Used Ess Ecomag 304 for sale (11,761)

Condition: reconditioned (used), Year of construction: 2002, operating hours: 44,590 h, functionality: fully functional, pressing force: 200 t, filling opening width: 1,020 mm, filling opening length: 2,000 mm, bale width: 1,100 mm, bale height: 1,100 mm, oil tank capacity: 3,100 l, power: 150 kW (203.94 HP), year of last overhaul: 2025, Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 112 Year of construction 2002, partially refurbished in December 2025 Operating hours 44,590 hours, stand December 2025 Press power main press 200 tons Specific press capacity 16,5 kg/cm² Feed channel 2,000 x 1,020 mm Filling volume 2,65 cm³ Theoretic throughput rate 795 m³/h Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 75 kW Tying system 5-fold horizontal, full automatic Throughput rate at MSW approx. 48 up to 54 tons/h, depends on material Volume hydraulic oil tank 3,100 l Machine weight baler approx. 50,8 tons Scope of delifery: 1 piece baler MACPRESSE, type 111A 1 operating manual with CE declaration, electrical and hydraulic circuit diagram Comments: The machine was serviced and partially overhauled in our workshop. The following work was carried out and parts replaced: • Hydraulic oil tank emptied and cleaned • Oil and air filters replaced • New hydraulic oil filled • All hydraulic hoses replaced • Press ram dismantled, broken down into individual parts, mechanics made operational • Front two main rollers replaced • Knives on the press ram replaced • Main hydraulic cylinder dismantled, disassembled, cylinder tube and piston rod checked, complete seal set replaced • Counter knife in the frame replaced • Knife gap adjusted to approx. 3 mm • Upper steel guide rails in the frame on the left and right replaced. • Worn press base cut out, base plate replaced with wear-resistant HARDOX steel. • Binding and twisting unit dismantled, broken down into individual parts, mechanics made functional, all twisting shafts and ball bearings replaced. • All wire rollers in the needle heads replaced • Wire knives cleaned and readjusted, chains greased and tensioned • All wire deflection rollers made operational • All door contact switches replaced • Wirbulator device dismantled, disassembled and made operational • General maintenance work carried out Rodex Dnb Uopfx Aa Djt Finally, the press was subjected to a machine test in manual and automatic mode, see our video for the machine function test. The documentation (BA, CE, electrical/hydraulic circuit diagram) is complete. Viewing is possible by appointment. We accept no liability for the technical specifications or any errors.

Condition: reconditioned (used), Year of construction: 1996, functionality: fully functional, pressing force: 170 t, filling opening width: 1,020 mm, filling opening length: 1,800 mm, bale width: 1,100 mm, bale height: 1,100 mm, overall weight: 40,000 kg, oil tank capacity: 3,000 l, year of last overhaul: 2024, For sale is a used baling press system consisting of a chain belt conveyor for underfloor operation, with a feed hopper, a hydraulic pre-compactor with whirlulator, a MACPRESSE 111A baling press, two complete wire drawing frames with 5 wire reel stands each, without wire. Technical data baler: Manufacturer MACPRESSE EUROPA S.R.L. Typ 111A Year of construction 1996, refurbished in 10/2024 Press power main press 170 tons Specific press capacity 14 kg/cm² Feed channel 1,800 x 1,020 mm Filling volume 2,5 cm³ Theoretic throughput rate 750 m³/h Redpfx Aou Th D Roa Djt Bale size 1,100 x 1,100 mm, length variable Driving motor 2 x 55 kW Tying system 5-fold horizontal, full automatic Throughput rate at a approx. 30 up to 35 tons/h, depends on material Volume hydraulic oil tank 3,000 l Transport dimensions of press with new machine feets 113,700 x 2,300 x 2,900 mm (l x w x h) Machine weight baler approx. 40 tons Comments: The baler was partially overhauled in our workshop and tested after completion of the work, please look at our functional video. The system was previously used to bale paper and cardboard from municipal collections. The contract was awarded elsewhere after the end of the contract period, so the complete system is for sale. The overhaul work carried out and the spare parts replaced can be found in the detailed photo documentation and in our quotation. The documentation (Manual, CE, electr./hydr.-drawings), are completely available. Inspections are possible after agreement. We will not assume liability for the given technical data and possible errors. Technical data conveyor belt: Manufacturer Wagensfeld B.V. Type chain belt conveyor 1700 mm Year of construction 2017 Drive power 7.5 kW Belt speed 14 m/minute Length of infeed conveyor 6,900 mm Length of ascending belt 12,885 mm Length of gooseneck 1,747 mm Overall length 21,271 mm Pitch 32° Effective width 1,644 mm Height of drive shaft above ground 5,777 mm Wall height of feed conveyor 500 mm Wall height of ascending conveyor 880 mm Steel flights height 40 mm Distance between flights 1200 mm Transport dimensions conveyor disassembled 15,005 x 2,503 x 2,435 mm (l x w x h) Pit dimensions 11,500 x 2,700 x 1,015 mm (l x w x d) Remarks: The chain belt conveyor, built in 2017, was later made to fit the baler during the last installation of the baler in the Netherlands and is newly installed. The conveyor belt is in good, operational condition and has therefore not been overhauled. An installation drawing with the pit dimensions is available. Scope of delifery: 1 chain belt conveyor, Wagensveld B.V. 1 piece feed hopper with pre-compressor flaps 1 piece wirbulator 1 baler MACPRESSE, type 111A 2 wire drawing frames with wire reel stands, without wire 1 operating manual with CE declaration, electrical and hydraulic circuit diagram

Condition: excellent (used), Year of construction: 1997, functionality: fully functional, Machining Center Rover 20 Working area 2,893 x 950 mm, Milling spindle with ISO30 tool holder, 3.6 kW, Drilling unit with 10 vertical and 6 horizontal drills, as well as slot saw, 6-position tool changer, The NC410 control featured a floppy disk drive and color monitor, along with basic, graphically assisted programming capabilities. Additionally, the Rover 20 already supports pendulum machining. Redpfxslc Dwnj Aa Djt Dimensions: approx. 3800 x 2000, height 1600 Control cabinet: 950 x 700 x 1300 Located at site Transport available at extra cost

Condition: ready for operation (used), Year of construction: 2006, travel distance X-axis: 450 mm, travel distance Y-axis: 300 mm, travel distance Z-axis: 300 mm, table load: 200 kg, overall weight: 2,550 kg, spindle speed (max.): 8,000 rpm, spindle motor power: 5,500 W, tool weight: 3,000 g, number of axes: 3, This 3-axis ARES-SEIKI R4530 was manufactured in 2006. It features an X-axis travel of 450 mm, Y-axis travel of 300 mm, and Z-axis travel of 300 mm. The machine includes a work table size of 600 mm x 300 mm and a maximum table load of 200 kg. If you are looking to get high-quality machining capabilities, consider the ARES-SEIKI R4530 vertical machining centre we have for sale. Contact us for further details. • Travels & Table • Work table size: 600 x 300 mm • Automatic Tool Changer (ATC) • Tool storage capacity: 10 tools Rjdpfx Aey Hi Udoa Det • Tool selection: Random, bi-directional • Max. tool diameter: 80 mm • Max. tool length: 200 mm • Tool-to-tool change time: 1.0 s • Motion & Accuracy • Rapid traverse (X/Y/Z): 30,000 mm/min • Cutting feedrate: 1–5,000 mm/min • Positioning accuracy: ±0.005/300 mm • Repeatability: ±0.002 mm • General Data • Power requirement: 15 kVA • Air pressure requirement: 5 kg/cm² Technical Specification Taper Size BT 30

Condition: used, JONES SHIPMAN 1305 EIU CYLINDRICAL GRINDING MACHINE MAKE JONES AND SHIPMAN, MADE IN ENGLAND Rjdpfx Aoy Hi Epoa Det MODEL 1305 EIU CENTRE HEIGHT 185.0 mm MAX DIAMETER 370.0 mm MAX GRINDING LENGTH 1016.0 mm MAX GRINDING WHEEL 350.0 mm x 40.0 mm GRINDING SPEED 40 – 320 RPM TABLE ROTATION 16 DEGREE TO – 12 DEGREE MAX INTENAL SPINDLE SPEED 24,000 RPM PLUS HEIDENHAIN DRO INTERNAL SPINDLE ATTACHMENT EXTENSIVE RAGE OF TOOLING AND ACCESSORIES RANGE OF MAGNETIC CHUCKS PENDANT CONTROL HYDRAULIC PACK CLEAN

Condition: used, Year of construction: 2000, Storage location: Nattheim Rodsvvi Ikopfx Aa Dot

Condition: new, neu ca. 14 - 16 Wochen ab Auf Türkei 70300 € 1328.67 € 100 to 4.5 mm 700 mm 1000 mm 210 mm 1 - 132 mm 58 1/min 6 90 mm 60 mm 300 mm 445 mm 7.5 kW 1650 mm 1545 mm 3011 mm 7000 kg Welded steel construction body frame Crankshaft made of AISI 4140 (42CrMo4) alloy steel, CNC grinded for max. precision SnBz-12 quality bronze to bearings, grinded for min surface resistance Ram supported from 6 sides Pneumatic counter-balancing of the ram 7" touchscreen Gears in oil bath Pneumatic clutch-brake combination PLC control for safety Photocell light barriers Motorized slide adjustable Mechanical overload fuse Two hand and foot pedal control Adjustable stroke (inverter) automatic centrallubrication Machine and equipment in conformity with CE-regulations Rodpjwiqq Sofx Aa Det OPTIONS: vibration pads € 192,00 bolster plate € 2.580,00

Condition: not inspected (used), functionality: unexamined, mileage: 12,000 km, power: 200 kW (271.92 HP), fuel type: diesel, overall weight: 15,000 kg, axle configuration: 6x6, fuel: diesel, Year of construction: 2011, Equipment: additional headlights, all wheel drive, cable winch, crane, differential lock, navigation system, trailer coupling, macchina perfettamente funzionante ore di esercizio in acqua 600-ore eseguito solo per dimostrazione 6 ruote motrici 4 ruote sterzanti cambio automatico ponti ZF gomme al 95% propulsione ad idrogetto (02) cambio di direzione con idrogetto orientabile DX SX pompe di sentina motore principale IVECO Redjwtthhspfx Aa Dot motore di emergenza LOMBARDINI argano anteriore gru posteriore idraulica portata 600kg con argano di sollevamento 16 posti a sedere+3 di equipaggio faro di lavoro superiore telescopico scafo in alluminio NO DOCUMENTI

Condition: good (used), Year of construction: 2015, Atlas Copco Oil Free Screw Compressor with built-in Air Dryer Model SF2+FF 7.75 bar / 112 PSI Year 2015 Redpfxey Iplfs Aa Dst 400 volts three phase, 2.2 KW / 3 HP, 2885 RPM 8.9 CFM / 4.21 lts/s Very little use Ex Pharma Facility

Condition: ready for operation (used), Year of construction: 1997, - USED - 4-AXIS HORIZONTAL MACHINING CENTRE WITH PALLET CHANGER X-AXIS TRAVEL: 1500 mm Y-AXIS TRAVEL: 1200 mm Z-AXIS TRAVEL: 1250 mm SPINDLE: 10-4000 rpm; 40 kW; HSK-A 100 PALLET: CONTINUOUS ; 1000X1000 mm; 1-500 rpm MAX ADMITTED LOAD: 2000 Kg TOOL MAGAZINE: CHAIN-TYPE ; 161 POS CONTROL UNIT: SIEMENS 840 C OVERALL DIMENSIONS: 8500 x 4800 x 4800 mm ACCESSORIES: SWARF CONVEYOR ; PAPER FILTER NOTE: COMPLETELY OVERHAULED MACHINE; HORIZONTAL AND VERTICAL AUTOMATIC HEAD; TURNING TABLE Rsdjh Hfrnepfx Aa Dst

Year of construction: 2009, condition: used, Sawing system for aluminum with 2 saw motors that independently perform a 45° cut. Material feed unit with up to 8,100 mm Cross conveyor, storage table, chip conveyor and extraction Soundproof cabin Control via Siemens S7 panel Rsdpsqzmnujfx Aa Det Operating instructions etc. available, further technical data on request Machine was in operation until dismantling Further technical data on request or see photos

Condition: used, Year of construction: 2011, functionality: unexamined, input voltage: 400 V, input frequency: 50 Hz, Equipment: CE marking, lightly used Biesse CNC machine, model Skill 300, year of manufacture 2011. Taken as a trade-in from a Dutch customer when purchasing a new machine. 3-axis machining center with 6 support beams, milling motor, drilling unit, etc. Automatic tool changer (ISO30) Automatic lubrication Vacuum pump (Becker) Safety mats Remote control Computer (HP) and mobile console Redpsy Ihu Eefx Aa Det Relatively compact machine, immediately available in Barneveld for loading.

Condition: used, Year of construction: 2000, table width: 2,700 mm, table length: 3,300 mm, total length: 3,800 mm, total width: 1,000 mm, total height: 2,700 mm, overall weight: 1,500 kg, No. 3272 Perforated plate press Hess JULIA Used, year of construction 2000 Dimensions of the perforated plate 3300 x 2700 mm LW 4 manual hydraulic cylinders (2 in need of repair) 12 pneumatic cylinders (2 magnetic and with angle adjustment) Transport dimensions approx. 3800 x 1000 x 2700 mm LWH Weight approx. 1500 kg Sale on behalf of customer, ex location near 71063 Sindelfingen, without dismantling, without transport and assembly Dismantling, loading, and transport by us optionally available Subject to errors in the description and price To avoid any misunderstandings, an on-site inspection is possible and recommended by appointment Redpfx Aajy E N Ize Dst Sold as is Technical specifications, condition description, year of construction and scope of delivery according to the manufacturer’s brochure or previous owner, without guarantee Subject to prior sale For used machines, any warranty is excluded, the following applies: “sold as seen” Photos and videos serve as examples and do not represent the actual scope of delivery Terms of payment: Prices plus VAT, payment before collection or shipping Terms of delivery: Ex location

Condition: ready for operation (used), Year of construction: 2002, number of axes: 3, total width: 1,500 mm, overall weight: 710 kg, product length (max.): 3,390 mm, This 3-axis BIESSE Rover 24S was manufactured in 2002. It features a length of 3390 mm and an overall width of 1500 mm, with a conveyor speed ranging from 28 to 140 m/min. The machine has a weight of 710 kg and is equipped with a powerful 1.1 kW motor. If you are looking to get high-quality CNC processing capabilities, consider the BIESSE Rover 24S machine we have for sale. Contact us for further details. • Overall width: 1500 mm • Conveyor height: 890 + 940 mm • Conveyor speed: 28–140 m/min • Conveyor drive motor: 0.75 kW • Exhaust fan duty: 5,500 m³/h • Motor: 1.1 kW • Minimum working length: 700 mm • Compressed air connection: 1/2" Rjdey E Nydepfx Aa Dot • Compressed air consumption: tab. 1 • Electric power supply cable section: 4 x 1.5

Condition: used, machine/vehicle number: 008389, X axis working area: 8417 mm Y axis working area: 1930 mm Redpsyqxxrjfx Aa Det Working Table: Pod and Rail Main Electrospindle power: 13.2 KW Number of controlled axes: 4 axes Maximum edge height: 60 mm Total number of drilling spindles: 40 Total number of tool changer positions: 22

Condition: used, Year of construction: 2022, total length: 8,000 mm, total width: 2,400 mm, total height: 2,400 mm, Weight: 3.969 kg Price: On request What are Presale Items at Second Owner? Presale items are machines that we sell in their current condition ("as-is"). We have purchased these machines based solely on photos and sell them with the information provided in the advertisement. Unfortunately, we do not have additional details, such as exact dimensions or machine specifications. Additionally, these machines are often not yet in stock and have not been inspected by us. These machines are offered at competitive prices, which means the prices are lower than usual, but the risk lies entirely with the buyer. Please carefully review the information in the advertisement before making a purchase. If you have any questions, feel free to contact us! - Year: 2022 - Documentation available: Yes - CE marking present: Yes Redpfjy E Hdgsx Aa Dst - CE certificate present: No - Serial number: 1000056636 - Max. cutting length [mm]: 3200 - Max. cutting width [mm]: 3200 - Transport dimensions: 8000mm x 2400mm x 2400mm (l x w x h) - Transport weight [kg]: 3969kg - Transport packages [pcs.]: 4 Financial information VAT: The price shown is exclusive of VAT VAT/margin: VAT deductible for entrepreneurs Delivery and trade-in always possible for everything in the industrial sectors Glenn Smeets

Condition: excellent (used), Year of construction: 2013, Airpress APK-G 50/500 Compressor Machine mounted on 500L tank, serviced and equipped with air dryer. Technical specifications: Capacity: 1.9 m3/min (1900/min) Motor power: 15 KW Pressure: 10 bar Operating hours: 4427 h Year: 2013 Net price: 13,700 Gross price: 16,851 The compressor is fully functional, Rjdjy Idlyopfx Aa Djt service support provided. Video below

Condition: good (used), pressing force: 1,250 t, Pressing force: max. 1250 t Width: 585 mm. height max. 480 mm. Stroke: max. 355 mm. Weight: 7200 kg. Redpfxoy Ia Sie Aa Dst

Condition: excellent (used), Year of construction: 2000, functionality: fully functional, C-frame press for clinching technology Pressing force: 4.8 t Air pressure: 6 bar Total stroke: 32 mm Power stroke: 3 mm Redpfsy Ey Hzsx Aa Dot No tools included

Condition: used, machine/vehicle number: 008374, Max. panel width: 1000 mm Max. panel length: 2500 mm Redsyng Amjpfx Aa Dst

Condition: used, machine/vehicle number: 007354, Type of edging: Thin edge, Thick edge Gluing System: EVA Hotmelt Corner Rounding Unit: yes Combination Squaring Edgebanding Machine: First and Second Pass Max Panel Width: 240 mm Max feed speed: 40 m/min Operating Units Right Side: 9 nr Operating Units Left Side: 9 nr Rodpfx Aajyg Edaj Djt

Condition: excellent (used), Dewar Tank for Liquid Nitrogen, Cryogenic, Cryotherm Apollo For sale: Cryotherm Apollo Dewar vessel, 200 liters, year of manufacture 1999. Model: Apollo 200 Serial Number: 46748 Empty weight: 94 kg Rodsy H Hlaspfx Aa Djt Working overpressure: Internal 1.0 bar / External -1 bar Operating temperature: Internal -196 °C / External +20 °C Medium: Liquid Nitrogen (LIN) Capacity: 198 liters Manufactured by Messer Griesheim GmbH, Germany We also offer other tanks for LIN (liquid nitrogen), LOX (liquid oxygen), LAR (liquid argon), LNG (liquefied natural gas) as well as for CO2 (carbon dioxide), argon, oxygen, nitrogen, carbon dioxide, hydrogen, and methane.

Year of construction: 2006, condition: good (used), functionality: fully functional, Working area approx. 600 mm x 600 mm Rjdpfoy H Engox Aa Dot

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 292500 € 30 to 3000x1500 mm 3000 mm 1500 mm 70 m/Min 60 m/Min 120 m/Min 40 mm 1200 1/Min 325 1/Min 2800 1/Min 6 mm 3 mm 3 mm 1.5 mm 28 0,1 mm 0,05 mm 22 U/Min 150 U/Min 200 kg 940 mm 6 bar 88.9 mm 15 kW 180 l Redpfx Aasynna He Dst 6650 mm 7650 mm 6300 mm 8300 mm 2310 mm 18250 kg Control unit, Siemens Sinumerik 840 D SL CAD-CAM software Programming on the control panel Remote diagnostic function Automatic clamp positioning Network Ethernet communication Automatic tool lubrication UPS for control panel Movable scrap box Brush table Oil Cooler USB Driver Command pedal Web cam for service Reposition on X axis Alignment Tools for Index Station D Manual nesting turret (27 stations without tool and holder): 11 x A-Station fix: 0,8-12,7 mm 11 x B-Station fix: 12,8 - 31,7 mm 2 x C-Station fix: 31,8 - 50,8 mm 1 x D-Station fix: 50,9 - 88,9 mm 3 x D-Station Index: 50,9 - 88,9 mm Infra-red light barriers according to CE rules PRICE FCA TÜRKIYE

Condition: new, neu ca. 12 - 14 Wochen ab Auf Türkei 249800 € 30 to 2500x1250 mm 2500 mm 1250 mm 116 m/Min 80 m/Min 140 m/Min 40 mm 1200 1/Min 425 1/Min 3200 1/Min 6 mm 3 mm 3 mm 1.5 mm 27 0,1 mm 0,05 mm 22 U/Min Redpfx Ajynnaysa Dst 150 U/Min 120 kg 940 mm 6 bar 88.9 mm 15 kW 5750 mm 6800 mm 5360 mm 7360 mm 2310 mm 12960 kg Control unit, Siemens Sinumerik 840 D SL CAD-CAM software Programming on the control panel Remote diagnostic function Automatic clamp positioning Network Ethernet communication Automatic tool lubrication UPS for control panel Movable scrap box Brush table Oil Cooler USB Driver Command pedal Web cam for service Reposition on X axis Alignment Tools for Index Station D Manual nesting turret (27 stations without tool and holder): 11 x A-Station fix: 0,8-12,7 mm 11 x B-Station fix: 12,8 - 31,7 mm 2 x C-Station fix: 31,8 - 50,8 mm 1 x D-Station fix: 50,9 - 88,9 mm 3 x D-Station index: 50,9 - 88,9 mm Infra-red light barriers according to CE rules Price FCA Türkiye