Used Golmatic Md 23 for sale (20,560)

Condition: used, Number of spindles 6 St. Working width 230 mm Working height 120 mm Length of the planing table 2000 mm Feed motor 4 kW Feed speed 5-24 m/min. 1 WEINIG Unimat 23 E Planer and moulder ----- 6 spindles (with 2 rigth spindles, reinforced motors, 8,000 rpm, ATS control Machine will be cleaned and functionally checked before delivery Working width 20 - 230 mm Working height 8 - 120 mm 1st spindle (bottom) 5.5 kW (motor replaced) ----- Diameter 40 mm Speed ??6,000 rpm Tool swing diameter 125 - 180 mm Rebating unit including tool Hardened table insert in front of 1st (bottom) spindle 2nd spindle (right) 12.1 kW (motor replaced) ----- Shared motor with left vertical spindle Diameter 40 mm Speed ??8,000 rpm Tool swing diameter 112-250 mm Max. Tool diameter behind stop plane 203 mm Max. groove depth 35 mm Axially travel 80 mm 3. Spindle, left ----- Shared motor with 2nd spindle Diameter 40 mm Speed ??8,000 RPM Tool swing diameter 112-200 mm Max. groove depth 35 mm Axially travel 80 mm Pressure shoe in front of left spindle, including spring-loaded lateral roller pressure 4. Spindle, right 8.3 kW (motor replaced) ----- Diameter 40 mm Speed ??8,000 RPM Tool swing diameter 112-250 mm Max. tool diameter behind stop plane 203 mm Max. groove depth 35 mm Axially travel 80 mm 5. Spindle, top 7.5 kW ----- Diameter 40 mm Speed ??8,000 rpm Tool travel 112-200 mm Max. groove depth 35 mm Axially travel 45 mm Split pressure shoe in front of upper spindle, adjustable to the tool travel and pivoting away from the tool, spring-loaded. 6. Lower spindle 4.0 kW ----- Diameter 40 mm Speed ??6,000 rpm Tool travel 112-250 mm Codpexz Hh Ujfx Ab Tshf Max. groove depth 15 mm Axially travel 45 mm Spindles in general ----- All groove spindles with high concentricity. Lubrication points for the axial spindle movement. Feed system ----- Motor with mechanical brake, 4 kW Mechanical feed infinitely variable 5-24 m/min. Feed roller in front of the first lower tool pneumatically controlled up/down, Durofer pointed tooth rollers (Weinig patent) with depth limiter and self-cleaning Adjustment travel of the feed rollers relative to the left spindle, axial 35 mm Machine electrical system ----- Operating voltage 440 V (voltage range 380 - 420 V), 50 Hz. Machine frame, tables and stops ----- Infeed table 2.0 m long (incl. jointing guide) Manual Waxilit pump for table de-resin removal One driven rubber roller (spring-loaded in the outfeed table) Two driven rollers in the machine table, hardened Machine operation ----- Pressure shoe in front of the upper spindle with mechanical digital display. Extraction after the upper spindle with mechanical digital display. ATS/System, automatic 2-axis positioning for spindles 3 and 5 Minimum working height 12 mm Electric height adjustment of the upper spindles and the feed Central lubrication points on the front of the machine Electronic digital displays on spindles 3 and 5 (axial), spindle 6 (radial) and spindle 4 (axial and radial) Safety and noise reduction ----- Full safety enclosure Easily hinged safety hood with window. Covers the e...

Condition: used, Year of construction: 2022, operating hours: 18,400 h, functionality: fully functional, sheet thickness (max.): 3 mm, total length: 32,000 mm, total height: 5,000 mm, total width: 11,500 mm, Salvagnini production line – sheet thickness up to 3 mm. Combined line comprising storage tower, punching machine, turning and rotating unit, panel bending machine, unloading station (manual or automated), and press brake: MD1-3015.RCP.M9; S4_1931; ACN_0389; P4M_822; MB_1080_RBF; B3.170-3000. INCOTERMS: Ex-Works. Dismantling, packaging, removal, and collection to be carried out by the buyer. Location: Siemens AG, Carl-Benz-Straße 22, 60386 Frankfurt am Main. If interested or for further documentation, please feel free to contact us. Chjdpfox Da Nkjx Ab Tof

Condition: good (used), Year of construction: 2018, functionality: fully functional, travel distance X-axis: 560 mm, travel distance Y-axis: 360 mm, travel distance Z-axis: 480 mm, rapid traverse X-axis: 50 m/min, rapid traverse Y-axis: 50 m/min, rapid traverse Z-axis: 56 m/min, feed length X-axis: 560 mm, feed length Y-axis: 360 mm, feed length Z-axis: 480 mm, feed rate X-axis: 50 m/min, feed rate Y-axis: 50 m/min, feed rate Z-axis: 56 m/min, Make Hyundai Wia Model i-Cut 380 MD Year of manufacture 2018 Control system Siemens 828 chop-mill and 3D simulation Pallets 2 Palette size 650x400 mm Pallet load 250 kg Traverses X/Y/Z 560/360/480 mm Rapid feed X/Y/Z 50/50/56 m/min Spindle speed 24,000 rpm Spindle power 10.5/8 kW Tool taper BT 30 Big plus Number of tools in the magazine 20 pcs. Machine dimensions LxWxH 2.0x2.7x2.85 m Length: X-way 2.0 m Width incl. chip conveyor 4.1 m Machine weight 5200 kg Equipment: Chip conveyor with drum filter, swivel, pallet changer, Fixture plate with reference holes. Chsdpfow T Rv Iex Ab Tsf

Condition: used, functionality: fully functional, mileage: 453,870 km, power: 206 kW (280.08 HP), first registration: 11/2008, overall weight: 19,000 kg, fuel type: diesel, color: blue, axle configuration: 4x2, maximum load weight: 7,410 kg, empty load weight: 11,590 kg, tire size: 315/70 R22.5, next inspection (TÜV): 05/2026, fuel: diesel, wheelbase: 3,900 mm, brakes: retarder, driver cabin: day cab, gearing type: automatic, suspension: air, loading space volume: 13.3 m³, Year of construction: 2008, Equipment: ABS, additional headlights, air conditioning, airbag, central locking, compressor, differential lock, fog lights, hydraulics, immobilizer system, low noise, parking heater, truck registration, Model: SCANIA P280 DB 4X2 MLB JOAB Anaconda MD 13.3 cbm Air/Air Body: JOAB Anaconda MD Volume: 13.3 cubic meters Year of Manufacture: 11/2007 First Registration: 27.11.2008 Mileage: 453,870 km (original) Engine Power: 206 kW Hydraulic System (PTO) Auxiliary Heater Antennas Radio/Cassette/CD/MP3 Air Conditioning 2x Air-suspended seats with seat heating, fully adjustable Electric windows Electrically adjustable exterior mirrors Multifunction steering wheel Speed limiter Sun visor Work lights Fog lights High beam Warning beacon Tool/storage box Aluminum fuel tank Emission Class: EURO 5 Retarder/Intarder/Engine brake Overall Vehicle Dimensions (L x H x W): 805 cm x 318 cm x 255 cm Unladen weight: 11,590 kg Payload: 7,410 kg Gross permissible weight: 19,000 kg Differential lock Wheel configuration: 4x2 Wheelbase axle 1-2: 3,900 mm Tire size front axle: 315/70 R22.5 Tire size rear axle: 315/70 R22.5 Air suspension front/rear? Wheel covers Our vehicles are generally listed with valid inspection (TÜV) and emissions certificate (AU). These are usually foreign test certificates, which are sufficient for obtaining export license plates. For a valid TÜV and AU examination according to German standards, please contact us individually if required. We speak German and English, but feel free to send us a message in your language! Trade-in possible! Price is net! We can deliver your vehicle directly to the ports of Hamburg, Kiel, Bremerhaven/Cuxhaven, Lübeck in Germany, or Antwerp/Belgium and Amsterdam. We can ship the vehicle worldwide! Export license plates available on request! We support you with export procedures, original data confirmation for country homologation, supplier declaration, preparation of export documents, and customs plate provision if required. Vehicle inspection and test drive possible anytime, including weekends, by prior telephone arrangement! Chedpfx Abjx A Tnwo Tsf Disclaimer: The buyer is obliged to inform himself independently of the condition, dimensions, and features of the goods/vehicles. All information is provided without guarantee. Subject to change, prior sale, and errors.

Condition: used, mileage: 48,671 km, power: 174 kW (236.57 HP), first registration: 10/1992, overall weight: 12,500 kg, fuel type: diesel, color: blue, axle configuration: 2 axles, gearing type: mechanical, loading space width: 2,400 mm, loading space length: 3,800 mm, loading space height: 1,600 mm, total width: 2,500 mm, total height: 3,100 mm, Equipment: parking heater, A proper Iveco Magirus with 4x4 all-wheel drive and hydraulic Rotzler winch. Air-cooled V8 naturally aspirated diesel engine – extremely robust and powerful. 2x rear and center differential locks, rear extension for the winch, 5t towing capacity, 10t via rear extension with pulley. Tow bar with 12.0t ring eyelet and continuous braking system. 7 seats registered, various new parts, 10 Rx 22.5 tires. Freshly serviced with fuel filter replacement, air dryer cartridge replaced, starter batteries replaced, wheel brakes and all fluids lubricated and checked. Hydraulic clutch fluid and windshield wiper blades also replaced. We will deliver the Iveco with a fresh MOT/AU and H-certificate upon request. = +500€ Chodpfx Abjx A N Sfs Tef The GVW is 12.5t. The curb weight is approximately 8.0 t, so the 120-23 cannot be reduced to 7.5 t. The V8 diesel engine and 5-speed transmission run smoothly, the car is easy to drive. Top speed according to the documents = 93 km/h Bag dimensions: 3870 x 2490 x 1600 mm (LxWxH) +++ Errors, changes, and prior sale are reserved.

Condition: used, mileage: 732,501 km, power: 260 kW (353.50 HP), first registration: 11/2008, fuel type: diesel, number of seats: 40, gearing type: automatic, emission class: euro5, color: silver, brakes: retarder, Equipment: ABS, air conditioning, parking heater, +++20x available+++ +++Minor collision damage+++ +++Pick-up price excl. TÜV+++ Engine: Mercedes Benz Emission standard: EURO5 Total seats: 40 Seats: 31+8+1 raised/fixed Standing places: 101 Transmission: Automatic Safety: * Intarder * ABS * ASR * EBS * Fog lights Passenger compartment: * Parking heater * Wood floor effect * Air conditioning * Driver's microphone * Stroller space * Wheelchair ramp * Wheelchair space * Stop request button * Interior camera Exterior: Codpfx Abjwn Rw Ns Tohf * Matrix/destination display Hanover * Double-width door number: 4 * Lifting/lowering system * Power steering * Sun visor * Electric exterior mirrors * Roof hatches * Roof fans * Roof ventilator Other: * Twin tires * Vehicle length: 17.94 m * Vehicle width: 2.55 m * Vehicle height: 3.10 m * Tires: Front approx. 20% * Tires: Middle approx. 30% * Tires: Rear approx. 20% Our internal vehicle number: 11543 Errors expected. Images and text may differ from the vehicle. Always over 300 vehicles available.

Year of construction: 1990, operating hours: 4,569 h, condition: used, Auction item. Locomotive in working condition. On 2017 was made full overhaul. Moto hours counted after that. Sold as seen in pictures. Year of manufacture unknown Auction item. Csdox A Dtkopfx Ab Tjhf Šilumvežis darbinės būklės. 2017 metais buvo atliktas pilnas kapitalinis remontas. Moto valandos rodo dirbtą laiką po remonto. Parduodama kaip matoma nuotraukose. Gamybos metai nežinomi.

Condition: used, Year of construction: 1994, functionality: unexamined, planing height: 120 mm, planing width: 230 mm, total height: 1,700 mm, total length: 4,600 mm, overall weight: 3,550 kg, Machine with 6 planing heads bottom 4 kW, right 4 kW, left 4 kW, top 5.5 kW, top 4 kW, bottom 4 kW Codjv Dx Euspfx Ab Tohf Working width 25 - 230 mm Planing height 6 - 120 mm Feed speed 5 - 35 m/min Feed motor 4 kW Spindle speed 6000 rpm Spindle diameter 40 mm Infeed table length 2000 mm Machine weight 3800 kg Dimensions (L x W x H) approx. 4550 x 1700 x 1700 mm

Year of construction: 2007, condition: excellent (used), 1 x Record Packaging Machinery flow wrapper with Domino V230i thermal transfer overprinter and infeed conveyor. Fitted with an adjustable folding box, this unit is suitable for wrapping a variety of products in printed or clear film. Model - Scorpion MD SP. Date of manufacture - 2007. Cjdsukw Nbspfx Ab Tjhf Speed - between 20 to 120 packs/minute (depending on product size). Sealing jaws - 350mm long. Infeed conveyor - 185mm wide. Outfeed conveyor - 220mm wide. Previous use - for packing cereal bars and biscuits. Overall dimensions - 4670mm L x 1350mm W. *Please note* - Machine available in mid-October.

Condition: used, mileage: 540,000 km, Year of construction: 2001, Serial number: YV2J4DAC72A54xxxx Please contact ATS Norway for more information Please provide reference number upon request: 21881 Specifications: EU-approved until 06.06.2026 Mileage: 540,000 km Transmission: Manual Engine brake 6x2 Good tyres Full air suspension Rear support legs Platform length: approx. 6 m Palfinger PK 23002 (2006 model) Remote control Front and rear support legs Euro 3 Side boards included Sleeper bunk Radio/CD Climate control/AC Service done by owner Video available Ready for delivery Description:Volvo FM12 crane truck from 2001, equipped with a 23 t/m Palfinger crane from 2006.The truck is EU-approved and ready for delivery. Service and maintenance have been performed by the owner. Km: 540000 HK: 420 Technical approved: Yes EU-approved until: 06.06.2026 Own weight: 9540 Total Weight: 27000 Payload: 17385 Codpfx Ajxy Etaob Tehf Width: 255 Length: 960 Euro: 3 Model: FM12 6x2 Kranbil m/ 23 t/m Palfinger kran Gearbox: Manual

Condition: used, mileage: 63,521 km, power: 174 kW (236.57 HP), first registration: 02/1992, overall weight: 12,500 kg, color: blue, axle configuration: 2 axles, gearing type: mechanical, loading space width: 2,400 mm, loading space length: 3,800 mm, loading space height: 1,600 mm, total width: 2,500 mm, total height: 3,100 mm, Equipment: parking heater, A proper Iveco Magirus with 4x4 all-wheel drive and hydraulic Rotzler winch. Air-cooled V8 naturally aspirated diesel engine – extremely robust and powerful. 2x rear and center differential locks, rear extension for the winch, 5t pulling capacity, 10t via rear extension with pulley. Tow bar with 12.0t ring eyelet and continuous braking system. 7 seats registered, various new parts, 10x22.5 tires. Freshly serviced with fuel filter replacement, air dryer cartridge replaced, starter batteries replaced, wheel brakes and all fluids lubricated and checked. Hydraulic clutch fluid and windshield wiper blades also replaced. The front inner fenders were professionally welded by us, and the outer chassis parts and rims were repainted. The Iveco will be delivered by us with a fresh MOT/AU and, upon request, with a new MOT/AU. H-approval submitted, = +500€ The GVW is 12.5t, the curb weight is approximately 8.0t – the 120-23 cannot therefore be reduced to 7.5t. Cjdpfjx A N R Usx Ab Tshf The V8 diesel engine and the 5-speed transmission run well, the car can be driven without any problems. Top speed according to the documents = 93 km/h Body dimensions: 3870 x 2490 x 1600 mm (LxWxH) +++ Errors, changes, and prior sale are reserved.

Condition: used, mileage: 708,997 km, power: 260 kW (353.50 HP), first registration: 12/2008, fuel type: diesel, number of seats: 40, gearing type: automatic, emission class: euro5, color: silver, brakes: retarder, Equipment: ABS, air conditioning, parking heater, +++20x available+++ +++collision damage+++ +++pick-up price without TÜV+++ Engine: Mercedes-Benz Emission class: Euro 5 Transmission: Automatic Seats: 31+8+1 high/fixed Standing places: 101 _____ Safety * Retarder * ABS, ASR, EBS * Fog lights Passenger compartment * Auxiliary heating * Wood floor look * Air conditioning * Driver's microphone * Stroller area * Wheelchair ramp * Wheelchair space * Stop request * Interior camera Exterior * Fixed trailer coupling * Matrix: Hanover * 4x double-wide doors * Lift / lowering system * Power steering * Sun visor * Exterior mirrors electric * Roof hatches, fans, roof ventilators Miscellaneous * Twin tires * Tires: FA 20%, MA 20%, RA 20% Chodjv Uurfepfx Ab Tof * Vehicle dimensions: 17.94m length, 2.55m width, 3.10m height Our internal vehicle number: 11453 Errors excepted. Pictures and text may differ from the vehicle. Continuously over 300 more vehicles on offer.

Condition: used, mileage: 112,348 km, power: 232 kW (315.43 HP), first registration: 08/2019, overall weight: 26,000 kg, fuel type: diesel, axle configuration: 3 axles, next inspection (TÜV): 08/2026, gearing type: semi-automatic, emission class: euro6, Equipment: ABS, air conditioning, electronic stability program (ESP), navigation system, 1344Bh 4/25 Left-hand drive, differential lock, steered/liftable trailing axle, stop brake for waste collection vehicle, 3-seater, ASR, ADR, central locking, speed limiter 30/85 km/h, radio, rotating beacons, pop-up roof, decorative inlays, armrests, sun blind, cornering light, daytime running light, LED position lights, emergency brake signal (ESS), Brake Assist 2, Lane Guard System 4, HS turning assistant, Olympus Industrial 23 m³ with HS dumping hopper Comfortlift type U-K-KL EuroMax, suitable for 80 l to 5 m³, bulky waste collection with foldable chute, comfort gearshift, central lubrication system, hopper lifts approx. 2 t, Welvaarts scales Chjdpswcikqjfx Ab Tef

Year of construction: 2020, condition: ready for operation (used), Main Drive Number of axis 3 Spindle Speed 18000 RPM Spindle motor power 5.6 kW Movement X-Axis Movement 3350 mm Z-Axis Movement 180 mm Y-Axis Movement 200 mm Chedpfx Aexy Anhjb Tjf This 3-axis COMEC MD TOP XL CNC Wood Machining Centre was manufactured in 2020. It features a robust mono-block structure, high-speed axes positioning up to 70 m/min, and versatile electro-spindles for drilling, milling, and cutting. The machine includes a CAD-CAM control unit with a 17" touchscreen and full safety enclosures. If you are looking to get high-quality woodworking capabilities, consider the COMEC MD TOP XL machine we have for sale. Contact us for more information. Application Types CNC Wood Machining

Condition: refurbished (used), Contact us for the most up-to-date options and find the scale that perfectly fits your production process. Cedox Ahauspfx Ab Tshf We supply top brands such as Yamato, Ishida, Rovema, Prins, and Wipotec, for weighing a single product, multiple products simultaneously, or larger and free-flowing products using linear scales. All of our scales can be tested, serviced, or fully refurbished. A modernized scale often delivers the same performance as a new one but is usually a more cost-effective solution, including a warranty. Our specialists are also available for technical questions and support with installation, commissioning, or adjustment.

Condition: good (used), Tool holder, milling holder, collet holder, collet chuck, chuck, milling tool, adapter, clamping unit, tool holder, collet sleeves -Milling holders: SK30 23 pieces -Type: various versions, see photos Chodjtxkuhopfx Ab Tef -Price/Delivery: complete -Transport dimensions: 480/400/H315 mm -Total weight: 20.2 kg

Condition: excellent (used), Four-side planer SCM Compact 23 Working width: 230 mm Working height: 120 mm Number of spindles: 4 Spindle arrangement: Bottom Right Left Top Spindle speed: 6000 rpm Two feed speeds: 6–12 m/min Codpfx Ajxyv A Eob Tohf Adjustable spindles

Condition: used, mileage: 724,152 km, power: 260 kW (353.50 HP), first registration: 12/2008, fuel type: diesel, number of seats: 40, gearing type: automatic, emission class: euro5, color: silver, brakes: retarder, Equipment: ABS, air conditioning, parking heater, +++20x available+++ +++Minor collision damage+++ +++Pick-up price excl. TÜV+++ Engine: Mercedes Benz Emission standard: EURO5 Total seats: 40 Seats: 31+8+1 raised/fixed Standing places: 101 Transmission: Automatic Safety: * Intarder * ABS * ASR * EBS * Fog lights Passenger compartment: * Parking heater * Wood floor effect * Air conditioning * Driver's microphone * Stroller space * Wheelchair ramp * Wheelchair space * Stop request button * Interior camera Exterior: * Matrix/destination display Hanover * Double-width door number: 4 * Lifting/lowering system * Power steering * Sun visor * Electric exterior mirrors * Roof hatches * Roof fans * Roof ventilator Other: * Twin tires * Vehicle length: 17.94 m * Vehicle width: 2.55 m * Vehicle height: 3.10 m * Tires: Front approx. 20% * Tires: Middle approx. 30% * Tires: Rear approx. 20% Cedpfx Abjwn Rxas Tohf Our internal vehicle number: 11544 Errors expected. Images and text may differ from the vehicle. Always over 300 vehicles available.

Condition: used, Year of construction: 2006, Four-sided planer Little Kuper SWT 23 XL-6 Year of construction 2006 Chjdexyvzuopfx Ab Tjf min/max Working height 8/125 mm min/max Working width18/230 mm Working speed 6/28 m/min Spindle speed 6000 rpm Spindle diameter 40mm engines 1st. Spindle - under 5.5 kW 2nd Spindle - right 5,5kW 3rd Spindle - left 7.5kW 4th. Spindle - above 11kW 5th. Spindle - above 7.5kW 6th Spindle - under 7.5kW Main fuse 105 amp. Dimensions 7500 x 2000 x 1850 mm (L x W x H), weight 4000 kg - Year: 2006 - Documentation available: No - CE certificate present: No Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Yorick Diebels

Condition: good (used), Year of construction: 2015, functionality: fully functional, turning length: 650 mm, turning diameter: 400 mm, Fanuc Oi-TD control 3-jaw chuck diameter 250mm 12-fold revolver tail stock chip conveyor The machine has only 4051 switch-on hours Technische Daten: / technical details Schwingdurchmesser / rotary diameter 650 mm Drehdurchmesser / turning diameter 400 mm Drehlänge / turning length 650 mm X-Weg / X-travel 230 mm Csdpfxsvi Haqj Ab Tshf Z-Weg / Z-travel 650 mm max. Drehzahl / max. spindle speed 4500 UpM /rpm Anzahl der Revolverplätze / number of tool places 12 Antriebsleistung Spindel / drive capacity spindle 11/15 kW Gewicht ca. / weight ca. 5400 kg Technische Daten, Zubehör und Beschreibung der Maschine sind unverbindlich - Technical data, accessories and description of the machine are not binding.

Condition: used, turning diameter over bed 260 mm turning diameter over slide rest 140 mm turning length 500 mm centre height 125 mm bed width 160 mm spindle turning speed range 16: 110-3600 U/min spindle bore 28 mm face slide travel 120 mm upper slide-adjustment 120 mm tailstock quill taper MT 2 tailstock quill adjustment 80 mm drive motor 0,37 / 0,88 kW weight of the machine ca. 350 kg Chsdpfsvtthijx Ab Tof dimensions of the machine ca. 1,3 x 0,6 x 1,2 m Mechanic's lathe with manual feed and spindle support, drive via V-belt and stepped pulleys as well as 2-pole motor, hardened, finely ground work spindle, support adjustment over the entire bed length using eccentric clamping lever, three-jaw chuck, collet device with pliers, crank tailstock, cast base. Machine dealer with own stock of 1600 m².

Condition: good (used), Year of construction: 1998, functionality: fully functional, Four-side planer Weinig Hydromat 23, finger jointing machine 8 spindles, Chjdjxqh E Hspfx Ab Tof Working width: 230 mm, Working height: 160 mm, Spindle diameter: 50 mm, Feed: 7.5 kW / 6–36 m/min, Spindle arrangement: 1-Bottom (7.5 kW) 2-Right (7.5 kW) 3-Left (7.5 kW) with profile jointer 4-Right (7.5 kW) with profile jointer 5-Top (7.5 kW) with hydraulic clamping 6-Bottom (30 kW) with hydraulic clamping 7-Top (7.5 kW) with hydraulic clamping and straight jointer 8-Bottom (7.5 kW) with hydraulic clamping and straight jointer. Hard coating. Two powered rollers in the table.

Year of construction: 2000, condition: ready for operation (used), Technical Specification Max. Cutting Length 3300 mm Cjdpfx Abjxyl Spe Tshf This HOLZMA HPL 23/X/33/22/30/L was manufactured in 2000. A robust used panel saw featuring a cutting length of 3300 mm, 3 air cushion tables, and a lifting table measuring 3300 x 2200 mm. It includes a main saw with 18 kW power and a scoring saw of 2.2 kW, controlled by a CADMATIC system. Contact us for more information about this machine. Application Types Sawing (Wood)

Condition: used, mileage: 695,791 km, power: 260 kW (353.50 HP), first registration: 11/2008, fuel type: diesel, number of seats: 40, gearing type: automatic, emission class: euro5, color: silver, brakes: retarder, Equipment: ABS, air conditioning, parking heater, +++20x available+++ +++Minor collision damage+++ Engine: Mercedes Benz Emission standard: EURO5 Total seats: 40 Seats: 31+8+1 high/fixed Standing places: 101 Codpjwru I Hofx Ab Tjhf Transmission: Automatic Safety: * Intarder * ABS * ASR * EBS * Fog lights Passenger compartment: * Parking heater * Wooden floor look * Air conditioning * Driver's microphone * Stroller parking space * Wheelchair ramp * Wheelchair space * Stop request button * Interior camera Exterior: * Matrix/destination display Hanover * Double-width doors number: 4 * Lifting/lowering system * Power steering * Sun visor * Electrically adjustable exterior mirrors * Roof hatches * Roof fans * Roof ventilator Other: * Twin tires * Vehicle length: 17.94 m * Vehicle width: 2.55 m * Vehicle height: 3.10 m * Tyres: FA approx. 30% * Tyres: MA approx. 20% * Tyres: RA approx. 20% Our internal vehicle number: 11589 Errors excepted. Pictures and text may differ from the vehicle. Over 300 vehicles permanently on offer.

Condition: as good as new (ex-display), Year of construction: 2025, ST 3 classic F 23 - Combined sawing-routing machine With tiltable saw blade, tiltable milling spindle and format sliding carriage made of anodized aluminum Sturdy cast steel construction Large support surface and precise cast iron table High-precision format sliding carriage made of anodized aluminum (travel 2250 mm) Large extension arm (900 x 600 mm) with telescopic aluminum stop Max. Saw blade Ø 315 mm with scoring device, swiveling from 90°-45°. Chsdpocnwydefx Ab Tef Saw parallel fence with fine adjustment Stable sawing unit and large dimensioned double cradle frame unit guarantee highest stability, precision, smooth running and long service life Solid and precise machine table made of stress-free cast iron 3 milling speeds, manually adjustable from 3.500 - 10.000 min-1 With right-left rotation of the milling spindle Standard arc milling protection hood Two 5.0 kW motors with high power reserves Cast iron milling unit top mounted on both sides precision ball bearings on top close to the lever point four optimally graduated milling speeds, enabling the grinding of workpieces Powerful motors Industrial motor, 100% duty cycle suitable for continuous use (full load) Scope of delivery: Curved fraise protection hood anodized aluminum format sliding carriage aluminum stop jaws folding stop jaws Technical data Dimensions cast iron worktable 1112 x 430 mm working length 2250 mm max. saw blade Ø with/without scoring 315 mm max. cutting height at 90°/45° 100/70 mm max. cutting width 2660 mm saw blade tilting 90° - 45° cutting width 900 mm speed 4000 1/min. table cutter - spindle tilting 90° - 45 useful length of spindle 100 mm max. tool Ø 210 mm max. tenon tool Ø 275 mm max. tool-Ø retractable 180 mm speeds 3.500/7.000/10.000 1/min. General - motor power 400 V/50 Hz/S6 40% 2 x 5,0 kW ( 6,6 PS) Weight 470 kg Suction nozzle-Ø 2 x 120 mm Suction nozzle-Ø saw blade guard 60 mm Location: Ex stock 54634 Bitburg - immediately available -