Used Folding Low Pressure Press for sale (32,407)

Condition: used, Marvel Townsend StorkDMM50 meat bone separator to produce best quality low pressure deboned meat when used in conjunction with a Baader or SEPAmatic. This machine has come direct from a closed meat factory in Scotland. Almost impossible to find these machines on the used market. Bwodpfx Agslkc I Rjgep

Condition: excellent (used), Year of construction: 2001, functionality: fully functional, pressure: 1 bar, 1 used low-pressure steam boiler ----- Manufacturer: VIESSMANN Model: Vitoplex 100-LS Output: 580 kW Steam output approx.: 800 kg/h Water content approx.: 1,316 l Permissible operating overpressure: 1 bar Year of manufacture: 2001 CE marking: 0035 Bsdpfx Agow I T E Iogowp Equipped with Weishaupt gas burner, separate control cabinet, feed water pump, and the existing coarse and fine fittings.

Year of construction: 2003, condition: used, Additional title: brew vessel from stainless steel Total volume: 260 hl Diameter approx.: 3 m Diameter incl. insulation approx.: 3 m Frame height: approx.: 2 m Bwjdpfx Agovcqz Eegsp Width: 3,4 m Material: stainless steel 1.4301 Base construction: on stainless steel pipe supports, ground pegged Features: external boiler, conical hood stainless steel, D = 3200 mm), conical insulating hood (stainless steel outside diameter = 3400 mm), 2 outlets DN200 und DN100, manhole DN600, outlet vent (12000 mm), interior lighting

Condition: used, Year of construction: 1998, Manufacturer: PCM Delasco Bjdpfx Agjx R Dzmjgowp Model: JZ237 Type: Low-pressure peristaltic pump / Slurry pump Year: 1998 Maximum pressure: 1.5 bar Maximum flow rate: 300 to 600 liters/hour

Condition: used, Year of construction: 2011, Manufacturer: PCM Delasco Model: 2Z3 Type: Low-pressure peristaltic pump / Paste pump Year: 2011 Density: 1.8 max Cycle: 165 cm Max speed: 56 rpm Max pressure: 1.5 bar Bwodpfx Ajx R Dzgeggjp Max flow rate: Approx. 9 liters max (calculated estimate) Self-priming Max viscosity: 15,000 cP

Condition: excellent (used), Year of construction: 2017, functionality: fully functional, machine/vehicle number: MClL-800?OSK+KK, input voltage: 400 V, type of input current: three-phase, type of cooling: air, total width: 2,330 mm, total length: 2,150 mm, total height: 2,800 mm, sheet thickness aluminum (max.): 2 mm, continuous operating pressure: 0.5 bar, table length: 1,150 mm, Equipment: hot water, type plate available, Industrial rotary spray washer with fume extractor and ion exchange station. Designed for washing steel, aluminum, non-ferrous metal elements with a maximum load of 250 kg and dimensions of 1000x800 mm. Technical documentation and completed swewis are available for the station. More information at the phone number. Bsdpfjwnbh Ejx Aggowp

Year of construction: 2013, condition: as good as new (ex-display), functionality: fully functional, machine/vehicle number: 20910-01, Unused Hosokawa Bepex model BX 150 stainless steel (AISI 316) basket extruder for low pressure extrusion. Products with loose structure, large surface and good forming properties are produced with this machine. The product consists of a paste of low flow characteristics and low moisture content. The product to be processed is transported by the inlet into the machine. In the product area are two rotors which works in oposite directions to each other. - The upper 2-arm rotor with angle rotor and additional stirrers mixes and conveys the material down. Rotor is driven through gearbox by 0.55 kW, 60 Hz electrical motor, adjustable speed from approx. 14 - 139 rpm. - The lower 3-arms rotor is equipped with curved arms and rotor knives. Through the lower 3-arm rotor the product is compressed and forced through a cylindrical screen basket. The diameter of the granules results from the perforation diameter in the screen basket. Rotor is driven through gearbox by 3.0 kW, 60 Hz electrical motor, adjustable speed from approx. 15 - 144 rpm. Bwjdpfx Ast Tvx Tjggop Includes (2) extrusion screens 2 mm dia x 1.2 mm thick, switchboard with integrated control panel. Mounted on stainless steel frame with (4) wheels.

Condition: new, These Items are unused and boxed in original Packaging. Supplier Catalogue No. 52002567 The Mettler Toledo InPro 3253/120/PT1000 is a high‑performance in‑line pH sensor / electrode with some specific featuresA pre‑pressurized, liquid‑filled, low‑maintenance pH sensor. It has a built‑in PT1000 temperature sensor for temperature compensation. The sensor length (shaft) is 120 mm, which is relatively short, making it suitable for installations with limited insertion depth. It is sterilizable/autoclavable and optimized for steam sterilization or autoclaving cycles. That means it can withstand repeated sterilization without losing performance. Reference system: pre‑pressurized liquid electrolyte, with a ceramic diaphragm, and includes an Argenthal cartridge with a silver‑ion trap (for better performance in environments with sulfides etc.) Bwedpfx Aexv Dv Eoggjp It can handle pressures up to 4 bar gauge and works in the range 0 °C to 100 °C. It has process connection thread of Pg 13.5, and its connector is of “VP” type This sensor would be used in settings where real‑time, reliable pH measurement is needed under harsh or demanding conditions. Some examples: - Biopharmaceutical / biotechnology production, e.g. fermenters, bioreactors, where sterilisation (e.g. steam) is frequent and you need accurate pH control. - Hygienic food or beverage processing where cleaning and sanitisation/sterilisation are done in‑place (CIP / SIP). - Chemical processing, especially where pH may swing extreme and environment may be harsh (high/low pH, temperature, maybe some contaminants). - Water/wastewater treatment in situations needing durable, robust probe

Condition: excellent (used), Kontron 325 Tenary Low-Pressure Gradient Pump HPLC up to 10 mL - Pump system for tenary low-pressure gradients - All low-pressure gradient devices integrated into one solution system - 10 programs with customized instructions - Column shock protection extends shelf life - Intelligent compressibility compensation - Stackable with other/additional HPLC modules - Full control of the AUtosampler 360 via the keypad with a display Type: Double series-piston wetted Materials: SS 316, PTFE, KEL-F, ceramic, ruby, and sapphire Flow rate: 0.05 to 10 mL per minute Flow rate precision: 0.3% RSD (at 1.5 mL/min) Flow rate accuracy: 2% (at 1.5 mL/min) Flow linearity: r2 > 0.998 Pressure: 40 MPa or 7500 psi (flow-dependent) Pressure sensor: Piezoelectric sensor Display: 2x40-character LCD External control: RS-232C Bwsdpfxjlkbpts Aggjp Inputs: Injection synchronization, flow stop Outputs: Pressure and drive alarm, pressure signal, relay injection, relay step, RS-232 (for Autosample 360) Power supply: 110/220 V +-10%, 50/60 Hz, 120 VA Dimensions: 40 cm wide, 54 cm deep, and 17 cm high Find more items - new and used - in our shop! International shipping costs upon request!

Condition: used, Year of construction: 2008, machine/vehicle number: 32063, functionality: fully functional, operating hours: 28,800 h, power: 42 kW (57.10 HP), input voltage: 400 V, input frequency: 50 Hz, type of input current: three-phase, pressing force: 320 t, stroke length: 250 mm, table length: 6,100 mm, total length: 8,000 mm, total width: 3,200 mm, total height: 3,800 mm, overall weight: 35,500 kg, Equipment: CE marking, documentation/manual, safety light barrier, For sale is a powerful and reliable CNC press brake, type LVD PPEB 320/61, ideal for precise bending operations in sheet metal processing. Manufacturer: LVD Model: PPEB 320/61 Control: CNC Design: Robust, industrial design Suitable for: Heavy-duty and large-format bending operations Technical data: CNC-controlled back gauges Hydraulic upper and lower tool clamping system Safety equipment in accordance with industrial standards 5 axes Press force: 320 t Bending length: 6,100 mm Frame width: approx. 5,050 mm Stroke: approx. 250 mm Installation height (table–ram): approx. 500 – 570 mm Condition: The machine is in used, operational condition. Regular maintenance has been performed. Inspection under power is possible by arrangement. Application areas: Steel and metal construction Mechanical engineering Series and single-part production Production of large-format sheet metal parts Advantages: High press force for demanding applications Large working length for a wide range of applications Proven LVD quality and reliability Precise CNC control for reproducible results Accessories: Many tools and dies, see PDF document Sales conditions: Price applies ex foundation Dismantling, removal, loading and transport are the responsibility of the buyer Bedpfxozhtlge Aggswp Inspection possible by arrangement Delivery according to EXW (ex works)

Condition: reconditioned (used), Year of construction: 2007, operating hours: 22,605 h, functionality: fully functional, pressing force: 100 t, filling opening width: 1,100 mm, filling opening length: 1,600 mm, bale width: 1,100 mm, bale height: 1,100 mm, bale weight: 900 kg, oil tank capacity: 1,300 l, power: 75 kW (101.97 HP), year of last overhaul: 2025, For sale is a overhauled Bollegraaf baler, with 100 tonnes pressing force, large bale format 1100 x 1100 mm, 75 kW drive power and 10-fold cross binding system Technical data baler: Manufacturer Bollegraaf Typ HBC 110 K / 75 kW Year of construction 2007 Press power main press 100 tons Press power of pre-press 50 tons Operating hours 22,605 hours Feed channel 1,600 x 1,100 mm Capacity per cycle time 3,15 m³ Theoretic cycle time 19 sec. Bale size 1,100 x 1,100 mm Driving motor 75 kW Connected load 126 kW Full load current 238 A Tying system 5-fold vertical, 5-fold horizontal, fully automated Throughput rate at a bulk weight of 30 kg/cbm approx.16 tons/h bulk weight of 50 kg/cbm approx. 25 tons/h bulk weight of 100 kg/cbm approx. 47 tons/h Bale weight up to 1400 kg, depends on material and bale lenght Bjdpfezdn H Rjx Aggswp Volume oil tank approx. 1,300 l SPS controller Telemecanique TSX Micro Operating panel Schneider MAGELIS Touch Baler dimensions built up with hopper 11,750 x 5,000 x 7,105 mm (l x w x h) Transport dimensions only baler 11.750 x 2.500 x 3.450 mm (l x w x h) Machine weight baler approx. 36 tons Comments: The press was partially overhauled and serviced in our workshop and tested and stored after completion of the work. The machine is available at short notice and can be inspected in our warehouse by appointment. The following overhaul work was carried out: Rust removal and partial painting of the press. Remaining hydraulic oil tank drained, oil filter and air filter replaced. New hydraulic oil topped up. All hydraulic hoses replaced. Main hydraulic cylinder, two cylinders of the prepress flap and the cylinder of the press channel dismantled, disassembled, checked, cylinder tubes honed, all seal sets replaced and a final pressure test carried out. Disassembly of the prepress flap with bearings and bearing blocks. 1st and 3rd circular arc segmet cut out and a new one welded in again. Both bearings of the shaft of the prepress flap replaced. Upper material deflector on the frame of the prepress flap replaced. Press ram dismantled, checked and both front rollers replaced. Material deflectors and wear profiles on the sides and base of the press ram cut off and new ones welded in. Horizontal and vertical needle and tying unit dismantled, disassembled, checked, plastic sliding plates, bearings of the drill shafts and wire deflection rollers with bearings in the needle heads replaced. Both bronze slide rails on the left and right in the frame cover to the press ram replaced. Both wire deflection units on the left and right, with bale retaining clamps, completely renewed. Wire insertion unit including hydraulic cylinder under the needle feedthroughs completely renewed. Wire entry marks in the floor and side walls of the bale chamber welded shut and smoothed. General maintenance and service work carried out in accordance with the manufacturer's specifications. Press tested in manual and automatic mode, accepted and stored after completion of overhaul work. We accept no liability for the technical specifications or any errors.

Condition: excellent (used), Throughfeed press 3000 mm 14 top cylinders 6 side cylinders Water heating with heating elements in the plate Bwsdex Apxljpfx Aggjp CE marking Year of manufacture: 1996

Condition: excellent (used), Throughfeed press 3000 mm 14 top cylinders 6 side cylinders Water heating with heating elements in the plate CE marking Bedpfoza Duwox Aggjwp Year of manufacture: 1996

Condition: used, 2-station notching machine and folding machine EUROMAC type Multi 220/6R Press brake, press brake, notching machine Serial no. M11941298 Year of manufacture 1998 Cutting capacity 6 mm steel at 45 kg/mm2 4 mm for stainless steel Station I (notching) Notching angle 60° to 140° (with special blade from 30° to 140°) Knife length 220 mm Table size 950 x 640 - Manual angle adjustment via hand wheels - Notching angle with built-in blade set from 60° to 140 - Hydraulic clamping of the upper and lower knives - Automatic cutting gap adjustment - sheet hold-down device - Scaled measuring tapes embedded in the table - stop rails with angle adjustment - Operation via foot switch Station II (die bending device) Pressure force 18 ton Table size 950 x 340 Working height 1100 mm - stepless lifting speed - Infinitely adjustable stroke limiter - Stroke adjustment up to 30 mm working stroke - Reversible prism with 4x 90° prisms, length = 415 mm - 90° upper tool, length = 415 mm Motor power 4 kW Mains connection 400 Volt, 50 Hz Space requirement L x W x H 1150 x 1050 x 1460 mm Bwjdpfxomck Rys Aggep Weight approx. 1000 kg good condition

Condition: used, Year of construction: 1992, functionality: fully functional, power: 2,500 kW (3,399.05 HP), input voltage: 380 V, input current: 53 A, input frequency: 50 Hz, type of input current: three-phase, pressing force: 250 t, table length: 4,050 mm, year of last overhaul: 2007, Equipment: documentation/manual, We are offering this used Eisen u. Hammerwerk GmbH - EHT EHPS 25-40 press brake (hydraulic press brake, die bending press) for sale. Available immediately. Ready for operation. For sale due to new acquisition. Specifications: - 250 t pressing force - Cybelec DNC880S CNC control with Windows operating system (retrofitted in 2007) - Foot pedal control - Various upper tools in different lengths (segmented) - Lower tool (reversible die) in various lengths (segmented) - Hydraulic tool clamping - Support table for bent parts Technical data: - Machine type: EHPS 25-40 - Force: 2500 kN - Year of manufacture: 1992 - Working length: 4050 mm - Serial number: 207380 - Power supply: 3~ - Frequency: 50 Hz - Operating voltage: 380 V - Control voltage: 24/220 V - Rated current: 53 A - Main fuse rated current: 80 A - Circuit diagram number: 209-178/372 Bwjdey D Sy Ropfx Aggjp If you have any questions or require more information, feel free to send us a message or give us a call. Machine location at our premises: Pavic Fahrzeugtechnik Homberg GmbH Poschweg 2 34576 Homberg Relbehausen Germany This is a non-binding offer. Subject to prior sale, errors and changes excepted.

Year of construction: 1991, condition: used, machine/vehicle number: K2940, pression: 150 t working width: 4300 mm clear support width: 3600 mm support throat: 300 mm max. assembly height: ca. 500/700 mm working speed: auf-/abwaerts 41 - 65/10 mm/sec Bjdpfx Ags Dnf Uogjwp rear stop: 1000 mm electrical connection: 400 V, ca. 15 kVA kW weight: 14 t space needed: 4600 x 1950 x 3100 mm

Year of construction: 1990, condition: used, pression: 250 t working width: 3550 mm clear support width: 3050 mm support throat: 300 mm rear stop: ja mm electrical connection: 400 V, ca. 26 kW weight: 20 t space needed: 2100 x 3800 x 3100 mm Bodpo Dqaqefx Aggewp

Condition: ready for operation (used), Maximum forming capacity at full length: 9 gauge mild steel, corresponds to approx. 3.8mm, max. forming length: 3200mm, min. flange height: 6 x material thickness, clamping beam speed: maximum speed 91.44mm/s, downward speed 39.88mm/s, bending speed: 1879.6mm/s, bending angle range: 0°-180°. Dimensions X/Y/Z: approx. 5160mm/2220mm/1780mm, weight: approx. 5300kg. The machine has a front gauge, thus the bending geometry is stored and the sheet size is irrelevant. An on-site inspection is possible. Bwodpfx Ajtia Hhjggep

Condition: used, Manual swing bending machine KRAMER, type AMS 650 x 1.5 Manual swing bending machine, press brake Year of manufacture approx. 1985 Working length 650 mm Sheet thickness at 40 kg/mm2 1.5 mm Upper die opening approx. 60 mm Bending die adjustment approx. 0-25 mm Bending angle 0-180° - Upper die adjustment via hand crank - Pre-setting rail for the bending die Bwjdpsdzqaaofx Aggep - One-piece sharp bending rail, 135° Space requirement L x W x H 1200 x 600 x 1100 mm Weight 160 kg Good condition

Condition: good (used), Year of construction: 2012, machine/vehicle number: EC1-065-2500, functionality: fully functional, We are offering this well-maintained ALTEC Maschinenbau Powerline 065 PowerLine PL-065 pressure beam/gluing press from 2012. Bjdpsyuvc Ajfx Aggjwp

Condition: good (used), ManuMatik / KraussMaffei high-pressure cylinders  The high-pressure cylinders come from a commutator press and were in use there until the end.  Total height 184 cm Cylinder height 150 cm Circumference of the rod 28 cm Diameter 8.90 cm The following components are included  Check valves z2s16-1-51 Pressure reducing valve Zdr 6 dp0-45/40ym w80 Scope of delivery 1 x pressing unit Bedpfshtyxlox Aggswp Complete factory lock, large selection of storage platforms, pallet racks, shelf racks, paternosters. High quality industrial machines, lathes, grinding machines, hand machines Further articles - new and used - you will find in our shop! International shipping costs on request!

Condition: new, Press force: 300 t Bending length: 4000 mm Distance between uprights: 3250 mm Overhang: 400 mm Installation height: 590 mm Stroke: 220 mm Return stroke speed: 80 mm/s Working speed: 8 mm/s Retraction speed: 80 mm/s Drive power: 22 kW Dimensions L x W x H: approx. 4150 x 1850 x 3100 mm Weight: approx. 20,000 kg Accessories / Special features: • CNC control Cybelec Cybtouch 12 P for Y1, Y2, X + automatic crowning o Simple operation, more efficient bending, and powerful functions o Touchscreen with bright colors • 5 x 800 mm upper tool PM 1, slightly bent, R=0.8 mm, pressure load 100 t/m, tip 88° • Universal die 95 x 95 mm with multiple V-openings • Laser safety curtain FISSLER on the right and left on the front side panels • Automatic hydraulic crowning device in the lower beam • Back gauge with linear guides • 3 front support arms • Foot pedal • Painting: dark gray RAL 7031, light gray RAL 7035, yellow RAL 1033 • Operating manual • CE conformity Delivery time: approx. 2-3 months after receipt of order plus pre-carriage costs China - Germany Exclusive representation! Siegfried Volz Werkzeugmaschinen Rüschebrinkstr. 151-153 Bwodpfx Ajgiudxoggep D - 44143 Dortmund - Wambel

Condition: new, Year of construction: 2025, Sheet metal folder ZGR-3140/1.0 Bwodpfschwa Dox Aggep We have a new, high-quality folding machine of 3140 mm/ 1.0mm. This machine guarantees very high quality and agility of the work doing by the roofers. Our main task is the production of folding machines, with which we are concerned many years. The bending machine is equipped in degree scale, Romans screws, rear frame and gas struts. Directly from manufacturer! - max. working length 3140 mm - steel plate to 1.0 mm - our machines bend both a copper sheet and aluminum sheet - the total weight of machine is 600 kg - the clearance between the lower beam (fixed) and the upper beam (pressed) of 80 mm - bending angle of 145 degrees - thickness of the bending beam of 20mm - new, full machine - delivery to the client - certificate CE - TAPPING ANGLE IS FREE !! Price excl. shipping We provide invoices with 0% of tax. Delivery every week :)

Condition: used, functionality: fully functional, Offering 4 used, refurbished Flow high-pressure pumps with oil coolers, see below: Pump 1 Flow 7XD-60, 7,856 operating hours, 2 intensifiers, both operating simultaneously, 4.5 l/min, 45 kW motor, oil-water cooling, Bwsdpfx Agjzivhtogsp Pump 2 Flow 7XD-60, 25,179 operating hours, 2 intensifiers, both operating simultaneously, 4.5 l/min, 45 kW motor, oil-air cooling, Pump 3 Flow 20XR, 48,000 operating hours, 2 intensifiers, 1 is redundant as a reserve, 3.8 l/min, 37 kW motor, oil-air cooling Pump 4 Flow 20XR, 55,000 operating hours, 2 intensifiers, 1 is redundant as a reserve, 3.8 l/min, 37 kW motor, oil-air cooling Pumps are from a single original owner and are in good condition. The pumps have been completely overhauled by us and will be ready for operation in approximately 3 weeks. Prices available upon request.

Condition: excellent (used), Hertz energy-saving boiler 50 kw Bsdpfx Aeq I Nfhoggswp