3-phase with neutral WEIGHT AND DIMENSIONS • Net weight with control cabinet: 9.7 t • Length x Width x Height: 5.65 x 1.82 x 1.95 m ADDITIONAL EQUIPMENT • Wear-resistant plasticizing • BluePower full insulation of plastification cylinder • Open nozzle • 1-fold air valve (BWAP) • Pneumatic control for hot runner shut-off 1-fold • Electrical interface for pneumatic cascade 4-fold • Euromap interface for handling E18 + E67 • Euromap interface (central computer) E67, E77 • 4-way water manifold • Electrical pre-equipment for hydraulic auxiliary unit • Automatic central lubrication system • Adaptive Process Control (APC) • Injection compression moulding function • Graphic analysis package • Swivelling device for injection unit The machine is located at our plant in Parsdorf and is available at short notice. Further additional options can be offered on request. We look forward to your enquiry.

Condition: like new (used), Year of construction: 2023, functionality: fully functional, machine/vehicle number: 052, turning length: 140 mm, turning diameter: 30 mm, spindle speed (max.): 6,000 rpm, spindle speed (min.): 200 rpm, spindle motor power: 9,000 W, rotational speed (min.): 200 rpm, rotational speed (max.): 6,000 rpm, total height: 1,800 mm, total length: 1,800 mm, total width: 1,200 mm, type of input current: AC, overall weight: 2,000 kg, Equipment: rotational speed infinitely variable, Transco Drehautomaten GmbH Type (Typ): tc10 Serial Number (Nr.): 052 Year of Manufacture (Baujahr): 2023 Machine Category: CNC Automatic Lathe (Second Operation / Audrema® series) Maximum Part Length: 140 mm (120 mm shank + 20 mm head) Dodpfxsz Ih Hcj Ailjcn Maximum Workpiece Diameter: 30 mm Production Rate: Up to 35 parts per minute Control System: Siemens CNC ControlMain Drive Power: Up to 9 kW Part Changing / Loading Times: Collet chucking (free drop): 1 s. Collet chucking (guided drop): 1.5 s. Three-jaw chucking: 2 s. Located in Israel l.

Condition: as good as new (ex-display), Year of construction: 2025, functionality: fully functional, machine/vehicle number: 24-042, overall weight: 200 kg, type of input current: AC, input voltage: 230 V, belt width: 400 mm, Magnet with neodymium head roller (can also separate slightly magnetized stainless steel parts), small conveyor belt (drum motor), and feed chute. The conveyor belt and feed chute are adjustable. Dcsdez Ihbgjpfx Ailen The machine is mobile on rollers, available immediately, and the price may be negotiable.

Condition: used, Year of construction: 2013, functionality: fully functional, machine/vehicle number: NS-009-0000-300, type of input current: AC, nominal power at 50% duty cycle: 250 kVA, throat depth: 300 mm, short-circuit current: 50,000 A, input voltage: 400 V, type of cooling: water, total width: 1,000 mm, total length: 1,000 mm, total height: 1,850 mm, overall weight: 1,000 kg, open-circuit voltage: 22 V, Zens Multifunction Resistance Welding Machine 250 kVA MF – 23 kN – 50 kA – Year of Manufacture 2013 For sale is a high-quality Zens multifunction resistance welding machine in a robust industrial design. The system was developed for demanding resistance welding processes and is ideally suited for series production in the automotive, supplier, electrical, and metal industries. The machine operates with modern medium frequency (MF) technology and achieves a welding power of 250 kVA at a 50% duty cycle. The powerful SER medium frequency inverter (700 A) enables a maximum welding current of 50 kA and ensures maximum process stability as well as reproducible welding results. With a maximum welding force of 23 kN and an overhang of 300 mm, the system is suitable for a wide range of resistance welding applications. Technical Data Manufacturer: Zens Machine Type: Multifunction Resistance Welding Machine Year of Manufacture: 2013 Welding Power: 250 kVA (Medium Frequency / MF) at 50% duty cycle Max. Welding Current: 50 kA SER Medium Frequency Inverter: 700 A Welding Control: SER-Mega1 Maximum Welding Force: 23 kN Overhang: 300 mm Equipment CE-compliant protective enclosure CE safety light curtain Welding table for welding forces up to 23 kN Pressure compensation tool Dcjdpfx Aiszqucfjlsn QSF-M quality assurance system Position measuring system for process monitoring PLC control (Siemens S7) Robust industrial design for continuous industrial operation The combination of powerful medium frequency technology, precise force and position control, and modern PLC and SER welding control ensures high process reliability and consistently reproducible welding results. Thanks to the complete CE safety equipment, the machine can be easily integrated into existing production lines. The system is in good condition and can be inspected and demonstrated at any time by prior appointment.

Year of construction: 2022, operating hours: 6,123 h, condition: used, functionality: fully functional, machine/vehicle number: 20-22-004, Like new, hardly used. Dodpfx Aisziaqfolecn

Condition: good (used), Year of construction: 2000, Weber Assembly Table / Joining Station Heavy-duty industrial assembly table / joining station from the quality manufacturer WEBER Konstruktion Maschinenbau GmbH. This machine is characterized by an extremely robust mechanical basic structure and is ideal for production facilities, workshops, or as a perfect foundation for a modernization project. Technical data (according to the nameplate): Manufacturer: WEBER Konstruktion Maschinenbau GmbH (Aschaffenburg) Type: Assembly table Dedpfx Aozni Rxeilecn Machine No.: BA 659 00 Year of manufacture: Electrical connection: 380 V (CEE plug available) Pneumatic connection: 6 bar "Everything from a single source: We will gladly offer you suitable financing for your project." You can find more items – new and used – in our shop! International shipping costs available upon request!

Condition: excellent (used), Year of construction: 2014, functionality: fully functional, machine/vehicle number: 13100019, type of input current: three-phase, overall weight: 1,000 kg, For sale: a professional log edging saw (optimizing saw) from the renowned German company Winter Holztechnik, model Optimax 100. The machine is fully functional, regularly serviced, and ready for immediate operation. It is ideally suited for the fast and precise removal of defects and the preparation of elements with fixed lengths in joinery workshops. Key features and advantages: PLC control: Intuitive touchscreen panel for easy programming. Multifunctionality: Capability for sequential cutting (memory for up to 10 dimensions) and cutting lines marked with fluorescent chalk. Efficiency: The machine can replace the work of several people, offering a speed of up to 80 cycles per minute. Precision: Very high cutting accuracy of +/- 1 mm. Technical data: Saw motor power: 7.5 kW. Feed motor power: 2.0 kW (feed speed continuously adjustable up to 80 m/min). Cutting height: max. 100 mm. Blade diameter: Ø 455 mm (bore 30 mm). Minimum material length: 300 mm. Dedpfx Aiozzw Uljlocn Power supply/Air: 400V / 8 bar.

Condition: refurbished (used), Year of construction: 2005, functionality: fully functional, machine/vehicle number: 106357-11, total length: 3,140 mm, total width: 1,800 mm, total height: 2,470 mm, overall weight: 3,500 kg, type of input current: AC, input voltage: 400 V, The machine was equipped with a new machine control system in 2024 and underwent a complete mechanical overhaul in 2025. The extensive overhaul involved the replacement of almost all essential components. As a result, the machine is in almost new condition technically. Dcedjz Irfvspfx Ailjn New control system in 2024: - SIMATIC S7-1500 PLC control system - SINAMICS S120 drive system Mechanical overhaul in 2025: - New tailstock housing, drill bush holder, and spindle housing - New workpiece support and tool support - 2x high-frequency spindles - 2x tool holders - 2x rotating collet chucks - Quill, including bearing - Ball screw drive, including bearing - Linear guides - Radial piston pump - Water cooler - 2x drilling oil supply - Flow divider - Pipelines and hoses replaced - Various filters replaced - Complete repainting Optional: - Chip conveyor can be retrofitted Oil mist extraction: - Connections are available Tool accessories: - Individual design possible according to customer requirements/customer workpiece. The deep hole drilling machine uses the single-lip drilling process. Information on the drilling unit: - Drilling diameter min/max: 1-12 mm based on ST 60 - Drilling depth: approx. 400 mm - Number of spindles: 2 - Spindle spacing: 120 mm - Spindle drive: 2 x 3.5 kW - Spindle speed, continuously variable: 1000 - 20000 1/min - Feed rate, continuously variable: 10 - 15000 mm/min - Rapid traverse: 15000 mm/min - Slide stroke (nominal): 800 mm - Center height (above table): 100 mm - Coolant supply: Deep hole drilling oil Machine frame: - Welded construction with integrated coolant tank - Top of the frame with continuous linear guide rails Spindle unit: - Motor spindles with frequency-controlled, continuously variable speed control. - Spindle head with connection for tool holder. Drill bush holder: - In cast design, fixed on the machine bed. - Holder for tool guidance system with Ø50 mm - Holder for sealing housing and immersion sleeves with bayonet lock Rotating tailstock: - With drive for rotating workpiece - Clamping quills with workpiece length compensation Inspection of the machine and further information are available on request.

Year of construction: 2013, operating hours: 7,700 h, condition: repair required (used), functionality: limited functionality, machine/vehicle number: 12090, This is a recycling extruder with side feeding for materials (flakes, pellets, etc.). The system is supplied with a control cabinet and a double vacuum system. The pelletizing system is missing at the end of the screw – it is not included in the scope of supply. The cylinder ends at the flange. The extruder is supplied without a screw. The frequency inverter for the main motor was replaced with a new unit 3 years ago. Installed power approx.: 474 kW Cooling water requirement approx.: 190 l/min Fresh water consumption approx.: 110 l/h Feeding system: • Diameter of the feeding screw: 200 mm • Drive for the feeding screw: 45 kW, frequency-controlled • Hopper capacity net 7 m³/250 ft³, • Gear motor 3 × 3 kW • 2 sight glasses in the hopper • 2 level indicators Extruder: • Diameter of the extruder screw: 145 mm • L/D ratio: 24 • Heating power: 50 kW • Extruder drive unit 280 kW Vacuum 1: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 11 kW • Vacuum capacity: 225 m³/h • Vacuum pressure: 33 mbar Vacuum 2: • Screw length: 16 L/D • Heating power: 40 kW • Vacuum pump power: 7.5 kW • Vacuum capacity: 190 m³/h • Vacuum pressure: 33 mbar Cylinder: • Cylinder: Bimetal extruder cylinder, • Reinforcement layer 1.8–2.0 mm thick, • Hardness 63–65 HRC Installation conditions: • Voltage: 3 × 400 Volts Dcedpfx Aisznz Ezjlon • Permissible fluctuation max.: +5 % – 5 % • Frequency: 50 Hz Permissible fluctuation max.: +4 % – 4 % • Protective measure: Multiple grounding • Ambient temperature: min. 15 °C, max. 35 °C • Humidity max.: 90 % • Altitude of the installation site: 0 – 1000 m The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center is being closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price is without packaging.

Condition: excellent (used), Year of construction: 2011, functionality: fully functional, machine/vehicle number: 2080092, Used CNC horizontal 5-axis twin-spindle double-table machining center Manufacturer: SW – Schwäbische Werkzeugmaschinen GmbH Type: BAW06-22 Year of manufacture: 2011 Machine No.: 2080092 Weight: approx. 16,000 kg Technical data: - CNC horizontal machining center - 5-axis design - Twin spindle - Double table Dcjdpez E Ddfsfx Ailjn - Travel ranges: - X-axis: 600 mm - Y-axis: 600 mm - Z-axis: 510 mm - Rapid traverse: up to 45 m/min - Tool interface: HSK-A63 - Spindle speed: up to 17,500 rpm Equipment: Machine with standard accessories. Availability: Available in the short term.

Year of construction: 2019, operating hours: 3,000 h, condition: excellent (used), functionality: fully functional, machine/vehicle number: 10031325, This is a high-resolution NIR system capable of detecting particles in the 3 mm size range. Additionally, the machine is equipped with an electromagnetic detector that has a sensitivity of approximately 1.5 to 1 mm, depending on the metal type. Depending on the settings, it can sort positively or negatively. Technical data: Belt width: 1024 mm Nozzle bar: 6.4 mm working width Upon request, complete documentation can be provided. Dcedezl Uzwepfx Ailjn The machine was in operation at an R&D center in Israel. Since the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 531 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. Dcodpjz Agv Ujfx Ailsn - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 532 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. Dcsdpjz Agw Eofx Ailen - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 533 MAP40, General Data: - Designed for wall-mounted toilets - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. Djdpfxoz Ag Rro Ailocn - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Year of construction: 2018, condition: used, functionality: fully functional, machine/vehicle number: Gießbank 530 MAP40, General Data: - Designed for wall-mounted toilets Dsdpfx Aiozz Rpcolocn - Low-pressure casting process with level control - Suitable for multi-part plaster molds - 40 mold stations per unit - A total of 160 mold stations - Mold spacing: 700 mm - Modular operation in units of 10 molds each - Operation with 10, 20, 30, or 40 molds in use per unit is possible - Different casting times per 10-mold section are possible Production Capacity - For currently manufactured "married" toilet models: the upper and lower parts are cast separately -> Two castings result in a complete toilet. 160 castings per casting cycle -> 80 complete toilets per casting cycle. - For models without "marriage": one mold station corresponds to one product -> up to 160 pieces per casting cycle. - Dimensions: Installation area approximately length: 33,800 mm, width: 4,100 mm, height: 4,300 mm. Single-row roller conveyor with a length of approximately 33,000 mm. Four lifting beam systems per unit. Each lifting beam is designed for 10 molds. One extraction trolley per unit. - Casting and slip system: Slip supply DN 100, slip return DN 100, compressed air connection 2 inches for the pressure line, filling via high-level or level tanks, two level tanks per unit, two casting lines per level tank, return of excess slip to the return slip tank, flushing of the slip lines with water and compressed air, four separate flushing systems per unit. - Mold mounting and clamping technology: Steel base frame, four lifting beams with electromechanical cable winch drive, cable breakage and cable slack protection, divisible vertical clamping devices, upper clamping beams with quick-release fasteners, pneumatic clamping hoses. - Demolding and handling: Pneumatic extraction assistance, molds can be clamped and tilted by 90 degrees, mold halves are manually separated, ergonomic transfer of the green part to a roller conveyor, two-hand safety control, quick-change system for different mold mountings, track for existing vacuum lifting system. - Compressed air and low-pressure system: Separate compressed air distribution for each 10 molds, three compressed air circuits (upper clamping beams and core boxes, vertical clamping devices, separation of the green part and mold), individual pressure control via pressure regulators, pressure monitoring of the clamping circuits, acoustic signal in case of insufficient clamping pressure, low-pressure system for stabilizing the green part in the mold and for hose drying after flushing. - Drying, ventilation, and lighting: Fans for drying the parts, diameter approximately 950 mm, LED lighting strips along the unit, active unit sections can be visually marked by the lighting, uniform drying of the plaster molds supports up to two casting cycles per day. - Electrical system and control: Two main switch cabinets, one main switch cabinet controls 20 molds and two lifting beams each, two-hand operation for safety-relevant movements, separate control cabinets on the level tanks and lifting beams. - Advantages: High production flexibility due to the 10-mold division, different products or casting times within one unit are possible, unused conversion components remain on the unit, suitable for different toilet models and production concepts, modular design facilitates partial occupancy and adjusted production quantities, extensive peripherals for casting, flushing, drying, demolding, and transport are available.

Condition: repair required (used), Year of construction: 2010, operating hours: 7,700 h, functionality: not functional, machine/vehicle number: 15158-10, working range: 4,000 mm, sheet thickness (max.): 12 mm, sheet thickness steel (max.): 12 mm, CNC plasma cutting system BACH ThermoCut 2000 with pipe cutting device, TEKA dust extraction system, and plasma source. Manufacturer: BACH Maschinenfabrik GmbH Type: ThermoCut 2000 Year of construction: 2010 For sale is a used CNC plasma cutting system BACH ThermoCut 2000, including pipe cutting device, plasma source, dust extraction system, and complete piping. The system was used in our machine manufacturing company until recently and is suitable for cutting sheet metal as well as processing pipes. Technical data: Working area: 4,000 x 2,000 mm Dcodpfx Aiozizkyolsn Plasma source: Thermal Dynamics Ultra-Cut 100 CNC control: myBach Pipe cutting device included Pipe diameter: min. 50 mm max. 320 mm Max. cutting thickness: Mild steel: up to 12 mm Stainless steel: up to 10 mm TEKA filter and dust extraction system included Complete dust extraction piping system included CE marking available Maintenance and condition The system was regularly maintained during its entire service life. Official maintenance by the manufacturer was last performed on August 20, 2013. After that, ongoing maintenance was carried out in-house. Filters of the TEKA dust extraction system were renewed approximately 6 months ago. Cutting torch head was renewed approximately 4 years ago. Cooling water filter is changed regularly, approximately once a year. The operating hour counter of the dust extraction system currently shows approximately 7,700 hours. Since the system was operated exclusively with the dust extraction system running, this value can be used as a good indication of the total operating time of the system. Known defect The system is currently not operational. After consultation with Voortman and Mr. Sobiech from Magma Industries, the cause is likely to be in the cooling circuit of the plasma source. According to the experts, the most likely causes of the fault are: Defective cooling water pump Defective flow sensor Leakage on the suction side of the cooling water system A final fault diagnosis has not yet been carried out. Spare parts for the installed Thermal-Dynamics plasma source are now only available to a limited extent. The machine is therefore explicitly sold as a system requiring repair or for refurbishment. Scope of delivery BACH ThermoCut 2000 CNC system Thermal Dynamics Ultra-Cut 100 plasma source Pipe cutting device TEKA filter and dust extraction system Control panel with controller Dust extraction piping Accessories according to existing equipment Special features ✅ Pipe cutting up to Ø 320 mm ✅ Complete package including dust extraction ✅ Solid industrial machine made in Germany ✅ Easy-to-disassemble gantry design ✅ Also interesting for buyers who already have a suitable plasma source Location 24161 Altenholz, Germany Price Negotiable €21,900 Inspection possible by appointment. Sale exclusively to commercial businesses, excluding any warranty for defects. Loading / Dismantling The system is offered exclusively for self-dismantling and self-collection. The buyer assumes full responsibility for the dismantling, loading, and removal of the machine at their own cost and risk. To assist with loading, a hall crane with a maximum lifting capacity of 10 tons is available on site. Use of the crane can be arranged in advance. Due to the size and weight of the system, we recommend an inspection before submitting an offer.

Year of construction: 2013, operating hours: 3,500 h, condition: used, functionality: fully functional, machine/vehicle number: 12400, TSM/tsi oscillating sieve machines are used for the classification, screening, and dust removal of bulk materials from almost all industrial sectors, such as stones and soils, chemicals, mining, pharmaceuticals, feed, and food. The machine for sale has a diameter of 1200 mm and is equipped with 3 sieve decks with mesh sizes of 3 mm, 1.4 mm, and 0.463 mm. In addition, spare sieves with the following dimensions are included: Dcjdszmzbmspfx Ailjn • 16 mm x 1 piece • 15 mm x 1 piece • 0.5 mm x 1 piece • 0.16 mm x 1 piece • 0.9 mm x 1 piece • 0.86 mm x 1 piece The drive has a power of 1.5 kW, 400 VAC, 50 Hz, 1450 RPM. The machine was in operation at an R&D center in Israel. As the company now operates a production facility in Europe, the R&D center will be closed. The machines will be transported to Europe at the owner's expense and can be delivered EXW at a port or at the production facility in Europe. The details for optimal transport need to be clarified. The machine price does not include packaging on a pallet.

Condition: excellent (used), Year of construction: 2009, The new, cold-regenerating adsorption dryer from Parker Zander combines proven and reliable elements of adsorption technology and impresses with a clear concept. Key features of the K-MT adsorption dryer series include: • Adsorber profiles manufactured in one piece • Separately controlled main and blow-down valves in a leak-proof design • Compact check valve combination, which guarantees continuous operational reliability while maintaining high availability. All adsorption dryers in the K-MT series feature: • Self-cleaning sieve beds on the wet side • High-quality desiccant During adsorption, the desiccant absorbs the moisture contained in the compressed air. Parker Zander uses only highly active desiccant of the molecular sieve type with high capacity. This desiccant guarantees a long service life, even at high inlet temperatures or low pressure dew points. Regeneration takes place in counterflow to the adsorption process. A portion of the dried compressed air is depressurized to atmospheric pressure and passed through the desiccant bed to be regenerated. Dcsdpfx Asypb Dueilon The moisture stored during adsorption is carried away with the partial flow of dry regeneration air. The regeneration air requirement of 14.3% for cold-regenerating adsorption dryers refers to: Operating pressure: 7 bar Inlet temperature: 35°C Pressure dew point: -40°C in a cycle with: - 5 minutes adsorption - 4 minutes desorption - 1 minute pressure build-up The Parker Zander 10-minute cycle, with 5 minutes of adsorption, includes 12 load changes per hour. The standard 6-minute cycle, with 3 minutes of adsorption, requires 20 load changes per hour and therefore inevitably results in 5.6% more regeneration. The Parker Zander 10-minute cycle saves energy costs while reducing wear and tear. Multitronic, the control system, with new, groundbreaking functions and a new design, is perfectly tailored to the cold-regenerating adsorption dryers of the K-MT series. It enables the highly effective adaptation of the adsorption dryer, even to extremely diverse operating conditions. From the permanently visually recognizable status to the pressure dew point control of the adsorption dryer, the benefits for the operator are clearly evident with multitronic. The multitronic system, housed in a clear and easily accessible control cabinet, offers: • A comfortable microprocessor control for all Parker Zander heatless dryer systems • Flexible adjustment of cycle times is possible. • LEDs on the front for the individual functions, such as: - Operation - Adsorption - Desorption • Selector switch I-0-2 for fixed cycles or variable cycles as a synchronous control with the compressor Possible options: • Direct pressure dew point measurement including a digital display • A potential-free output for the pressure dew point limit value • The ability to set the desired dew point in the range of -25°C to -40°C. Technical data: K-MT 8 Capacity m³/h: 72 Connection: G ½ Pressure bar: 16 Weight kg: 77 Electrical connection Watt: 50 Year of manufacture: 2009 Manufacturer's price: €8,880